Abstract: The Philosophy of Sufficiency Economy, bestowed
by His Majesty the King Bhumibol Adulyadej to the people of
Thailand, highlights a balanced way of living. Three principles of
moderation reasonableness, and immunity, along with the conditions
for morality and knowledge, can be applied to any level of the
society–from an individual to the nation. The Philosophy of
Sufficiency Economy helps address the current development
challenges, which are issues on institutions, environmental
sustainability, human well-being, and the role of the government.
Abstract: The degradation of selected pharmaceuticals in some
water matrices was studied by using several chemical treatments. The
pharmaceuticals selected were the beta-blocker metoprolol, the
nonsteroidal anti-inflammatory naproxen, the antibiotic amoxicillin,
and the analgesic phenacetin; and their degradations were conducted
by using UV radiation alone, ozone, Fenton-s reagent, Fenton-like
system, photo-Fenton system, and combinations of UV radiation and
ozone with H2O2, TiO2, Fe(II), and Fe(III). The water matrices, in
addition to ultra-pure water, were a reservoir water, a groundwater,
and two secondary effluents from two municipal WWTP. The results
reveal that the presence of any second oxidant enhanced the
oxidation rates, with the systems UV/TiO2 and O3/TiO2 providing the
highest degradation rates. It is also observed in most of the
investigated oxidation systems that the degradation rate followed the
sequence: amoxicillin > naproxen > metoprolol > phenacetin. Lower
rates were obtained with the pharmaceuticals dissolved in natural
waters and secondary effluents due to the organic matter present
which consume some amounts of the oxidant agents.
Abstract: Kojic acid is an organic acid that is widely used as an ingredient for dermatological products, precursor for flavor enhancer and also as anti-inflammatory drug. The present study was undertaken to test the feasibility of pineapple residues as substrate for kojic acid production by Aspergillus flavus Link 44-1 via solid-state fermentation. The effect of initial moisture content, pH and incubation time on kojic acid fermentation was investigated. The best initial moisture content for kojic acid production from pineapple residues was observed at 70% (v/w) whereas initial culture pH 2.5 was identified to give high production of kojic acid. The optimal range of incubation time was identified between 8 and 14 days of incubation which corresponded to highest range of kojic acid produced. The results from this study pronounce the promising usability of pineapple residues as alternative substrate for kojic acid production by A. flavus Link 44-1.
Abstract: As the network based technologies become
omnipresent, demands to secure networks/systems against threat
increase. One of the effective ways to achieve higher security is
through the use of intrusion detection systems (IDS), which are a
software tool to detect anomalous in the computer or network. In this
paper, an IDS has been developed using an improved machine
learning based algorithm, Locally Linear Neuro Fuzzy Model
(LLNF) for classification whereas this model is originally used for
system identification. A key technical challenge in IDS and LLNF
learning is the curse of high dimensionality. Therefore a feature
selection phase is proposed which is applicable to any IDS. While
investigating the use of three feature selection algorithms, in this
model, it is shown that adding feature selection phase reduces
computational complexity of our model. Feature selection algorithms
require the use of a feature goodness measure. The use of both a
linear and a non-linear measure - linear correlation coefficient and
mutual information- is investigated respectively
Abstract: Buildings with floating column are highly undesirable built in seismically active areas. Many urban multi-storey buildings today have floating column buildings which are adopted to accommodate parking at ground floor or reception lobbies in the first storey. The earthquake forces developed at different floor levels in a building need to be brought down along the height to the ground by the shortest path; any deviation or discontinuity in this load transfer path results in poor performance of the building. Floating column buildings are severely damaged during earthquake. Damage on this structure can be reduce by taking the effect of infill wall. This paper presents the effect of stiffness of infill wall to the damage occurred in floating column building when ground shakes. Modelling and analysis are carried out by non linear analysis programme IDARC-2D. Damage occurred in beams, columns, storey are studied by formulating modified Park & Ang model to evaluate damage indices. Overall structural damage indices in buildings due to shaking of ground are also obtained. Dynamic response parameters i.e. lateral floor displacement, storey drift, time period, base shear of buildings are obtained and results are compared with the ordinary moment resisting frame buildings. Formation of cracks, yield, plastic hinge, are also observed during analysis.
Abstract: This paper addresses the problem of recognizing and
interpreting the behavior of human workers in industrial
environments for the purpose of integrating humans in software
controlled manufacturing environments. In this work we propose a
generic concept in order to derive solutions for task-related manual
production applications. Thus, we are able to use a versatile concept
providing flexible components and being less restricted to a specific
problem or application. We instantiate our concept in a spot welding
scenario in which the behavior of a human worker is interpreted
when performing a welding task with a hand welding gun. We
acquire signals from inertial sensors, video cameras and triggers and
recognize atomic actions by using pose data from a marker based
video tracking system and movement data from inertial sensors.
Recognized atomic actions are analyzed on a higher evaluation level
by a finite state machine.
Abstract: High purity hydrogen and the valuable by-product of carbon nanotubes (CNTs) can be produced by the methane catalytic decomposition. The methane conversion and the performance of CNTs were determined by the choices of catalysts and the condition of decomposition reaction. In this paper, Ni/MgO and Ni/O-D (oxidized diamond) catalysts were prepared by wetness impregnation method. The effects of reaction temperature and space velocity of methane on the methane conversion were investigated in a fixed-bed. The surface area, structure and micrography were characterized with BET, XPS, SEM, EDS technology. The results showed that the conversion of methane was above 8% within 150 min (T=500) for 33Ni/O-D catalyst and higher than 25% within 120 min (T=650) for 41Ni/MgO catalyst. The initial conversion increased with the increasing temperature of the decomposition reaction, but their catalytic activities decreased rapidly while at too higher temperature. To decrease the space velocity of methane was propitious to promote the methane conversion, but not favor of the hydrogen yields. The appearance of carbon resulted from the methane decomposition lied on the support type and the condition of catalytic reaction. It presented as fiber shape on the surface of Ni/O-D at the relatively lower temperature such as 500 and 550, but as grain shape stacked on and overlayed on the surface of the metal nickel while at 650. The carbon fiber can form on the Ni/MgO surface at 650 and the diameter of the carbon fiber increased with the decreasing space velocity.
Abstract: A new mechanism responsible for structural life
consumption due to resonant fatigue in turbine blades, or vanes, is
presented and explained. A rotating blade or vane in a gas turbine can
change its contour due to erosion and/or material build up, in any of
these instances, the surface pressure distribution occurring on the
suction and pressure sides of blades-vanes can suffer substantial
modification of their pressure and temperatures envelopes and flow
characteristics. Meanwhile, the relative rotation between the blade
and duct vane while the pressurized gas flows and the consequent
wake crossings, will induce a fluctuating thrust force or lift that will
excite the blade.
An actual totally used up set of vane-blade components in a HP
turbine power stage in a gas turbine is analyzed. The blade suffered
some material erosion mostly at the trailing edge provoking a
peculiar surface pressure envelope which evolved as the relative
position between the vane and the blade passed in front of each other.
Interestingly preliminary modal analysis for this eroded blade
indicates several natural frequencies within the aeromechanic power
spectrum, moreover, the highest frequency component is 94% of one
natural frequency indicating near resonant condition.
Independently of other simultaneously occurring fatigue cycles
(such as thermal, centrifugal stresses).
Abstract: A analysis on the conventional the blood pressure estimation method using an oscillometric sphygmomanometer was
performed through a computer simulation using an arterial pressure-volume (APV) model. Traditionally, the maximum amplitude algorithm (MAP) was applied on the oscillation waveforms of the APV model to obtain the mean arterial pressure and the characteristic ratio. The estimation of mean arterial pressure and
characteristic ratio was significantly affected with the shape of the blood pressure waveforms and the cutoff frequency of high-pass filter
(HPL) circuitry. Experimental errors are due to these effects when estimating blood pressure. To find out an algorithm independent from
the influence of waveform shapes and parameters of HPL, the volume
oscillation of the APV model and the phase shift of the oscillation with fast fourier transform (FFT) were testified while increasing the cuff
pressure from 1 mmHg to 200 mmHg (1 mmHg per second). The phase shift between the ranges of volume oscillation was then only observed between the systolic and the diastolic blood pressures. The same results were also obtained from the simulations performed on two different the arterial blood pressure waveforms and one
hyperthermia waveform.
Abstract: This work was to study batch biosorption of Pb(II)
ions from aqueous solution by Luffa charcoal. The effect of operating
parameters such as adsorption contact time, initial pH solution and
different initial Pb(II) concentration on the sorption of Pb(II) were
investigated. The results showed that the adsorption of Pb(II) ions
was initially rapid and the equilibrium time was 10 h. Adsorption
kinetics of Pb(II) ions onto Luffa charcoal could be best described by
the pseudo-second order model. At pH 5.0 was favorable for the
adsorption and removal of Pb(II) ions. Freundlich adsorption
isotherm model was better fitted for the adsorption of Pb(II) ions than
Langmuir and Timkin isotherms, respectively. The highest monolayer
adsorption capacity obtained from Langmuir isotherm model was
51.02 mg/g. This study demonstrated that Luffa charcoal could be
used for the removal of Pb(II) ions in water treatment.
Abstract: Visfatin and apelin are two new adipokines that recently gained a special interest in diabetes research. This study was conducted to study the interplay between these two adipokines and their correlation with other inflammatory and biochemical parameters in type 2 diabetic (T2D) postmenopausal women with CAD. Visfatin and apelin were measured by enzyme-linked immunoassay (ELISA). Visfatin was found to be significantly higher in the following groups: T2D patients without CAD, non-obese and obese T2D patients with CAD when compared to control group. Apelin was found to be significantly lower in non-obese and obese T2D patients with CAD when compared to control group. Visfatin and apelin were found to be significantly associated with each other and with other biochemical parameters. The current study provides evidence for the interplay between visfatin and apelin through the inflammatory milieu characteristic of T2D and their possible role in the pathogenesis of CAD complication of T2D.
Abstract: Metal cutting is a severe plastic deformation process
involving large strains, high strain rates, and high temperatures.
Conventional analysis of the chip formation process is based on bulk
material deformation disregarding the inhomogeneous nature of the
material microstructure. A series of orthogonal cutting tests of AISI
1045 and 1144 steel were conducted which yielded similar process
characteristics and chip formations. With similar shear angles and cut
chip thicknesses, shear strains for both chips were found to range
from 2.0 up to 2.8. The manganese-sulfide (MnS) precipitate in the
1144 steel has a very distinct and uniform shape which allows for
comparison before and after chip formation. From close observations
of MnS precipitates in the cut chips it is shown that the conventional
approach underestimates plastic strains in metal cutting.
Experimental findings revealed local shear strains around a value of
6. These findings and their implications are presented and discussed.
Abstract: One year (November 2009-October 2010) sediment monitoring was used to evaluate pollution status, concentration and distribution of heavy metals (As, Cu, Cd, Cr, Hg, Ni, Pb and Zn) in West Port of Malaysia. Sediment sample were collected from nine stations every four months. Geo-accumulation factor and Pollution Load Index (PLI) were estimated to better understand the pollution level in study area. The heavy metal concentration (Mg/g dry weight) were ranged from 20.2 to 162 for As, 7.4 to 27.6 for Cu, 0.244 to 3.53 for Cd, 11.5 to 61.5 for Cr, 0.11 to 0.409 for Hg, 7.2 to 22.2 for Ni, 22.3 to 80 for Pb and 23 to 98.3 for Zn. In general, concentration some metals (As,Cd, Hg and Pb) was higher than background values that are considered as serious concern for aquatic life and the human health.
Abstract: Fuel cells have become one of the major areas of
research in the academia and the industry. The goal of most fish
farmers is to maximize production and profits while holding labor
and management efforts to the minimum. Risk of fish kills, disease
outbreaks, poor water quality in most pond culture operations,
aeration offers the most immediate and practical solution to water
quality problems encountered at higher stocking and feeding rates.
Many units of aeration system are electrical units so using a
continuous, high reliability, affordable, and environmentally friendly
power sources is necessary. Aeration of water by using PEM fuel cell
power is not only a new application of the renewable energy, but
also, it provides an affordable method to promote biodiversity in
stagnant ponds and lakes. This paper presents a new design and
control of PEM fuel cell powered a diffused air aeration system for a
shrimp farm in Mersa Matruh in Egypt. Also Artificial intelligence
(AI) techniques control is used to control the fuel cell output power
by control input gases flow rate. Moreover the mathematical
modeling and simulation of PEM fuel cell is introduced. A
comparison study is applied between the performance of fuzzy logic
control (FLC) and neural network control (NNC). The results show
the effectiveness of NNC over FLC.
Abstract: CO2 is the primary anthropogenic greenhouse gas,
accounting for 77% of the human contribution to the greenhouse
effect in 2004. In the recent years, global concentration of CO2 in the
atmosphere is increasing rapidly. CO2 emissions have an impact on
global climate change. Anthropogenic CO2 is emitted primarily from
fossil fuel combustion. Carbon capture and storage (CCS) is one
option for reducing CO2 emissions. There are three major approaches
for CCS: post-combustion capture, pre-combustion capture and
oxyfuel process. Post-combustion capture offers some advantages as
existing combustion technologies can still be used without radical
changes on them.
There are several post combustion gas separation and capture
technologies being investigated, namely; (a) absorption, (b)
cryogenic separation, (c) membrane separation (d) micro algal biofixation
and (e) adsorption. Apart from establishing new techniques,
the exploration of capture materials with high separation performance
and low capital cost are paramount importance. However, the
application of adsorption from either technology, require easily
regenerable and durable adsorbents with a high CO2 adsorption
capacity. It has recently been reported that the cost of the CO2
capture can be reduced by using this technology. In this paper, the
research progress (from experimental results) in adsorbents for CO2
adsorption, storage, and separations were reviewed and future
research directions were suggested as well.
Abstract: There-s a lack in understanding the indoor climate of Malaysian residential. The assumption of traditional house could
provide the best indoor environment is too good to be true. This research is to understand indoor environment in three types of
Malaysian residential and thermo recorder TR72Ui were placed in
indoor spaces for measurement. There are huge differences of indoor
environment between housing types, and building material helps to control indoor climate. Traditional house indoor climate was similar to
the outdoor. Temperature in the bedroom of terrace and town houses were slightly higher than the living room. Indoor temperature was 2oC
lower in the rainy season than the hot season. It was hard to control
indoor humidity level in traditional house compared with terrace and
town house. As for conclusion, town house provides the best thermal
environment to the building occupants and can be improved with good
roof insulation.
Abstract: Duplicated region detection is a technical method to
expose copy-paste forgeries on digital images. Copy-paste is one
of the common types of forgeries to clone portion of an image
in order to conceal or duplicate special object. In this type of
forgery detection, extracting robust block feature and also high
time complexity of matching step are two main open problems.
This paper concentrates on computational time and proposes a local
block matching algorithm based on block clustering to enhance time
complexity. Time complexity of the proposed algorithm is formulated
and effects of two parameter, block size and number of cluster, on
efficiency of this algorithm are considered. The experimental results
and mathematical analysis demonstrate this algorithm is more costeffective
than lexicographically algorithms in time complexity issue
when the image is complex.
Abstract: This paper presents the combination of different precipitation data sets and the distributed hydrological model, in order to examine the flood runoff reproductivity of scattered observation catchments. The precipitation data sets were obtained from observation using rain-gages, satellite based estimate (TRMM), and numerical weather prediction model (NWP), then were coupled with the super tank model. The case study was conducted in three basins (small, medium, and large size) located in Central Vietnam. Calculated hydrographs based on ground observation rainfall showed best fit to measured stream flow, while those obtained from TRMM and NWP showed high uncertainty of peak discharges. However, calculated hydrographs using the adjusted rainfield depicted a promising alternative for the application of TRMM and NWP in flood modeling for scattered observation catchments, especially for the extension of forecast lead time.
Abstract: A mathematical model for determining the overall efficiency
of a multistage tractor gearbox including all gear, lubricant,
surface finish related parameters and operating conditions is
presented. Sliding friction, rolling friction and windage losses were
considered as the main sources of power loss in the gearing system. A
computer code in FORTRAN was developed to simulate the model.
Sliding friction contributes about 98% of the total power loss for
gear trains operating at relatively low speeds (less than 2000 rpm
input speed). Rolling frictional losses decrease with increased load
while windage losses are only significant for gears running at very
high speeds (greater than 3000 rpm). The results also showed that the
overall efficiency varies over the path of contact of the gear meshes
ranging between 94% to 99.5%.
Abstract: detecting the deadlock is one of the important
problems in distributed systems and different solutions have been
proposed for it. Among the many deadlock detection algorithms,
Edge-chasing has been the most widely used. In Edge-chasing
algorithm, a special message called probe is made and sent along
dependency edges. When the initiator of a probe receives the probe
back the existence of a deadlock is revealed. But these algorithms are
not problem-free. One of the problems associated with them is that
they cannot detect some deadlocks and they even identify false
deadlocks. A key point not mentioned in the literature is that when
the process is waiting to obtain the required resources and its
execution has been blocked, how it can actually respond to probe
messages in the system. Also the question of 'which process should
be victimized in order to achieve a better performance when multiple
cycles exist within one single process in the system' has received
little attention. In this paper, one of the basic concepts of the
operating system - daemon - will be used to solve the problems
mentioned. The proposed Algorithm becomes engaged in sending
probe messages to the mandatory daemons and collects enough
information to effectively identify and resolve multi-cycle deadlocks
in distributed systems.