Abstract: The H.264/AVC video coding standard contains a number of advanced features. Ones of the new features introduced in this standard is the multiple intramode prediction. Its function exploits directional spatial correlation with adjacent block for intra prediction. With this new features, intra coding of H.264/AVC offers a considerably higher improvement in coding efficiency compared to other compression standard, but computational complexity is increased significantly when brut force rate distortion optimization (RDO) algorithm is used. In this paper, we propose a new fast intra prediction mode decision method for the complexity reduction of H.264 video coding. for luma intra prediction, the proposed method consists of two step: in the first step, we make the RDO for four mode of intra 4x4 block, based the distribution of RDO cost of those modes and the idea that the fort correlation with adjacent mode, we select the best mode of intra 4x4 block. In the second step, we based the fact that the dominating direction of a smaller block is similar to that of bigger block, the candidate modes of 8x8 blocks and 16x16 macroblocks are determined. So, in case of chroma intra prediction, the variance of the chroma pixel values is much smaller than that of luma ones, since our proposed uses only the mode DC. Experimental results show that the new fast intra mode decision algorithm increases the speed of intra coding significantly with negligible loss of PSNR.
Abstract: In this paper, an automated system is presented for
identification and separation of plastic resins based on near infrared
(NIR) reflectance spectroscopy. For identification and separation
among resins, a "Two-Filter" identification method is proposed that
is capable to distinguish among polyethylene terephthalate (PET),
high density polyethylene (HDPE), polyvinyl chloride (PVC),
polypropylene (PP) and polystyrene (PS). Through surveying effects
of parameters such as surface contamination, sample thickness, label
and cap existence, it was obvious that the "Two-Filter" method has a
high efficiency in identification of resins. It is shown that accurate
identification and separation of five major resins can be obtained
through calculating the relative reflectance at two wavelengths in the
NIR region.
Abstract: The acid rain causes change in pH level of soil it is
directly influence on root and leaf growth. Yield of the crop was
reduced if acidity of soil is more. Acid rain seeps into the earth and
poisons plants and trees by dissolving toxic substances in the soil,
such as aluminum, which get absorbed by the roots. In present
investigation, effect of acid rain on crop Vigna radiata was studied.
The effect of acid rain on change in soil fertility was detected in
which pH of control sample was 6.5 and pH of 1% H2SO4 and 1%
HNO3 were 3.5. Nitrogen nitrate in soil was high in 1% HNO3 treated
soil & Control sample. Ammonium nitrogen in soil was low in 1%
HNO3 & H2SO4 treated soil. Ammonium nitrogen was medium in
control and other samples. The effect of acid rain on seed
germination on 3rd day of germination control sample growth was
6.1cm with plumule 0.001% HNO3 & 0.001% H2SO4 was 5.5cm
with plumule and 8cm with plumule. On 10th day fungal growth was
observed in 1% and 0.1% H2SO4 concentrations when all plants were
dead. The effect of acid rain on crop productivity was investigated on
3rd day roots were developed in plants. On 12th day Vigna radiata
showed more growth in 0.1% HNO3 and 0.1% H2SO4 treated plants
as compare to control plants. On 20th day development of
discoloration of plant pigments were observed on acid treated plants
leaves. On 34th day Vigna radiata showed flower in 0.1% HNO3,
0.01% HNO3 and 0.01% H2SO4treated plants and no flowers were
observed on control plants. On 42th day 0.1% HNO3, 0.01% HNO
and 0.01% H2SO4 treated Vigna radiata variety and control plants
were showed seeds on plants. In Vigna radiate variety 0.1%, 0.01%
HNO3, 0.01% H2SO4treated plants were dead on 46th day and fungal
growth was observed. The toxicological study was carried out on
Vigna radiata plants exposed to 1% HNO3 cells were damaged more
than 1% H2SO4. Leaf sections exposed to 0.001% HNO3 & H2SO4
showed less damaged of cells and pigmentation observed in entire
slide when compare with control plant.
Abstract: The residue number system (RNS), due to its
properties, is used in applications in which high performance
computation is needed. The carry free nature, which makes the
arithmetic, carry bounded as well as the paralleling facility is the
reason of its capability of high speed rendering. Since carry is not
propagated between the moduli in this system, the performance is
only restricted by the speed of the operations in each modulus. In this
paper a novel method of number representation by use of redundancy
is suggested in which {rn- 2,rn-1,rn} is the reference moduli set
where r=2k+1 and k =1, 2,3,.. This method achieves fast
computations and conversions and makes the circuits of them much
simpler.
Abstract: Vibration characteristics of subcooled flow boiling on
thin and long structures such as a heating rod were recently
investigated by the author. The results show that the intensity of the
subcooled boiling-induced vibration (SBIV) was influenced strongly
by the conditions of the subcooling temperature, linear power density
and flow velocity. Implosive bubble formation and collapse are the
main nature of subcooled boiling, and their behaviors are the only
sources to originate from SBIV. Therefore, in order to explain the
phenomenon of SBIV, it is essential to obtain reliable information
about bubble behavior in subcooled boiling conditions. This was
investigated at different conditions of coolant subcooling
temperatures of 25 to 75°C, coolant flow velocities of 0.16 to
0.53m/s, and linear power densities of 100 to 600 W/cm. High speed
photography at 13,500 frames per second was performed at these
conditions. The results show that even at the highest subcooling
condition, the absolute majority of bubbles collapse very close to the
surface after detaching from the heating surface. Based on these
observations, a simple model of surface tension and momentum
change is introduced to offer a rough quantitative estimate of the
force exerted on the heating surface during the bubble ebullition. The
formation of a typical bubble in subcooled boiling is predicted to
exert an excitation force in the order of 10-4 N.
Abstract: Carbon dioxide is one of the major green house gases.
It is removed from different streams using amine absorption process.
Sterically hindered amines are suggested as good CO2 absorbers.
Solubility of carbon dioxide (CO2) was measured in aqueous
solutions of 2-Amino-2-methyl-1-propanol (AMP) at temperatures 30
oC, 40 oC and 60 oC. The effect of pressure and temperature was
studied over various concentrations of AMP. It has been found that
pressure has positive effect on CO2 solubility where as solubility
decreased with increasing temperature. Absorption performance of
AMP increased with increasing pressure. Solubility of aqueous AMP
was compared with mo-ethanolamine (MEA) and the absorption
capacity of aqueous solutions of AMP was found to be better.
Abstract: Rapid steps made in the field of Information and Communication Technology (ICT) has facilitated the development of teaching and learning methods and prepared them to serve the needs of an assorted educational institution. In other words, the information age has redefined the fundamentals and transformed the institutions and method of services delivery forever. The vision is the articulation of a desire to transform the method of teaching and learning could proceed through e-learning. E-learning is commonly deliberated to use of networked information and communications technology in teaching and learning practice. This paper deals the general aspects of the e-leaning with its issues, developments, opportunities and challenges, which can the higher institutions own.
Abstract: This paper presents a new method to detect high impedance faults in radial distribution systems. Magnitudes of third and fifth harmonic components of voltages and currents are used as a feature vector for fault discrimination. The proposed methodology uses a learning vector quantization (LVQ) neural network as a classifier for identifying high impedance arc-type faults. The network learns from the data obtained from simulation of a simple radial system under different fault and system conditions. Compared to a feed-forward neural network, a properly tuned LVQ network gives quicker response.
Abstract: The evaluation of conversational agents or chatterbots question answering systems is a major research area that needs much attention. Before the rise of domain-oriented conversational agents based on natural language understanding and reasoning, evaluation is never a problem as information retrieval-based metrics are readily available for use. However, when chatterbots began to become more domain specific, evaluation becomes a real issue. This is especially true when understanding and reasoning is required to cater for a wider variety of questions and at the same time to achieve high quality responses. This paper discusses the inappropriateness of the existing measures for response quality evaluation and the call for new standard measures and related considerations are brought forward. As a short-term solution for evaluating response quality of conversational agents, and to demonstrate the challenges in evaluating systems of different nature, this research proposes a blackbox approach using observation, classification scheme and a scoring mechanism to assess and rank three example systems, AnswerBus, START and AINI.
Abstract: The antioxidant compounds are needed for the food, beverages, and pharmaceuticals industry. For this purpose, an appropriate method is required to measure the antioxidant properties in various types of samples. Spectrophotometric method usually used has some weaknesses, including the high price, long sample preparation time, and less sensitivity. Among the alternative methods developed to overcome these weaknesses is antioxidant biosensor based on superoxide dismutase (SOD) enzyme. Therefore, this study was carried out to measure the SOD activity originating from Deinococcus radiodurans and to determine its kinetics properties. Carbon paste electrode modified with ferrocene and immobilized SOD exhibited anode and cathode current peak at potential of +400 and +300mv respectively, in both pure SOD and SOD of D. radiodurans. This indicated that the current generated was from superoxide catalytic dismutation reaction by SOD. Optimum conditions for SOD activity was at pH 9 and temperature of 27.50C for D. radiodurans SOD, and pH 11 and temperature of 200C for pure SOD. Dismutation reaction kinetics of superoxide catalyzed by SOD followed the Lineweaver-Burk kinetics with D. radiodurans SOD KMapp value was smaller than pure SOD. The result showed that D. radiodurans SOD had higher enzyme-substrate affinity and specificity than pure SOD. It concluded that D. radiodurans SOD had a great potential as biological recognition component for antioxidant biosensor.
Abstract: Global temperature had increased by about 0.5oC over
the past century, increasing temperature leads to a loss or a decrease
of soil organic matter (SOM). Whereas soil organic matter in many
tropical soils is less stable than that of temperate soils, and it will be
easily affected by climate change. Therefore, conservation of soil
organic matter is urgent issue nowadays. This paper presents the
effect of different doses (5%, 15%) of Ca-type zeolite in conjunction
with organic manure, applied to soil samples from Philippines,
Paraguay and Japan, on the decomposition resistance of soil organic
matter under high temperature. Results showed that a remain or
slightly increase the C/N ratio of soil. There are an increase in
percent of humic acid (PQ) that extracted with Na4P2O7. A decrease
of percent of free humus (fH) after incubation was determined. A
larger the relative color intensity (RF) value and a lower the color
coefficient (6logK) value following increasing zeolite rates leading
to a higher degrees of humification. The increase in the aromatic
condensation of humic acid (HA) after incubation, as indicates by the
decrease of H/C and O/C ratios of HA. This finding indicates that the
use of zeolite could be beneficial with respect to SOM conservation
under global warming condition.
Abstract: This study investigated the effect of oxygen and
micro-cracking on the flotation of low grade nickel sulphide ore. The
ore treated contained serpentine minerals which have a history of
being difficult to process efficiently. The use of oxygen as a bubbling
gas has been noted to be effective because it increases the pulp
potential. The desired effect of micro cracking the ore is that the
nickel sulphide minerals will become activated and this activation
will render these minerals more susceptible to react with potassium
amyl xanthate collectors, resulting in a higher recovery of nickel and
hinder the recovery of other undesired minerals contained in the ore.
Higher nickel recoveries were obtained when pure oxygen was used
as a bubbling gas rather than the conventional air. Microwave
cracking favored the recovery of nickel.
Abstract: In Data mining, Fuzzy clustering algorithms have
demonstrated advantage over crisp clustering algorithms in dealing
with the challenges posed by large collections of vague and uncertain
natural data. This paper reviews concept of fuzzy logic and fuzzy
clustering. The classical fuzzy c-means algorithm is presented and its
limitations are highlighted. Based on the study of the fuzzy c-means
algorithm and its extensions, we propose a modification to the cmeans
algorithm to overcome the limitations of it in calculating the
new cluster centers and in finding the membership values with
natural data. The efficiency of the new modified method is
demonstrated on real data collected for Bhutan-s Gross National
Happiness (GNH) program.
Abstract: Axial Flux Permanent Magnet (AFPM) Machines require effective cooling due to their high power density. The detrimental effects of overheating such as degradation of the insulation materials, magnets demagnetization, and increase of Joule losses are well known. This paper describes the CFD simulations performed on a test rig model of an air cooled Axial Flux Permanent Magnet (AFPM) generator built at Durham University to identify the temperatures and heat transfer coefficient on the stator. The Reynolds Averaged Navier-Stokes and the Energy equations are solved and the flow pattern and heat transfer developing inside the machine are described. The Nusselt number on the stator surfaces has been found. The dependency of the heat transfer on the flow field is described temperature field obtained. Tests on an experimental are undergoing in order to validate the CFD results.
Abstract: Boron minerals are very useful for various industrial
activities, such as glass industry and detergent industry, due to its
mechanical and chemical properties. During the production of boron
compounds, many of these are introduced into the environment in the
form of waste. Boron is also an important micro nutrient for the
plants to vegetate but if it exists in high concentrations, it could have
toxic effects. The maximum boron level in drinking water for human
health is given as 0.3 mg/L in World Health Organization (WHO)
standards. The toxic effects of boron should be noted especially for
dry regions, thus, in recent years, increasing attention has been paid
to remove the boron from waste waters. In this study, boron removal
is implemented by ion exchange process using Amberlite IRA-743
resin. Amberlite IRA-743 resin is a boron specific resin and it
belongs to the polymerizate sorbent group within the aminopolyol
functional group. Batch studies were performed to investigate the
effects of various experimental parameters, such as adsorbent dose,
initial concentration and pH, on the removal of boron. It is found
that, when the adsorbent dose increases removal of boron from the
liquid phase increases. However, an increase in the initial
concentration decreases the removal of boron. The effective pH
values for removal of boron are determined between 8.5 and 9.
Equilibrium isotherms were also analyzed by Langmuir and
Freundlich isotherm models. The Langmuir isotherm is obeyed better
than the Freundlich isotherm.
Abstract: In the process of polyethylene extrusion polymer
material similar to powder or granule is under compression, melting
and transmission operation and on base of special form, extrudate has
been produced. Twin-screw extruders are applicable in industries
because of their high capacity. The powder mixing with chemical
additives and melting with thermal and mechanical energy in three
zones (feed, compression and metering zone) and because of gear
pump and screw's pressure, converting to final product in latest plate.
Extruders with twin-screw and short distance between screws are
better than other types because of their high capacity and good
thermal and mechanical stress.
In this paper, process of polyethylene extrusion and various tapes
of extruders are studied. It is necessary to have an exact control on
process to producing high quality products with safe operation and
optimum energy consumption.
The granule size is depending on granulator motor speed. Results
show at constant feed rate a decrease in granule size was found whit
Increase in motor speed. Relationships between HDPE feed rate and
speed of granulator motor, main motor and gear pump are calculated
following as:
x = HDPE feed flow rate, yM = Main motor speed
yM = (-3.6076e-3) x^4+ (0.24597) x^3+ (-5.49003) x^2+ (64.22092)
x+61.66786 (1)
x = HDPE feed flow rate, yG = Gear pump speed
yG = (-2.4996e-3) x^4+ (0.18018) x^3+ (-4.22794) x^2+ (48.45536)
x+18.78880 (2)
x = HDPE feed flow rate, y = Granulator motor speed
10th Degree Polynomial Fit: y = a+bx+cx^2+dx^3... (3)
a = 1.2751, b = 282.4655, c = -165.2098,
d = 48.3106, e = -8.18715, f = 0.84997
g = -0.056094, h = 0.002358, i = -6.11816e-5
j = 8.919726e-7, k = -5.59050e-9
Abstract: In countries with hot climates, air-conditioning forms
a large proportion of annual peak electrical demand, requiring
expansion of power plants to meet the peak demand, which goes
unused most of the time. Use of well-designed cool storage can offset
the peak demand to a large extent. In this study, an air conditioning
system with naturally stratified storage tank was designed,
constructed and tested. A new type of diffuser was designed and used
in this study. Factors that influence the performance of chilled water
storage tanks were investigated. The results indicated that stratified
storage tank consistently stratified well without any physical barrier.
Investigation also showed that storage efficiency decreased with
increasing flow rate due to increased mixing of warm and chilled
water. Diffuser design and layout primarily affected the mixing near
the inlet diffuser and the extent of this mixing had primary influence
on the shape of the thermocline. The heat conduction through tank
walls and through the thermocline caused widening of mixed volume.
Thermal efficiency of stratified storage tanks was as high as 90
percent, which indicates that stratified tanks can effectively be used
as a load management technique.
Abstract: This paper presents and discusses the numerical simulations of transient laminar natural convection cooling of high Prandtl number fluids in cubical cavities, in which the six walls of the cavity are subjected to a step change in temperature. The effect of the fluid Prandtl number on the heat transfer coefficient is studied for three different fluids (Golden Syrup, Glycerin and Glycerin-water solution 50%). The simulations are performed at two different Rayleigh numbers (5·106 and 5·107) and six different Prandtl numbers (3 · 105 ≥Pr≥ 50). Heat conduction through the cavity glass walls is also considered. The propsed correlations of the averaged heat transfer coefficient (N u) showed that it is dependant on the initial Ra and almost independent on P r. The instantaneous flow patterns, temperature contours and time evolution of volume averaged temperature and heat transfer coefficient are presented and analyzed.
Abstract: This paper describes the design and modeling
procedure of a novel 5-phase segment type switched reluctance motor
(ST-SRM) under simultaneous two-phase (bipolar) excitation of
windings. The rotor cores of ST-SRM are embedded in an aluminum
block as well as to improve the performance characteristics. The
magnetic circuit of the produced ST-SRM is constructed so that the
magnetic flux paths are short and exclusive to each phase, thereby
minimizing the commutation switching and eddy current losses in the
laminations. The design and simulation principles presented apply
primarily to conventional SRM and ST-SRM. It is proved that the
novel 5-phase switched reluctance motor under two-phase excitation
is superior among the criteria used in comparison. The purposed
model is particularly well suited for high torque and weight
constrained applications such as automobiles, aerospace and military
applications.
Abstract: Modes of occurrence of Pb, As, Cr, Co, Cu, and Ni in bituminous coal and lignite were determined by means of sequential extraction using NH4OAc, HCl, HF and HNO3 extraction solutions. Elemental affinities obtained were then evaluated in relation to volatility of these elements during the combustion of these coals in two circulating fluidised-bed power stations. It was found out that higher percentage of the elements bound in silicates brought about lower volatility, while higher elemental proportion with monosulphides association (or bound as exchangeable ion) resulted in higher volatility. The only exception was the behavior of arsenic, whose volatility depended on amount of limestone added during the combustion process (as desulphurisation additive) rather than to its association in coal.