Abstract: One of the most challenges for hard surface cleaning product is to get rid of soap scum, a filmy sticky layer in the bathroom. The deposits of soap scum can be removed by using a proper surfactant solution with chelating agent. Unfortunately, the conventional chelating agent, ethylenediamine tetraacetic acid (EDTA), has low biodegradability, which can be tolerance in water resources and harmful to aquatic animal and microorganism. In this study, two biodegradable chelating agents, ethylenediamine disuccinic acid (EDDS) and glutamic acid diacetic acid (GLDA) were introduced as a replacement of EDTA. The result shows that using GLDA with amphoteric surfactant gave the highest equilibrium solubility of soap scum.
Abstract: Service trade is an important force of influencing economic development. A review on the related literatures is done firstly. Then through the construction of a Diamond Model, the main factors which influence the competitiveness of Chinese service trade are determined. With three competitiveness indexes served as the reference series respectively, the influencing factors served as the comparable series, three grey incidence models are then built up to conduct an empirical analysis on the main factors influencing the competitiveness of service trade after China entering WTO. The result indicates that urbanization level, open degree of service industry and foreign direct investment have larger impacts on Chinese service trade competitiveness, followed in turn by GDP in service industry and human capital, while commodity trade has the minimum impact. Further discussion provides train of thought for the upgrade of Chinese service trade competitiveness.
Abstract: Studying alternative raw materials for biodiesel production is of major importance. The use of mixtures with incorporation of wastes is an environmental friendly alternative and might reduce biodiesel production costs. The objective of the present work was: (i) to study biodiesel production using waste frying oil mixed with pork lard and (ii) to understand how mixture composition influences biodiesel quality. Biodiesel was produced by transesterification and quality was evaluated through determination of several parameters according to EN 14214. The weight fraction of lard in the mixture varied from 0 to 1 in 0.2 intervals. Biodiesel production yields varied from 81.7 to 88.0 (wt%), the lowest yields being the ones obtained using waste frying oil and lard alone as raw materials. The obtained products fulfilled most of the determined quality specifications according to European biodiesel quality standard EN 14214. Minimum purity (96.5 wt%) was closely obtained when waste frying oil was used alone and when 0.2% of lard was incorporated in the raw material (96.3 wt%); however, it ranged from 93.9 to 96.3 (wt%) being always close to the limit. From the evaluation of the influence of mixture composition in biodiesel quality, it was possible to establish a model to be used for predicting some parameters of biodiesel resulting from mixtures of waste frying oil with lard when different lard contents are used.
Abstract: The development of biomimetic micro-aerial-vehicles
(MAVs) with flapping wings is the future trend in military/domestic
field. The successful flight of MAVs is strongly related to the
understanding of unsteady aerodynamic performance of low Reynolds
number airfoils under dynamic flapping motion. This study explored
the effects of flapping frequency, stroke amplitude, and the inclined
angle of stroke plane on lift force and thrust force of a bio-inspiration
corrugated airfoil with 33 full factorial design of experiment and
ANOVA analysis. Unsteady vorticity flows over a corrugated thin
airfoil executing flapping motion are computed with time-dependent
two-dimensional laminar incompressible Reynolds-averaged
Navier-Stokes equations with the conformal hybrid mesh. The tested
freestream Reynolds number based on the chord length of airfoil as
characteristic length is fixed of 103. The dynamic mesh technique is
applied to model the flapping motion of a corrugated airfoil. Instant
vorticity contours over a complete flapping cycle clearly reveals the
flow mechanisms for lift force generation are dynamic stall, rotational
circulation, and wake capture. The thrust force is produced as the
leading edge vortex shedding from the trailing edge of airfoil to form a
reverse von Karman vortex. Results also indicated that the inclined
angle is the most significant factor on both the lift force and thrust
force. There are strong interactions between tested factors which mean
an optimization study on parameters should be conducted in further
runs.
Abstract: Home Automation is a field that, among other
subjects, is concerned with the comfort, security and energy
requirements of private homes. The configuration of automatic
functions in this type of houses is not always simple to its inhabitants
requiring the initial setup and regular adjustments. In this work, the
ubiquitous computing system vision is used, where the users- action
patterns are captured, recorded and used to create the contextawareness
that allows the self-configuration of the home automation
system. The system will try to free the users from setup adjustments
as the home tries to adapt to its inhabitants- real habits. In this paper
it is described a completely automated process to determine the light
state and act on them, taking in account the users- daily habits.
Artificial Neural Network (ANN) is used as a pattern recognition
method, classifying for each moment the light state. The work
presented uses data from a real house where a family is actually
living.
Abstract: Aim of this study is to evaluate a new three-equation turbulence model applied to flow and heat transfer through a pipe. Uncertainty is approximated by comparing with published direct numerical simulation results for fully-developed flow. Error in the mean axial velocity, temperature, friction, and heat transfer is found to be negligible.
Abstract: The aim of this paper is to experimentally discover the workability coefficient of the Inconel 718 material by using a slide turning machining. Two different types of cutting inserts, one made of carbide and the other one made of ceramic, are being used. The purpose is to compare measured results and recommend the appropriate materials and cutting parameters for a machining of the Inconel 718. Furthermore, the durability of inserts with the chosen wear criterion is being compared for different cutting speeds. Machinability of these materials is a crucial characteristic as it allows us to shorten the technological cycle time and increase the machining productivity. And this is of great importance from an economic point of view.
Abstract: The increasing development of wireless networks and
the widespread popularity of handheld devices such as Personal
Digital Assistants (PDAs), mobile phones and wireless tablets
represents an incredible opportunity to enable mobile devices as a
universal payment method, involving daily financial transactions.
Unfortunately, some issues hampering the widespread acceptance of
mobile payment such as accountability properties, privacy protection,
limitation of wireless network and mobile device. Recently, many
public-key cryptography based mobile payment protocol have been
proposed. However, limited capabilities of mobile devices and
wireless networks make these protocols are unsuitable for mobile
network. Moreover, these protocols were designed to preserve
traditional flow of payment data, which is vulnerable to attack and
increase the user-s risk. In this paper, we propose a private mobile
payment protocol which based on client centric model and by
employing symmetric key operations. The proposed mobile payment
protocol not only minimizes the computational operations and
communication passes between the engaging parties, but also
achieves a completely privacy protection for the payer. The future
work will concentrate on improving the verification solution to
support mobile user authentication and authorization for mobile
payment transactions.
Abstract: A first intermediate roll of Sendzirmir mills was failure
by surface spalling during operation. After analyzing by visual, stereo
microscope, optical microscope, scanning electron microscope,
glow-discharged spectrometer and hardness test, respectively, the
results show that some voids and cracks existed on the contact surface
as well as subsurface. Further examination verified inadequate
hardness and inclusions were responsible for the failure of surface
spalling.
Abstract: The article deals with experimental and numerical
investigation of axi-symmetric subsonic air to air ejector with
diffuser adapted for boundary layer suction. The diffuser, which is
placed behind the mixing chamber of the ejector, has high divergence
angle and therefore low efficiency. To increase the efficiency, the
diffuser is equipped with slot enabling boundary layer suction. The
effect of boundary layer suction on flow in ejector, static pressure
distribution on the mixing chamber wall and characteristic were
measured and studied numerically. Both diffuser and ejector
efficiency were evaluated. The diffuser efficiency was increased,
however, the efficiency of ejector itself remained low.
Abstract: The daily increase of organic waste materials resulting
from different activities in the country is one of the main factors for
the pollution of environment. Today, with regard to the low level of
the output of using traditional methods, the high cost of disposal
waste materials and environmental pollutions, the use of modern
methods such as anaerobic digestion for the production of biogas has
been prevailing. The collected biogas from the process of anaerobic
digestion, as a renewable energy source similar to natural gas but
with a less methane and heating value is usable. Today, with the help
of technologies of filtration and proper preparation, access to biogas
with features fully similar to natural gas has become possible. At
present biogas is one of the main sources of supplying electrical and
thermal energy and also an appropriate option to be used in four
stroke engine, diesel engine, sterling engine, gas turbine, gas micro
turbine and fuel cell to produce electricity. The use of biogas for
different reasons which returns to socio-economic and environmental
advantages has been noticed in CHP for the production of energy in
the world. The production of biogas from the technology of anaerobic
digestion and its application in CHP power plants in Iran can not only
supply part of the energy demands in the country, but it can
materialize moving in line with the sustainable development. In this
article, the necessity of the development of CHP plants with biogas
fuels in the country will be dealt based on studies performed from the
economic, environmental and social aspects. Also to prove the
importance of the establishment of these kinds of power plants from
the economic point of view, necessary calculations has been done as
a case study for a CHP power plant with a biogas fuel.
Abstract: Image interpolation is a common problem in imaging applications. However, most interpolation algorithms in existence suffer visually to some extent the effects of blurred edges and jagged artifacts in the image. This paper presents an adaptive feature preserving bidirectional flow process, where an inverse diffusion is performed to enhance edges along the normal directions to the isophote lines (edges), while a normal diffusion is done to remove artifacts (''jaggies'') along the tangent directions. In order to preserve image features such as edges, angles and textures, the nonlinear diffusion coefficients are locally adjusted according to the first and second order directional derivatives of the image. Experimental results on synthetic images and nature images demonstrate that our interpolation algorithm substantially improves the subjective quality of the interpolated images over conventional interpolations.
Abstract: This study was aimed to determine seasonal variations
of leaf nutrient concentrations to define nutrient needs related to
growing period and to compare irrigation programs in terms of
nutrient uptake. In this study,'Starkrimson Delicious' variety grafted
onto seedling rootstock was used during 2009-2010 growing seasons.
The study was conducted at E─ƒirdir Fruit Growing Research Station.
Leaf samples were taken in five different sample seasons (May, June,
July, August and September). Four different pan coefficients (0.50,
0.75, 1.0, 1.25) were applied during drip irrigation treatments in 7
days irrigation interval. Leaf K, Mg, Ca, P, Fe, Zn, Mn and Cu
concentrations were determined.
The results showed that among the seasonal changes, the highest
concentrations of K, Mg, P and Mn in leaves were recorded in May,
followed by a decrease in the other months, while in contrast Ca and
Fe showed the lowest concentration in May.
Results of the study demonstrate that among irrigation programs K
and Cu concentration in plants was significantly influenced. Cu
concentrations decreased with seasonal variations and different
irrigation programs. Thus, nutrient needs of 'Starkrimson Delicious'apple trees at different growth stages should be taken into
consideration before making effective fertilization program.
Abstract: Fractal analyses of successive event of explosion
earthquake and harmonic tremor recorded at Semeru volcano were
carried out to investigate the dynamical system regarding to their
generating mechanism. The explosive eruptions accompanied by
explosion earthquakes and following volcanic tremor which are
generated by continuous emission of volcanic ash. The fractal
dimension of successive event of explosion and harmonic tremor was
estimated by Critical Exponent Method (CEM). It was found that the
method yield a higher fractal dimension of explosion earthquakes and
gradually decrease during the occurrence of harmonic tremor, and can
be considerably as correlated complexity of the source mechanism
from the variance of fractal dimension.
Abstract: Imitation learning is considered to be an effective way of teaching humanoid robots and action recognition is the key step to imitation learning. In this paper an online algorithm to recognize
parametric actions with object context is presented. Objects are key instruments in understanding an action when there is uncertainty.
Ambiguities arising in similar actions can be resolved with objectn context. We classify actions according to the changes they make to
the object space. Actions that produce the same state change in the object movement space are classified to belong to the same class. This allow us to define several classes of actions where members of
each class are connected with a semantic interpretation.
Abstract: Determining reasonable fees is the main objective of designing the cost estimation and payment systems for consultant contracts. However, project clients utilize different cost estimation and payment systems because of their varying views on the reasonableness of consultant fees. This study reviews the cost estimation and payment systems of consultant contracts for five countries, including the US (Washington State Department of Transportation), Japan (Ministry of Land, Infrastructure, Transport and Tourism), China (Engineering Design Charging Standard) and UK (Her Majesty's Treasure). Specifically, this work investigates the budgeting process, contractor selection method, contractual price negotiation process, cost review, and cost-control concept of the systems used in these countries. The main finding indicates that that project client-s view on whether the fee is high will affect the way he controls it. In the US, the fee is commonly considered to be high. As a result, stringent auditing system (low flexibility given to the consultant) is then applied. In the UK, the fee is viewed to be low by comparing it to the total life-cycle project cost. Thus, a system that has high flexibility in budgeting and cost reviewing is given to the consultant. In terms of the flexibility allowed for the consultant, the systems applied in Japan and China fall between those of the US and UK. Both the US and UK systems are helpful in determining a reasonable fee. However, in the US system, rigid auditing standards must be established and additional cost-audit manpower is required. In the UK system, sufficient historical cost data should be needed to evaluate the reasonableness of the consultant-s proposed fee
Abstract: Materials added to the matrix help improving operating properties of a composite. This experimental study has targeted to investigate this aim where Silicon Oxide particles were added to glass fibre and epoxy resin at an amount of 15% to the main material to obtain a sort of new composite material. Erosive wear behavior of epoxy-resin dipped composite materials reinforced with glass fibre and Silicon Oxide under three different impingement angles (30°, 60° and 90°), three different impact velocities (23, 34 and 53 m/s), two different angular Aluminum abrasive particle sizes (approximately 200 and 400 μm) and the fibre orientation of 45° (45/-45) were investigated. In the test results, erosion rates were obtained as functions of impingement angles, impact velocities, particle sizes and fibre orientation. Moreover, materials with addition of Silicon Oxide filler material exhibited lower wear as compared to neat materials with no added filler material. In addition, SEM views showing worn out surfaces of the test specimens were scrutinized.
Abstract: The abnormal increase in the number of applications available for download in Android markets is a good indication that they are being reused. However, little is known about their real reusability potential. A considerable amount of these applications is reported as having a poor quality or being malicious. Hence, in this paper, an approach to measure the reusability potential of classes in Android applications is proposed. The approach is not meant specifically for this particular type of applications. Rather, it is intended for Object-Oriented (OO) software systems in general and aims also to provide means to discard the classes of low quality and defect prone applications from being reused directly through inheritance and instantiation. An empirical investigation is conducted to measure and rank the reusability potential of the classes of randomly selected Android applications. The results obtained are thoroughly analyzed in order to understand the extent of this potential and the factors influencing it.
Abstract: By utilizing the system of the recurrence equations, containing two parameters, the dynamics of two antagonistically interconnected populations is studied. The following areas of the system behavior are detected: the area of the stable solutions, the area of cyclic solutions occurrence, the area of the accidental change of trajectories of solutions, and the area of chaos and fractal phenomena. The new two-dimensional diagram of the dynamics of the solutions change (the fractal cabbage) has been obtained. In the cross-section of this diagram for one of the equations the well-known Feigenbaum tree of doubling has been noted.Keywordsbifurcation, chaos, dynamics of populations, fractals
Abstract: This paper investigates the problem of automated defect
detection for textile fabrics and proposes a new optimal filter design
method to solve this problem. Gabor Wavelet Network (GWN) is
chosen as the major technique to extract the texture features from
textile fabrics. Based on the features extracted, an optimal Gabor filter
can be designed. In view of this optimal filter, a new semi-supervised
defect detection scheme is proposed, which consists of one real-valued
Gabor filter and one smoothing filter. The performance of the scheme
is evaluated by using an offline test database with 78 homogeneous
textile images. The test results exhibit accurate defect detection with
low false alarm, thus showing the effectiveness and robustness of the
proposed scheme. To evaluate the detection scheme comprehensively,
a prototyped detection system is developed to conduct a real time test.
The experiment results obtained confirm the efficiency and
effectiveness of the proposed detection scheme.