Abstract: In this report we have discussed the theoretical aspects
of the flow transformation, occurring through a series of bifurcations.
The parameters and their continuous diversion, the intermittent bursts
in the transition zone, variation of velocity and pressure with time,
effect of roughness in turbulent zone, and changes in friction factor
and head loss coefficient as a function of Reynolds number for a
transverse flow across a cylinder have been discussed. An analysis of
the variation in the wake length with Reynolds number was done in
FORTRAN.
Abstract: High Peak to Average Power Ratio (PAPR) of the
transmitted signal is a serious problem in multicarrier systems (MC),
such as Orthogonal Frequency Division Multiplexing (OFDM), or in
Multi-Carrier Code Division Multiple Access (MC-CDMA) systems,
due to large number of subcarriers. This effect is possible reduce with
some PAPR reduction techniques. Spreading sequences at the
presence of Saleh and Rapp models of high power amplifier (HPA)
have big influence on the behavior of system. In this paper we
investigate the bit-error-rate (BER) performance of MC-CDMA
systems. Basically we can see from simulations that the MC-CDMA
system with Iterative algorithm can be providing significantly better
results than the MC-CDMA system. The results of our analyses are
verified via simulation.
Abstract: Iris codes contain bits with different entropy. This
work investigates different strategies to reduce the size of iris
code templates with the aim of reducing storage requirements and
computational demand in the matching process. Besides simple subsampling
schemes, also a binary multi-resolution representation as
used in the JBIG hierarchical coding mode is assessed. We find that
iris code template size can be reduced significantly while maintaining
recognition accuracy. Besides, we propose a two-stage identification
approach, using small-sized iris code templates in a pre-selection
stage, and full resolution templates for final identification, which
shows promising recognition behaviour.
Abstract: The adsorption efficiency of fired clayey pellets of 5
and 8 mm diameter size for Cu(II) and Zn(II) ion removal from a
waste printing developer was studied. In order to investigate the
influence of contact time, adsorbent mass and pellet size on the
adsorption efficiency the batch mode was carried out. Faster uptake
of copper ion was obtained with the fired clay pellets of 5 mm
diameter size within 30 minutes. The pellets of 8 mm diameter size
showed the higher equilibrium time (60 to 75 minutes) for copper and
zinc ion. The results pointed out that adsorption efficiency increases
with the increase of adsorbent mass. The maximal efficiency is
different for Cu(II) and Zn(II) ion due to the pellet size. Therefore,
the fired clay pellets of 5 mm diameter size present an effective
adsorbent for Cu(II) ion removal (adsorption efficiency is 63.6%),
whereas the fired clay pellets of 8 mm diameter size are the best
alternative for Zn(II) ion removal (adsorption efficiency is 92.8%)
from a waste printing developer.
Abstract: Background: With the perceived pain and poor
function experienced following knee arthroplasty, patients usually
feel un-satisfied. Yet, a controversy still persists on the appropriate
operative technique that doesn’t affect proprioception much.
Purpose: This study compared the effects of Cruciate Retaining
(CR) and Posterior Stabilized (PS) total knee arthroplasty (TKA on
dynamic balance, pain and functional performance following
rehabilitation.
Methods: Thirty patients with CRTKA (group I), thirty with
PSTKA (group II) and fifteen indicated for arthroplasty but weren’t
operated on yet (group III) participated in the study. The mean age
was 54.53±3.44, 55.13±3.48 and 55.33±2.32 years and BMI
35.7±3.03, 35.7±1.99 and 35.73±1.03 kg/m2 for groups I, II and III
respectively. The Berg Balance Scale (BBS), WOMAC pain subscale
and Timed Up-and-Go (TUG) and Stair-Climbing (SC) tests were
used for assessment. Assessments were conducted four weeks preand
post-operatively, three, six and twelve months post-operatively
with the control group being assessed at the same time intervals. The
post-operative rehabilitation involved hospitalization (1st week),
home-based (2nd-4th weeks), and outpatient clinic (5th-12th weeks)
programs, follow-up to all groups for twelve months.
Results: The Mixed design MANOVA revealed that group I had
significantly lower pain scores and SC time compared with group II
three, six and twelve months post-operatively. Moreover, the BBS
scores increased significantly and the pain scores and TUG and SC
time decreased significantly six months post-operatively compared
with four weeks pre- and post-operatively and three months postoperatively
in groups I and II with the opposite being true four weeks
post-operatively. But no significant differences in BBS scores, pain
scores and TUG and SC time between six and twelve months postoperatively
in groups I and II.
Interpretation/Conclusion: CRTKA is preferable to PSTKA,
possibly due to the preserved human proprioceptors in the un-excised
PCL.
Abstract: Kazakhstan is currently one of the dynamically
developing states in its region. The stable growth in all sectors of the
economy leads to a corresponding increase in energy consumption.
Thus country consumes significant amount of energy due to the high
level of industrialisation and the presence of energy-intensive
manufacturing such as mining and metallurgy which in turn leads to
low energy efficiency. With allowance for this the Government has
set several priorities to adopt a transition of Republic of Kazakhstan
to a “green economy”. This article provides an overview of
Kazakhstan’s energy efficiency situation in for the period of 1991-
2014. First, the dynamics of production and consumption of
conventional energy resources are given. Second, the potential of
renewable energy sources is summarised followed by the description
of GHG emissions trends in the country. Third, Kazakhstan’ national
initiatives, policies and locally implemented projects in the field of
energy efficiency are described.
Abstract: In this study, composites were fabricated from oil
palm empty fruit bunch fiber and poly(lactic) acid by extrusion
followed by injection moulding. Surface of the fiber was pre-treated
by ultrasound in an alkali medium and treatment efficiency was
investigated by scanning electron microscopy (SEM) analysis and
Fourier transforms infrared spectrometer (FTIR). Effect of fiber
treatment on composite was characterized by tensile strength (TS),
tensile modulus (TM) and impact strength (IS). Furthermore,
biostrong impact modifier was incorporated into the treated fiber
composite to improve its impact properties. Mechanical testing
showed an improvement of up to 23.5% and 33.6% respectively for
TS and TM of treated fiber composite above untreated fiber
composite. On the other hand incorporation of impact modifier led to
enhancement of about 20% above the initial IS of the treated fiber
composite.
Abstract: Parameters of flow are calculated in vaneless diffusers
with relative width 0,014–0,10. Inlet angles of flow and similarity
criteria were varied. There is information on flow separation,
boundary layer development, configuration of streamlines.
Polytrophic efficiency, loss coefficient and recovery coefficient are
used to compare effectiveness of diffusers. The sample of
optimization of narrow diffuser with conical walls is presented. Three
wide diffusers with narrowing walls are compared. The work is made
in the R&D laboratory “Gas dynamics of turbo machines” of the TU
SPb.
Abstract: In this paper we consider the rule reduct generation
problem. Rule Reduct Generation (RG) and Modified Rule
Generation (MRG) algorithms, that are used to solve this problem,
are well-known. Alternative to these algorithms, we develop Pruning
Rule Generation (PRG) algorithm. We compare the PRG algorithm
with RG and MRG.
Abstract: Universal modeling method well proven for industrial
compressors was applied for design of the high flow rate supersonic
stage. Results were checked by ANSYS CFX and NUMECA Fine
Turbo calculations. The impeller appeared to be very effective at
transonic flow velocities. Stator elements efficiency is acceptable at
design Mach numbers too. Their loss coefficient versus inlet flow
angle performances correlates well with Universal modeling
prediction. The impeller demonstrates ability of satisfactory operation
at design flow rate. Supersonic flow behavior in the impeller inducer
at the shroud blade to blade surface Φ des deserves additional study.
Abstract: There is an evident trend to elevate pressure ratio of a
single stage of a turbo compressors - axial compressors in particular.
Whilst there was an opinion recently that a pressure ratio 1,9 was a
reasonable limit, later appeared information on successful modeling
tested of stages with pressure ratio up to 2,8. The authors recon that
lack of information on high pressure stages makes actual a study of
rational choice of design parameters before high supersonic flow
problems solving. The computer program of an engineering type was
developed. Below is presented a sample of its application to study
possible parameters of the impeller of the stage with pressure ratio
3,0. Influence of two main design parameters on expected efficiency,
periphery blade speed and flow structure is demonstrated. The results
had lead to choose a variant for further analysis and improvement by
CFD methods.
Abstract: Many organizations bring e-Learning to use as a tool
in their training and human development department. It is getting
more popular because it is easy to access to get knowledge all the
time and also it provides a rich content, which can develop the
employees’ skill efficiently. This study is focused on the factors that
affect using e-Learning efficiently, so it will make job satisfaction
increasing. The questionnaires were sent to employees in large
commercial banks, which use e-Learning located in Bangkok, the
results from multiple linear regression analysis showed that
employee’s characteristics, characteristics of e-Learning, learning and
growth have influence on job satisfaction.
Abstract: The continuous decline of petroleum and natural gas
reserves and non linear rise of oil price has brought about a
realisation of the need for a change in our perpetual dependence on
the fossil fuel. A day to day increased consumption of crude and
petroleum products has made a considerable impact on our foreign
exchange reserves. Hence, an alternate resource for the conversion of
energy (both liquid and gas) is essential for the substitution of
conventional fuels. Biomass is the alternate solution for the present
scenario. Biomass can be converted into both liquid as well as
gaseous fuels and other feedstocks for the industries.
Abstract: This paper introduces novel approaches to partitioning
and mapping in terms of model-based embedded multicore system
engineering and further discusses benefits, industrial relevance and
features in common with existing approaches. In order to assess
and evaluate results, both approaches have been applied to a real
industrial application as well as to various prototypical demonstrative
applications, that have been developed and implemented for
different purposes. Evaluations show, that such applications improve
significantly according to performance, energy efficiency, meeting
timing constraints and covering maintaining issues by using
the AMALTHEA platform and the implemented approaches.
Furthermore, the model-based design provides an open, expandable,
platform independent and scalable exchange format between
OEMs, suppliers and developers on different levels. Our proposed
mechanisms provide meaningful multicore system utilization since
load balancing by means of partitioning and mapping is effectively
performed with regard to the modeled systems including hardware,
software, operating system, scheduling, constraints, configuration and
more data.
Abstract: Member States shall establish zones and
agglomerations throughout their territory to assess and manage air
quality in order to comply with European directives.
In Italy decree 155/2010, transposing Directive 2008/50/EC on
ambient air quality and cleaner air for Europe, merged into a single
act the previous provisions on ambient air quality assessment and
management, including those resulting from the implementation of
Directive 2004/107/EC relating to arsenic, cadmium, nickel, mercury
and polycyclic aromatic hydrocarbons in ambient air.
Decree 155/2010 introduced stricter rules for identifying zones on
the basis of the characteristics of the territory in spite of considering
pollution levels, as it was in the past. The implementation of such
new criteria has reduced the great variability of the previous zoning,
leading to a significant reduction of the total number of zones and to
a complete and uniform ambient air quality assessment and
management throughout the Country.
The present document is related to the new zones definition in
Italy according to Decree 155/2010. In particular the paper contains
the description and the analysis of the outcome of zoning and
classification.
Abstract: The number of Ground Motion Prediction Equations
(GMPEs) used for predicting peak ground acceleration (PGA) and
the number of earthquake recordings that have been used for fitting
these equations has increased in the past decades. The current PF-L
database contains 3550 recordings. Since the GMPEs frequently
model the peak ground acceleration the goal of the present study was
to refit a selection of 44 of the existing equation models for PGA in
light of the latest data. The algorithm Levenberg-Marquardt was used
for fitting the coefficients of the equations and the results are
evaluated both quantitatively by presenting the root mean squared
error (RMSE) and qualitatively by drawing graphs of the five best
fitted equations. The RMSE was found to be as low as 0.08 for the
best equation models. The newly estimated coefficients vary from the
values published in the original works.
Abstract: Company managers are always looking for more and
more opportunities to succeed in today's fiercely competitive market.
To maintain your place among the successful companies on the
market today or to come up with a revolutionary business idea is
much more difficult than before. Each new or improved method, tool,
or approach that can improve the functioning of business processes or
even of the entire system is worth checking and verification. The use
of simulation in the design of manufacturing systems and their
management in practice is one of the ways without increased risk,
which makes it possible to find the optimal parameters of
manufacturing processes and systems. The paper presents an example
of use of simulation for solution of the bottleneck problem in the
concrete company.
Abstract: Conventional educational practices, do not offer all
the required skills for teachers to successfully survive in today’s
workplace. Due to poor professional training, a big gap exists across
the curriculum plan and the teacher practices in the classroom. As
such, raising the quality of teaching through ICT-enabled training and
professional development of teachers should be an urgent priority.
‘Mobile Learning’, in that vein, is an increasingly growing field of
educational research and practice across schools and work places. In
this paper, we propose a novel Mobile learning system that allows the
users to learn through an intelligent mobile learning in cooperatively
every-time and every-where. The system will reduce the training cost
and increase consistency, efficiency, and data reliability. To establish
that our system will display neither functional nor performance
failure, the evaluation strategy is based on formal observation of
users interacting with system followed by questionnaires and
structured interviews.
Abstract: Job Scheduling plays an important role for efficient
utilization of grid resources available across different domains and
geographical zones. Scheduling of jobs is challenging and NPcomplete.
Evolutionary / Swarm Intelligence algorithms have been
extensively used to address the NP problem in grid scheduling.
Artificial Bee Colony (ABC) has been proposed for optimization
problems based on foraging behaviour of bees. This work proposes a
modified ABC algorithm, Cluster Heterogeneous Earliest First Min-
Min Artificial Bee Colony (CHMM-ABC), to optimally schedule
jobs for the available resources. The proposed model utilizes a novel
Heterogeneous Earliest Finish Time (HEFT) Heuristic Algorithm
along with Min-Min algorithm to identify the initial food source.
Simulation results show the performance improvement of the
proposed algorithm over other swarm intelligence techniques.
Abstract: In this paper, the electromagnetic shielding
characteristics of an up-to-date typical carbon filler material, carbon
fiber used with a metal mesh were investigated. Carbon fiber
12k-prepregs, where carbon fibers were impregnated with epoxy, were
laminated with wire meshes, vacuum bag-molded and hardened to
manufacture hybrid-type specimens, with which an electromagnetic
shield test was performed in accordance with ASTM D4935-10,
through which was known as the most excellent reproducibility is
obtainable among electromagnetic shield tests. In addition, glass fiber
prepregs whose electromagnetic shielding effect were known as
insignificant were laminated and formed with wire meshes to verify
the validity of the electromagnetic shield effect of wire meshes in
order to confirm the electromagnetic shielding effect of metal meshes
corresponding existing carbon fiber 12k-prepregs. By grafting carbon
fibers, on which studies are being actively underway in the
environmental aspects and electromagnetic shielding effect, with
hybrid-type wire meshes that were analysed through the tests, in this
study, the applicability and possibility are proposed.