Abstract: Torrefaction is one of waste to energy (WTE) technologies developing in Taiwan recently, which can reduce the moisture and impuritiesand increase the energy density of biowaste effectively.To understand the torrefaction characteristics of different biowaste and the influences of different torrefaction conditions, four typical biowaste were selected to carry out the torrefaction experiments. The physical and chemical properties of different biowaste prior to and after torrefaction were analyzed and compared. Experimental results show that the contents of elemental carbon and caloric value of the four biowaste were significantly increased after torrefaction. The increase of combustible and caloric value in bamboo was the greatest among the four biowaste. The caloric value of bamboo can be increased from 1526 kcal/kg to 6104 kcal/kg after 300oC and 1 hour torrefaction. The caloric valueof torrefied bamboo was almost four times as the original. The increase of elemental carbon content in wood was the greatest (from 41.03% to 75.24%), and the next was bamboo (from 47.07% to 74.63%). The major parameters which affected the caloric value of torrefied biowaste followed the sequence of biowaste kinds, torrefaction time, and torrefaction temperature. The optimal torrefaction conditions of the experiments were bamboo torrefied at 300oC for 3 hours, and the corresponding caloric value of torrefied bamboo was 5953 kcal/kg. This caloric value is similar to that of brown coal or bituminous coal.
Abstract: The centre of rotation of the hip joint is needed for an
accurate simulation of the joint performance in many applications
such as pre-operative planning simulation, human gait analysis, and
hip joint disorders. In human movement analysis, the hip joint center
can be estimated using a functional method based on the relative
motion of the femur to pelvis measured using reflective markers
attached to the skin surface. The principal source of errors in
estimation of hip joint centre location using functional methods is
soft tissue artefacts due to the relative motion between the markers
and bone. One of the main objectives in human movement analysis is
the assessment of soft tissue artefact as the accuracy of functional
methods depends upon it. Various studies have described the
movement of soft tissue artefact invasively, such as intra-cortical
pins, external fixators, percutaneous skeletal trackers, and Roentgen
photogrammetry. The goal of this study is to present a non-invasive
method to assess the displacements of the markers relative to the
underlying bone using optical motion capture data and tissue
thickness from ultrasound measurements during flexion, extension,
and abduction (all with knee extended) of the hip joint. Results show
that the artefact skin marker displacements are non-linear and larger
in areas closer to the hip joint. Also marker displacements are
dependent on the movement type and relatively larger in abduction
movement. The quantification of soft tissue artefacts can be used as a
basis for a correction procedure for hip joint kinematics.
Abstract: Human face has a fundamental role in the appearance
of individuals. So the importance of facial surgeries is undeniable.
Thus, there is a need for the appropriate and accurate facial skin
segmentation in order to extract different features. Since Fuzzy CMeans
(FCM) clustering algorithm doesn’t work appropriately for
noisy images and outliers, in this paper we exploit Possibilistic CMeans
(PCM) algorithm in order to segment the facial skin. For this
purpose, first, we convert facial images from RGB to YCbCr color
space. To evaluate performance of the proposed algorithm, the
database of Sahand University of Technology, Tabriz, Iran was used.
In order to have a better understanding from the proposed algorithm;
FCM and Expectation-Maximization (EM) algorithms are also used
for facial skin segmentation. The proposed method shows better
results than the other segmentation methods. Results include
misclassification error (0.032) and the region’s area error (0.045) for
the proposed algorithm.
Abstract: The paper is focused on testing of the poly(vinyl butyral) (PVB) layer which had the function of a CO2 insulating protection against concrete and mortar carbonation. The barrier efficiency of PVB was verified by the measurement of diffusion characteristics. Two different types of PVB were tested; original extruded PVB sheet and PVB sheet made from PVB dispersion which was obtained from recycled windshields. The work deals with the testing CO2 diffusion when polymer sheets were exposed to a CO2 atmosphere (10% v/v CO2) with 0% RH. The excellent barrier capability against CO2 permeability of original and also recycled types of PVB layers was observed. This application of PVB waste can bring advantageous use in civil engineering and significant environmental contribution.
Abstract: This paper discusses the performance of critical
trajectory method (CTrj) for power system transient stability analysis
under various loading settings and heavy fault condition. The method
obtains Controlling Unstable Equilibrium Point (CUEP) which is
essential for estimation of power system stability margins. The CUEP
is computed by applying the CTrjto the boundary controlling unstable
equilibrium point (BCU) method. The Proposed method computes a
trajectory on the stability boundary that starts from the exit point and
reaches CUEP under certain assumptions. The robustness and
effectiveness of the method are demonstrated via six power system
models and five loading conditions. As benchmark is used
conventional simulation method whereas the performance is compared
with and BCU Shadowing method.
Abstract: The design of multi stage deep drawing processes requires the evaluation of many process parameters such as the intermediate die geometry, the blank shape, the sheet thickness, the blank holder force, friction, lubrication etc..These process parameters have to be determined for the optimum forming conditions before the process design. In general sheet metal forming may involve stretching drawing or various combinations of these basic modes of deformation. It is important to determine the influence of the process variables in the design of sheet metal working process. Especially, the punch and die corner for deep drawing will affect the formability. At the same time the prediction of sheet metals springback after deep drawing is an important issue to solve for the control of manufacturing processes. Nowadays, the importance of this problem increases because of the use of steel sheeting with high stress and also aluminum alloys.
The aim of this paper is to give a better understanding of the springback and its effect in various sheet metals forming process such as expansion and restreint deep drawing in the cup drawing process, by varying radius die, lubricant for two commercially available materials e.g. galvanized steel and Aluminum sheet. To achieve these goals experiments were carried out and compared with other results. The original of our purpose consist on tests which are ensured by adapting a U-type stretching-bending device on a tensile testing machine, where we studied and quantified the variation of the springback.
Abstract: In this work, an experimental technique is applied
for the measurements of the vibrations and deformation of a test
transformer core. Since the grid voltage contains some higher
harmonics, in addition to a purely sinusoidal magnetisation of the
core the presence of third harmonic is also studied. The vibrations of
the transformer core for points as well as the surface scan of the leg
show more deformation in the corners of the leg than the middle of
the leg. The influence of the higher harmonic of the magnetisation
on the core deformation is also more significant in the corners of the
leg. The core deformation shape under a sinusoidal magnetisation
with a higher harmonic is more wavy and fluctuating than that under
a purely sinusoidal magnetisation.
Abstract: Membrane distillation is an emerging technology which has been used to produce freshwater and purify different types of aqueous mixtures. Qatar is an arid country where almost 100% of its freshwater demand is supplied through the energy-intensive thermal desalination process. The country’s need for water has reached an all-time high which stipulates finding an alternative way to augment freshwater without adding any drastic affect to the environment. The objective of this paper was to investigate the potential of using the industrial low grade waste heat to produce freshwater using membrane distillation. The main part of this work was conducting a heat audit on selected Qatari chemical industries to estimate the amounts of freshwater produced if such industrial waste heat were to be recovered. By the end of this work, the main objective was met and the heat audit conducted on the Qatari chemical industries enabled us to estimate both the amounts of waste heat which can be potentially recovered in addition to the amounts of freshwater which can be produced if such waste heat were to be recovered.
By the end, the heat audit showed that around 605 Mega Watts of waste heat can be recovered from the studied Qatari chemical industries which resulted in a total daily production of 5078.7 cubic meter of freshwater.
This water can be used in a wide variety of applications such as human consumption or industry. The amount of produced freshwater may look small when compared to that produced through thermal desalination plants; however, one must bear in mind that this water comes from waste and can be used to supply water for small cities or remote areas which are not connected to the water grid. The idea of producing freshwater from the two widely-available wastes (thermal rejected brine and waste heat) seems promising as less environmental and economic impacts will be associated with freshwater production which may in the near future augment the conventional way of producing freshwater currently being thermal desalination. This work has shown that low grade waste heat in the chemical industries in Qatar and perhaps the rest of the world can contribute to additional production of freshwater using membrane distillation without significantly adding to the environmental impact.
Abstract: This paper deals with a stabilization problem for
multi-agent systems, when all agents in a multi-agent system receive
the same broadcasting control signal and the controller can measure
not each agent output but the sum of all agent outputs. It is
analytically shown that when the sum of all agent outputs is bounded
with a certain broadcasting controller for a given reference, each agent
output is separately bounded: stabilization of the sum of agent outputs
always results in the stability of every agent output. A numerical
example is presented to illustrate our theoretic findings in this paper.
Abstract: Tensile specimens of nonflammable AZ91D Mg alloy were fabricated in this study via cold chamber die-casting process. Dimensions of tensile specimens were 25mm in length, 4mm in width, and 0.8 or 3.0mm in thickness. Microstructure observation was conducted before and after tensile tests at room temperature. In the die casting process, various injection distances from 150 to 260mm were employed to obtain optimum process conditions. Distribution of Al12Mg17 phase was the key factor to determine the mechanical properties of die-cast Mg alloy. Specimens with 3mm of thickness showed superior mechanical properties to those with 0.8mm of thickness. Closed networking of Al12Mg17 phase along grain boundary was found to be detrimental to mechanical properties of die-cast Mg alloy.
Abstract: High temperature deformation behavior of cast 310S stainless steel has been investigated in this study by performing tensile and compression tests at temperatures from 900 to 1200oC. Rectangular ingots of which the dimensions were 350×350×100 in millimeter were cast using vacuum induction melting. Phase equilibrium was calculated using the FactSage®, thermodynamic software and database. Thermal expansion coefficient was also measured on the ingot in the temperature range from room temperature to 1200oC. Tensile strength of cast 310S stainless steel was 9 MPa at 1200oC, which is a little higher than that of a wrought 310S. With temperature decreased, tensile strength increased rapidly and reached up to 72 MPa at 900oC. Elongation also increased with temperature decreased. Microstructure observation revealed that s phase was precipitated along the grain boundary and within the matrix over 1200oC, which is detrimental to high temperature elongation.
Abstract: This paper studies a robust stabilization problem of a
single agent in a multi-agent consensus system composed of identical
agents, when the network topology of the system is completely
unknown. It is shown that the transfer function of an agent in a
consensus system can be described as a multiplicative perturbation
of the isolated agent transfer function in frequency domain. From an
existing robust stabilization result, we present sufficient conditions for
a robust stabilization of an agent against unknown network topology.
Abstract: An accurate study of blood flow is associated with an accurate vascular pattern and geometrical properties of the organ of interest. Due to the complexity of vascular networks and poor accessibility in vivo, it is challenging to reconstruct the entire vasculature of any organ experimentally. The objective of this study is to introduce an innovative approach for the reconstruction of a full vascular tree from available morphometric data. Our method consists of implementing morphometric data on those parts of the vascular tree that are smaller than the resolution of medical imaging methods. This technique reconstructs the entire arterial tree down to the capillaries. Vessels greater than 2 mm are obtained from direct volume and surface analysis using contrast enhanced computed tomography (CT). Vessels smaller than 2mm are reconstructed from available morphometric and distensibility data and rearranged by applying Murray’s Laws. Implementation of morphometric data to reconstruct the branching pattern and applying Murray’s Laws to every vessel bifurcation simultaneously, lead to an accurate vascular tree reconstruction. The reconstruction algorithm generates full arterial tree topography down to the first capillary bifurcation. Geometry of each order of the vascular tree is generated separately to minimize the construction and simulation time. The node-to-node connectivity along with the diameter and length of every vessel segment is established and order numbers, according to the diameter-defined Strahler system, are assigned. During the simulation, we used the averaged flow rate for each order to predict the pressure drop and once the pressure drop is predicted, the flow rate is corrected to match the computed pressure drop for each vessel. The final results for 3 cardiac cycles is presented and compared to the clinical data.
Abstract: In this paper, the behavior of different types of DST columns has been studied under bending load. Briefly, composite columns consist of an internal carbon steel tube and an external stainless steel wall that the between the walls are filled with concrete. Composite columns are expected to combine the advantages of all three materials and have the advantage of high flexural stiffness of CFDST columns. In this research, ABAQUS software is used for finite element analysis then the results of ultimate strength of the composite sections are illustrated.
Abstract: When insulation and rehabilitation of structures is important to use quality building materials with high utility value. One potentially interesting and promising groups of construction materials in this area are advanced, thermally insulating plaster silicate based. With the present trend reduction of energy consumption of building structures and reducing CO2 emissions to be developed capillary-active materials that are characterized by their low density, low thermal conductivity while maintaining good mechanical properties.
The paper describes the results of research activities aimed at the development of thermal insulating and rehabilitation material ongoing at the Technical University in Brno, Faculty of Civil Engineering. The achieved results of this development will be the basis for subsequent experimental analysis of the influence of thermal and moisture loads developed on these materials.
Abstract: The measurement of enterprise-university-research
cooperative efficiency has important meanings in improving the
cooperative efficiency, strengthening the effective integration of
regional resource, enhancing the ability of regional innovation and
promoting the development of regional economy. The paper
constructs the DEA method and DEA-Malmquist productivity index
method to research the cooperation efficiency of Hubei by making
comparisons with other provinces in China. The study found out the
index of technology efficiency is 0.52 and the enterprise-universityresearch
cooperative efficiency is Non-DEA efficient. To realize the
DEA efficiency of Hubei province, the amount of 1652.596 R&D
employees and 638.368 R&D employees’ full time equivalence should
be reduced or 137.89 billion yuan of new products’ sales income be
increased. Finally, it puts forward policy recommendations on existing
problems to strengthen the standings of the cooperation, realize the
effective application of the research results, and improve the level of
management of enterprise-university-research cooperation efficiency.
Abstract: Free vibration analysis of a gabled frame with elastic support and semi-rigid connections is performed by using a program in OpenSees software. Natural frequencies and mode shape details of frame are obtained for two states, which are semi-rigid connections and elastic supports, separately. The members of this structure are analyzed as a prismatic nonlinear beam-column element in software. The mass of structure is considered as two equal lumped masses at the head of two columns in horizontal and vertical directions. Note that the degree of freedom, allocated to all nodes, is equal to three. Furthermore, the mode shapes of frame are achieved. Conclusively, the effects of connections and supports flexibility on the natural frequencies and mode shapes of structure are investigated.
Abstract: This paper reports an advanced approach in the application of CNC machining for rapid manufacturing processes (CNC-RM). The aim of this study is to improve the quality of machined parts by introducing different cutting tools during finishing operations. As the cutting is performed in different directions, the surfaces presented on part can be classified into several categories. Therefore, suitable cutting tools are assigned to machine particular surfaces and to improve the quality. Experimental studies have been carried out by fabricating several parts based on the suggested approach. The results provide further support for implementing this approach in rapid machining processes.
Abstract: Cross-laminated timber is increasingly being used in
the construction of high-rise buildings due to its simple
manufacturing system. In term of fire resistance, cross-laminated
timber panels are promoted as having excellent fire resistance,
comparable to that of non-combustible materials and to heavy
timber construction, due to the ability of thick wood assemblies to
char slowly at a predictable rate while maintaining most of their
strength during the fire exposure. This paper presents an overview of
fire performance of cross-laminated timber and evaluation of its
resistance to elevated temperature in comparison to homogeneous
timber panels. Charring rates for cross-laminated timber panels of
those obtained experimentally were compared with those provided by
Eurocode simplified calculation methods.
Abstract: Packaging for vanadium redox flow battery is one of the key elements for successful implementation of flow battery in the electrical energy storage system. Usually the bulky battery size and low energy densities make this technology not available for mobility application. ThereforeRFB with improved packaging size and energy capacity are highly desirable. This paper focuses on the study of packaging improvement for unit cell V-RFB to the application on Series Hybrid Electric Vehicle. Two different designs of 25cm2 and 100cm2 unit cell V-RFB at same current density are used for the sample in this investigation. Further suggestions on packaging improvement are highlighted.