Abstract: In this experimental study, performance of a counter
flow Ranque-Hilsch vortex tube (RHVT) with threads cut on its inner
surface was investigated experimentally (pitch is 1 and 2 mm). The
inner diameter of the vortex tube used was D=9 mm and the ratio of
the tube’s length to diameter was L/D=12. The experimental system
was a thermodynamic open system. Flow was controlled by a valve
on the hot outlet side, where the valve was changed from a nearly
closed position to its nearly open position. Fraction of cold flow (ξ) =
0.1-0.9, was determined under 300 and 350 kPa pressurized air. All
experimental data were compared with each other, the maximum
heating performance of the RHVT system was found to be 38.2 oC
and the maximum cooling performance of the RHVT in this study
was found to be -30.9 oC at pitch 1 mm.
Abstract: The paper presents an optimization study based on
genetic algorithms (GA-s) for a radio-frequency applicator used in
heating dielectric band products. The weakly coupled electro-thermal
problem is analyzed using 2D-FEM. The design variables in the
optimization process are: the voltage of a supplementary “guard"
electrode and six geometric parameters of the applicator. Two
objective functions are used: temperature uniformity and total active
power absorbed by the dielectric. Both mono-objective and multiobjective
formulations are implemented in GA optimization.
Abstract: Lean manufacturing is a production philosophy made
popular by Toyota Motor Corporation (TMC). It is globally known as
the Toyota Production System (TPS) and has the ultimate aim of
reducing cost by thoroughly eliminating wastes or muda. TPS
embraces the Just-in-time (JIT) manufacturing; achieving cost
reduction through lead time reduction. JIT manufacturing can be
achieved by implementing Pull system in the production.
Furthermore, TPS aims to improve productivity and creating
continuous flow in the production by arranging the machines and
processes in cellular configurations. This is called as Cellular
Manufacturing Systems (CMS). This paper studies on integrating the
CMS with the Pull system to establish a Big Island-Pull system
production for High Mix Low Volume (HMLV) products in an
automotive component industry. The paper will use the build-in JIT
system steps adapted from TMC to create the Pull system production
and also create a shojinka line which, according to takt time, has the
flexibility to adapt to demand changes simply by adding and taking
out manpower. This will lead to optimization in production.
Abstract: The objective of this study was to investigate hydrogen production from alcohol wastewater by anaerobic sequencing batch reactor (ASBR) under thermophillic operation. The ASBR unit used in this study had a liquid holding volume of 4 L and was operated at 6 cycles per day. The seed sludge taken from an upflow anaerobic sludge blanket unit treating the same wastewater was boiled at 95 °C for 15 min before being fed to the ASBR unit. The ASBR system was operated at different COD loading rates at a thermophillic temperature (55 °C), and controlled pH of 5.5. When the system was operated under optimum conditions (providing maximum hydrogen production performance) at a feed COD of 60 000 mg/l, and a COD loading rate of 68 kg/m3 d, the produced gas contained 43 % H2 content in the produced gas. Moreover, the hydrogen yield and the specific hydrogen production rate (SHPR) were 130 ml H2/g COD removed and 2100 ml H2/l d, respectively.
Abstract: Protein structure determination and prediction has
been a focal research subject in the field of bioinformatics due to the
importance of protein structure in understanding the biological and
chemical activities of organisms. The experimental methods used by
biotechnologists to determine the structures of proteins demand
sophisticated equipment and time. A host of computational methods
are developed to predict the location of secondary structure elements
in proteins for complementing or creating insights into experimental
results. However, prediction accuracies of these methods rarely
exceed 70%.
Abstract: In this study, we discussed the effects on the thermal
comfort of super high-rise residences that how effected by the high
thermal capacity structural components. We considered different
building orientations, structures, and insulation methods. We used the
dynamic simulation software THERB (simulation of the thermal
environment of residential buildings). It can estimate the temperature,
humidity, sensible temperature, and heating/cooling load for multiple
buildings. In the past studies, we examined the impact of
air-conditioning loads (hereinafter referred to as AC loads) on the
interior structural parts and the AC-usage patterns of super-high-rise
residences.
Super-high-rise residences have more structural components such
as pillars and beams than do ordinary apartment buildings. The
skeleton is generally made of concrete and steel, which have high
thermal-storage capacities. The thermal-storage capacity of
super-high-rise residences is considered to have a larger impact on the
AC load and thermal comfort than that of ordinary residences.
We show that the AC load of super-high-rise units would be
reduced by installing insulation on the surfaces of interior walls that
are not usually insulated in Japan.
Abstract: The aim of this study is to analyze influence of
differences of heat insulation methods on indoor thermal environment and comfort of apartment buildings.
This study analyzes indoor thermal environment and comfort on units of apartment buildings using calculation software "THERB" and
compares three different kinds of heat insulation methods. Those are
outside insulation on outside walls, inside insulation on outside walls and interior insulation. In terms of indoor thermal environment, outside insulation is the best to stabilize room temperature. In winter, room temperature on
outside insulation after heating is higher than other and it is kept 3-5 degrees higher through all night. But the surface temperature with
outside insulation did not dramatically increase when heating was used, which was 3 to 5oC lower than the temperature with other
insulation. The PMV of interior insulation fall nearly range of comfort when the heating and cooling was use.
Abstract: Nylon 6-clay hybrid/neat nylon 6, sheath/core
bicomponent nanocomposite fibers containing 4 wt% of clay in
sheath section were melt spun at different take-up speeds. Their
orientation and crystalline structure were compared to those of neat
nylon 6 fibers. Birefringence measurements showed that the
orientation development in sheath and core parts of bicomponent
fibers was different. Crystallinity results showed that clay did not act
as a nucleating agent for bicomponent fibers. The neat nylon 6 fiber
had a smooth surface while striped pattern was appeared on the
surface of bicomponent fiber containing clay due to thermal
shrinkage of the core part.
Abstract: Compost manufacturing plants are one of units where
wastewater is produced in significantly large amounts. Wastewater
produced in these plants contains high amounts of substrate (organic
loads) and is classified as stringent waste which creates significant
pollution when discharged into the environment without treatment. A
compost production plant in the one of the Iran-s province treating
200 tons/day of waste is one of the most important environmental
pollutant operations in this zone. The main objectives of this paper
are to investigate the compost wastewater treatability in hybrid
anaerobic reactors with an upflow-downflow arrangement, to
determine the kinetic constants, and eventually to obtain an
appropriate mathematical model. After starting the hybrid anaerobic
reactor of the compost production plant, the average COD removal
rate efficiency was 95%.
Abstract: The previous researches focused on the influence of
anthropogenic greenhouse gases exerting global warming, but not
consider whether desert sand may warm the planet, this could be
improved by accounting for sand's physical and geometric properties.
Here we show, sand particles (because of their geometry) at the desert
surface form an extended surface of up to 1 + π/4 times the planar area
of the desert that can contact sunlight, and at shallow depths of the
desert form another extended surface of at least 1 + π times the planar
area that can contact air. Based on this feature, an enhanced heat
exchange system between sunlight, desert sand, and air in the spaces
between sand particles could be built up automatically, which can
increase capture of solar energy, leading to rapid heating of the sand
particles, and then the heating of sand particles will dramatically heat
the air between sand particles. The thermodynamics of deserts may
thus have contributed to global warming, especially significant to
future global warming if the current desertification continues to
expand.
Abstract: Pretreatment is an essential step in the conversion of
lignocellulosic biomass to fermentable sugar that used for biobutanol
production. Among pretreatment processes, microwave is considered
to improve pretreatment efficiency due to its high heating efficiency,
easy operation, and easily to combine with chemical reaction. The
main objectives of this work are to investigate the feasibility of
microwave pretreatment to enhance enzymatic hydrolysis of
corncobs and to determine the optimal conditions using response
surface methodology. Corncobs were pretreated via two-stage
pretreatment in dilute sodium hydroxide (2 %) followed by dilute
sulfuric acid 1 %. Pretreated corncobs were subjected to enzymatic
hydrolysis to produce reducing sugar. Statistical experimental design
was used to optimize pretreatment parameters including temperature,
residence time and solid-to-liquid ratio to achieve the highest amount
of glucose. The results revealed that solid-to-liquid ratio and
temperature had a significant effect on the amount of glucose.
Abstract: Among the technologies available to reduce methane
emitted from the pig industry, biofiltration seems to be an effective
and inexpensive solution. In methane (CH4) biofiltration, nitrogen is
an important macronutrient for the microorganisms growth. The
objective of this research project was to study the effect of
ammonium (NH4
+) on the performance, the biomass production and
the nitrogen conversion of a biofilter treating methane. For NH4
+
concentrations ranging from 0.05 to 0.5 gN-NH4
+/L, the CH4 removal
efficiency and the dioxide carbon production rate decreased linearly
from 68 to 11.8 % and from 7.1 to 0.5 g/(m3-h), respectively. The dry
biomass content varied from 4.1 to 5.8 kg/(m3 filter bed). For the
same range of concentrations, the ammonium conversion decreased
while the specific nitrate production rate increased. The specific
nitrate production rate presented negative values indicating
denitrification in the biofilter.
Abstract: This study evaluated the microbiological quality
and the sensory characteristics of carp fillets processed by the
sousvide method when stored at 2 and 10 °C. Four different
combinations of sauced–storage were studied then stored at 2 or 10
°C was evaluate periodically sensory, microbiological and
chemical quality. Batches stored at 2 °C had lower growth rates of
mesophiles and psychrotrophs. Moreover, these counts decreased
by increasing the heating temperature and time. Staphylococcus
aureus, Bacillus cereus, Clostridium perfringens and Listeria
monocytogenes were not found in any of the samples. The heat
treatment of 90 °C for 15 min and sauced was the most effective to
ensure the safety and extend the shelf-life of sousvide carp
preserving its sensory characteristics. This study establishes the
microbiological quality of sous vide carp and emphasizes the
relevance of the raw materials, heat treatment and storage
temperature to ensure the safety of the product.
Abstract: The ability to predict an accurate temperature
distribution requires the knowledge of the losses, the thermal
characteristics of the materials, and the cooling conditions, all of
which are very difficult to quantify. In this paper, the impact of the
effects of iron and copper losses are investigated separately and
their effects on the heating in various points of the stator of an
induction motor, is highlighted by using two simple tests. In addition,
the effect of a defect, such as an open circuit in a phase of the stator,
on the heating is also obtained by a no-load test.
The squirrel cage induction motor is rated at 2.2 kW; 380 V; 5.2
A; Δ connected; 50 Hz; 1420 rpm and the class of insulation F, has
been thermally tested under several load conditions. Several
thermocouples were placed in strategic points of the stator.
Abstract: Viscous heating becomes significant in the high speed
resin coating process of glass fibers for optical fiber manufacturing.
This study focuses on the coating resin flows inside the capillary
coating die of optical fiber coating applicator and they are numerically
simulated to examine the effects of viscous heating and subsequent
temperature increase in coating resin. Resin flows are driven by fast
moving glass fiber and the pressurization at the coating die inlet, while
the temperature dependent viscosity of liquid coating resin plays an
important role in the resin flow. It is found that the severe viscous
heating near the coating die wall profoundly alters the radial velocity
profiles and that the increase of final coating thickness by die
pressurization is amplified if viscous heating is present.
Abstract: The aim of this study is to develop mathematical
relationships for the performance parameter brake thermal efficiency
(BTE) and emission parameter nitrogen oxides (NOx) for the various
esters of vegetable oils used as CI engine fuel. The BTE is an
important performance parameter defining the ability of engine to
utilize the energy supplied and power developed similarly it is
indication of efficiency of fuels used. The esters of cottonseed oil,
soybean oil, jatropha oil and hingan oil are prepared using
transesterification process and characterized for their physical and
main fuel properties including viscosity, density, flash point and
higher heating value using standard test methods. These esters are
tried as CI engine fuel to analyze the performance and emission
parameters in comparison to diesel. The results of the study indicate
that esters as a fuel does not differ greatly with that of diesel in
properties. The CI engine performance with esters as fuel is in line
with the diesel where as the emission parameters are reduced with the
use of esters.
The correlation developed between BTE and brake power(BP),
gross calorific value(CV), air-fuel ratio(A/F), heat carried away by
cooling water(HCW). Another equation is developed between the
NOx emission and CO, HC, smoke density (SD), exhaust gas
temperature (EGT). The equations are verified by comparing the
observed and calculated values which gives the coefficient of
correlation of 0.99 and 0.96 for the BTE and NOx equations
respectively.
Abstract: The main objective of this paper is to provide an efficient tool for delineating brain tumors in three-dimensional magnetic resonance images. To achieve this goal, we use basically a level-sets approach to delineating three-dimensional brain tumors. Then we introduce a compression plan of 3D brain structures based for the meshes simplification, adapted for time to the specific needs of the telemedicine and to the capacities restricted by network communication. We present here the main stages of our system, and preliminary results which are very encouraging for clinical practice.
Abstract: Oxide scale thickness measurements are used in assessing the life of different components operating at high temperature environment. Such measurements provide an approximation for the temperature inside components such as reheater and superheater tubes. A number of failures were encountered in one of the boilers in one of Kuwaiti power plants. These failure were mainly in the first row of the primary super heater tubes, therefore, the specialized engineer decide to replace them during the annual shutdown. As a tool for failure analysis, oxide scale thickness measurement were used to investigate the temperature distribution in these tubes. In this paper, the oxide scale thickness of these tubes were measured and used for analysis. The measurements provide an illustration of the distribution of heat transfer of the primary superheater tubes in the boiler system. Remarks and analysis about the design of the boiler are also provided.
Abstract: This paper examines ethical and social issues which
have proved important when initiating and creating educational spaces within a virtual environment. It focuses on one project, identifying the key decisions made, the barriers to new practice
encountered and the impact these had on the project. It demonstrates
the importance of the 'backstage' ethical and social issues involved in
the creation of a virtual education community and offers conclusions,
and questions, which will inform future research and practice in this
area. These ethical issues are considered using Knobel-s framework
of front-end, in-process and back-end concerns, and include
establishing social practices for the islands, allocating access rights,
considering personal safety and supporting researchers appropriately
within this context.
Abstract: A numerical study on the influence of forward-facing
cavity length upon forward-facing cavity and opposing jet combined
thermal protection system (TPS) cooling efficiency under hypersonic
flow is conducted, by means of which the flow field parameters, heat
flux distribution along the outer body surface are obtained. The
numerical simulation results are validated by experiments and the
cooling effect of the combined TPS with different cavity length is
analyzed. The numerical results show that the combined configuration
dose well in cooling the nose of the hypersonic vehicle. The deeper the
cavity is, the weaker the heat flux is. The recirculation region plays a
key role for the reduction of the aerodynamic heating.