Abstract: Water spray cooling is a technique typically used in
heat treatment and other metallurgical processes where controlled
temperature regimes are required. Water spray cooling is used in
static (without movement) or dynamic (with movement of the steel
plate) regimes. The static regime is notable for the fixed position of
the hot steel plate and fixed spray nozzle. This regime is typical for
quenching systems focused on heat treatment of the steel plate. The
second application of spray cooling is the dynamic regime. The
dynamic regime is notable for its static section cooling system and
moving steel plate. This regime is used in rolling and finishing mills.
The fixed position of cooling sections with nozzles and the
movement of the steel plate produce nonhomogeneous water
distribution on the steel plate. The length of cooling sections and
placement of water nozzles in combination with the nonhomogeneity
of water distribution lead to discontinued or interrupted cooling
conditions. The impact of static and dynamic regimes on cooling
intensity and the heat transfer coefficient during the cooling process
of steel plates is an important issue.
Heat treatment of steel is accompanied by oxide scale growth. The
oxide scale layers can significantly modify the cooling properties and
intensity during the cooling. The combination of static and dynamic
(section) regimes with the variable thickness of the oxide scale layer
on the steel surface impact the final cooling intensity. The study of
the influence of the oxide scale layers with different cooling regimes
was carried out using experimental measurements and numerical
analysis. The experimental measurements compared both types of
cooling regimes and the cooling of scale-free surfaces and oxidized
surfaces. A numerical analysis was prepared to simulate the cooling
process with different conditions of the section and samples with
different oxide scale layers.
Abstract: Currently, thorium fuel has been especially noticed
because of its proliferation resistance than long half-life alpha emitter
minor actinides, breeding capability in fast and thermal neutron flux
and mono-isotopic naturally abundant. In recent years, efficiency of
minor actinide burning up in PWRs has been investigated. Hence, a
minor actinide-contained thorium based fuel matrix can confront both
proliferation resistance and nuclear waste depletion aims. In the
present work, minor actinide depletion rate in a CANDU-type nuclear
core modeled using MCNP code has been investigated. The obtained
effects of minor actinide load as mixture of thorium fuel matrix on
the core neutronics has been studied with comparing presence and
non-presence of minor actinide component in the fuel matrix.
Depletion rate of minor actinides in the MA-contained fuel has been
calculated using different power loads. According to the obtained
computational data, minor actinide loading in the modeled core
results in more negative reactivity coefficients. The MA-contained
fuel achieves less radial peaking factor in the modeled core. The
obtained computational results showed 140 kg of 464 kg initial load
of minor actinide has been depleted in during a 6-year burn up in 10
MW power.
Abstract: In this paper, student admission process is studied to
optimize the assignment of vacant seats with three main objectives.
Utilizing all vacant seats, satisfying all programs of study admission
requirements and maintaining fairness among all candidates are the
three main objectives of the optimization model. Seat Assignment
Method (SAM) is used to build the model and solve the optimization
problem with help of Northwest Coroner Method and Least Cost
Method. A closed formula is derived for applying the priority of
assigning seat to candidate based on SAM.
Abstract: Operations research science (OR) deals with good
success in developing and applying scientific methods for problem
solving and decision-making. However, by using OR techniques, we
can enhance the use of computer decision support systems to achieve
optimal management for institutions. OR applies comprehensive
analysis including all factors that effect on it and builds mathematical
modeling to solve business or organizational problems. In addition, it
improves decision-making and uses available resources efficiently.
The adoption of OR by universities would definitely contributes to
the development and enhancement of the performance of OR
techniques. This paper provides an understanding of the structures,
approaches and models of OR in problem solving and decisionmaking.
Abstract: Factors affecting construction unit cost vary
depending on a country’s political, economic, social and
technological inclinations. Factors affecting construction costs have
been studied from various perspectives. Analysis of cost factors
requires an appreciation of a country’s practices. Identified cost
factors provide an indication of a country’s construction economic
strata. The purpose of this paper is to identify the essential factors
that affect unit cost estimation and their breakdown using artificial
neural networks. Twenty five (25) identified cost factors in road
construction were subjected to a questionnaire survey and employing
SPSS factor analysis the factors were reduced to eight. The 8 factors
were analysed using neural network (NN) to determine the
proportionate breakdown of the cost factors in a given construction
unit rate. NN predicted that political environment accounted 44% of
the unit rate followed by contractor capacity at 22% and financial
delays, project feasibility and overhead & profit each at 11%. Project
location, material availability and corruption perception index had
minimal impact on the unit cost from the training data provided.
Quantified cost factors can be incorporated in unit cost estimation
models (UCEM) to produce more accurate estimates. This can create
improvements in the cost estimation of infrastructure projects and
establish a benchmark standard to assist the process of alignment of
work practises and training of new staff, permitting the on-going
development of best practises in cost estimation to become more
effective.
Abstract: Carbon fiber reinforced polymersarewidely used to strengthen steel structural elements. These structural elements are normally subjected to static, dynamic and fatigue loadings during their life-time. CFRP laminate is commonly used to strengthen these structures under the subjected loads. A number of studies have focused on the characteristics of CFRP sheets bonded to steel members under static, dynamic and fatigue loadings. However, there is a gap in understanding the bonding behavior between CFRP laminates and steel members under impact loading. This paper shows the effect of high load rates on this bond. CFRP laminate CFK 150/2000 was used to strengthen steel joints using Araldite 420 epoxy. The results show that applying a high load rate significantly affects the bond strength but has little influence on the effective bond length.
Abstract: The thermal conductivity of a fluid can be
significantly enhanced by dispersing nano-sized particles in it, and
the resultant fluid is termed as "nanofluid". A theoretical model for
estimating the thermal conductivity of a nanofluid has been proposed
here. It is based on the mechanism that evenly dispersed
nanoparticles within a nanofluid undergo Brownian motion in course
of which the nanoparticles repeatedly collide with the heat source.
During each collision a rapid heat transfer occurs owing to the solidsolid
contact. Molecular dynamics (MD) simulation of the collision
of nanoparticles with the heat source has shown that there is a pulselike
pick up of heat by the nanoparticles within 20-100 ps, the extent
of which depends not only on thermal conductivity of the
nanoparticles, but also on the elastic and other physical properties of
the nanoparticle. After the collision the nanoparticles undergo
Brownian motion in the base fluid and release the excess heat to the
surrounding base fluid within 2-10 ms. The Brownian motion and
associated temperature variation of the nanoparticles have been
modeled by stochastic analysis. Repeated occurrence of these events
by the suspended nanoparticles significantly contributes to the
characteristic thermal conductivity of the nanofluids, which has been
estimated by the present model for a ethylene glycol based nanofluid
containing Cu-nanoparticles of size ranging from 8 to 20 nm, with
Gaussian size distribution. The prediction of the present model has
shown a reasonable agreement with the experimental data available
in literature.
Abstract: Climate change confronts the built environment with
many new challenges in the form of more severe and frequent hydrometeorological
events. A series of strategies is proposed whereby the
various aspects of buildings and their sites can be made more resilient
to the effects of such events.
Abstract: Artificial Neural Network (ANN) can be trained using
back propagation (BP). It is the most widely used algorithm for
supervised learning with multi-layered feed-forward networks.
Efficient learning by the BP algorithm is required for many practical
applications. The BP algorithm calculates the weight changes of
artificial neural networks, and a common approach is to use a twoterm
algorithm consisting of a learning rate (LR) and a momentum
factor (MF). The major drawbacks of the two-term BP learning
algorithm are the problems of local minima and slow convergence
speeds, which limit the scope for real-time applications. Recently the
addition of an extra term, called a proportional factor (PF), to the
two-term BP algorithm was proposed. The third increases the speed
of the BP algorithm. However, the PF term also reduces the
convergence of the BP algorithm, and criteria for evaluating
convergence are required to facilitate the application of the three
terms BP algorithm. Although these two seem to be closely related,
as described later, we summarize various improvements to overcome
the drawbacks. Here we compare the different methods of
convergence of the new three-term BP algorithm.
Abstract: There exists some time lag between the consumption of
inputs and the production of outputs. This time lag effect should be
considered in calculating efficiency of decision making units (DMU).
Recently, a couple of DEA models were developed for considering
time lag effect in efficiency evaluation of research activities. However,
these models can’t discriminate efficient DMUs because of the nature
of basic DEA model in which efficiency scores are limited to ‘1’. This
problem can be resolved a super-efficiency model. However, a super
efficiency model sometimes causes infeasibility problem. This paper
suggests an output oriented super-efficiency model for efficiency
evaluation under the consideration of time lag effect. A case example
using a long term research project is given to compare the suggested
model with the MpO model.
Abstract: Developing young people’s employability is a key
policy issue for ensuring their successful transition to the labour
market and their access to career oriented employment. The youths of
today irrespective of their gender need to acquire the knowledge,
skills and attitudes that will enable them to create or find jobs as well
as cope with unpredictable labour market changes throughout their
working lives. In a study carried out to determine the influence of
gender on job-competencies requirements of chemical-based
industries and undergraduate-competencies acquisition by chemists
working in the industries, all chemistry graduates working in twenty
(20) chemical-based industries that were randomly selected from six
sectors of chemical-based industries in Lagos and Ogun States of
Nigeria were administered with Job-competencies required and
undergraduate-competencies acquired assessment questionnaire. The
data were analysed using means and independent sample t-test. The
findings revealed that the population of female chemists working in
chemical-based industries is low compared with the number of male
chemists; furthermore, job-competencies requirements are found not
to be gender biased while there is no significant difference in
undergraduate-competencies acquisition of male and female
chemists. This suggests that females should be given the same
opportunity of employment in chemical-based industries as their male
counterparts. The study also revealed the level of acquisition of
undergraduate competencies as related to the needs of chemicalbased
industries.
Abstract: The purpose of this study was to reduce patient
waiting times, improve system throughput and improve resources
utilization in radiology department. A discrete event simulation
model was developed using Arena simulation software to investigate
different alternatives to improve the overall system delivery based on
adding resource scenarios due to the linkage between patient waiting
times and resource availability. The study revealed that there is no
addition investment need to procure additional scanner but hospital
management deploy managerial tactics to enhance machine
utilization and reduce the long waiting time in the department.
Abstract: In this paper, effect of marginal quality groundwater
on yield of cotton crop and soil salinity was studied. In this
connection, three irrigation treatments each with four replications
were applied. These treatments were i) use of canal water (T1), ii) use
of marginal quality groundwater from tubewell (T2), and iii)
conjunctive use by mixing with the ratio of 1:1 of canal water and
marginal quality tubewell water (T3).
Water was applied to the crop cultivated in Kharif season 2011; its
quantity has been measured using cut-throat flume. Total 11 watering
each of 50 mm depth have been applied from 20th April to 20th July,
2011. Further, irrigations were stopped due to monsoon rainfall up to
crop harvesting.
Maximum crop yield (seed cotton) was observed under T1 which
was 1,517 kg/ha followed by T3 (mixed canal and tubewell water)
having 1009 kg/ha and T2 i.e. marginal quality groundwater having
709 kg/ha. This concludes that crop yield in T2 and T3 in comparison
to T1was reduced by about 53 and 30% respectively.
It has been observed that yield of cotton crop is below potential
limit for three treatments due to unexpected rainfall at the time of full
flowering season; thus the yield was adversely affected.
However, salt deposition in soil profiles was not observed that is
due to leaching effect of heavy rainfall occurred during monsoon
season.
Abstract: In this study which has been conducted in Akçasu
Forest Range District of Devrek Forest Directorate; 3 methods (weed
control with labourer power, cover removal with Hitachi F20
Excavator, and weed control with agricultural equipment mounted on
a Ferguson 240S agriculture tractor) were utilized in weed control
efforts in regeneration of degraded oriental beech forests have been
compared. In this respect, 3 methods have been compared by
determining certain work hours and standard durations of unit areas
(1 hectare). For this purpose, evaluating the tasks made with human
and machine force from the aspects of duration, productivity and
costs, it has been aimed to determine the most productive method in
accordance with the actual ecological conditions of research field.
Within the scope of the study, the time studies have been conducted
for 3 methods used in weed control efforts. While carrying out those
studies, the performed implementations have been evaluated by
dividing them into business stages. Also, the actual data have been
used while calculating the cost accounts. In those calculations, the
latest formulas and equations which are also used in developed
countries have been utilized. The variance of analysis (ANOVA) was
used in order to determine whether there is any statistically
significant difference among obtained results, and the Duncan test
was used for grouping if there is significant difference. According to
the measurements and findings carried out within the scope of this
study, it has been found during living cover removal efforts in
regeneration efforts in demolished oriental beech forests that the
removal of weed layer in 1 hectare of field has taken 920 hours with
labourer force, 15.1 hours with excavator and 60 hours with an
equipment mounted on a tractor. On the other hand, it has been
determined that the cost of removal of living cover in unit area (1
hectare) was 3220.00 TL for labourer power, 1250 TL for excavator
and 1825 TL for equipment mounted on a tractor.
According to the obtained results, it has been found that the
utilization of excavator in weed control effort in regeneration of
degraded oriental beech regions under actual ecological conditions of
research field has been found to be more productive from both of
aspects of duration and costs. These determinations carried out
should be repeated in weed control efforts in degraded forest fields
with different ecological conditions, it is compulsory for finding the
most efficient weed control method. These findings will light the way
of technical staff of forestry directorate in determination of the most
effective and economic weed control method. Thus, the more actual
data will be used while preparing the weed control budgets, and there
will be significant contributions to national economy. Also the results of this and similar studies are very important for developing the policies for our forestry in short and long term.
Abstract: Liposome plays an important role in medical and
pharmaceutical science as e.g. nano scale drug carriers. Liposomes
are vesicles of varying size consisting of a spherical lipid bilayer and
an aqueous inner compartment. Magnet-driven liposome used for the
targeted delivery of drugs to organs and tissues. These liposome
preparations contain encapsulated drug components and finely
dispersed magnetic particles.
Liposomes are vesicles of varying size consisting of a spherical
lipid bilayer and an aqueous inner compartment that are generated in
vitro. These are useful in terms of biocompatibility, biodegradability,
and low toxicity, and can control biodistribution by changing the size,
lipid composition, and physical characteristics. Furthermore,
liposomes can entrap both hydrophobic and hydrophilic drugs and are
able to continuously release the entrapped substrate, thus being useful
drug carriers. Magnetic liposomes (MLs) are phospholipid vesicles
that encapsulate magneticor paramagnetic nanoparticles. They are
applied as contrast agents for magnetic resonance imaging (MRI).
The biological synthesis of nanoparticles using plant extracts plays
an important role in the field of nanotechnology. Green-synthesized
magnetite nanoparticles-protein hybrid has been produced by treating
Iron (III) / Iron (II) chloride with the leaf extract of Datura inoxia.
The phytochemicals present in the leaf extracts act as a reducing as
well stabilizing agents preventing agglomeration, which include
flavonoids, phenolic compounds, cardiac glycosides, proteins and
sugars.
The magnetite nanoparticles-protein hybrid has been trapped
inside the aqueous core of the liposome prepared by reversed phase
evaporation (REV) method using oleic and linoleic acid which has
been shown to be driven under magnetic field confirming the
formation magnetic liposome (ML). Chemical characterization of
stealth magnetic liposome has been performed by breaking the
liposome and release of magnetic nanoparticles. The presence iron
has been confirmed by colour complex formation with KSCN and
UV-Vis study using spectrophotometer Cary 60, Agilent.
This magnet driven liposome using nanoparticles-protein hybrid
can be a smart vesicles for the targeted drug delivery.
Abstract: Over the last few decades, oilfield service rolling
equipment has significantly increased in weight, primarily because of
emissions regulations, which require larger/heavier engines, larger
cooling systems, and emissions after-treatment systems, in some
cases, etc. Larger engines cause more vibration and shock loads,
leading to failure of electronics and control systems.
If the vibrating frequency of the engine matches the system
frequency, high resonance is observed on structural parts and mounts.
One such existing automated control equipment system comprising
wire rope mounts used for mounting computers was designed
approximately 12 years ago. This includes the use of an industrialgrade
computer to control the system operation. The original
computer had a smaller, lighter enclosure. After a few years, a newer
computer version was introduced, which was 10 lbm heavier. Some
failures of internal computer parts have been documented for cases in
which the old mounts were used. Because of the added weight, there
is a possibility of having the two brackets impact each other under
off-road conditions, which causes a high shock input to the computer
parts. This added failure mode requires validating the existing mount
design to suit the new heavy-weight computer.
This paper discusses the modal finite element method (FEM)
analysis and experimental modal analysis conducted to study the
effects of vibration on the wire rope mounts and the computer. The
existing mount was modelled in ANSYS software, and resultant
mode shapes and frequencies were obtained. The experimental modal
analysis was conducted, and actual frequency responses were
observed and recorded.
Results clearly revealed that at resonance frequency, the brackets
were colliding and potentially causing damage to computer parts. To
solve this issue, spring mounts of different stiffness were modeled in
ANSYS software, and the resonant frequency was determined.
Increasing the stiffness of the system increased the resonant
frequency zone away from the frequency window at which the engine
showed heavy vibrations or resonance. After multiple iterations in
ANSYS software, the stiffness of the spring mount was finalized,
which was again experimentally validated.
Abstract: Periventricular Leukomalacia (PVL) is a White Matter
Injury (WMI) of preterm neonatal brain. Objectives of the study were
to assess the neuro-developmental outcome at one year of age and to
determine a good protocol of cranial ultrasonography to detect PVL.
Two hundred and sixty four preterm neonates were included in the
study. Series of cranial ultrasound scans were done by using a
dedicated neonatal head probe 4-10 MHz of Logic e portable
ultrasound scanner. Clinical history of seizures, abnormal head
growth (hydrocephalus or microcephaly) and developmental
milestones were assessed and neurological examinations were done
until one year of age. Among live neonates, 57% who had cystic PVL
(Grades 2 and 3) manifested as cerebral palsy. In conclusion cystic
PVL has permanent neurological disabilities like cerebral palsy.
Good protocol of real time cranial ultrasonography to detect PVL is
to perform scans at least once a week until one month and at term (40
weeks of gestation).
Abstract: Science and technology has a major impact on many
societal domains such as communication, medicine, food,
transportation, etc. However, this dominance of modern technology
can have a negative unintended impact on indigenous systems, and in
particular on indigenous foods. This problem serves as a motivation
to this study whose aim is to examine the perceptions of learners on
the usefulness of Information and Communication Technologies
(ICTs) for learning about indigenous foods. This aim will be
subdivided into two types of research objectives. The design and
identification of theories and models will be achieved using literature
content analysis. The objective on the empirical testing of such
theories and models will be achieved through the survey of
Hospitality studies learners from different schools in the iLembe and
Umgungundlovu Districts of the South African Kwazulu-Natal
province. SPSS is used to quantitatively analyze the data collected by
the questionnaire of this survey using descriptive statistics and
Pearson correlations after the assessment of the validity and the
reliability of the data. The main hypothesis behind this study is that
there is a connection between the demographics of learners, their
perceptions on the usefulness of ICTs for learning about indigenous
foods, and the following personality and eLearning related theories
constructs: Computer self-efficacy, Trust in ICT systems, and
Conscientiousness; as suggested by existing studies on learning
theories. This hypothesis was fully confirmed by the survey
conducted by this study except for the demographic factors where
gender and age were not found to be determinant factors of learners’
perceptions on the usefulness of ICTs for learning about indigenous
foods.
Abstract: Cross flow water tube heat exchanger can be designed
and made operational using methods of model building and
simulation of the system. This paper projects the design and
development of a model of cross flow water tube heat-exchanger
system, simulation and validation of control analysis of different
tuning methods. Feedback and override control system is developed
using inputs acquired with the help of sensory system. A
mathematical model is formulated for analysis of system behaviour.
The temperature is regulated at the desired set point automatically.
Abstract: Geopolymer concretes are new class of construction
materials that have emerged as an alternative to Ordinary Portland
cement concrete. Considerable researches have been carried out on
material development of geopolymer concrete; however, a few studies
have been reported on the structural use of them. This paper presents
the bond behaviors of reinforcement embedded in fly ash based
geopolymer concrete. The development lengths of reinforcement for
various compressive strengths of concrete, 20, 30 and 40 MPa, and
reinforcement diameters, 10, 16 and 25 mm, are investigated. Total 27
specimens were manufactured and pull-out test according to EN 10080
was applied to measure bond strength and slips between concrete and
reinforcements. The average bond strengths decreased from 23.06MPa
to 17.26 MPa, as the diameters of reinforcements increased from
10mm to 25mm. The compressive strength levels of geopolymer
concrete showed no significant influence on bond strengths in this
study. Also, the bond-slip relations between geopolymer concrete and
reinforcement are derived using non-linear regression analysis for
various experimental conditions.