Abstract: The quantitative determination of several trace
elements (Cr, As, Se, Cd, Hg, Pb) existing as inorganic impurities in
some oriental herb-products such as Lingzhi Mushroom capsules,
Philamin powder, etc using ICP-MS has been studied. Various
instrumental parameters such as power, gas flow rate, sample depth, as
well as the concentration of nitric acid and thick background due to
high concentration of possible interferences on the determination of
these above-mentioned elements was investigated and the optimum
working conditions of the sample measurement on ICP-MS
(Agilent-7500a) were reported. Appropriate isotope internal standards
were also used to improve the accuracy of mercury determination.
Optimal parameters for sampling digestion were also investigated. The
recovery of analytical procedure was examined by using a Certified
Reference Material (IAEA-CRM 359). The recommended procedure
was then applied for the quantitative determination of Cr, As, Se, Cd,
Hg, Pb in Lingzhi Mushroom capsule, and Philamine powder samples.
The reproducibility of sample measurement (average value between
94 and 102%) and the uncertainty of analytical data (less than 20%)
are acceptable.
Abstract: Large scale climate signals and their teleconnections can influence hydro-meteorological variables on a local scale. Several extreme flow and timing measures, including high flow and low flow measures, from 62 hydrometric stations in Canada are investigated to detect possible linkages with several large scale climate indices. The streamflow data used in this study are derived from the Canadian Reference Hydrometric Basin Network and are characterized by relatively pristine and stable land-use conditions with a minimum of 40 years of record. A composite analysis approach was used to identify linkages between extreme flow and timing measures and climate indices. The approach involves determining the 10 highest and 10 lowest values of various climate indices from the data record. Extreme flow and timing measures for each station were examined for the years associated with the 10 largest values and the years associated with the 10 smallest values. In each case, a re-sampling approach was applied to determine if the 10 values of extreme flow measures differed significantly from the series mean. Results indicate that several stations are impacted by the large scale climate indices considered in this study. The results allow the determination of any relationship between stations that exhibit a statistically significant trend and stations for which the extreme measures exhibit a linkage with the climate indices.
Abstract: In this study, to compress ECG signals, KLT (Karhunen-
Loeve Transform) method has been used. The purpose of this method is to
perform effective ECG coding by a correlation between the length of frames
and the number of vectors of ECG signals.
Abstract: This paper explores steady-state characteristics of
grid-connected doubly fed induction motor (DFIM) in case of unity
power factor operation. Based on the synchronized mathematical
model, analytic determination of the control laws is presented and
illustrated by various figures to understand the effect of the applied
rotor voltage on the speed and the active power. On other hand,
unlike previous works where the stator resistance was neglected, in
this work, stator resistance is included such that the equations can be
applied to small wind turbine generators which are becoming more
popular. Finally the work is crowned by integration of the studied
induction generator in a wind system where an open loop control is
proposed confers a remarkable simplicity of implementation
compared to the known methods.
Abstract: The design of technological procedures for
manufacturing certain products demands the definition and
optimization of technological process parameters. Their
determination depends on the model of the process itself and its
complexity. Certain processes do not have an adequate mathematical
model, thus they are modeled using heuristic methods. First part of
this paper presents a state of the art of using soft computing
techniques in manufacturing processes from the perspective of
applicability in modern CAx systems. Methods of artificial
intelligence which can be used for this purpose are analyzed. The
second part of this paper shows some of the developed models of
certain processes, as well as their applicability in the actual
calculation of parameters of some technological processes within the
design system from the viewpoint of productivity.
Abstract: One of Effective parameters on the performance of linear induction motors is number of poles which must be selected and optimized to increase power efficiency and motor performance significantly. In this paper a double-sided linear induction motor with different poles number by using MAXWELL3D software is designed and with finite element method is analyzed electromagnetically. Then for dynamic simulation, linear motor by using MATLAB software is simulated. The results show that by adding poles number, system time response is increased and motor after more time reaches to steady state. Also propulsion force of motor is increased.
Abstract: Genetic Algorithms (GAs) are direct searching
methods which require little information from design space. This
characteristic beside robustness of these algorithms makes them to be
very popular in recent decades. On the other hand, while this method
is employed, there is no guarantee to achieve optimum results. This
obliged designer to run such algorithms more than one time to
achieve more reliable results. There are many attempts to modify the
algorithms to make them more efficient. In this paper, by application
of fractal dimension (particularly, Box Counting Method), the
complexity of design space are established for determination of
mutation and crossover probabilities (Pm and Pc). This methodology
is followed by a numerical example for more clarification. It is
concluded that this modification will improve efficiency of GAs and
make them to bring about more reliable results especially for design
space with higher fractal dimensions.
Abstract: We present a novel scheme to recognize isolated speech
signals using certain statistical parameters derived from those signals.
The determination of the statistical estimates is based on extracted
signal information rather than the original signal information in
order to reduce the computational complexity. Subtle details of
these estimates, after extracting the speech signal from ambience
noise, are first exploited to segregate the polysyllabic words from
the monosyllabic ones. Precise recognition of each distinct word is
then carried out by analyzing the histogram, obtained from these
information.
Abstract: The study of the generated defects on manufactured
parts shows the difficulty to maintain parts in their positions during
the machining process and to estimate them during the pre-process
plan. This work presents a contribution to the development of 3D
models for the optimization of the manufacturing tolerances. An
experimental study allows the measurement of the defects of part
positioning for the determination of ε and the choice of an optimal
setup of the part. An approach of 3D tolerance based on the small
displacements method permits the determination of the
manufacturing errors upstream. A developed tool, allows an
automatic generation of the tolerance intervals along the three axes.
Abstract: In real-field applications, the correct determination of voice segments highly improves the overall system accuracy and minimises the total computation time. This paper presents reliable measures of speech compression by detcting the end points of the speech signals prior to compressing them. The two different compession schemes used are the Global threshold and the Level- Dependent threshold techniques. The performance of the proposed method is tested wirh the Signal to Noise Ratios, Peak Signal to Noise Ratios and Normalized Root Mean Square Error parameter measures.
Abstract: Square pipes (pipes with square cross sections) are
being used for various industrial objectives, such as machine
structure components and housing/building elements. The utilization
of them is extending rapidly and widely. Hence, the out-put of those
pipes is increasing and new application fields are continually
developing.
Due to various demands in recent time, the products have to
satisfy difficult specifications with high accuracy in dimensions. The
reshaping process design of pipes with square cross sections;
however, is performed by trial and error and based on expert-s
experience.
In this paper, a computer-aided simulation is developed based on
the 2-D elastic-plastic method with consideration of the shear
deformation to analyze the reshaping process. Effect of various
parameters such as diameter of the circular pipe and mechanical
properties of metal on product dimension and quality can be
evaluated by using this simulation. Moreover, design of reshaping
process include determination of shrinkage of cross section,
necessary number of stands, radius of rolls and height of pipe at each
stand, are investigated. Further, it is shown that there are good
agreements between the results of the design method and the
experimental results.
Abstract: This is an application research presenting the
improvement of production quality using the six sigma solutions and
the analyses of benefit-cost ratio. The case of interest is the
production of tile-concrete. Such production has faced with the
problem of high nonconforming products from an inappropriate
surface coating and had low process capability based on the strength
property of tile. Surface coating and tile strength are the most critical
to quality of this product. The improvements followed five stages of
six sigma solutions. After the improvement, the production yield was
improved to 80% as target required and the defective products from
coating process was remarkably reduced from 29.40% to 4.09%. The
process capability based on the strength quality was increased from
0.87 to 1.08 as customer oriented. The improvement was able to save
the materials loss for 3.24 millions baht or 0.11 million dollars. The
benefits from the improvement were analyzed from (1) the reduction
of the numbers of non conforming tile using its factory price for
surface coating improvement and (2) the materials saved from the
increment of process capability. The benefit-cost ratio of overall
improvement was high as 7.03. It was non valuable investment in
define, measure, analyses and the initial of improve stages after that
it kept increasing. This was due to there were no benefits in define,
measure, and analyze stages of six sigma since these three stages
mainly determine the cause of problem and its effects rather than
improve the process. The benefit-cost ratio starts existing in the
improve stage and go on. Within each stage, the individual benefitcost
ratio was much higher than the accumulative one as there was an
accumulation of cost since the first stage of six sigma. The
consideration of the benefit-cost ratio during the improvement
project helps make decisions for cost saving of similar activities
during the improvement and for new project. In conclusion, the
determination of benefit-cost ratio behavior through out six sigma
implementation period provides the useful data for managing quality
improvement for the optimal effectiveness. This is the additional
outcome from the regular proceeding of six sigma.
Abstract: Contamination of heavy metals in tin tailings has
caused an interest in the scientific approach of their remediation. One
of the approaches is through phytoremediation, which is using tree
species to extract the heavy metals from the contaminated soils. Tin
tailings comprise of slime and sand tailings. This paper reports only
on the finding of the four timber species namely Acacia mangium,
Hopea odorata, Intsia palembanica and Swietenia macrophylla on
the removal of cadmium (Cd) and lead (Pb) from the slime tailings.
The methods employed for sampling and soil analysis are established
methods. Six trees of each species were randomly selected from a
0.25 ha plot for extraction and determination of their heavy metals.
The soil samples were systematically collected according to 5 x 5 m
grid from each plot. Results showed that the concentration of heavy
metals in soils and trees varied according to species. Higher
concentration of heavy metals was found in the stem than the
primary roots of all the species. A. Mangium accumulated the highest
total amount of Pb per hectare basis.
Abstract: The rangelands, as one of the largest dynamic biomes
in the world, have very capabilities. Regulation of greenhouse gases
in the Earth's atmosphere, particularly carbon dioxide as the main
these gases, is one of these cases. The attention to rangeland, as
cheep and reachable resources to sequestrate the carbon dioxide,
increases after the Industrial Revolution. Rangelands comprise the
large parts of Iran as a steppic area. Rudshur (Saveh), as area index of
steppic area, was selected under three sites include long-term
exclosure, medium-term exclosure, and grazable area in order to the
capable of carbon dioxide’s sequestration of dominated species.
Canopy cover’s percentage of two dominated species (Artemisia
sieberi Besser & Stipa barbata Desf) was determined via establishing
of random 1 square meter plot. The sampling of above and below
ground biomass style was obtained by complete random. After
determination of ash percentage in the laboratory; conversion ratio of
plant biomass to organic carbon was calculated by ignition method.
Results of the paired t-test showed that the amount of carbon
sequestration in above ground and underground biomass of Artemisia
sieberi Besser & Stipa barbata Desf is different in three regions. It,
of course, hasn’t any difference between under and surface ground’s
biomass of Artemisia sieberi Besser in long-term exclosure. The
independent t-test results indicate differences between underground
biomass corresponding each other in the studied sites. Carbon
sequestration in the Stipa barbata Desf was totally more than
Artemisia sieberi Besser. Altogether, the average sequestration of the
long-term exclosure was 5.842gr/m², the medium-term exclosure was
4.115gr/m², and grazable area was 5.975gr/m² so that there isn’t
valuable statistical difference in term of total amount of carbon
sequestration to three sites.
Abstract: Sustainable development is highly dependent on the
implementation of environmental education programs, which has as
its ultimate goal to produce environmentally literate citizens that
undertake environmentally friendly actions. Efforts on environmental
education along past years are now perceived on the increase of
citizens awareness on European countries and, particularly, in
Portugal. However, we still have a lack of information on the
prevalence of specific behaviors that contributes to sustainability,
influenced by a new attitude toward the environment. The
determination of pro-environmental behaviors prevalence in higher
education students is an important approach to understand to which
extend the next leading generation is, in practice, committed with the
goals of sustainable development. Therefore, present study evaluates
the prevalence of a specific set of behaviors (water savings, energy
savings, environmental criteria on shopping, and mobility) on the
University of Madeira students and discusses their commitment with
sustainable development.
Abstract: The objective of this study was to develop and compare alternative prediction equations of lean meat proportion (LMP) of lamb carcasses. Forty (40) male lambs, 22 of Churra Galega Bragançana Portuguese local breed and 18 of Suffolk breed were used. Lambs were slaughtered, and carcasses weighed approximately 30 min later in order to obtain hot carcass weight (HCW). After cooling at 4º C for 24-h a set of seventeen carcass measurements was recorded. The left side of carcasses was dissected into muscle, subcutaneous fat, inter-muscular fat, bone, and remainder (major blood vessels, ligaments, tendons, and thick connective tissue sheets associated with muscles), and the LMP was evaluated as the dissected muscle percentage. Prediction equations of LMP were developed, and fitting quality was evaluated through the coefficient of determination of estimation (R2 e) and standard error of estimate (SEE). Models validation was performed by k-fold crossvalidation and the coefficient of determination of prediction (R2 p) and standard error of prediction (SEP) were computed. The BT2 measurement was the best single predictor and accounted for 37.8% of the LMP variation with a SEP of 2.30%. The prediction of LMP of lamb carcasses can be based simple models, using as predictors the HCW and one fat thickness measurement.
Abstract: In this study, solid phase micro-extraction (SPME)
was optimized to improve the sensitivity and accuracy in
formaldehyde determination for plywood panels. Further work has
been carried out to compare the newly developed technique with
existing method which reacts formaldehyde collected in desiccators
with acetyl acetone reagent (DC-AA). In SPME, formaldehyde was
first derivatized with O-(2,3,4,5,6 pentafluorobenzyl)-hydroxylamine
hydrochloride (PFBHA) and analysis was then performed by gas
chromatography in combination with mass spectrometry (GC-MS).
SPME data subjected to various wood species gave satisfactory
results, with relative standard deviations (RSDs) obtained in the
range of 3.1-10.3%. It was also well correlated with DC values,
giving a correlation coefficient, RSQ, of 0.959. The quantitative
analysis of formaldehyde by SPME was an alternative in wood
industry with great potential
Abstract: Tool wear and surface roughness prediction plays a
significant role in machining industry for proper planning and control
of machining parameters and optimization of cutting conditions. This
paper deals with developing an artificial neural network (ANN)
model as a function of cutting parameters in turning steel under
minimum quantity lubrication (MQL). A feed-forward
backpropagation network with twenty five hidden neurons has been
selected as the optimum network. The co-efficient of determination
(R2) between model predictions and experimental values are 0.9915,
0.9906, 0.9761 and 0.9627 in terms of VB, VM, VS and Ra
respectively. The results imply that the model can be used easily to
forecast tool wear and surface roughness in response to cutting
parameters.
Abstract: This study investigates the capacity of granular
activated carbon (GAC) for the storage of methane through the
equilibrium adsorption. An experimental apparatus consist of a dual
adsorption vessel was set up for the measurement of equilibrium
adsorption of methane on GAC using volumetric technique (pressure
decay). Experimental isotherms of methane adsorption were
determined by the measurement of equilibrium uptake of methane in
different pressures (0-50 bar) and temperatures (285.15-328.15°K).
The experimental data was fitted to Freundlich and Langmuir
equations to determine the model isotherm. The results show that the
experimental data is equally well fitted by the both model isotherms.
Using the experimental data obtained in different temperatures the
isosteric heat of methane adsorption was also calculated by the
Clausius-Clapeyron equation from the Sips isotherm model. Results
of isosteric heat of adsorption show that decreasing temperature or
increasing methane uptake by GAC decrease the isosteric heat of
methane adsorption.
Abstract: This work proposes an optical fiber system (OF) for
sensing various volatile organic compounds (VOCs) in human breath
for the diagnosis of some metabolic disorders as a non-invasive
methodology. The analyzed VOCs are alkanes (i.e., ethane, pentane,
heptane, octane, and decane), and aromatic compounds (i.e., benzene,
toluene, and styrene). The OF displays high analytical performance
since it provides near real-time responses, rapid analysis, and low
instrumentation costs, as well as it exhibits useful linear range and
detection limits; the developed OF sensor is also comparable to a
reference methodology (gas chromatography-mass spectrometry) for
the eight tested VOCs.