Abstract: Average temperatures worldwide are expected to
continue to rise. At the same time, major cities in developing
countries are becoming increasingly populated and polluted.
Governments are tasked with the problem of overheating and air
quality in residential buildings. This paper presents the development
of a model, which is able to estimate the occupant exposure
to extreme temperatures and high air pollution within domestic
buildings. Building physics simulations were performed using the
EnergyPlus building physics software. An accurate metamodel is
then formed by randomly sampling building input parameters and
training on the outputs of EnergyPlus simulations. Metamodels are
used to vastly reduce the amount of computation time required when
performing optimisation and sensitivity analyses. Neural Networks
(NNs) have been compared to a Radial Basis Function (RBF)
algorithm when forming a metamodel. These techniques were
implemented using the PyBrain and scikit-learn python libraries,
respectively. NNs are shown to perform around 15% better than RBFs
when estimating overheating and air pollution metrics modelled by
EnergyPlus.
Abstract: Value addition to agricultural produce is of possible
potential in reducing poverty, improving food security and
malnutrition, therefore the need to develop small and microenterprises
of sweet potato production. A study was carried out in Nigeria to determine the acceptability
of blends sweet potato (Ipomea batatas) and commodities yellow
maize (Zea mays), millet (Pennisetum glaucum), soybean (Glycine
max), bambara groundnut (Vigna subterranean), guinea corn
(Sorghum vulgare), wheat (Triticum aestivum), and roselle (Hibiscus
sabdariffa) through sensory evaluation. Sweet potato (Ipomea batatas) roots were processed using two
methods: oven and sun drying. The blends were also assessed in
terms of functional, chemical and color properties. Most acceptable blends include BAW (80:20 of sweet
potato/wheat), BBC (80:20 of sweet potato/guinea corn), AAB (60:40
of sweet potato/guinea corn), YTE (100% soybean), TYG (100%
sweet potato), KTN (100% wheat flour), XGP (80:20 of sweet
potato/soybean), XAX (60:40 of sweet potato/wheat), LSS (100%
Roselle), CHK (100% Guinea corn), and ABC (60:40% of sweet
potato/ yellow maize). In addition, carried out chemical analysis
revealed that sweet potato has high percentage of vitamins A and C,
potassium (K), manganese (Mn), calcium (Ca), magnesium (Mg) and
iron (Fe) and fibre content. There is also an increase of vitamin A and
Iron in the blended products.
Abstract: This study investigated the effects of thermal
treatment on Tualang honey sample in terms of honey colour and
heat-induced small metabolites. The heating process was carried out
in a temperature controlled water batch at 90oC for 4 hours. The
honey samples were put in cylinder tubes with the dimension of 1 cm
diameter and 10 cm length for homogenous heat transfer. The results
found that the thermal treatment produced not only
hydroxylmethylfurfural, but also other harmful substances such as
phthalic anhydride and radiolytic byproducts. The degradation of
honey protein was due to the detection of free amino acids such as
cysteine and phenylalanine in heat-treated honey samples. Sugar
dehydration was also occurred because fragmented di-galactose was
identified based on the presence of characteristic ions in the mass
fragmentation pattern. The honey colour was found getting darker as
the heating duration was increased up to 4 hours. Approximately, 60
mm PFund of increment was noticed for the honey colour with the
colour change rate of 14.8 mm PFund per hour. Based on the
principal component analysis, the score plot clearly shows that the
chemical profile of Tualang honey was significantly altered after 2
hours of heating at 90oC.
Abstract: In order to utilize results from global climate models,
dynamical and statistical downscaling techniques have been
developed. For dynamical downscaling, usually a limited area
numerical model is used, with associated high computational cost.
This research proposes dynamic equation for specific space-time
regional climate downscaling from the Educational Global Climate
Model (EdGCM) for Southeast Asia. The equation is for surface air
temperature. This equation provides downscaling values of surface
air temperature at any specific location and time without running a
regional climate model. In the proposed equations, surface air
temperature is approximated from ground temperature, sensible heat
flux and 2m wind speed. Results from the application of the equation
show that the errors from the proposed equations are less than the
errors for direct interpolation from EdGCM.
Abstract: Both steady and unsteady turbulent mixed convection
heat transfer in a 3D lid-driven enclosure, which has constant heat
flux on the middle of bottom wall and with isothermal moving
sidewalls, is reported in this paper for working fluid with Prandtl
number Pr = 0.71. The other walls are adiabatic and stationary. The
dimensionless parameters used in this research are Reynolds number,
Re = 5000, 10000 and 15000, and Richardson number, Ri = 1 and 10.
The simulations have been done by using different turbulent methods
such as RANS, URANS, and LES. The effects of using different k-ε
models such as standard, RNG and Realizable k-ε model are
investigated. Interesting behaviours of the thermal and flow fields
with changing the Re or Ri numbers are observed. Isotherm and
turbulent kinetic energy distributions and variation of local Nusselt
number at the hot bottom wall are studied as well. The local Nusselt
number is found increasing with increasing either Re or Ri number.
In addition, the turbulent kinetic energy is discernibly affected by
increasing Re number. Moreover, the LES results have shown good
ability of this method in predicting more detailed flow structures in
the cavity.
Abstract: A three-dimensional numerical simulation of flow
through mini and microchannels with designed roughness is
conducted here. The effect of the roughness height (surface
roughness), geometry, Reynolds number on the friction factor, and
Nusselt number is investigated. The study is carried out by
employing CFD software, CFX. Our work focuses on a water flow
inside a circular mini-channel of 1 mm and microchannels of 500 and
100 m in diameter. The speed entry varies from 0.1 m/s to 20 m/s.
The general trend can be observed that bigger sizes of roughness
element lead to higher flow resistance. It is found that the friction
factor increases in a nonlinear fashion with the increase in obstruction
height. Particularly, the effect of roughness can no longer be ignored
at relative roughness height higher than 3%. A significant increase in
Poiseuille number is detected for all configurations considered. The
same observation can be done for Nusselt number. The transition
zone between laminar and turbulent flow depends on the channel
diameter.
Abstract: The modelling of physical phenomena, such as the
earth’s free oscillations, the vibration of strings, the interaction of
atomic particles, or the steady state flow in a bar give rise to Sturm-
Liouville (SL) eigenvalue problems. The boundary applications of
some systems like the convection-diffusion equation, electromagnetic
and heat transfer problems requires the combination of Dirichlet and
Neumann boundary conditions. Hence, the incorporation of Robin
boundary condition in the analyses of Sturm-Liouville problem. This
paper deals with the computation of the eigenvalues and
eigenfunction of generalized Sturm-Liouville problems with Robin
boundary condition using the finite element method. Numerical
solution of classical Sturm–Liouville problem is presented. The
results show an agreement with the exact solution. High results
precision is achieved with higher number of elements.
Abstract: Unsteady flow and heat transfer from a circular
cylinder in cross-flow is studied numerically. The governing
equations are solved by using finite volume method. Reynolds
number varies in range of 50 to 200; in this range flow is considered
to be laminar and unsteady. Al2O3 nanoparticle with volume fraction
in range of 5% to 20% is added to pure water. Effects of adding
nanoparticle to pure water on lift and drag coefficient and Nusselt
number is presented. Addition of Al2O3 has inconsiderable effect on
the value of drags and lift coefficient. However, it has significant
effect on heat transfer; results show that heat transfer of Al2O3
nanofluid is about 9% to 36% higher than pure water.
Abstract: A theoretical study of a humidification
dehumidification solar desalination unit has been carried out to
increase understanding the effect of weather conditions on the unit
productivity. A humidification-dehumidification (HD) solar
desalination unit has been designed to provide fresh water for
population in remote arid areas. It consists of solar water collector
and air collector; to provide the hot water and air to the desalination
chamber. The desalination chamber is divided into humidification
and dehumidification towers. The circulation of air between the two
towers is maintained by the forced convection. A mathematical
model has been formulated, in which the thermodynamic relations
were used to study the flow, heat and mass transfer inside the
humidifier and dehumidifier. The present technique is performed in
order to increase the unit performance. Heat and mass balance has
been done and a set of governing equations has been solved using the
finite difference technique. The unit productivity has been calculated
along the working day during the summer and winter sessions and
has compared with the available experimental results. The average
accumulative productivity of the system in winter has been ranged
between 2.5 to 4 (kg/m2)/day, while the average summer productivity
has been found between 8 to 12 (kg/m2)/day.
Abstract: The research on thermoelectric has been a blooming field of research for the latest decade, owing to large amount of heat source available to be harvested, being eco-friendly and static in operation. This paper provides the performance of thermoelectric generator (TEG) with bulk material of bismuth telluride, Bi2Te3. Later, the performance of the TEGs is evaluated by considering attaching the TEGs on a plastic (polyethylene sheet) in contrast to the common method of attaching the TEGs on the metal surface.
Abstract: Broiler slaughter waste has become a major source of
pollution throughout the world. Utilization of broiler slaughter waste
by dry rendering process produced Rendered Chicken Oil (RCO), a
cheap raw material for biodiesel production and Carcass Meal a feed
ingredient for pets and fishes. Conversion of RCO into biodiesel may
open new vistas for generating wealth from waste besides controlling
the major havoc of environmental pollution. A two-step process to
convert RCO to good quality Biodiesel was invented. Acid catalysed
esterification of FFA followed by base catalysed transesterification of
triglycerides was carried out after meticulously standardizing the
methanol molar ratio, catalyst concentration, reaction temperature,
and reaction time to obtain the maximum biodiesel yield of 97.62%
and lowest glycerol yield of 6.96%. RCO biodiesel blend was tested
in a CRDI diesel engine. The results revealed that the blending of
commercial diesel with 20% RCO biodiesel (B20) lead to less engine
wear, a quieter engine and better fuel economy. The better lubricating
qualities of RCO B20 prevented over heating of engine, which
prolongs the engine life. RCO B20 can reduce the import of crude oil
and substantially reduce the engine emissions as proved by
significantly lower smoke levels, thus mitigating climatic changes.
Abstract: This research paper portrays a comparative analysis of
thermomechanical behaviour of Shielded Metal Arc Welding
(SMAW) and Gas Tungsten Arc Welding (GTAW) of low carbon
steel of AISI 1020 grade butt joints. The thermal history has been
obtained by experimental work. We have focused on temperature
dependent cooling rate as depicted by Adam’s two-dimensional
model. The effect of moving point heat source of SMAW and GTAW
on mechanical properties has been judged by optical and scanning
electron micrographs of different regions in weld joints. The
microhardness study has been carried to visualize the joint strength
due to formation of different phases.
Abstract: The increase of technogenic and natural accidents,
accompanied by air pollution, for example, by combustion products,
leads to the necessity of respiratory protection. This work is devoted to the development of a calorimetric method
and a device which allows investigating quickly the kinetics of
carbon dioxide sorption by chemisorbents on the base of potassium
superoxide in order to assess the protective properties of respiratory
protective closed circuit apparatus. The features of the traditional approach for determining the
sorption properties in a thin layer of chemisorbent are described, as
well as methods and devices, which can be used for the sorption
kinetics study. The authors developed an approach (as opposed to the traditional
approach) based on the power measurement of internal heat sources
in the chemisorbent layer. The emergence of the heat sources is a
result of exothermic reaction of carbon dioxide sorption. This
approach eliminates the necessity of chemical analysis of samples
and can significantly reduce the time and material expenses during
chemisorbents testing. Error of determining the volume fraction of adsorbed carbon
dioxide by the developed method does not exceed 12%. Taking into
account the efficiency of the method, we consider that it is a good
alternative to traditional methods of chemical analysis under the
assessment of the protection sorbents quality.
Abstract: A solar receiver is designed for operation under
extremely uneven heat flux distribution, cyclic weather, and cloud
transient cycle conditions, which can include large thermal stress and
even receiver failure. In this study, the effect of different oil velocity
on convection coefficient factor and impact of wind velocity on local
Nusselt number by Finite Volume Method will be analyzed. This
study is organized to give an overview of the numerical modeling
using a MATLAB software, as an accurate, time efficient and
economical way of analyzing the heat transfer trends over stationary
receiver tube for different Reynolds number. The results reveal when
oil velocity is below 0.33m/s, the value of convection coefficient is
negligible at low temperature. The numerical graphs indicate that
when oil velocity increases up to 1.2 m/s, heat convection coefficient
increases significantly. In fact, a reduction in oil velocity causes a
reduction in heat conduction through the glass envelope. In addition,
the different local Nusselt number is reduced when the wind blows
toward the concave side of the collector and it has a significant effect
on heat losses reduction through the glass envelope.
Abstract: Heat treatable aluminum alloys such as 7075 and
7055, because of high strength and low density, are used widely in
aircraft industry. For best mechanical properties, T6 heat treatment
has recommended for this regards, but this temper treatment is
sensitive to corrosion induced and Stress Corrosion Cracking (SCC)
damage. For improving this property, the over-aging treatment (T7)
applies to this alloy, but it decreases the mechanical properties up to
30 percent. Hence, to increase the mechanical properties, without any
remarkable decrease in SCC resistant, Retrogression and Re-Aging
(RRA) heat treatment is used. This treatment performs in a relatively
short time. In this paper, the RRA heat treatment was applied to 7055
aluminum alloy and then effect of RRA time on the mechanical
properties of 7055 has been investigated. The results show that the
40-minute time is suitable time for retrogression of 7055 aluminum
alloy and ultimate strength increases up to 625MPa.
Abstract: A Multi-dimensional computational fluid dynamics
(CFD) two-phase model was developed with the aim to simulate
the in-core coolant circuit of a pressurized heavy water reactor
(PHWR) of a commercial nuclear power plant (NPP). Due to the
fact that this PHWR is a Reactor Pressure Vessel type (RPV),
three-dimensional (3D) detailed modelling of the large reservoirs of
the RPV (the upper and lower plenums and the downcomer) were
coupled with an in-house finite volume one-dimensional (1D) code
in order to model the 451 coolant channels housing the nuclear fuel.
Regarding the 1D code, suitable empirical correlations for taking into
account the in-channel distributed (friction losses) and concentrated
(spacer grids, inlet and outlet throttles) pressure losses were used.
A local power distribution at each one of the coolant channels
was also taken into account. The heat transfer between the coolant
and the surrounding moderator was accurately calculated using a
two-dimensional theoretical model. The implementation of subcooled
boiling and condensation models in the 1D code along with the use
of functions for representing the thermal and dynamic properties of
the coolant and moderator (heavy water) allow to have estimations
of the in-core steam generation under nominal flow conditions for a
generic fission power distribution. The in-core mass flow distribution
results for steady state nominal conditions are in agreement with the
expected from design, thus getting a first assessment of the coupled
1/3D model. Results for nominal condition were compared with
those obtained with a previous 1/3D single-phase model getting more
realistic temperature patterns, also allowing visualize low values of
void fraction inside the upper plenum. It must be mentioned that the
current results were obtained by imposing prescribed fission power
functions from literature. Therefore, results are showed with the aim
of point out the potentiality of the developed model.
Abstract: This study presents experimental and optimization of
nanoparticle mass concentration and heat input based on the total
thermal resistance (Rth) of loop heat pipe (LHP), employed for PCCPU
cooling. In this study, silica nanoparticles (SiO2) in water with
particle mass concentration ranged from 0% (pure water) to 1% is
considered as the working fluid within the LHP. The experimental
design and optimization is accomplished by the design of
experimental tool, Response Surface Methodology (RSM). The
results show that the nanoparticle mass concentration and the heat
input have significant effect on the Rth of LHP. For a given heat
input, the Rth is found to decrease with the increase of the
nanoparticle mass concentration up to 0.5% and increased thereafter.
It is also found that the Rth is decreased when the heat input is
increased from 20W to 60W. The results are optimized with the
objective of minimizing the Rth, using Design-Expert software, and
the optimized nanoparticle mass concentration and heat input are
0.48% and 59.97W, respectively, the minimum thermal resistance
being 2.66 (ºC/W).
Abstract: The objective of the paper is a numerical study of heat
transfer between perforated metal plates and the surrounding air
flows. Different perforation structures can nowadays be found in
various industrial products. Besides improving the mechanical
properties, the perforations can intensify the heat transfer as well. The
heat transfer coefficient depends on a wide range of parameters such
as type of perforation, size, shape, flow properties of the surrounding
air etc. The paper was focused on three different perforation
structures which have been investigated from the point of the view of
the production in the previous studies. To determine the heat
coefficients and the Nusselt numbers, the numerical simulation
approach was adopted. The calculations were performed using the
OpenFOAM software. The three-dimensional, unstable, turbulent and
incompressible air flow around the perforated surface metal plate was
considered.
Abstract: The aim of the study is to improve the understanding
of latent and sensible thermal energy storage within a paraffin wax
media by an array of cylindrical tubes arranged both in in-line and
staggered layouts. An analytical and experimental study is carried out
in a horizontal shell-and-tube type system during melting process.
Pertamina paraffin-wax was used as a phase change material (PCM),
while the tubes are embedded in the PCM. From analytical study we
can obtain the useful information in designing a thermal energy
storage such as: the motion of interface, amount of material melted at
any time in the process, and the heat storage characteristic during
melting. The use of staggered tubes is proposed compared to in-line
layout in a heat exchanger as thermal storage. The experimental study
is used to verify the validity of the analytical predictions. From the
comparisons, the analytical and experimental data are in a good
agreement.
Abstract: In this study, we investigated numerically heat
transfer by mixed convection coupled to radiation in a square cavity;
the upper horizontal wall is movable. The purpose of this study is to
see the influence of the emissivity ε and the varying of the
Richardson number Ri on the variation of average Nusselt number
Nu. The vertical walls of the cavity are differentially heated, the left
wall is maintained at a uniform temperature higher than the right
wall, and the two horizontal walls are adiabatic. The finite volume
method is used for solving the dimensionless Governing Equations.
Emissivity values used in this study are ranged between 0 and 1, the
Richardson number in the range 0.1 to 10. The Rayleigh number is
fixed to Ra=104 and the Prandtl number is maintained constant
Pr=0.71. Streamlines, isothermal lines and the average Nusselt
number are presented according to the surface emissivity. The results
of this study show that the Richardson number Ri and emissivity ε
affect the average Nusselt number.