Abstract: Aluminum/Copper clad sheet has been fabricated using
asymmetric extrusion method, which caused severe shear deformation
between Al and Cu plate to easily bond to each other. Interfacial
microstructure and mechanical properties of Al/Cu clad were studied
by scanning electron microscope equipped with energy dispersive
X-ray detector, micro-hardness, and tension tests. The asymmetric
extrusion bonding was very effective to provide a good interface for
atoms diffusion during subsequent annealing. The strength of bonding
was higher with the increasing extrusion ratio.
Abstract: This paper introduces a low cost INS/GPS algorithm for
land vehicle navigation application. The data fusion process is done
with an extended Kalman filter in cascade configuration mode. In
order to perform numerical simulations, MATLAB software has been
developed. Loosely coupled configuration is considered. The results
obtained in this work demonstrate that a low-cost INS/GPS navigation
system is partially capable of meeting the performance requirements
for land vehicle navigation. The relative effectiveness of the kalman
filter implementation in integrated GPS/INS navigation algorithm is
highlighted. The paper also provides experimental results; field test
using a car is carried out.
Abstract: I/O workload is a critical and important factor to
analyze I/O pattern and file system performance. However tracing I/O
operations on the fly distributed parallel file system is non-trivial due
to collection overhead and a large volume of data. In this paper, we
design and implement a parallel file system logging method for high
performance computing using shared memory-based multi-layer
scheme. It minimizes the overhead with reduced logging operation
response time and provides efficient post-processing scheme through
shared memory. Separated logging server can collect sequential logs
from multiple clients in a cluster through packet communication.
Implementation and evaluation result shows low overhead and high
scalability of this architecture for high performance parallel logging
analysis.
Abstract: Aluminum salt that is generally presents as a solid
phase in the water purification sludge (WPS) can be dissolved,
recovering a liquid phase, by adding strong acid to the sludge solution.
According to the reaction kinetics, when reactant is in the form of
small particles with a large specific surface area, or when the reaction
temperature is high, the quantity of dissolved aluminum salt or
reaction rate, respectively are high. Therefore, in this investigation,
water purification sludge (WPS) solution was treated with ultrasonic
waves to break down the sludge, and different acids (1 N HCl and 1 N
H2SO4) were used to acidify it. Acid dosages that yielded the solution
pH of less than two were used. The results thus obtained indicate that
the quantity of dissolved aluminum in H2SO4-acidified solution
exceeded that in HCl-acidified solution. Additionally, ultrasonic
treatment increased the rate of dissolution of aluminum and the
amount dissolved. The quantity of aluminum dissolved at 60℃ was 1.5
to 2.0 times higher than that at 25℃.
Abstract: Graph transformation has recently become more and
more popular as a general visual modeling language to formally state
the dynamic semantics of the designed models. Especially, it is a
very natural formalism for languages which basically are graph (e.g.
UML). Using this technique, we present a highly understandable yet
precise approach to formally model and analyze the behavioral
semantics of UML 2.0 Activity diagrams. In our proposal, AGG is
used to design Activities, then using our previous approach to model
checking graph transformation systems, designers can verify and
analyze designed Activity diagrams by checking the interesting
properties as combination of graph rules and LTL (Linear Temporal
Logic) formulas on the Activities.
Abstract: The motion of a sphere moving along the axis of a
rotating viscous fluid is studied at high Reynolds numbers and
moderate values of Taylor number. The Higher Order Compact
Scheme is used to solve the governing Navier-Stokes equations. The
equations are written in the form of Stream function, Vorticity
function and angular velocity which are highly non-linear, coupled
and elliptic partial differential equations. The flow is governed by
two parameters Reynolds number (Re) and Taylor number (T). For
very low values of Re and T, the results agree with the available
experimental and theoretical results in the literature. The results are
obtained at higher values of Re and moderate values of T and
compared with the experimental results. The results are fourth order
accurate.
Abstract: Carbon steel is used in boilers, pressure vessels, heat
exchangers, piping, structural elements and other moderatetemperature
service systems in which good strength and ductility are
desired. ASME Boiler and Pressure Vessel Code, Section II Part A
(2004) provides specifications of ferrous materials for construction of
pressure equipment, covering wide range of mechanical properties
including high strength materials for power plants application.
However, increased level of springback is one of the major problems
in fabricating components of high strength steel using bending.
Presented work discuss the springback simulations for five different
steels (i.e. SA-36, SA-299, SA-515 grade 70, SA-612 and SA-724
grade B) using finite element analysis of air V-bending. Analytical
springback simulations of hypothetical layered materials are
presented. Result shows that; (i) combination of the material property
parameters controls the springback, (ii) layer of the high ductility
steel on the high strength steel greatly suppresses the springback.
Abstract: In online context, the design and implementation of
effective remote laboratories environment is highly challenging on
account of hardware and software needs. This paper presents the
remote laboratory software framework modified from ilab shared
architecture (ISA). The ISA is a framework which enables students to
remotely acccess and control experimental hardware using internet
infrastructure. The need for remote laboratories came after
experiencing problems imposed by traditional laboratories. Among
them are: the high cost of laboratory equipment, scarcity of space,
scarcity of technical personnel along with the restricted university
budget creates a significant bottleneck on building required
laboratory experiments. The solution to these problems is to build
web-accessible laboratories. Remote laboratories allow students and
educators to interact with real laboratory equipment located
anywhere in the world at anytime. Recently, many universities and
other educational institutions especially in third world countries rely
on simulations because they do not afford the experimental
equipment they require to their students. Remote laboratories enable
users to get real data from real-time hand-on experiments. To
implement many remote laboratories, the system architecture should
be flexible, understandable and easy to implement, so that different
laboratories with different hardware can be deployed easily. The
modifications were made to enable developers to add more
equipment in ISA framework and to attract the new developers to
develop many online laboratories.
Abstract: The article contains results of the flour and bread
quality assessment from the grains of spring spelt, also called as an
ancient wheat. Spelt was cultivated on heavy and medium soils
observing principles of organic farming. Based on flour and bread
laboratory studies, as well as laboratory baking, the technological
usefulness of studied flour has been determined. These results were
referred to the standard derived from common wheat cultivated in the
same conditions. Grain of spring spelt is a good raw material for
manufacturing bread flour, from which to get high-quality bakery
products, but this is strictly dependent on the variety of ancient
wheat.
Abstract: Tubular process equipment is often damaged in
industrial processes. The damage occurs both on devices working at
high temperatures and also on less exposed devices. In case of sudden
damage of key equipment a shutdown of the whole production unit
and resulting significant economic losses are imminent. This paper
presents a solution of several types of tubular process equipment. The
causes of damage and suggestions of correction actions are discussed
in all cases. Very important part is the analysis of operational
conditions, determination of unfavourable working states decreasing
lifetime of devices and suggestions of correction actions. Lately very
popular numerical methods are used for analysis of the equipment.
Abstract: One of the essential components of much of DSP
application is noise cancellation. Changes in real time signals are
quite rapid and swift. In noise cancellation, a reference signal which
is an approximation of noise signal (that corrupts the original
information signal) is obtained and then subtracted from the noise
bearing signal to obtain a noise free signal. This approximation of
noise signal is obtained through adaptive filters which are self
adjusting. As the changes in real time signals are abrupt, this needs
adaptive algorithm that converges fast and is stable. Least mean
square (LMS) and normalized LMS (NLMS) are two widely used
algorithms because of their plainness in calculations and
implementation. But their convergence rates are small. Adaptive
averaging filters (AFA) are also used because they have high
convergence, but they are less stable. This paper provides the
comparative study of LMS and Normalized NLMS, AFA and new
enhanced average adaptive (Average NLMS-ANLMS) filters for noise
cancelling application using speech signals.
Abstract: Performing High Voltage (HV) tasks with a multi craft
work force create a special set of safety circumstances. This paper
aims to present vital information relating to when it is acceptable to
use a single or a two-layer soil structure. Also it discusses the
implication of the high voltage infrastructure on the earth grid and the
safety of this implication under a single or a two-layer soil structure.
A multiple case study is investigated to show the importance of using
the right soil resistivity structure during the earthing system design.
Abstract: A process flowsheet was developed in ChemCad 6.4
to study the effect of feed moisture contents on the pre-esterification
of waste oils. Waste oils were modelled as a mixture of triolein
(90%), oleic acid (5%) and water (5%). The process mainly consisted
of feed drying, pre-esterification reaction and methanol recovery. The
results showed that the process energy requirements would be
minimized when higher degrees of feed drying and higher preesterification
reaction temperatures are used.
Abstract: In general dynamic analyses, lower mode response is
of interest, however the higher modes of spatially discretized
equations generally do not represent the real behavior and not affects
to global response much. Some implicit algorithms, therefore, are
introduced to filter out the high-frequency modes using intended
numerical error. The objective of this study is to introduce the
P-method and PC α-method to compare that with dissipation method
and Newmark method through the stability analysis and numerical
example. PC α-method gives more accuracy than other methods
because it based on the α-method inherits the superior properties of the
implicit α-method. In finite element analysis, the PC α-method is more
useful than other methods because it is the explicit scheme and it
achieves the second order accuracy and numerical damping
simultaneously.
Abstract: Soursop (Anona muricata) is one of the underutilized tropical fruits containing nutrients, particularly dietary fibre and antioxidant properties that are beneficial to human health. This objective of this study is to investigate the feasibility of matured soursop pulp flour (SPF) to be substituted with high-protein wheat flour in bread. Bread formulation was substituted with different levels of SPF (0%, 5%, 10% and 15%). The effect on physicochemical properties and sensory attributes were evaluated. Higher substitution level of SPF resulted in significantly higher (p
Abstract: The aim of this paper is to introduce a parametric
distribution model in fatigue life reliability analysis dealing with
variation in material properties. Service loads in terms of responsetime
history signal of Belgian pave were replicated on a multi-axial
spindle coupled road simulator and stress-life method was used to
estimate the fatigue life of automotive stub axle. A PSN curve was
obtained by monotonic tension test and two-parameter Weibull
distribution function was used to acquire the mean life of the
component. A Pearson system was developed to evaluate the fatigue
life reliability by considering stress range intercept and slope of the
PSN curve as random variables. Considering normal distribution of
fatigue strength, it is found that the fatigue life of the stub axle to
have the highest reliability between 10000 – 15000 cycles. Taking
into account the variation of material properties associated with the
size effect, machining and manufacturing conditions, the method
described in this study can be effectively applied in determination of
probability of failure of mass-produced parts.
Abstract: Pulse code modulation is a widespread technique
in digital communication with significant impact on existing
modern and proposed future communication technologies. Its
widespread utilization is due to its simplicity and attractive
spectral characteristics. In this paper, we present a new
approach to the spectral analysis of PCM signals using
Riemann-Stieltjes integrals, which is very accurate for high bit
rates. This approach can serve as a model for similar spectral
analysis of other competing modulation schemes.
Abstract: Simulations play a major role in education not only because they provide realistic models with which students can interact to acquire real world experiences, but also because they constitute safe environments in which students can repeat processes without any risk in order to perceive easier concepts and theories. Virtual reality is widely recognized as a significant technological advance that can facilitate learning process through the development of highly realistic 3D simulations supporting immersive and interactive features. The objective of this paper is to analyze the influence of virtual reality-s use in chemistry instruction as well as to present an integrated web-based learning environment for the simulation of chemical experiments. The proposed application constitutes a cost-effective solution for both schools and universities without appropriate infrastructure and a valuable tool for distance learning and life-long education in chemistry. Its educational objectives are the familiarization of students with the equipment of a real chemical laboratory and the execution of virtual volumetric analysis experiments with the active participation of students.
Abstract: Music Information Retrieval (MIR) and modern data mining techniques are applied to identify style markers in midi music for stylometric analysis and author attribution. Over 100 attributes are extracted from a library of 2830 songs then mined using supervised learning data mining techniques. Two attributes are identified that provide high informational gain. These attributes are then used as style markers to predict authorship. Using these style markers the authors are able to correctly distinguish songs written by the Beatles from those that were not with a precision and accuracy of over 98 per cent. The identification of these style markers as well as the architecture for this research provides a foundation for future research in musical stylometry.
Abstract: High level and high velocity flood flows are
potentially harmful to bridge piers as evidenced in many toppled
piers, and among them the single-column piers were considered as
the most vulnerable. The flood flow characteristic parameters
including drag coefficient, scouring and vortex shedding are built into
a pier-flood interaction model to investigate structural safety against
flood hazards considering the effects of local scouring, hydrodynamic
forces, and vortex induced resonance vibrations. By extracting the
pier-flood simulation results embedded in a neural networks code,
two cases of pier toppling occurred in typhoon days were reexamined:
(1) a bridge overcome by flash flood near a mountain side;
(2) a bridge washed off in flood across a wide channel near the
estuary. The modeling procedures and simulations are capable of
identifying the probable causes for the tumbled bridge piers during
heavy floods, which include the excessive pier bending moments and
resonance in structural vibrations.