Abstract: Optimal capacitor allocation in distribution systems
has been studied for a long times. It is an optimization problem
which has an objective to define the optimal sizes and locations of
capacitors to be installed. In this works, an overview of capacitor
placement problem in distribution systems is briefly introduced. The
objective functions and constraints of the problem are listed and the
methodologies for solving the problem are summarized.
Abstract: The Influence Diagrams (IDs) is a kind of Probabilistic Belief Networks for graphic modeling. The usage of IDs can improve the communication among field experts, modelers, and decision makers, by showing the issue frame discussed from a high-level point of view. This paper enhances the Time-Sliced Influence Diagrams (TSIDs, or called Dynamic IDs) based formalism from a Discrete Event Systems Modeling and Simulation (DES M&S) perspective, for Exploring Analysis (EA) modeling. The enhancements enable a modeler to specify times occurred of endogenous events dynamically with stochastic sampling as model running and to describe the inter- influences among them with variable nodes in a dynamic situation that the existing TSIDs fails to capture. The new class of model is named Dynamic-Stochastic Influence Diagrams (DSIDs). The paper includes a description of the modeling formalism and the hiberarchy simulators implementing its simulation algorithm, and shows a case study to illustrate its enhancements.
Abstract: In this study, stress distributions on dental implants
made of functionally graded biomaterials (FGBM) are investigated
numerically. The implant body is considered to be subjected to axial
compression loads. Numerical problem is assumed to be 2D, and
ANSYS commercial software is used for the analysis. The cross
section of the implant thread varies as varying the height (H) and the
width (t) of the thread. According to thread dimensions of implant
and material properties of FGBM, equivalent stress distribution on
the implant is determined and presented with contour plots along
with the maximum equivalent stress values. As a result, with
increasing material gradient parameter (n), the equivalent stress
decreases, but the minimum stress distribution increases. Maximum
stress values decrease with decreasing implant radius (r). Maximum
von Mises stresses increases with decreasing H when t is constant.
On the other hand, the stress values are not affected by variation of t
in the case of H = constant.
Abstract: The design of weight is one of the important parts in
fuzzy decision making, as it would have a deep effect on the evaluation
results. Entropy is one of the weight measure based on objective
evaluation. Non--probabilistic-type entropy measures for fuzzy set
and interval type-2 fuzzy sets (IT2FS) have been developed and applied
to weight measure. Since the entropy for (IT2FS) for decision
making yet to be explored, this paper proposes a new objective
weight method by using entropy weight method for multiple attribute
decision making (MADM). This paper utilizes the nature of IT2FS
concept in the evaluation process to assess the attribute weight based
on the credibility of data. An example was presented to demonstrate
the feasibility of the new method in decision making. The entropy
measure of interval type-2 fuzzy sets yield flexible judgment and
could be applied in decision making environment.
Abstract: In the present work homogeneous silica film on
silicon was fabricated by colloidal silica sol. The silica sol precursor
with uniformly granular particle was derived by the alkaline
hydrolysis of tetraethoxyorthosilicate (TEOS) in presence of glycerol
template. The film was prepared by dip coating process. The
templated hetero-structured silica film was annealed at elevated
temperatures to generate nano- and meso porosity in the film. The
film was subsequently annealed at different temperatures to make it
defect free and abrasion resistant. The sol and the film were
characterized by the measurement of particle size distribution,
scanning electron microscopy, XRD, FTIR spectroscopy,
transmission electron microscopy, atomic force microscopy,
measurement of the refractive index, thermal conductivity and
abrasion resistance. The porosity of the films decreased whereas
refractive index and dielectric constant of it `increased with the
increase in the annealing temperature. The thermal conductivity of
the films increased with the increase in the film thickness. The
developed porous silica film holds strong potential for use in
different areas.
Abstract: Combustion of sprays is of technological importance, but its flame behavior is not fully understood. Furthermore, the multiplicity of dependent variables such as pressure, temperature, equivalence ratio, and droplet sizes complicates the study of spray combustion. Fundamental study on the influence of the presence of liquid droplets has revealed that laminar flames within aerosol mixtures more readily become unstable than for gaseous ones and this increases the practical burning rate. However, fundamental studies on turbulent flames of aerosol mixtures are limited particularly those under near mono-dispersed droplet conditions. In the present work, centrally ignited expanding flames at near atmospheric pressures are employed to quantify the burning rates in gaseous and aerosol flames. Iso-octane-air aerosols are generated by expansion of the gaseous pre-mixture to produce a homogeneously distributed suspension of fuel droplets. The effects of the presence of droplets and turbulence velocity in relation to the burning rates of the flame are also investigated.
Abstract: Wetting characteristics of reactive (Sn–0.7Cu solder)
and non– reactive (castor oil) wetting of liquids on Cu and Ag plated
Al substrates have been investigated. Solder spreading exhibited
capillary, gravity and viscous regimes. Oils did not exhibit noticeable
spreading regimes. Solder alloy showed better wettability on Ag
coated Al substrate compared to Cu plating. In the case of castor oil,
Cu coated Al substrate exhibited good wettability as compared to Ag
coated Al substrates. The difference in wettability during reactive
wetting of solder and non–reactive wetting of oils is attributed to the
change in the surface energies of Al substrates brought about by the
formation of intermetallic compounds (IMCs).
Abstract: Leptospirosis is recognized as an important zoonosis
in tropical regions well as an important animal disease with
substantial loss in production. In this study, the model for the
transmission of the Leptospirosis disease to human population are
discussed. Model is described the vector population dynamics and
the Leptospirosis transmission to the human population are
discussed. Local analysis of equilibria are given. We confirm the
results by using numerical results.
Abstract: Large volumes of fingerprints are collected and stored
every day in a wide range of applications, including forensics, access
control etc. It is evident from the database of Federal Bureau of
Investigation (FBI) which contains more than 70 million finger
prints. Compression of this database is very important because of this
high Volume. The performance of existing image coding standards
generally degrades at low bit-rates because of the underlying block
based Discrete Cosine Transform (DCT) scheme. Over the past
decade, the success of wavelets in solving many different problems
has contributed to its unprecedented popularity. Due to
implementation constraints scalar wavelets do not posses all the
properties which are needed for better performance in compression.
New class of wavelets called 'Multiwavelets' which posses more
than one scaling filters overcomes this problem. The objective of this
paper is to develop an efficient compression scheme and to obtain
better quality and higher compression ratio through multiwavelet
transform and embedded coding of multiwavelet coefficients through
Set Partitioning In Hierarchical Trees algorithm (SPIHT) algorithm.
A comparison of the best known multiwavelets is made to the best
known scalar wavelets. Both quantitative and qualitative measures of
performance are examined for Fingerprints.
Abstract: This paper provides a key driver-based conceptual framework that can be used to improve a firm-s success in commercializing technology and in new product innovation resulting from collaboration with other organizations through strategic alliances. Based on a qualitative study using an interview approach, strategic alliances of entrepreneurs in the food processing industry in Thailand are explored. This paper describes factors affecting decisions to collaborate through alliances. It identifies four issues: maintaining the efficiency of the value chain for production capability, adapting to present and future competition, careful assessment of value of outcomes, and management of innovation. We consider five driving factors: resource orientation, assessment of risk, business opportunity, sharing of benefits and confidence in alliance partners. These factors will be of interest to entrepreneurs and policy makers with regard to further understanding of the direction of business strategies.
Abstract: In this research, heat transfer of a poly Ethylene
fluidized bed reactor without reaction were studied experimentally
and computationally at different superficial gas velocities. A multifluid
Eulerian computational model incorporating the kinetic theory
for solid particles was developed and used to simulate the heat
conducting gas–solid flows in a fluidized bed configuration.
Momentum exchange coefficients were evaluated using the Syamlal–
O-Brien drag functions. Temperature distributions of different phases
in the reactor were also computed. Good agreement was found
between the model predictions and the experimentally obtained data
for the bed expansion ratio as well as the qualitative gas–solid flow
patterns. The simulation and experimental results showed that the gas
temperature decreases as it moves upward in the reactor, while the
solid particle temperature increases. Pressure drop and temperature
distribution predicted by the simulations were in good agreement
with the experimental measurements at superficial gas velocities
higher than the minimum fluidization velocity. Also, the predicted
time-average local voidage profiles were in reasonable agreement
with the experimental results. The study showed that the
computational model was capable of predicting the heat transfer and
the hydrodynamic behavior of gas-solid fluidized bed flows with
reasonable accuracy.
Abstract: The objectives of this research paper were to study the
influencing factors that contributed to the success of electronic
commerce (e-commerce) and to study the approach to enhance the
standard of e-commerce for small and medium enterprises (SME).
The research paper focused the study on only sole proprietorship
SMEs in Bangkok, Thailand. The factors contributed to the success
of SME included business management, learning in the organization,
business collaboration, and the quality of website. A quantitative and
qualitative mixed research methodology was used. In terms of
quantitative method, a questionnaire was used to collect data from
251 sole proprietorships. The System Equation Model (SEM) was
utilized as the tool for data analysis. In terms of qualitative method,
an in-depth interview, a dialogue with experts in the field of ecommerce
for SMEs, and content analysis were used.
By using the adjusted causal relationship structure model, it was
revealed that the factors affecting the success of e-commerce for
SMEs were found to be congruent with the empirical data. The
hypothesis testing indicated that business management influenced the
learning in the organization, the learning in the organization
influenced business collaboration and the quality of the website, and
these factors, in turn, influenced the success of SMEs. Moreover, the
approach to enhance the standard of SMEs revealed that the majority
of respondents wanted to enhance the standard of SMEs to a high
level in the category of safety of e-commerce system, basic structure
of e-commerce, development of staff potentials, assistance of budget
and tax reduction, and law improvement regarding the e-commerce
respectively.
Abstract: The aim of this study is to show innovative techniques that describe the effectiveness of individuals diagnosed with antisocial personality disorders (ASPD). The author presents information about hate schemas regarding persons with ASPD and their understanding of the role of hate. The data of 60 prisoners with ASPD, 40 prisoners without ASPD, and 60 men without antisocial tendencies, has been analyzed. The participants were asked to describe their hate inspired by a photograph. The narrative discourse was analyzed, the three groups were compared. The results show the differences between the inmates with ASPD, those without ASPD, and the controls. The antisocial individuals describe hate as an ambivalent feeling with low emotional intensity, i.e., actors (in stories) are presented more as positives than as partners. They use different mechanisms to keep them from understanding the meaning of the emotional situation. The schema's characteristics were expressed in narratives attributed to high Psychopathy.
Abstract: A new fuzzy filter is presented for noise reduction of
images corrupted with additive noise. The filter consists of two
stages. In the first stage, all the pixels of image are processed for
determining noisy pixels. For this, a fuzzy rule based system
associates a degree to each pixel. The degree of a pixel is a real
number in the range [0,1], which denotes a probability that the pixel
is not considered as a noisy pixel. In the second stage, another fuzzy
rule based system is employed. It uses the output of the previous
fuzzy system to perform fuzzy smoothing by weighting the
contributions of neighboring pixel values. Experimental results are
obtained to show the feasibility of the proposed filter. These results
are also compared to other filters by numerical measure and visual
inspection.
Abstract: This work is focused on the steady boundary layer flow
near the forward stagnation point of plane and axisymmetric bodies
towards a stretching sheet. The no slip condition on the solid
boundary is replaced by the partial slip condition. The analytical
solutions for the velocity distributions are obtained for the various
values of the ratio of free stream velocity and stretching velocity, slip
parameter, the suction and injection velocity parameter, magnetic
parameter and dimensionality index parameter in the series forms with
the help of homotopy analysis method (HAM). Convergence of the
series is explicitly discussed. Results show that the flow and the skin
friction coefficient depend heavily on the velocity slip factor. In
addition, the effects of all the parameters mentioned above were more
pronounced for plane flows than for axisymmetric flows.
Abstract: The reliability of the tools developed to learn the
learning styles is essential to find out students- learning styles
trustworthily. For this purpose, the psychometric features of Grasha-
Riechman Student Learning Style Inventory developed by Grasha
was studied to contribute to this field. The study was carried out on
6th, 7th, and 8th graders of 10 primary education schools in Konya.
The inventory was applied twice with an interval of one month, and
according to the data of this application, the reliability coefficient
numbers of the 6 sub-dimensions pointed in the theory of the
inventory was found to be medium. Besides, it was found that the
inventory does not have a structure with 6 factors for both
Mathematics and English courses as represented in the theory.
Abstract: This study was aimed to explain the influence of surface roughness of the drawbead on non-symmetry deep drawing cold rolled steel sheet to improve the drawability of cold rolled steel sheet. The variables used in this study included semi-circle drawbead with 3 levels of surface roughness which are 6.127 mm Ra, 0.963 mm Ra and 0.152 mm Ra and cold rolled steel sheet according to 3 grades of the JIS standards which are SPCC, SPCE and SPCD with the thickness of 1.0 mm and the blankholder force which is 50% of the drawing force and the depth of 50 mm. According to the test results, when there was the increase in the surface roughness of drawbead, there would be the increase in deep drawing force, especially the SPCC cold rolled steel sheet. This is similar to the increase in the equivalent strain and the wall thickness distribution when the surface roughness of the drawbead increased. It could be concluded that the surface roughness of drawbead has an influence on deep drawing cold rolled steel sheet, especially the drawing force, the equivalent strain and the wall thickness distribution.
Abstract: This study investigates the relationships between
Work Motivation, Work Stress, and Job Satisfaction toward
cross-strait employees. The target subjects are three
manufacturing firms in Mainland China and Taiwan. Out of 450
distributed surveys, 352 valid surveys were obtained with the
response rate of 78.22%.The findings have addressed three main
pull factors toward cross-strait employees in choosing jobs, which
are (1) high level of firm stability, (2) good firm image, and (3)
good employee benefits. In addition, various employee attributes
exert different impacts on Work Motivation, Work Stress, and
Job Satisfaction. The comparison between expected and actual
perceived Job Satisfaction toward cross-strait employees shows
that “salary" ranks highest regarding expected Job Satisfaction
whereas “co-worker relationship" ranks highest regarding actual
perceived Job Satisfaction, which implies actual perceived Job
Satisfaction do not match employee expectations. Therefore, this
research further concludes that there exists differences between
employees- expected and actual perceived Job Satisfaction.
Abstract: This paper presents a new technique for the optimum
placement of processors to minimize the total effective
communication load under multi-processor communication
dominated environment. This is achieved by placing heavily loaded
processors near each other and lightly loaded ones far away from
one another in the physical grid locations. The results are
mathematically proved for the Algorithms are described.
Abstract: The security of power systems against malicious cyberphysical
data attacks becomes an important issue. The adversary
always attempts to manipulate the information structure of the power
system and inject malicious data to deviate state variables while
evading the existing detection techniques based on residual test. The
solutions proposed in the literature are capable of immunizing the
power system against false data injection but they might be too costly
and physically not practical in the expansive distribution network.
To this end, we define an algebraic condition for trustworthy power
system to evade malicious data injection. The proposed protection
scheme secures the power system by deterministically reconfiguring
the information structure and corresponding residual test. More
importantly, it does not require any physical effort in either microgrid
or network level. The identification scheme of finding meters being
attacked is proposed as well. Eventually, a well-known IEEE 30-bus
system is adopted to demonstrate the effectiveness of the proposed
schemes.