Abstract: Organic Rankine Cycle (ORC) is the most commonly used method for recovering energy from small sources of heat. The investigation of the ORC in supercritical condition is a new research area as it has a potential to generate high power and thermal efficiency in a waste heat recovery system. This paper presents a steady state ORC model in supercritical condition and its simulations with a real engine’s exhaust data. The key component of ORC, evaporator, is modelled using finite volume method, modelling of all other components of the waste heat recovery system such as pump, expander and condenser are also presented. The aim of this paper is to investigate the effects of mass flow rate and evaporator outlet temperature on the efficiency of the waste heat recovery process. Additionally, the necessity of maintaining an optimum evaporator outlet temperature is also investigated. Simulation results show that modification of mass flow rate is the key to changing the operating temperature at the evaporator outlet.
Abstract: The Blue Nile Basin is the most important tributary of
the Nile River. Egypt and Sudan are almost dependent on water
originated from the Blue Nile. This multi-dependency creates
conflicts among the three countries Egypt, Sudan, and Ethiopia
making the management of these conflicts as an international issue.
Good assessment of the water resources of the Blue Nile is an
important to help in managing such conflicts. Hydrological models
are good tool for such assessment. This paper presents a critical
review of the nature and variability of the climate and hydrology of
the Blue Nile Basin as a first step of using hydrological modeling to
assess the water resources of the Blue Nile. Many several attempts
are done to develop basin-scale hydrological modeling on the Blue
Nile. Lumped and semi distributed models used averages of
meteorological inputs and watershed characteristics in hydrological
simulation, to analyze runoff for flood control and water resource
management. Distributed models include the temporal and spatial
variability of catchment conditions and meteorological inputs to
allow better representation of the hydrological process. The main
challenge of all used models was to assess the water resources of the
basin is the shortage of the data needed for models calibration and
validation. It is recommended to use distributed model for their
higher accuracy to cope with the great variability and complexity of
the Blue Nile basin and to collect sufficient data to have more
sophisticated and accurate hydrological modeling.
Abstract: This article discusses issues related to the System of
Innovation: Comparing economies of Brazil and South Africa.
Having as this study aimed at comparing the Innovation System of
the countries mentioned. Then briefly describe the process of Venture
Capital and present the industry innovation in Brazil and South
Africa. The methodological approach described in this article is
descriptive and the approach is qualitative, taking as a basis
secondary data relating to research articles. The main results are
related to the different forms of financing of Venture Capital used by
countries compared, in addition to the training and economic policy.
And finally, it was highlighted the importance of implementation of
policy reforms for the Brazil and Africa in the innovation process.
Abstract: This study investigates the cleaning performance of
high intensity 360 kHz frequency on removal of nano-dimensional
and sub-micron particles from various surfaces, uniformity of the
cleaning tank and run to run variation of cleaning process. The
uniformity of the cleaning tank was measured by two different
methods i.e. 1. ppbTM meter and 2. Liquid Particle Counting (LPC)
technique. The result indicates that the energy was distributed more
uniformly throughout the entire cleaning vessel even at the corners
and edges of the tank when megasonic sweeping technology is
applied. The result also shows that rinsing the parts with 360 kHz
frequency at final rinse gives lower particle counts, hence higher
cleaning efficiency as compared to other frequencies. When
megasonic sweeping technology is applied each piezoelectric
transducers will operate at their optimum resonant frequency and
generates stronger acoustic cavitational force and higher acoustic
streaming velocity. These combined forces are helping to enhance the
particle removal and at the same time improve the overall cleaning
performance. The multiple extractions study was also carried out for
various frequencies to measure the cleaning potential and asymptote
value.
Abstract: The characteristic requirement for producing
rectangular shape bottles was a uniform thickness of the plastic bottle
wall. Die shaping was a good technique which controlled the wall
thickness of bottles. An advance technology which was the finite
element method (FEM) for blowing parison to be a rectangular shape
bottle was conducted to reduce waste plastic from a trial and error
method of a die shaping and parison control method. The artificial
intelligent (AI) comprised of artificial neural network and genetic
algorithm was selected to optimize the die gap shape from the FEM
results. The application of AI technique could optimize the suitable
die gap shape for the parison blow molding which did not depend on
the parison control method to produce rectangular bottles with the
uniform wall. Particularly, this application can be used with cheap
blow molding machines without a parison controller therefore it will
reduce cost of production in the bottle blow molding process.
Abstract: The web’s increased popularity has included a huge
amount of information, due to which automated web page
classification systems are essential to improve search engines’
performance. Web pages have many features like HTML or XML
tags, hyperlinks, URLs and text contents which can be considered
during an automated classification process. It is known that Webpage
classification is enhanced by hyperlinks as it reflects Web page
linkages. The aim of this study is to reduce the number of features to
be used to improve the accuracy of the classification of web pages. In
this paper, a novel feature selection method using an improved
Particle Swarm Optimization (PSO) using principle of evolution is
proposed. The extracted features were tested on the WebKB dataset
using a parallel Neural Network to reduce the computational cost.
Abstract: Environmental impact assessment techniques have
been developed as a result of the worldwide efforts to reduce the
environmental impact of global warming. By using the quantification
method in the construction industry, it is now possible to manage the
greenhouse gas is to systematically evaluate the impact on the
environment over the entire construction process. In particular, the
proportion of greenhouse gas emissions at the production stage of
construction material occupied is high, and efforts are needed in
particular in the construction field.
In this research, intended for concrete products for the construction
materials, by using the LCA method, we compared the results of
environmental impact assessment and carbon emissions of developing
products that have been applied low-carbon technologies compared to
existing products. As a results, by introducing a raw material of
industrial waste, showed carbon reduction. Through a comparison of
the carbon emission reduction effect of low carbon technologies, it is
intended to provide academic data for the evaluation of greenhouse
gases in the construction sector and the development of low carbon
technologies of the future.
Abstract: The purpose of this paper is to examine the hypothesis
explaining the mechanism in the case, where the product is deleted or
reduced the fundamental function of the product through the product
concept changes in the digital camera industry. This paper points out
not owning the fundamental technology might cause the change of the
product concept. Casio could create new competitive factor so that this
paper discusses a possibility of the mechanism of changing the product
concept.
Abstract: This paper presents an efficient fusion algorithm for
iris images to generate stable feature for recognition in unconstrained
environment. Recently, iris recognition systems are focused on real
scenarios in our daily life without the subject’s cooperation. Under
large variation in the environment, the objective of this paper is to
combine information from multiple images of the same iris. The
result of image fusion is a new image which is more stable for further
iris recognition than each original noise iris image. A wavelet-based
approach for multi-resolution image fusion is applied in the fusion
process. The detection of the iris image is based on Adaboost
algorithm and then local binary pattern (LBP) histogram is then
applied to texture classification with the weighting scheme.
Experiment showed that the generated features from the proposed
fusion algorithm can improve the performance for verification system
through iris recognition.
Abstract: Biofuels production has come forth as a future
technology to combat the problem of depleting fossil fuels. Bio-based
ethanol production from enzymatic lignocellulosic biomass
degradation serves an efficient method and catching the eye of
scientific community. High cost of the enzyme is the major obstacle
in preventing the commercialization of this process. Thus main
objective of the present study was to optimize composition of
medium components for enhancing cellulase production by newly
isolated strain of Bacillus tequilensis. Nineteen factors were taken
into account using statistical Plackett-Burman Design. The significant
variables influencing the cellulose production were further employed
in statistical Response Surface Methodology using Central
Composite Design for maximizing cellulase production. The
optimum medium composition for cellulase production was: peptone
(4.94 g/L), ammonium chloride (4.99 g/L), yeast extract (2.00 g/L),
Tween-20 (0.53 g/L), calcium chloride (0.20 g/L) and cobalt chloride
(0.60 g/L) with pH 7, agitation speed 150 rpm and 72 h incubation at
37oC. Analysis of variance (ANOVA) revealed high coefficient of
determination (R2) of 0.99. Maximum cellulase productivity of 11.5
IU/ml was observed against the model predicted value of 13 IU/ml.
This was found to be optimally active at 60oC and pH 5.5.
Abstract: The restrained construction zoning, an important part
in the urban master plan, is a necessary planning tool to control the city
sprawl, to guarantee the reservation implementation of the various
types of protective elements, and to realize the storage of the essential
urban spatial resources. Simultaneously, owing to the diverse
constitutes of restrained construction area and the various stakeholders
involved in, its planning requires an overall consideration of all
elements from the perspective of coordination+, balance and
practicability to deal with the problems and conflicts in this process.
Taking Yangzijin Ecological Restrained Construction Area in
Yangzhou as an example, this study analyzes all the potential actors,
agencies and stakeholders in this restrained construction area, as well
as the relevant conflicts between each other. Besides, this study tries to
build up a planning procedure based on the framework of governance
theory, and proposes a possible planning method that combines
"rigidity" and "flexibility" to protect the ecological limitation
boundary, to take every interest into account, and to promote economic
development in a harmonious society.
Abstract: Diffusion stills have been effective in water
desalination. The present work represents a model of the distillation
process by using vertical single-effect diffusion stills. A semianalytical
model has been developed to model the process. A
software computer code using Engineering Equation Solver EES
software has been developed to solve the equations of the developed
model. An experimental setup has been constructed, and used for the
validation of the model. The model is also validated against former
literature results. The results obtained from the present experimental
test rig, and the data from the literature, have been compared with the
results of the code to find its best range of validity. In addition, a
parametric analysis of the system has been developed using the
model to determine the effect of operating conditions on the system's
performance. The dominant parameters that affect the productivity of
the still are the hot plate temperature that ranges from (55- 90°C) and
feed flow rate in range of (0.00694-0.0211 kg/m2-s).
Abstract: A novel hybrid model of the lumbar spine, allowing
fast static and dynamic simulations of the disc pressure
and the spine mobility, is introduced in this work. Our
contribution is to combine rigid bodies, deformable finite
elements, articular constraints, and springs into a unique model
of the spine. Each vertebra is represented by a rigid body
controlling a surface mesh to model contacts on the facet
joints and the spinous process. The discs are modeled using
a heterogeneous tetrahedral finite element model. The facet
joints are represented as elastic joints with six degrees of
freedom, while the ligaments are modeled using non-linear
one-dimensional elastic elements. The challenge we tackle
is to make these different models efficiently interact while
respecting the principles of Anatomy and Mechanics.
The mobility, the intradiscal pressure, the facet joint force and
the instantaneous center of rotation of the lumbar spine are
validated against the experimental and theoretical results of
the literature on flexion, extension, lateral bending as well as
axial rotation.
Our hybrid model greatly simplifies the modeling task and
dramatically accelerates the simulation of pressure within the
discs, as well as the evaluation of the range of motion and the
instantaneous centers of rotation, without penalizing precision.
These results suggest that for some types of biomechanical
simulations, simplified models allow far easier modeling and
faster simulations compared to usual full-FEM approaches
without any loss of accuracy.
Abstract: Bio-composites derived from plant fiber and/or bioderived
polymer, are likely more ecofriendly and demonstrate
competitive performance with petroleum based composites. In this
research, the bio phenol-formaldehyde (bio-PF) was used as a matrix
and oil palm empty fruit bunch fiber (EFB) as reinforcement. The
matrix was synthesized via liquefaction and condensation to enhance
the combination of phenol and formaldehyde, during the process.
Then, the bio-PF was mixed with different percentage of EFB (5%,
10%, 15% and 20%) and molded at 180oC. The samples that viewed
under scanning electron microscopy (SEM) showed an excellent
wettability and interaction between EFB and matrix. Samples of 10%
EFB gave the optimum properties of impact and hardness meanwhile
sample 15% of EFB gave the highest reading of flexural modulus
(MOE) and flexural strength (MOR). For thermal stability analysis, it
was found that the weight loss and the activation energy (Ea) of the
bio-composites samples were decreased as the filler content
increased.
Abstract: Iris codes contain bits with different entropy. This
work investigates different strategies to reduce the size of iris
code templates with the aim of reducing storage requirements and
computational demand in the matching process. Besides simple subsampling
schemes, also a binary multi-resolution representation as
used in the JBIG hierarchical coding mode is assessed. We find that
iris code template size can be reduced significantly while maintaining
recognition accuracy. Besides, we propose a two-stage identification
approach, using small-sized iris code templates in a pre-selection
stage, and full resolution templates for final identification, which
shows promising recognition behaviour.
Abstract: Digital image correlation (DIC) is a contactless fullfield
displacement and strain reconstruction technique commonly
used in the field of experimental mechanics. Comparing with
physical measuring devices, such as strain gauges, which only
provide very restricted coverage and are expensive to deploy widely,
the DIC technique provides the result with full-field coverage and
relative high accuracy using an inexpensive and simple experimental
setup. It is very important to study the natural patterns effect on the
DIC technique because the preparation of the artificial patterns is
time consuming and hectic process. The objective of this research is
to study the effect of using images having natural pattern on the
performance of DIC. A systematical simulation method is used to
build simulated deformed images used in DIC. A parameter (subset
size) used in DIC can have an effect on the processing and accuracy
of DIC and even cause DIC to failure. Regarding to the picture
parameters (correlation coefficient), the higher similarity of two
subset can lead the DIC process to fail and make the result more
inaccurate. The pictures with good and bad quality for DIC methods
have been presented and more importantly, it is a systematic way to
evaluate the quality of the picture with natural patterns before they
install the measurement devices.
Abstract: Fructo-oligosaccharides (FOS) are produced from
sucrose by Aureobasidium pullulans in yields between 40-60%
(w/w). To increase the amount of FOS it is necessary to remove the
small, non-prebiotic sugars, present. Two methods for producing
high-purity FOS have been developed: the use of microorganisms
able to consume small saccharides; and the use of continuous
chromatography to separate sugars: simulated moving bed (SMB). It
is herein proposed the combination of both methods. The aim of this
study is to optimize the composition of the fermentative broth (in
terms of salts and sugars) that will be further purified by SMB. A
yield of 0.63 gFOS.gSucrose^-1 was obtained with A. pullulans using low
amounts of salts in the initial fermentative broth. By removing the
small sugars, Saccharomyces cerevisiae and Zymomonas mobilis
increased the percentage of FOS from around 56.0% to 83% (w/w) in
average, losing only 10% (w/w) of FOS during the recovery process.
Abstract: The aim of this study was to design and simulate a
particular type of Asynchronous State Machine (ASM), namely a
‘traffic light controller’ (TLC), operated at a frequency of 0.5 Hz.
The design task involved two main stages: firstly, designing a 4-bit
binary counter using J-K flip flops as the timing signal and,
subsequently, attaining the digital logic by deploying ASM design
process. The TLC was designed such that it showed a sequence of
three different colours, i.e. red, yellow and green, corresponding to
set thresholds by deploying the least number of AND, OR and NOT
gates possible. The software Multisim was deployed to design such
circuit and simulate it for circuit troubleshooting in order for it to
display the output sequence of the three different colours on the
traffic light in the correct order. A clock signal, an asynchronous 4-
bit binary counter that was designed through the use of J-K flip flops
along with an ASM were used to complete this sequence, which was
programmed to be repeated indefinitely. Eventually, the circuit was
debugged and optimized, thus displaying the correct waveforms of
the three outputs through the logic analyser. However, hazards
occurred when the frequency was increased to 10 MHz. This was
attributed to delays in the feedback being too high.
Abstract: It is widely believed that mobile device is a promising technology for lending the opportunity for the third wave of electronic commerce. Mobile devices have changed the way companies do business. Many applications are under development or being incorporated into business processes. In this day, mobile applications are a vital component of any industry strategy.One of the greatest benefits of selling merchandise and providing services on a mobile application is that it widens a company’s customer base significantly.Mobile applications are accessible to interested customers across regional and international borders in different electronic business (e-business) area. But there is a dark side to this success story. The security risks associated with mobile devices and applications are very significant. This paper introduces a broad risk analysis for the various threats, vulnerabilities, and risks in mobile e-business applications and presents some important risk mitigation approaches. It reviews and compares two different frameworks for security assurance in mobile e-business applications. Based on the comparison, the paper suggests some recommendations for applications developers and business owners in mobile e-business application development process.
Abstract: A Silver (Ag) thin film is introduced as a template and
doping source for vertically aligned p–type ZnO nanorods. ZnO
nanorods were grown using an ammonium hydroxide based
hydrothermal process. During the hydrothermal process, the Ag thin
film was dissolved to generate Ag ions in the solution. The Ag ions can
contribute to doping in the wurzite structure of ZnO and the (111)
grain of Ag thin film can be the epitaxial temporal template for the
(0001) plane of ZnO. Hence, Ag–doped p–type ZnO nanorods were
successfully grown on the substrate, which can be an electrode or
semiconductor for the device application. To demonstrate the
potentials of this idea, p–n diode was fabricated and its electrical
characteristics were demonstrated.