Abstract: The use of titanium fluoride and iron fluoride
(TiF3/FeF3) catalysts in combination with polutetrafluoroethylene
(PTFE) in plain zinc- dialkyldithiophosphate (ZDDP) oil is important
for the study of engine tribocomponents and is increasingly a strategy
to improve the formation of tribofilm and provide low friction and
excellent wear protection in reduced phosphorus plain ZDDP oil. The
influence of surface roughness and the concentration of
TiF3/FeF3/PTFE were investigated using bearing steel samples
dipped in lubricant solution at 100°C for two different heating time
durations. This paper addresses the effects of water drop contact
angle using different surface; finishes after treating them with
different lubricant combination. The calculated water drop contact
angles were analyzed using Design of Experiment software (DOE)
and it was determined that a 0.05 μm Ra surface roughness would
provide an excellent TiF3/FeF3/PTFE coating for antiwear resistance
as reflected in the Scanning electron microscopy (SEM) images and
the tribological testing under extreme pressure conditions. Both
friction and wear performance depend greatly on the PTFE/and
catalysts in plain ZDDP oil with 0.05 % phosphorous and on the
surface finish of bearing steel. The friction and wear reducing effects,
which was observed in the tribological tests, indicated a better micro
lubrication effect of the 0.05 μm Ra surface roughness treated at
100°C for 24 hours when compared to the 0.1 μm Ra surface
roughness with the same treatment.
Abstract: Background: Muscle Energy Techniques (MET) have
been widely used by manual therapists over the past years, but still
limited research validated its use and there was limited evidence to
substantiate the theories used to explain its effects. Objective: To
investigate the effect of Muscle Energy Technique (MET) on anterior
pelvic tilt in patients with lumbar spondylosis. Design: Randomized
controlled trial. Subjects: Thirty patients with anterior pelvic tilt from
both sexes were involved, aged between 35 to 50 years old and they
were divided into MET and control groups with 15 patients in each.
Methods: All patients received 3sessions/week for 4 weeks where the
study group received MET, Ultrasound and Infrared, and the control
group received U.S and I.R only. Pelvic angle was measured by
palpation meter, pain severity by the visual analogue scale and
functional disabilities by the Oswestry disability index. Results: Both
groups showed significant improvement in all measured variables.
The MET group was significantly better than the control group in
pelvic angle, pain severity, and functional disability as p-value were
(0.001, 0.0001, 0.0001) respectively. Conclusion and implication: the
study group fulfilled greater improvement in all measured variables
than the control group which implies that application of MET in
combination with U.S and I.R were more effective in improving
pelvic tilting angle, pain severity and functional disabilities than
using electrotherapy only.
Abstract: To evaluate the vigor of wheat seeds and stress of
premature aging effects on germination percentage, root length and
shoot length of five wheat cultivars that include Vynak, Karkheh,
Chamran, Star and Kavir which underwent a period of zero, two,
three, four days in terms of premature aging with 41°C temperature
and 100% relative humidity. Seed germination percentage, root
length and shoot length in these conditions were measured. This
experiment was conducted as a factorial completely randomized
design with four replications in laboratory conditions. The results
showed that each of aging treatments used in this experiment can be
used to detect differences in vigor of wheat varieties. Wheat cultivars
illustrated significant differences in germination percentage, root
length and shoot length in terms of premature aging. The wheat
cultivars; Astar and Vynak had maximum germination percentage
and Karkheh, respectively Kavir and Chamran had lowest percentage
of seed germination. Reactions of root and shoot length of wheat
cultivars was also different. The results showed that the seeds with a
stronger vigor affected less in premature aging condition and the
difference between the percentage of seed germination under normal
conditions and stress was significant and the seeds with the weaker
vigor were more sensitive to the premature aging stress and the
premature aging had more severe negative impact on seed vigor.
Abstract: This paper presents results of the survey regarding the
awareness about HIV/AIDS among HIV-infected individuals. A
questionnaire covering various aspects of HIV-infection was
conducted among 110 HIV-infected individuals who attended the
G.A. Zaharyan Moscow Tuberculosis Clinic, Department for
treatment of TB patients with HIV. The questionnaire included
questions about modes of HIV transmission and preventive measures
against HIV/AIDS, as well as questions about age, gender, education
and employment status. The survey revealed that the respondents in
the whole had a good knowledge regarding modes of HIV
transmission and preventive measures against HIV/AIDS: about
83,6% male respondents and 85,7% female respondents gave an
accurate answers regarding the HIV-infection. However, the
overwhelming majority of the study participants, that is, 88,5% men
and 98% women, was quite ignorant about the risk of acquiring HIV
through saliva and toothbrush of HIV-infected individual. Though
that risk is rather insignificant, it is still biologically possible. And
this gap in knowledge needs to be filled. As the study showed another
point of concern was the fact, that despite the knowledge of HIV
transmission risk through unprotected sex about 40% percent of HIVpositive
men and 25% of HIV-positive women did not insist on using
condoms with their sexual partners. These findings indicate that there
are still some aspects about HIV-infection which needed to be
clarified and explained through more detailed and specific
educational programs.
Abstract: A lower consumption of thermal energy will
contribute not only to a reduction in the running costs, but also in the
reduction of pollutant emissions that contribute to the greenhouse
effect. Cogeneration or CHP (Combined Heat and Power) is the
system that produces power and usable heat simultaneously by
decreasing the pollutant emissions and increasing the efficiency.
Combined production of mechanical or electrical and thermal energy
using a simple energy source, such as oil, coal, natural or liquefied
gas, biomass or the sun; affords remarkable energy savings and
frequently makes it possible to operate with greater efficiency when
compared to a system producing heat and power separately. This
study aims to bring out the contributions of cogeneration systems to
the environment and sustainability by saving the energy and reducing
the emissions. In this way we made a comprehensive investigation in
the literature by focusing on the environmental aspects of the
cogeneration systems. In the light of these studies we reached that,
cogeneration systems must be consider in sustainability and their
benefits on protecting the ecology must be investigated.
Abstract: Particle size distribution, the most important
characteristics of aerosols, is obtained through electrical
characterization techniques. The dynamics of charged nanoparticles
under the influence of electric field in Electrical Mobility
Spectrometer (EMS) reveals the size distribution of these particles.
The accuracy of this measurement is influenced by flow conditions,
geometry, electric field and particle charging process, therefore by
the transfer function (transfer matrix) of the instrument. In this work,
a wire-cylinder corona charger was designed and the combined fielddiffusion
charging process of injected poly-disperse aerosol particles
was numerically simulated as a prerequisite for the study of a
multichannel EMS. The result, a cloud of particles with no uniform
charge distribution, was introduced to the EMS. The flow pattern and
electric field in the EMS were simulated using Computational Fluid
Dynamics (CFD) to obtain particle trajectories in the device and
therefore to calculate the reported signal by each electrometer.
According to the output signals (resulted from bombardment of
particles and transferring their charges as currents), we proposed a
modification to the size of detecting rings (which are connected to
electrometers) in order to evaluate particle size distributions more
accurately. Based on the capability of the system to transfer
information contents about size distribution of the injected particles,
we proposed a benchmark for the assessment of optimality of the
design. This method applies the concept of Von Neumann entropy
and borrows the definition of entropy from information theory
(Shannon entropy) to measure optimality. Entropy, according to the
Shannon entropy, is the ''average amount of information contained in
an event, sample or character extracted from a data stream''.
Evaluating the responses (signals) which were obtained via various
configurations of detecting rings, the best configuration which gave
the best predictions about the size distributions of injected particles,
was the modified configuration. It was also the one that had the
maximum amount of entropy. A reasonable consistency was also
observed between the accuracy of the predictions and the entropy
content of each configuration. In this method, entropy is extracted
from the transfer matrix of the instrument for each configuration.
Ultimately, various clouds of particles were introduced to the
simulations and predicted size distributions were compared to the
exact size distributions.
Abstract: Grains, including oats (Avena sativa L.), have been
recognized functional foods, because provide beneficial effect on the
health of the consumer and decrease the risk of various diseases. Oats
are good source of soluble fibre, essential amino acids, unsaturated
fatty acids, vitamins and minerals. Oat breeders have developed oat
varieties and improved yielding ability potential of oat varieties.
Therefore, the aim of investigation was to analyze the composition of
perspective oat varieties and breeding lines grains grown in different
conditions and evaluate functional properties. In the studied samples
content of protein, starch, β-glucans, total dietetic fibre, composition
of amino acids and vitamin E were determined. The results of
analysis showed that protein content depending of varieties ranged
9.70% to 17.30% total dietary fibre 13.66 g100g-1 to 30.17 g100g-1,
content of β-glucans 2.7 g100g-1 to 3.5 g100g-1, amount of
vitamin E (α-tocopherol) determined from 4 mgkg-1 to 9.9 mgkg-1.
The sums of essential amino acids in oat grain samples were
determined from 31.63 gkg-1 to 54.90 gkg-1. It is concluded that
amino acids composition of husked and naked oats grown in organic
or conventional conditions is close to optimal for human health.
Abstract: The objective of the study is to assess the
implementation of LED lighting into forest machine work in the dark.
In addition, the paper includes a wide variety of important and
relevant safety and health parameters. In modern, computerized work
in the cab of forest machines, artificial illumination is a demanding
task when performing duties, such as the visual inspections of wood
and computer calculations. We interviewed entrepreneurs and
gathered the following as the most pertinent themes: (1) safety, (2)
practical problems, and (3) work with LED lighting. The most
important comments were in regards to the practical problems of
LED lighting. We found indications of technical problems in
implementing LED lighting, like snow and dirt on the surfaces of
lamps that dim the emission of light. Moreover, service work in the
dark forest is dangerous and increases the risks of on-site accidents.
We also concluded that the amount of blue light to the eyes should be
assessed, especially, when the drivers are working in a semi-dark cab.
Abstract: Nine Degrees of Freedom (9 DOF) systems are
already in development in many areas. In this paper, an integrated
pressure sensor is proposed that will make use of an already existing
monolithic 9 DOF inertial MEMS platform. Capacitive pressure
sensors can suffer from limited sensitivity for a given size of
membrane. This novel pressure sensor design increases the sensitivity
by over 5 times compared to a traditional array of square diaphragms
while still fitting within a 2 mm x 2 mm chip and maintaining a fixed
static capacitance. The improved design uses one large diaphragm
supported by pillars with fixed electrodes placed above the areas of
maximum deflection. The design optimization increases the
sensitivity from 0.22 fF/kPa to 1.16 fF/kPa. Temperature sensitivity
was also examined through simulation.
Abstract: This paper presents thermal annealing de-wetting
technique for the preparation of porous metal membrane for Thin
Film Encapsulation (TFE) application. Thermal annealing de-wetting
experimental results reveal that pore size formation in porous metal
membrane depend upon i.e. 1. The substrate at which metal is
deposited, 2. Melting point of metal used for porous metal cap layer
membrane formation, 3. Thickness of metal used for cap layer, 4.
Temperature used for formation of porous metal membrane. In order
to demonstrate this technique, Silver (Ag) was used as a metal for
preparation of porous metal membrane on amorphous silicon (a-Si)
and silicon oxide. The annealing of the silver thin film of various
thicknesses was performed at different temperature. Pores in porous
silver film were analyzed using Scanning Electron Microscope
(SEM). In order to check the usefulness of porous metal film for TFE
application, the porous silver film prepared on amorphous silicon (a-
Si) and silicon oxide was released using XeF2 and VHF, respectively.
Finally, guide line and structures are suggested to use this porous
membrane for robust TFE application.
Abstract: The aim of the present study is to investigate
consumers' determinants of intention toward the adoption of Smart
Grid solutions and technologies. Ajzen's Theory of Planned
Behaviour (TPB) model is applied and tested to explain the formation
of such adoption intention. An exogenous variable, taking into
account the resistance to change of individuals, was added to the
basic model. The elicitation study allowed obtaining salient modal
beliefs, which were used, with the support of literature, to design the
questionnaire. After the screening phase, data collected from the
main survey were analysed for evaluating measurement model's
reliability and validity. Consistent with the theory, the results of
structural equation analysis revealed that attitude, subjective norm,
and perceived behavioural control positively, which affected the
adoption intention. Specifically, the variable with the highest estimate
loading factor was found to be the perceived behavioural control,
and, the most important belief related to each construct was
determined (e.g., energy saving was observed to be the most
significant belief linked with attitude). Further investigation indicated
that the added exogenous variable has a negative influence on
intention; this finding confirmed partially the hypothesis, since this
influence was indirect: such relationship was mediated by attitude.
Implications and suggestions for future research are discussed.
Abstract: The purpose of this project is to propose a quick and
environmentally friendly alternative to measure the quality of oils
used in food industry. There is evidence that repeated and
indiscriminate use of oils in food processing cause physicochemical
changes with formation of potentially toxic compounds that can
affect the health of consumers and cause organoleptic changes. In
order to assess the quality of oils, non-destructive optical techniques
such as Interferometry offer a rapid alternative to the use of reagents,
using only the interaction of light on the oil. Through this project, we
used interferograms of samples of oil placed under different heating
conditions to establish the changes in their quality. These
interferograms were obtained by means of a Mach-Zehnder
Interferometer using a beam of light from a HeNe laser of 10mW at
632.8nm. Each interferogram was captured, analyzed and measured
full width at half-maximum (FWHM) using the software from
Amcap and ImageJ. The total of FWHMs was organized in three
groups. It was observed that the average obtained from each of the
FWHMs of group A shows a behavior that is almost linear, therefore
it is probable that the exposure time is not relevant when the oil is
kept under constant temperature. Group B exhibits a slight
exponential model when temperature raises between 373 K and 393
K. Results of the t-Student show a probability of 95% (0.05) of the
existence of variation in the molecular composition of both samples.
Furthermore, we found a correlation between the Iodine Indexes
(Physicochemical Analysis) and the Interferograms (Optical
Analysis) of group C. Based on these results, this project highlights
the importance of the quality of the oils used in food industry and
shows how Interferometry can be a useful tool for this purpose.
Abstract: Biodiesel is one of the alternative fuels that promising
for substituting petro diesel as energy source which is advantage on
sustainability and ecofriendly. Due to the raw material that tend to
decompose during storage, biodiesel also have the same characteristic
that tend to decompose and formed higher acid value which is the
result of oxidation to double bond on a chain of ester. Decomposition of biodiesel due to oxidation reaction could
prevent by introduce a small amount of antioxidant. The origin of raw
materials and the process for producing biodiesel will determine the
effectiveness of antioxidant. The quality degradation on biodiesel
could evaluate by measuring iodine value and acid number of
biodiesel. Biodiesel made from high fatty acid Jatropha curcas oil by using
esterification and transesterification process will stand on the quality
by introduce 90 ppm pyrogallol powder on the biodiesel, which could
increase Induction period time from 2 hours to more than 6 hours in
rancimat test evaluation.
Abstract: Currently, green rating systems are mainly utilized for
correctly sizing mechanical and electrical systems, which have short
lifetime expectancies. In these systems, passive solar and bio-climatic
architecture, which have long lifetime expectancies, are neglected.
Urban rating systems consider buildings and services in addition to
neighborhoods and public transportation as integral parts of the built
environment. The main goal of this study was to develop a more
consistent point allocation system for urban building standards by
using six different lifetime shearing layers: Site, Structure, Skin,
Services, Space, and Stuff, each reflecting distinct environmental
damages. This shearing-layer concept was applied to internationally
well-known rating systems: Leadership in Energy and Environmental
Design (LEED) for Neighborhood Development, BRE
Environmental Assessment Method (BREEAM) for Communities
and Comprehensive Assessment System for Building Environmental
Efficiency (CASBEE) for Urban Development. The results showed
that LEED for Neighborhood Development and BREEAM for
Communities focused on long-lifetime-expectancy building designs,
whereas CASBEE for Urban Development gave equal importance to
the Building and Service Layers. Moreover, although this rating
system was applied using a building-scale assessment, “Urban Area +
Buildings” focuses on a short-lifetime-expectancy system design,
neglecting to improve the architectural design by considering bioclimatic
and passive solar aspects.
Abstract: Currently there are many use of threaded reinforcing
bars in construction fields because those do not need additional screw
processing when connecting reinforcing bar by threaded coupler. In
this study, reinforced concrete bridge piers using threaded rebar
coupler system at the plastic hinge area were tested to evaluate seismic
performance. The test results showed that threads of the threaded rebar
coupler system could be loosened while under tension-compression
cyclic loading because tolerance and rib face angle of a threaded rebar
coupler system are greater than that of a conventional ribbed rebar
coupler system. As a result, cracks were concentrated just outside of
the mechanical coupler and stiffness of reinforced concrete bridge pier
decreased. Therefore, it is recommended that connection ratio of
mechanical couplers in one section shall be below 50% in order that
cracks are not concentrated just outside of the mechanical coupler.
Also, reduced stiffness of the specimen should be considered when
using the threaded rebar coupler system.
Abstract: Mobile Adhoc Networks (MANETs) are
infrastructure-less, dynamic network of collections of wireless mobile
nodes communicating with each other without any centralized
authority. A MANET is a mobile device of interconnections through
wireless links, forming a dynamic topology. Routing protocols have a
big role in data transmission across a network. Routing protocols,
two major classifications are unipath and multipath. This study
evaluates performance of an on-demand multipath routing protocol
named Adhoc On-demand Multipath Distance Vector routing
(AOMDV). This study proposes Energy Aware AOMDV (EAAOMDV)
an extension of AOMDV which decreases energy
consumed on a route.
Abstract: Phonocardiography is important in appraisal of
congenital heart disease and pulmonary hypertension as it reflects the
duration of right ventricular systoles. The systolic murmur in patients
with intra-cardiac shunt decreases as pulmonary hypertension
develops and may eventually disappear completely as the pulmonary
pressure reaches systemic level. Phonocardiography and auscultation
are non-invasive, low-cost, and accurate methods to assess heart
disease. In this work an objective signal processing tool to extract
information from phonocardiography signal using Wavelet is
proposed to classify the murmur as normal or abnormal. Since the
feature vector is large, a Binary Particle Swarm Optimization (PSO)
with mutation for feature selection is proposed. The extracted
features improve the classification accuracy and were tested across
various classifiers including Naïve Bayes, kNN, C4.5, and SVM.
Abstract: In order to study the effect of different levels of triple
super phosphate chemical fertilizer and biological phosphate fertilizer
(fertile 2) on some morphological traits of corn this research was
carried out in Ahvaz in 2002 as a factorial experiment in randomized
complete block design with 4 replications). The experiment included
two factors: first, biological phosphate fertilizer (fertile 2) at three
levels of 0, 100, 200 g/ha; second, triple super phosphate chemical
fertilizer at three levels of 0, 60, 90 kg/ha of pure phosphorus (P2O5).
The obtained results indicated that fertilizer treatments had a
significant effect on some morphological traits at 1% probability
level. In this regard, P2B2 treatment (100 g/ha biological phosphate
fertilizer (fertile 2) and 60 kg/ha triple super phosphate fertilizer) had
the greatest plant height, stem diameter, number of leaves and ear
length. It seems that in Ahvaz weather conditions, decrease of
consumption of triple superphosphate chemical fertilizer to less than
a half along with the consumption of biological phosphate fertilizer
(fertile 2) is highly important in order to achieve optimal results.
Therefore, it can be concluded that biological fertilizers can be used
as a suitable substitute for some of the chemical fertilizers in
sustainable agricultural systems.
Abstract: This paper represents an experimental study of LPG
diffusion flame at elevated preheated air temperatures. The flame is
stabilized in a vertical water-cooled combustor by using air swirler. An
experimental test rig was designed to investigate the different
operating conditions. The burner head is designed so that the LPG fuel
issued centrally and surrounded by the swirling air issues from an air
swirler. There are three air swirlers having the same dimensions but
having different blade angles to give different swirl numbers of 0.5,
0.87 and 1.5. The combustion air was heated electrically before
entering the combustor up to a temperature about 500 K. Five air to
fuel mass ratios of 15, 20, 30, 40 and 50 were also studied. The effect
of preheated air temperature, swirl number and air to fuel mass ratios
on the temperature maps, visible flame length, high temperature region
(size) and exhaust species concentrations are studied. Some results
show that as the preheated air temperature increases, the volume of
high temperature region also increased but the flame length decreased.
Increasing the preheated air temperature, EINOx, EICO2 and EIO2
increased, while EICO decreased. Increasing the preheated air
temperature from 300 to 500 K, for all air swirl numbers used, the
highest increase in EINOx, EICO2 and EIO2 are 141, 4 and 65%,
respectively.
Abstract: Experiential marketing is one of the marketing
approaches that offer an exceptional framework to integrate elements
of experience and entertainment in a product or service. Experiential
marketing is defined as a memorable experience that goes deeply into
the customer’s mind. Besides that, customer satisfaction is defined as
an emotional response to the experiences provided by and associated
with particular products or services purchased. Thus, experiential
marketing activities can affect the level of customer satisfaction and
loyalty. In this context, the research aims to explore the relationship
among experiential marketing, customer satisfaction and customer
loyalty among the cosmetic products customers in Konya. The partial
least squares (PLS) method is used to analyze the survey data.
Findings of the present study revealed that experiential marketing has
been a significant predictor of customer satisfaction and customer
loyalty, and also experiential marketing has a significantly positive
effect on customer satisfaction and customer loyalty.