Abstract: This paper has introduced a slope photogrammetric mapping using unmanned aerial vehicle. There are two units of UAV has been used in this study; namely; fixed wing and multi-rotor. Both UAVs were used to capture images at the study area. A consumer digital camera was mounted vertically at the bottom of UAV and captured the images at an altitude. The objectives of this study are to obtain three dimensional coordinates of slope area and to determine the accuracy of photogrammetric product produced from both UAVs. Several control points and checkpoints were established Real Time Kinematic Global Positioning System (RTK-GPS) in the study area. All acquired images from both UAVs went through all photogrammetric processes such as interior orientation, exterior orientation, aerial triangulation and bundle adjustment using photogrammetric software. Two primary results were produced in this study; namely; digital elevation model and digital orthophoto. Based on results, UAV system can be used to mapping slope area especially for limited budget and time constraints project.
Abstract: The comparisons of two typical fluidic thrust vectoring exhaust nozzles including two-dimensional(2-D) nozzle and axisymmetric nozzle on aerodynamic characteristics was presented by numerical simulation. The results show: the thrust vector angles increased with the increasing secondary flow but decreased with the nozzle pressure ratio (NPR) increasing. With the same secondary flow and NPR, the thrust vector angles of 2-D nozzle were higher than the axisymmetric nozzle-s. So with the lower NPR and more secondary weight flow, the much higher thrust vector angle was caused by 2-D fluidic nozzle. And with the higher NPR and less secondary weight flow, there was not much difference in angular dimension between two nozzles.
Abstract: Periphyton development and composition were
studied in three different treatments: (i) two fishpond units of
wetland-type wastewater treatment pond systems, (ii) two fishponds
in combined intensive-extensive fish farming systems and (iii) three
traditional polyculture fishponds. Results showed that amounts of
periphyton developed in traditional polyculture fishponds (iii) were
different compared to the other treatments (i and ii), where the main
function of ponds was stated wastewater treatment. Negative
correlation was also observable between water quality parameters
and periphyton production. The lower trophity, halobity and
saprobity level of ponds indicated higher amount of periphyton. The
dry matter content of periphyton was significantly higher in the
samples, which were developed in traditional polyculture fishponds
(2.84±3.02 g m-2 day-1, whereby the ash content in dry matter 74%),
than samples taken from (i) (1.60±2.32 g m-2 day-1, 61%) and (ii)
fishponds (0.65±0.45 g m-2 day-1, 81%).
Abstract: Scaffolds play a key role in tissue engineering and can be produced in many different ways depending on the applications and the materials used. Most researchers used an experimental trialand- error approach into new biomaterials but computer simulation applied to tissue engineering can offer a more exhaustive approach to test and screen out biomaterials. This paper develops the model of scaffolds and Computational Fluid Dynamics that show the value of computer simulations in determining the influence of the geometrical scaffold parameter porosity, pore size and shape on the permeability of scaffolds, magnitude of velocity, drop pressure, shear stress distribution and level and the proper design of the geometry of the scaffold. This creates a need for more advanced studies that include aspects of dynamic conditions of a micro fluid passing through the scaffold were characterized for tissue engineering applications and differentiation of tissues within scaffolds.
Abstract: Dietary macro and micro nutrients in their respective proportion and fractions present a practical potential tool to fabricate milk constituents since cells of lactating mammary glands obtain about 80 % of milk synthesis nutrients from blood, reflecting the existence of an isotonic equilibrium between blood and milk. Diverting milk biosynthetic activities through manipulation of nutrients towards producing milk not only keeping in view its significance as natural food but also as food item which prevents or dilutes the adverse effects of some diseases (like cardiovascular problem by saturated milk fat intake) has been area of interest in the last decade. Nutritional modification / supplementation has been reported to enhance conjugated linoleic acid, fatty acid type and concentration, essential fatty acid concentration, vitamin B12& C, Se, Cu, I and Fe which are involved to counter the health threats to human well being. Synchronizing dietary nutrients aimed to modify rumen dynamics towards synthesis of nutrients or their precursors to make their drive towards formulated milk constituents presents a practical option. Formulating dietary constituents to design milk constituents will let the farmers, consumers and investors know about the real potential and profit margins associated with this enterprise. This article briefly recapitulates the ways and means to modify milk constituents keeping an eye on human health and well being issues, which allows milk to serve more than a food item.
Abstract: Vinegar is a precious food additive and complement as well as effective preservative against food spoilage. Recently traditional vinegar production has been improved using various natural substrates and fruits such as grape, palm, cherry, coconut, date, sugarcane, rice and balsam. These neoclassical fermentations resulted in several vinegar types with different tastes, fragrances and nutritional values because of applying various acetic acid bacteria as starters. Acetic acid bacteria include genera Acetobacter, Gluconacetobacter and Gluconobacter according to latest edition of Bergy-s Manual of Systematic Bacteriology that classifies genera on the basis of their 16s RNA differences. Acetobacter spp as the main vinegar starters belong to family Acetobacteraceae that are gram negative obligate aerobes, chemoorganotrophic bacilli that are oxidase negative and oxidize ethanol to acetic acid. In this research we isolated and identified a native Acetobacter strain with high acetic acid productivity and tolerance against high ethanol concentrations from Iranian peach as a summer delicious fruit that is very susceptible to food spoilage and decay. We used selective and specific laboratorial culture media such as Standard GYC, Frateur and Carr medium. Also we used a new industrial culture medium and a miniature fermentor with a new aeration system innovated by Pars Yeema Biotechnologists Co., Isfahan Science and Technology Town (ISTT), Isfahan, Iran. The isolated strain was successfully cultivated in modified Carr media with 2.5% and 5% ethanol simultaneously in high temperatures, 34 - 40º C after 96 hours of incubation period. We showed that the increase of ethanol concentration resulted in rising of strain sensitivity to high temperature. In conclusion we isolated and characterized a new Acetobacter strain from Iranian peach that could be considered as a potential strain for production of a new vinegar type, peach vinegar, with a delicious taste and advantageous nutritional value in food biotechnology and industrial microbiology.
Abstract: Image clustering is a process of grouping images
based on their similarity. The image clustering usually uses the color
component, texture, edge, shape, or mixture of two components, etc.
This research aims to explore image clustering using color
composition. In order to complete this image clustering, three main
components should be considered, which are color space, image
representation (feature extraction), and clustering method itself. We
aim to explore which composition of these factors will produce the
best clustering results by combining various techniques from the
three components. The color spaces use RGB, HSV, and L*a*b*
method. The image representations use Histogram and Gaussian
Mixture Model (GMM), whereas the clustering methods use KMeans
and Agglomerative Hierarchical Clustering algorithm. The
results of the experiment show that GMM representation is better
combined with RGB and L*a*b* color space, whereas Histogram is
better combined with HSV. The experiments also show that K-Means
is better than Agglomerative Hierarchical for images clustering.
Abstract: A new numerical method for simultaneously updating mass and stiffness matrices based on incomplete modal measured data is presented. By using the Kronecker product, all the variables that are to be modified can be found out and then can be updated directly. The optimal approximation mass matrix and stiffness matrix which satisfy the required eigenvalue equation and orthogonality condition are found under the Frobenius norm sense. The physical configuration of the analytical model is preserved and the updated model will exactly reproduce the modal measured data. The numerical example seems to indicate that the method is quite accurate and efficient.
Abstract: Factor analysis was applied to two stages biogas
production from banana stem waste allowing a screening of the
experimental variables second stage temperature (T), organic loading
rates (OLR) and hydraulic retention times (HRT). Biogas production
was found to be strongly influenced by all the above experimental
variables. Results from factorial analysis have shown that all
variables which were HRT, OLR and T have significant effect to
biogas production. Increased in HRT and OLR could increased the
biogas yield. The performance was tested under the conditions of
various T (35oC-60oC), OLR (0.3 g TS/l.d–1.9 gTS/l.d), and HRT (3
d–15 d). Conditions for temperature, OLR and HRT in this study
were based on the best range obtained from literature review.
Abstract: Selecting the routes and the assignment of link flow in a computer communication networks are extremely complex combinatorial optimization problems. Metaheuristics, such as genetic or simulated annealing algorithms, are widely applicable heuristic optimization strategies that have shown encouraging results for a large number of difficult combinatorial optimization problems. This paper considers the route selection and hence the flow assignment problem. A genetic algorithm and simulated annealing algorithm are used to solve this problem. A new hybrid algorithm combining the genetic with the simulated annealing algorithm is introduced. A modification of the genetic algorithm is also introduced. Computational experiments with sample networks are reported. The results show that the proposed modified genetic algorithm is efficient in finding good solutions of the flow assignment problem compared with other techniques.
Abstract: Gliding during night without electric power is an efficient method to enhance endurance performance of solar aircrafts. The properties of maximum gliding endurance path are studied in this paper. The problem is formulated as an optimization problem about maximum endurance can be sustained by certain potential energy storage with dynamic equations and aerodynamic parameter constrains. The optimal gliding path is generated based on gauss pseudo-spectral method. In order to analyse relationship between altitude, velocity of solar UAVs and its endurance performance, the lift coefficient in interval of [0.4, 1.2] and flight envelopes between 0~30km are investigated. Results show that broad range of lift coefficient can improve solar aircrafts- long endurance performance, and it is possible for a solar aircraft to achieve the aim of long endurance during whole night just by potential energy storage.
Abstract: The purpose of this research was to study five vital
factors related to employees’ job performance. A total of 250
respondents were sampled from employees who worked at a public
warehouse organization, Bangkok, Thailand. Samples were divided
into two groups according to their work experience. The average
working experience was about 9 years for group one and 28 years for
group two. A questionnaire was utilized as a tool to collect data.
Statistics utilized in this research included frequency, percentage,
mean, standard deviation, t-test analysis, one way ANOVA, and
Pearson Product-moment correlation coefficient. Data were analyzed
by using Statistical Package for the Social Sciences. The findings
disclosed that the majority of respondents were female between 23-
31 years old, single, and hold an undergraduate degree. The average
income of respondents was less than 30,900 baht. The findings also
revealed that the factors of organization chart awareness, job process
and technology, internal environment, employee loyalty, and policy
and management were ranked as medium level. The hypotheses
testing revealed that difference in gender, age, and position had
differences in terms of the awareness of organization chart, job
process and technology, internal environment, employee loyalty, and
policy and management in the same direction with low level.
Abstract: This study was carried out to develop a flotation
procedure for an oxide copper ore from a Region in Central Africa
for producing an 18% copper concentrate for downstream processing
at maximum recovery from a 4% copper feed grade. The copper
recoveries achieved from the test work were less than 50% despite
changes in reagent conditions (multistage sulphidisation, use of RCA
emulsion and mixture, use of AM 2, etc). The poor recoveries were
attributed to the mineralogy of the ore from which copper silicates
accounted for approximately 70% (mass) of the copper minerals in
the ore. These can be complex and difficult to float using
conventional flotation methods. Best results were obtained using
basic sulphidisation procedures, a high flotation temperature and
extended flotation residence time.
Abstract: Aspheric optical components are an alternative to the use of conventional lenses in the implementation of imaging systems for the visible range. Spherical lenses are capable of producing aberrations. Therefore, they are not able to focus all the light into a single point. Instead, aspherical lenses correct aberrations and provide better resolution even with compact lenses incorporating a small number of lenses.
Metrology of these components is very difficult especially when the resolution requirements increase and insufficient or complexity of conventional tools requires the development of specific approaches to characterization.
This work is part of the problem existed because the objectives are the study and comparison of different methods used to measure surface rays hybrid aspherical lenses.
Abstract: Pyrolysis of waste tire is one of alternative technique
to produce petrochemicals, such as light olefins, mixed C4, and monoaromatics.
Noble metals supported on acid zeolite catalysts were
reported as potential catalysts to produce the high valuable products
from waste tire pyrolysis. Especially, Pd supported on HBeta gave a
high yield of olefins, mixed C4, and mono-aromatics. Due to the high
prices of noble metals, the objective of this work was to investigate
whether or not a non-noble Ni metal can be used as a substitute of a
noble metal, Pd, supported on HBeta as a catalyst for waste tire pyrolysis.
Ni metal was selected in this work because Ni has high activity
in cracking, isomerization, hydrogenation and the ring opening of
hydrocarbons Moreover, Ni is an element in the same group as Pd
noble metal, which is VIIIB group, aiming to produce high valuable
products similarly obtained from Pd. The amount of Ni was varied as
5, 10, and 20% by weight, for comparison with a fixed 1 wt% Pd,
using incipient wetness impregnation. The results showed that as a
petrochemical-producing catalyst, 10%Ni/HBeta performed better
than 1%Pd/HBeta because it did not only produce the highest yield of
olefins and cooking gases, but the yields were also higher than
1%Pd/HBeta. 5%Ni/HBeta can be used as a substitute of
1%Pd/HBeta for similar crude production because its crude contains
the similar amounts of naphtha and saturated HCs, although it gave
no concentration of light mono-aromatics (C6-C11) in the oil. Additionally,
10%Ni/HBeta that gave high olefins and cooking gases was
found to give a fairly high concentration of the light mono-aromatics
in the oil.
Abstract: The demand of hydrocarbons has increased the
construction of pipelines and the protection of the physical and
mechanical integrity of the already existing infrastructure. Corrosion
is the main reason of failures in the pipeline and it is mostly produced
by acid (HCOOCH3). In this basis, a CFD code was used, in order to
study the corrosion of internal wall of hydrocarbons pipeline. In this
situation, the corrosion phenomenon shows a growing deposit, which
causes defect damages (welding or fabrication) at diverse positions
along the pipeline. The solution of the pipeline corrosion is based on
the diminution of the Naphthenic acid.
Abstract: Solar energy is not only sustainable but also a clean
alternative to be used as source of high temperature heat for many
processes and power generation. However, the major drawback of
solar energy is its transient nature. Especially in solar
thermochemical processing, it is crucial to maintain constant or semiconstant
temperatures inside the solar reactor. In our laboratory, we
have developed a mechanism allowing us to achieve semi-constant
temperature inside the solar reactor. In this paper, we introduce the
concept along with some updated designs and provide the optical
analysis of the concept under various incoming flux.
Abstract: Relevant agricultural information disseminator
(extension agent) ratio of 1:3500 farm families which become a
menace to agricultural production capacity in developing countries
necessitate this study. Out of 4 zones in the state, 24 extension agents
in each zone, 4 extension agents using cell phones and 120 farmers
using cell phone and 120 other farmers not using cell phone were
purposively selected to give 240 farmers that participated in the
research. Data were collected using interview guide and analysized
using frequency, percentage and t-test.. Frequency of contact with
agricultural information centers revealed that cell phone user farmers
had greater means score of X 41.43 contact as against the low mean
X19.32 contact recorded by farmers receiving agricultural
information from extension agents not using cell phone and their
production was statistically significant at P < 0.05. Usage of cell
phone increase extension agent contact and increase farmers-
production capacity.
Abstract: Using quantum hydrodynamical (QHD) model the linear dispersion relation for the electron plasma waves propagating in a cylindrical waveguide filled with a dense plasma containing streaming electron, hole and stationary charged dust particles has been derived. It is shown that the effect of finite boundary and stream velocity of electrons and holes make some of the possible modes of propagation linearly unstable. The growth rate of this instability is shown to depend significantly on different plasma parameters.
Abstract: Today, Hydroforming technology provides an
attractive alternative to conventional matched die forming, especially
for cost-sensitive, lower volume production, and for parts with
irregular contours. In this study the critical fluid pressures which lead
to rupture in the workpiece has been investigated by theoretical and
finite element methods. The axisymmetric analysis was developed to
investigate the tearing phenomenon in cylindrical Hydroforming
Deep Drawing (HDD). By use of obtained equations the effect of
anisotropy, drawing ratio, sheet thickness and strain hardening
exponent on tearing diagram were investigated.