Abstract: Mechanical behavior of 6082T6 aluminum is
investigated at different temperatures. The strain rate sensitivity is
investigated at different temperatures on the grain size variants. The
sensitivity of the measured grain size variants on 3-D grain is
discussed. It is shown that the strain rate sensitivities are negative for
the grain size variants during the deformation of nanostructured
materials. It is also observed that the strain rate sensitivities vary in
different ways with the equivalent radius, semi minor axis radius,
semi major axis radius and major axis radius. From the obtained
results, it is shown that the variation of strain rate sensitivity with
temperature suggests that the strain rate sensitivity at the low and the
high temperature ends of the 6082T6 aluminum range is different.
The obtained results revealed transition at different temperature from
negative strain rate sensitivity as temperature increased on the grain
size variants.
Abstract: Now, the use of renewable energy power generation
has been advanced. In this paper, we compared the usable amount of
resource for photovoltaic power generation which was estimated using
the NEDO formula and the expansion support policy of photovoltaic
power generation which was researched using Internet in the
municipality level in Hokkaido and Aichi Prefecture, Japan. This
paper will contribute to grasp the current situation especially about the
policy. As a result, there were municipalities which seemed to be no
consideration of fitting the amount of resources. We think it would
need to consider the suitability between the resources and policies.
Abstract: Job satisfaction and motivation have been given an
important attention in psychology because they are seen as main
instruments in maintaining organizational growth and development;
they are also used to accomplish organizational aims and objectives.
However, it has been observed that some institutions failed in
motivating and stimulating their workers; in contrast, workers may be
motivated but not satisfied with the job and failed to perform
efficiently and effectively. It is hoped that the study of this nature
would be of significance value to all stakeholders in education
specifically, lecturers in higher institutions in Nigeria. Also, it is
hoped that the findings of this study will enhance lecturers’
effectiveness and performance in discharging their duties. In the light
of the above statements, this study investigated whether job
satisfaction and motivation predict lecturers’ effectiveness in Nigeria
Police Academy, Wudil, Kano State. Correlational research method
was adopted for the study, while purposive sampling technique was
used to choose the institution and the sampled lectures (70). Simple
random sampling technique was used to select one hundred cadets
across the academy. Two instruments were used to elicit information
from both lecturers and cadets. These were job satisfaction and
motivation; and lecturers’ effectiveness Questionnaires. The
instruments were subjected to pilot testing and found to have
reliability coefficient of 0.69 and 0.71 respectively. The results of the
study revealed that there was a significance relationship among job
satisfaction, motivation and lecturers effectiveness in Nigeria Police
Academy. There was a significance relationship between job
satisfaction and lecturers’ effectiveness in Nigeria Police Academy
the cal r is 0.21 while the crt r is 0.19. at p
Abstract: Over the past few decades, manufacturing has evolved
from a more labor-intensive set of mechanical processes to a
sophisticated set of information based technology processes. With the
existence of various advanced manufacturing technologies (AMTs),
more and more functions or jobs are performed by these machines
instead of human labour. This study was undertaken in order to
research the extent of AMTs adoption in manufacturing companies in
Kenya. In order to investigate a survey was conducted via
questionnaires that were sent to 183 selected AMT manufacturing
companies in Kenya. 92 companies responded positively. All the
surveyed companies were found to have a measure of investment in
at least two of the 14 types of AMTs investigated. In general the
company surveyed showed that the level of AMT adoption in Kenya
is very low with investments levels at a mean of 2.057 and
integration levels at a mean of 1.639 in a scale of 1-5.
Abstract: Gladiolus is an important cash crop and is grown
mainly for its elegant spikes. Traditionally the gladiolus corms are
planted manually which is very tedious, time consuming and labor
intensive operation. So far, there is no planter available for planting
of gladiolus corms. With a view to mechanize the planting operation
of this horticultural crop, a prototype of 4-row gladiolus planter was
developed and its performance was evaluated in-situ condition. Cupchain
type metering device was used to place each single gladiolus
corm in furrow at required spacing while planting. Three levels of
corm spacing viz 15, 20 and 25 cm and four levels of forward speed
viz 1.0, 1.5, 2.0 and 2.5 km/h was taken as evaluation parameter for
the planter. The performance indicators namely corm spacing in each
row, coefficient of uniformity, missing index, multiple index, quality
of feed index, number of corms per meter length, mechanical damage
to the corms etc. were determined during the field test. The data was
statistically analyzed using Completely Randomized Design (CRD)
for testing the significance of the parameters. The result indicated
that planter was able to drop the corms at required nominal spacing
with minor variations. The highest deviation from the mean corm
spacing was observed as 3.53 cm with maximum coefficient of
variation as 13.88%. The highest missing and quality of feed indexes
were observed as 6.33% and 97.45% respectively with no multiples.
The performance of the planter was observed better at lower forward
speed and wider corm spacing. The field capacity of the planter was
found as 0.103 ha/h with an observed field efficiency of 76.57%.
Abstract: In this paper, approach to incoherent signal detection
in multi-element antenna array are researched and modeled. Two
types of useful signals with unknown wavefront were considered:
first one, deterministic (Barker code), and second one, random
(Gaussian distribution). The derivation of the sufficient statistics took
into account the linearity of the antenna array. The performance
characteristics and detecting curves are modeled and compared for
different useful signals parameters and for different number of
elements of the antenna array. Results of researches in case of some
additional conditions can be applied to a digital communications
systems.
Abstract: We present probabilistic multinomial Dirichlet
classification model for multidimensional data and Gaussian process
priors. Here, we have considered efficient computational method that
can be used to obtain the approximate posteriors for latent variables
and parameters needed to define the multiclass Gaussian process
classification model. We first investigated the process of inducing a
posterior distribution for various parameters and latent function by
using the variational Bayesian approximations and important sampling
method, and next we derived a predictive distribution of latent
function needed to classify new samples. The proposed model is
applied to classify the synthetic multivariate dataset in order to verify
the performance of our model. Experiment result shows that our model
is more accurate than the other approximation methods.
Abstract: Privacy is sacred and would normally be expected and preserved by an individual. Online privacy is no longer about the right to be left alone, but also includes the right not to be monitored. However, with the revelations made by United States National Security Agency former employee Edward Snowden that the government is spying on internet communications, individuals’ privacy can no longer be expected. Therefore, this paper is intended to evaluate law related to privacy protection in the digital domain, who should govern it and whether invasion to a person’s privacy is a necessary justification to preserve national security.
Abstract: This paper introduces an effective method of
segmenting Korean text (place names in Korean) from a Korean road
sign image. A Korean advanced directional road sign is composed of
several types of visual information such as arrows, place names in
Korean and English, and route numbers. Automatic classification of
the visual information and extraction of Korean place names from the
road sign images make it possible to avoid a lot of manual inputs to a
database system for management of road signs nationwide. We
propose a series of problem-specific heuristics that correctly segments
Korean place names, which is the most crucial information, from the
other information by leaving out non-text information effectively. The
experimental results with a dataset of 368 road sign images show 96%
of the detection rate per Korean place name and 84% per road sign
image.
Abstract: This paper introduces a signal monitoring program
developed with a view to helping electrical engineering students get
familiar with sensors with digital output. Because the output of digital
sensors cannot be simply monitored by a measuring instrument such as
an oscilloscope, students tend to have a hard time dealing with digital
sensors. The monitoring program runs on a PC and communicates with
an MCU that reads the output of digital sensors via an asynchronous
communication interface. Receiving the sensor data from the MCU,
the monitoring program shows time and/or frequency domain plots of
the data in real time. In addition, the monitoring program provides a
serial terminal that enables the user to exchange text information with
the MCU while the received data is plotted. The user can easily
observe the output of digital sensors and configure the digital sensors
in real time, which helps students who do not have enough experiences
with digital sensors. Though the monitoring program was programmed
in the Matlab programming language, it runs without the Matlab since
it was compiled as a standalone executable.
Abstract: Password authentication is one of the widely used
methods to achieve authentication for legal users of computers and
defense against attackers. There are many different ways to
authenticate users of a system and there are many password cracking
methods also developed. This paper proposes how best password
cracking can be performed on a CPU-GPGPU based system. The
main objective of this work is to project how quickly a password can
be cracked with some knowledge about the computer security and
password cracking if sufficient security is not incorporated to the
system.
Abstract: Thermoacoustic refrigerator is a cooling device which
uses the acoustic waves to produce the cooling effect. The aim of this
paper is to explore the experimental and numerical feasibility of a
standing-wave thermoacoustic refrigerator. The effects of the stack
length, position of stack and operating frequency on the cooling
performance are carried out. The circular pore stacks are tested under
the atmospheric pressure. A low-cost loudspeaker is used as an
acoustic driver. The results show that the location of stack installed in
resonator tube has a greater effect on the cooling performance, than
the stack length and operating frequency, respectively. The
temperature difference across the ends of stack can be generated up
to 13.7°C, and the temperature of cold-end is dropped down by 5.3°C
from the ambient temperature.
Abstract: A seizure prediction method is proposed by extracting
global features using phase correlation between adjacent epochs for
detecting relative changes and local features using fluctuation/
deviation within an epoch for determining fine changes of different
EEG signals. A classifier and a regularization technique are applied
for the reduction of false alarms and improvement of the overall
prediction accuracy. The experiments show that the proposed method
outperforms the state-of-the-art methods and provides high prediction
accuracy (i.e., 97.70%) with low false alarm using EEG signals in
different brain locations from a benchmark data set.
Abstract: The purpose of the study is to investigate the level of
intrinsic motivation of trainers after attending a Continuous
Professional Development Course (CPD) organized by Institute of
Teacher Training Malaysia titled, “Transformation of Teaching and
Learning the Fun Way”. This study employed a survey whereby 96
teacher trainers were given Situational Intrinsic Motivational Scale
(SIMS) Instruments. Confirmatory factor analysis was carried out to
get the validity of this instrument in local setting. Data were analyzed
with SPSS for descriptive statistic. Semi- structured interviews were
also administrated to collect qualitative data on participants’
experiences after participating in the two-day fun-filled program. The
findings showed that the participants’ level of intrinsic motivation
showed higher mean than the amotivation. The results revealed that
the intrinsic motivation mean is 19.0 followed by Identified
regulation with a mean of 17.4, external regulation 9.7 and
amotivation 6.9. The interview data also revealed that the participants
were motivated after attending this training program. It can be
concluded that this program, which was organized by Institute of
Teacher Training Malaysia, was able to enhance participants’ level of
motivation. Self-Determination Theory (SDT) as a multidimensional
approach to motivation was utilized. Therefore, teacher trainers may
have more success using the “The fun way approach” in conducting
training program in future.
Abstract: The power electronic components within Electric Vehicles (EV) need to operate in several important modes. Some modes directly influence safety, while others influence vehicle performance. Given the variety of functions and operational modes required of the power electronics, it needs to meet efficiency requirements to minimize power losses. Another challenge in the control and construction of such systems is the ability to support bidirectional power flow. This paper considers the construction, operation, and feasibility of available converters for electric vehicles with feasible configurations of electrical buses and loads. This paper describes logic and control signals for the converters for different operations conditions based on the efficiency and energy usage bases.
Abstract: The transesterification of dimethyl malonate (DMM)
with phenol has been studied in vapour phase over cordierite
honeycomb coated with solid acid catalysts such as ZrO2,
Mo(VI)/ZrO2 and SO42-/ZrO2. The catalytic materials were prepared
honeycomb coated, powder forms, and characterized for their total
surface acidity by NH3-TPD and crystalinity by powder XRD
methods. Phenyl methyl malonate (PMM) and diphenyl malonate
(DPM) were obtained as the reaction products. A good conversion of
DMM (up to 82%) of MPM with 95% selectivity was observed when
the reactions were carried out at a catalyst bed temperature of 200 °C
and flow-rate of 10 mL/h in presence of Mo(VI)/ZrO2 as catalyst.
However, over SO4^2-/ZrO2 catalyst, the yield of DPM was found to be
higher. The results have been interpreted based on the variation of
acidic properties and powder XRD phases of zirconia on
incorporation of Mo(VI) or SO42– ions. Transesterification reactions
were also carried out over powder forms of the catalytic materials
and the yield of the desired phenyl ester products were compared
with that of the HC coated catalytic materials. The solid acids were
found to be reusable when used for at least 5 reaction cycles.
Abstract: Considering the challenges of short product life cycles
and growing variant diversity, cost minimization and manufacturing
flexibility increasingly gain importance to maintain a competitive
edge in today’s global and dynamic markets. In this context, an
aerodynamic part feeding system for high-speed industrial assembly
applications has been developed at the Institute of Production
Systems and Logistics (IFA), Leibniz Universitaet Hannover. The
aerodynamic part feeding system outperforms conventional systems
with respect to its process safety, reliability, and operating speed. In
this paper, a multi-objective optimisation of the aerodynamic feeding
system regarding the orientation rate, the feeding velocity, and the
required nozzle pressure is presented.
Abstract: Much of the literature on research design has focused
on research conducted in developed, uni-cultural or primarily English
speaking countries. Studies of qualitative case study research, the
challenges, and prospects have been embedded in Western/Eurocentric
society and social theories. Although there have been some
theoretical studies, few empirical studies have been conducted to
explore the nature of the challenges of qualitative case study in
developing countries. These challenges include accessibility to
organizations, conducting interviews in developing countries,
accessing documents and observing official meetings, language and
cultural challenges, the use of consent forms, issues affecting access
to companies, respondent issues, and data analysis. The author, while
conducting qualitative case study research in Libya, faced all these
issues. The discussion in this paper examines these issues in order to
make a contribution toward the literature in this area.
Abstract: A model to predict the plastic zone size for material
under plane stress condition has been developed and verified
experimentally. The developed model is a function of crack size,
crack angle and material property (dislocation density). Simulation
and validation results show that the model developed show good
agreement with experimental results. Samples of low carbon steel
(0.035%C) with included surface crack angles of 45o, 50o, 60o, 70o
and 90o and crack depths of 2mm and 4mm were subjected to low
strain rate between 0.48 x 10-3 s-1 – 2.38 x 10-3 s-1. The mechanical
properties studied were ductility, tensile strength, modulus of
elasticity, yield strength, yield strain, stress at fracture and fracture
toughness. The experimental study shows that strain rate has no
appreciable effect on the size of plastic zone while crack depth and
crack angle plays an imperative role in determining the size of the
plastic zone of mild steel materials.
Abstract: Concurrent planning of project scheduling and
material ordering has been increasingly addressed within last decades
as an approach to improve the project execution costs. Therefore, we
have taken the problem into consideration in this paper, aiming to
maximize schedules quality robustness, in addition to minimize the
relevant costs. In this regard, a bi-objective mathematical model is
developed to formulate the problem. Moreover, it is possible to
utilize the all-unit discount for materials purchasing. The problem is
then solved by the E-constraint method, and the Pareto front is
obtained for a variety of robustness values. The applicability and
efficiency of the proposed model is tested by different numerical
instances, finally.