Abstract: Excessive vibration means increased wear, increased
repair efforts, bad product selection & quality and high energy
consumption. This may be sometimes experienced by cavitation or
suction/discharge recirculation which could occur only when net
positive suction head available NPSHA drops below the net positive
suction head required NPSHR. Cavitation can cause axial surging, if it
is excessive, will damage mechanical seals, bearings, possibly other
pump components frequently, and shorten the life of the impeller.
Efforts have been made to explain Suction Energy (SE), Specific
Speed (Ns), Suction Specific Speed (Nss), NPSHA, NPSHR & their
significance, possible reasons of cavitation /internal recirculation, its
diagnostics and remedial measures to arrest and prevent cavitation in
this paper. A case study is presented by the author highlighting that
the root cause of unwanted noise and vibration is due to cavitation,
caused by high specific speeds or inadequate net- positive suction
head available which results in damages to material surfaces of
impeller & suction bells and degradation of machine performance, its
capacity and efficiency too. Author strongly recommends revisiting
the technical specifications of CW pumps to provide sufficient NPSH
margin ratios >1.5, for future projects and Nss be limited to 8500 -
9000 for cavitation free operation.
Abstract: A combined heat and power (CHP) system is an efficient and clean way to generate power (electricity). Heat produced by the CHP system can be used for water and space heating. The CHP system which uses hydrogen as fuel produces zero carbon emission. Its’ efficiency can reach more than 80% whereas that of a traditional power station can only reach up to 50% because much of the thermal energy is wasted. The other advantages of CHP systems include that they can decentralize energy generation, improve energy security and sustainability, and significantly reduce the energy cost to the users. This paper presents the economic benefits of using a CHP system in the domestic environment. For this analysis, natural gas is considered as potential fuel as the hydrogen fuel cell based CHP systems are rarely used. UK government incentives for CHP systems are also considered as the added benefit. Results show that CHP requires a significant initial investment in returns it can reduce the annual energy bill significantly. Results show that an investment may be paid back in 7 years. After the back period, CHP can run for about 3 years as most of the CHP manufacturers provide 10 year warranty.
Abstract: This paper presents a fault-tolerant implementation for
adder schemes using the dual duplication code. To prove the
efficiency of the proposed method, the circuit is simulated in double
pass transistor CMOS 32nm technology and some transient faults are
voluntary injected in the Layout of the circuit. This fully differential
implementation requires only 20 transistors which mean that the
proposed design involves 28.57% saving in transistor count
compared to standard CMOS technology.
Abstract: Nanotechnology in pristine sense refers to building of
structures at atomic and molecular scale. Meticulously
nanotechnology encompasses the nanomaterials with at least one
dimension size ranging from 1 to 100 nanometres. Unlike the literal
meaning of its name, nanotechnology is a massive concept beyond
imagination. This paper predominantly deals with relevance of
nanotechnology in automotive industries. New generation of
automotives looks at nanotechnology as an emerging trend of
manufacturing revolution. Intricate shapes can be made out of fairly
inexpensive raw materials instead of conventional fabrication
process. Though the current era have enough technology to face
competition, nanotechnology can give futuristic implications to pick
up the modern pace. Nanotechnology intends to bridge the gap
between automotives with superior technical performance and their
cost fluctuation. Preliminarily, it is an area of great scientific interest
and a major shaper of many new technologies. Nanotechnology can
be an ideal building block for automotive industries, under constant
evolution offering a very wide scope of activity. It possesses huge
potential and is still in the embryonic form of research and
development.
Abstract: E-government has been adopted and used by many governments/countries around the world including Ghana to provide citizens and businesses with more accurate, real-time, and high quality services and information. The objective of this paper is to present an overview of the Government of Ghana’s (GoG) adoption and implement of e-government and its usage by the Ministries, Departments and its agencies (MDAs) as well as other public sector institutions to deliver efficient public service to the general public i.e. citizens, business etc. Government implementation of e-government focused on facilitating effective delivery of government service to the public and ultimately to provide efficient government-wide electronic means of sharing information and knowledge through a network infrastructure developed to connect all major towns and cities, Ministries, Departments and Agencies and other public sector organizations in Ghana. One aim for the Government of Ghana use of ICT in public administration is to improve productivity in government administration and service by facilitating exchange of information to enable better interaction and coordination of work among MDAs, citizens and private businesses. The study was prepared using secondary sources of data from government policy documents, national and international published reports, journal articles, and web sources. This study indicates that through the e-government initiative, currently citizens and businesses can access and pay for services such as renewal of driving license, business registration, payment of taxes, acquisition of marriage and birth certificates as well as application for passport through the GoG electronic service (eservice) and electronic payment (epay) portal. Further, this study shows that there is enormous commitment from GoG to adopt and implement e-government as a tool not only to transform the business of government but also to bring efficiency in public services delivered by the MDAs. To ascertain this, a further study need to be carried out to determine if the use of e-government has brought about the anticipated improvements and efficiency in service delivery of MDAs and other state institutions in Ghana.
Abstract: In order to study the Mutual effect of genotype ×
environment for the percent of oil index in sunflower items, an
experiment was accomplished form complete random block designs
in four iteration and was four diverse researching station comprising
Esfahan, Birjand, Sari, and Karaj. Complex variance analysis showed
that there is an important diversity between the items under
investigation. The results relevant the coefficient variation of items
Azargol and Vidoc has respectively allocated the minimum
coefficient of variations. According to the results extrapolated from
Shokla stability variance, the Items Brocar, Allison and Fabiola, are
among the stable genotypes for oil percent respectively. In the biplot
GGE, the location under investigations divided in two superenvironments,
first one comprised of locations naming Esfahan,
Karaj, and Birjand, and second one were such a location as Sari. By
this point of view, in the first super-environment, the Item Fabiola
and in the second Almanzor item was among the best items and
crops.
Abstract: Energy has a prominent role for development of
nations. Countries which have energy resources also have strategic
power in the international trade of energy since it is essential for all
stages of production in the economy. Thus, it is important for
countries to analyze the weaknesses and strength of the system. On
the other side, international trade is one of the fields that are analyzed
as a complex network via network analysis. Complex network is one
of the tools to analyze complex systems with heterogeneous agents
and interaction between them. A complex network consists of nodes
and the interactions between these nodes. Total properties which
emerge as a result of these interactions are distinct from the sum of
small parts (more or less) in complex systems. Thus, standard
approaches to international trade are superficial to analyze these
systems. Network analysis provides a new approach to analyze
international trade as a network. In this network, countries constitute
nodes and trade relations (export or import) constitute edges. It
becomes possible to analyze international trade network in terms of
high degree indicators which are specific to complex networks such
as connectivity, clustering, assortativity/disassortativity, centrality,
etc. In this analysis, international trade of crude oil and coal which
are types of fossil fuel has been analyzed from 2005 to 2014 via
network analysis. First, it has been analyzed in terms of some
topological parameters such as density, transitivity, clustering etc.
Afterwards, fitness to Pareto distribution has been analyzed via
Kolmogorov-Smirnov test. Finally, weighted HITS algorithm has
been applied to the data as a centrality measure to determine the real
prominence of countries in these trade networks. Weighted HITS
algorithm is a strong tool to analyze the network by ranking countries
with regards to prominence of their trade partners. We have
calculated both an export centrality and an import centrality by
applying w-HITS algorithm to the data. As a result, impacts of the
trading countries have been presented in terms of high-degree
indicators.
Abstract: In order to retrieve images efficiently from a large
database, a unique method integrating color and texture features
using genetic programming has been proposed. Opponent color
histogram which gives shadow, shade, and light intensity invariant
property is employed in the proposed framework for extracting color
features. For texture feature extraction, fast discrete curvelet
transform which captures more orientation information at different
scales is incorporated to represent curved like edges. The recent
scenario in the issues of image retrieval is to reduce the semantic gap
between user’s preference and low level features. To address this
concern, genetic algorithm combined with relevance feedback is
embedded to reduce semantic gap and retrieve user’s preference
images. Extensive and comparative experiments have been conducted
to evaluate proposed framework for content based image retrieval on
two databases, i.e., COIL-100 and Corel-1000. Experimental results
clearly show that the proposed system surpassed other existing
systems in terms of precision and recall. The proposed work achieves
highest performance with average precision of 88.2% on COIL-100
and 76.3% on Corel, the average recall of 69.9% on COIL and 76.3%
on Corel. Thus, the experimental results confirm that the proposed
content based image retrieval system architecture attains better
solution for image retrieval.
Abstract: The out-of-band impedance environment is considered
to be of paramount importance in engineering the in-band impedance
environment. Presenting the frequency independent and constant outof-
band impedances across the wide modulation bandwidth is
extremely important for reliable device characterization for future
wireless systems. This paper presents an out-of-band impedance
optimization scheme based on simultaneous engineering of
significant baseband components IF1 (twice the modulation
frequency) and IF2 (four times the modulation frequency) and higher
baseband components such as IF3 (six times the modulation
frequency) and IF4 (eight times the modulation frequency) to
engineer the in-band impedance environment. The investigations
were carried out on a 10W GaN HEMT device driven to deliver a
peak envelope power of approximately 40.5dBm under modulated
excitation. The presentation of frequency independent baseband
impedances to all the significant baseband components whilst
maintaining the optimum termination for fundamental tones as well
as reactive termination for 2nd harmonic under class-J mode of
operation has outlined separate optimum impedances for best
intermodulation (IM) linearity.
Abstract: The study of the aerodynamics related to the
improvement in the acting of airplanes and automobiles with the
objective of being reduced the effect of the attrition of the air on
structures, providing larger speeds and smaller consumption of fuel.
The application of the knowledge of the aerodynamics not more
limits to the aeronautical and automobile industries. Therefore, this
research aims to design and construction of a wind tunnel to perform
aerodynamic analysis in bodies of cars, seeking greater efficiency.
Therefore, this research aims to design and construction of a wind
tunnel to perform aerodynamic analysis in bodies of cars, seeking
greater efficiency. For this, a methodology for wind tunnel type
selection is designed to be built, taking into account the various
existing configurations in which chose to build an open circuit tunnel,
due to the lower complexity of construction and installation;
operational simplicity and low cost. The guidelines for the project
were teaching: the layer that limits study and analyze specimens with
different geometries. For the variation of pressure in the test, section
of a switched gauge used a pitot tube. Thus, it was possible to obtain
quantitative and qualitative results, which proved to be satisfactory.
Abstract: The use of optical technologies in the
telecommunications has been increasing due to its ability to transmit
large amounts of data over long distances. However, as in all systems
of data transmission, optical communication channels suffer from
undesirable and non-deterministic effects, being essential to know the
same. Thus, this research allows the assessment of these effects, as
well as their characterization and beneficial uses of these effects.
Abstract: Biodiesel is widely investigated to solve the twin
problem of depletion of fossil fuel and environmental degradation.
The main objective of the present work is to compare performance,
emissions, and combustion characteristics of biodiesel derived from
cotton seed oil in a diesel engine with the baseline results of
petrodiesel fuel. Tests have been conducted on a single cylinder, four
stroke CIDI diesel engine with a speed of 1500 rpm and a fixed
compression ratio of 17.5 at different load conditions. The
performance parameters evaluated include brake thermal efficiency,
brake specific fuel consumption, brake power, indicated mean
effective pressure, mechanical efficiency, and exhaust gas
temperature. Regarding combustion study, cylinder pressure, rate of
pressure rise, net heat release rate, cumulative heat release, mean gas
temperature, mass fraction burned, and fuel line pressure were
evaluated. The emission parameters such as carbon monoxide, carbon
dioxide, un-burnt hydrocarbon, oxides of nitrogen, and smoke
opacity were also measured by a smoke meter and an exhaust gas
analyzer and compared with baseline results. The brake thermal
efficiency of cotton seed oil methyl ester (CSOME) was lower than
that of petrodiesel and brake specific fuel consumption was found to
be higher. However, biodiesel resulted in the reduction of carbon
dioxide, un-burnt hydrocarbon, and smoke opacity at the expense of
nitrogen oxides. Carbon monoxide emissions for biodiesel was higher
at maximum output power. It has been found that the combustion
characteristics of cotton seed oil methyl ester closely followed those
of standard petrodiesel. The experimental results suggested that
biodiesel derived from cotton seed oil could be used as a good
substitute to petrodiesel fuel in a conventional diesel without any
modification.
Abstract: This paper proposes an APPLE scheme that aims at providing absolute and proportional throughput guarantees, and maximizing system throughput simultaneously for wireless LANs with homogeneous and heterogenous traffic. We formulate our objectives as an optimization problem, present its exact and approximate solutions, and prove the existence and uniqueness of the approximate solution. Simulations validate that APPLE scheme is accurate, and the approximate solution can well achieve the desired objectives already.
Abstract: The early-stage damage detection in offshore
structures requires continuous structural health monitoring and for the
large area the position of sensors will also plays an important role in
the efficient damage detection. Determining the dynamic behavior of
offshore structures requires dense deployment of sensors. The wired
Structural Health Monitoring (SHM) systems are highly expensive
and always needs larger installation space to deploy. Wireless sensor
networks can enhance the SHM system by deployment of scalable
sensor network, which consumes lesser space. This paper presents the
results of wireless sensor network based Structural Health Monitoring
method applied to a scaled experimental model of offshore structure
that underwent wave loading. This method determines the
serviceability of the offshore structure which is subjected to various
environment loads. Wired and wireless sensors were installed in the
model and the response of the scaled BLSRP model under wave
loading was recorded. The wireless system discussed in this study is
the Raspberry pi board with Arm V6 processor which is programmed
to transmit the data acquired by the sensor to the server using Wi-Fi
adapter, the data is then hosted in the webpage. The data acquired
from the wireless and wired SHM systems were compared and the
design of the wireless system is verified.
Abstract: Multiple Sclerosis (MS) is a disease which affects the
central nervous system and causes balance problem. In clinical, this
disorder is usually evaluated using static posturography. Some linear
or nonlinear measures, extracted from the posturographic data (i.e.
center of pressure, COP) recorded during a balance test, has been
used to analyze postural control of MS patients. In this study, the
trend (TREND) and the sample entropy (SampEn), two nonlinear
parameters were chosen to investigate their relationships with the
expanded disability status scale (EDSS) score. 40 volunteers with
different EDSS scores participated in our experiments with eyes open
(EO) and closed (EC). TREND and 2 types of SampEn (SampEn1
and SampEn2) were calculated for each combined COP’s position
signal. The results have shown that TREND had a weak negative
correlation to EDSS while SampEn2 had a strong positive correlation
to EDSS. Compared to TREND and SampEn1, SampEn2 showed a
better significant correlation to EDSS and an ability to discriminate
the MS patients in the EC case. In addition, the outcome of the study
suggests that the multi-dimensional nonlinear analysis could provide
some information about the impact of disability progression in MS on
dynamics of the COP data.
Abstract: This paper presents the experimental results of 11 kV
and 33 kV silicon composite insulators under artificial salt and urea
polluted conditions. The tests were carried out under different
seasons like summer, winter, and monsoon. The artificial pollution is
prepared by properly dissolving the salt and urea in the water. The
prepared salt and urea pollutions are sprayed on the insulators and
dried up for sufficiently large time. The process is continued until a
uniform layer is formed on the surface of insulator. For each insulator
rating, four samples were tested. The maximum leakage current and
breakdown voltage were measured. From experimental data,
performance of test specimen is evaluated by comparing breakdown
voltage and leakage current during different seasons when exposed to
salt and urea polluted conditions. From these results the performance
of the insulators can be predicted when they are installed in
industrial, agricultural, and coastal areas. The experimental tests were
carried out in the High Voltage laboratory using two stage cascade
transformer having the rating of 1000 kVA, 500 kV.
Abstract: The research aims to investigate the occurrence of
multidrug-resistant Acinetobacter, in carrot and estimate the role of
carrot in its transmission in a rapidly growing urban population.
Thus, 50 carrot samples were collected from Jakara wastewater
irrigation farms and are analyzed on MacConkey agar and screened
by Microbact 24E (Oxoid) and susceptibility of isolates is tested
against 10 commonly used antibiotics. Acinetobacter baumannii and
A. lwoffii were isolated in 22.00% and 16% of samples respectively.
Resistance to ceporex and penicillin of 36.36% and 27.27% in A.
baumannii, and sensitivity to ofloxacin, pefloxacin, gentimycin and
co-trimoxazole were observed. However, for A. lwoffii apart from
37.50% resistance to ceporex, it was also resistant to all other drugs
tested. There were similarities in the resistances shown by A.
baumannii and A. lwoffii to fluoroquinolones and β- lactame drug
families in addition to between sulfonamide and animoglycoside
demonstrated by A. lwoffii. Significant correlation in similarities were
observed at P < 0.05 to CPX to NA (46.2%), and SXT to AU (52.6%)
A. baumannii and A. lwoffii respectively and high multi drug
resistance (MDR) of 27.27% and 62.50% by A. baumannii and A.
lwoffii respectively. The occurrence of multidrug-resistance pathogen
in carrot is a serious challenge to public health care, especially in a
rapidly growing urban population where subsistence agriculture
contributes greatly to urban livelihood and source of vegetables.
Abstract: Fermentation is well known as an essential process to
develop chocolate flavor in dried cocoa beans. Besides developing
the precursor of cocoa flavor, it also induces the color changes in the
beans. The fermentation process is influenced by various factors such
as planting material, preconditioning of cocoa pod and fermentation
technique. Therefore, this study was conducted to evaluate color of
Malaysian cocoa beans and how the duration of pods storage and
fermentation technique using shallow box will effect on its color
characteristics. There are two factors being studied i.e. duration of
cocoa pod storage (0, 2, 4 and 6 days) and duration of cocoa
fermentation (0, 1, 2, 3, 4 and 5 days). The experiment is arranged in
4 x 6 factorial designs with 24 treatments and arrangement is in a
Completely Randomised Design (CRD). The produced beans are
inspected for color changes under artificial light during cut test and
divided into four groups of color namely fully brown, purple brown,
fully purple and slaty. Cut tests indicated that cocoa beans which are
directly dried without undergone fermentation has the highest slaty
percentage. However, application of pods storage before fermentation
process is found to decrease the slaty percentage. In contrast, the
percentages of fully brown beans start to dominate after two days of
fermentation, especially from four and six days of pods storage batch.
Whereas, almost all batches of cocoa beans have a percentage of fully
purple less than 20%. Interestingly, the percentage of purple brown
beans are scattered in the entire beans batch regardless any specific
trend. Meanwhile, statistical analysis using General Linear Model
showed that the pods storage has a significant effect on the color
characteristic of the Malaysian dried beans compared to fermentation
duration.
Abstract: Energy consumption of a hotel can be a hot topic in
smart city; it is difficult to evaluate the contribution of impact factors
to energy consumption of a hotel. Therefore, grasping the key impact
factors has great effect on the energy saving management of a hotel.
Based on the SPIRTPAT model, we establish the identity with the
impact factors of occupancy rate, unit area of revenue, temperature
factor, unit revenue of energy consumption. In this paper, we use the
LMDI (Logarithmic Mean Divisia Index) to decompose the impact
factors of energy consumption of hotel from Jan. to Dec. in 2001. The
results indicate that the occupancy rate and unit area of revenue are the
main factors that can increase unit area of energy consumption, and the
unit revenue of energy consumption is the main factor to restrain the
growth of unit area of energy consumption. When the energy
consumption of hotel can appear abnormal, the hotel manager can
carry out energy saving management and control according to the
contribution value of impact factors.
Abstract: The field of instrumentation electronics is undergoing
an explosive growth, due to its wide range of applications. The
proliferation of electrical devices in a close working proximity can
negatively influence each other’s performance. The degradation in
the performance is due to electromagnetic interference (EMI). This paper investigates the negative effects of electromagnetic
interference originating in the General Purpose Interface Bus (GPIB)
control-network of the AC-DC transfer measurement system.
Remedial measures of reducing measurement errors and failure of
range of industrial devices due to EMI have been explored. The ACDC
transfer measurement system was analysed for the commonmode
(CM) EMI effects. Further investigation of coupling path as
well as much accurate identification of noise propagation mechanism
has been outlined. To prevent the occurrence of common-mode
(ground loops) which was identified between the GPIB system
control circuit and the measurement circuit, a microcontroller-driven
GPIB switching isolator device was designed, prototyped,
programmed and validated. This mitigation technique has been
explored to reduce EMI effectively.