Abstract: This research aims to investigate callus induction,
somatic embryogenesis and indirect plant regeneration of Crassula
ovata (Mill.) Druce – the famous ornamental plant. Experiment no.1:
Callus induction was obtained from leaf and stem explants on
Murashige and Skoog (MS) medium supplemented with various plant
growth regulators (PGRs). Effects of different PGRs, plant
regeneration and subsequent plantlet conversion were also assessed.
Indirect plant regeneration was achieved from the callus of stem
explants by the addition of 1.5 mg/L Kinetin (KN) alone. Best shoot
induction was achieved (6.5 shoots/per explant) after 60 days. For
successful rooting, regenerated plantlets were sub-cultured on the
same MS media supplemented with 1.5 mg/L KN alone. The rooted
plantlets were acclimatized and the survival rate was 90%.
Experiment no.2: Results revealed that 0.5 mg/L 2,4-D alone and in
combination with 1.0 mg/L 6-Benzyladenine (BA) gave 89.8% callus
from the stem explants as compared to leaf explants. Callus
proliferation and somatic embryo formation were also evaluated by
‘Double Staining Method’ and different stages of somatic
embryogenesis were revealed by scanning electron microscope. Full
Strength MS medium produced the highest number (49.6%) of
cotyledonary stage somatic embryos (SEs). Mature cotyledonary
stage SEs developed into plantlets after 12 weeks of culture. Wellrooted
plantlets were successfully acclimatized at the survival rate of
85%. Indirectly regenerated plants did not show any detectable
variation in morphological and growth characteristics when
compared with the donor plant.
Abstract: Nonstandard tests are necessary for analyses and
verification of new developed structural and technological solutions
with application of composite materials. One of the most critical
primary structural parts of a typical aerospace structure is T-joint.
This structural element is loaded mainly in shear, bending, peel and
tension. The paper is focused on the shear loading simulations. The
aim of the work is to obtain a representative uniform distribution of
shear loads along T-joint during the mechanical testing. A new
design of T-joint test procedure, numerical simulation and
optimization of representative boundary conditions are presented.
The different conditions and inaccuracies both in simulations and
experiments are discussed. The influence of different parameters on
stress and strain distributions is demonstrated on T-joint made of
CFRP (carbon fibre reinforced plastic). A special test rig designed by
VZLU (Aerospace Research and Test Establishment) for T-shear test
procedure is presented.
Abstract: reliability-based methodology for the assessment
and evaluation of reinforced concrete (R/C) structural elements of
concrete structures is presented herein. The results of the reliability
analysis and assessment for R/C structural elements were verified by
the results obtained through deterministic methods. The outcomes of
the reliability-based analysis were compared against currently
adopted safety limits that are incorporated in the reliability indices
β’s, according to international standards and codes. The methodology
is based on probabilistic analysis using reliability concepts and
statistics of the main random variables that are relevant to the subject
matter, and for which they are to be used in the performance-function
equation(s) associated with the structural elements under study.
These methodology techniques can result in reliability index β, which
is commonly known as the reliability index or reliability measure
value that can be utilized to assess and evaluate the safety, human
risk, and functionality of the structural component. Also, these
methods can result in revised partial safety factor values for certain
target reliability indices that can be used for the purpose of
redesigning the R/C elements of the building and in which they could
assist in considering some other remedial actions to improve the
safety and functionality of the member.
Abstract: Innovations not only contribute to competitiveness of
the company but have also positive effects on revenues. On average,
product innovations account to 14 percent of companies’ sales.
Innovation management has substantially changed during the last
decade, because of growing reliance on external partners. As a
consequence, a new task for purchasing arises, as firms need to
understand which suppliers actually do have high potential
contributing to the innovativeness of the firm and which do not.
Proper organization of the purchasing function is important since
for the majority of manufacturing companies deal with substantial
material costs which pass through the purchasing function. In the past
the purchasing function was largely seen as a transaction-oriented,
clerical function but today purchasing is the intermediate with supply
chain partners contributing to innovations, be it product or process
innovations. Therefore, purchasing function has to be organized
differently to enable firm innovation potential.
However, innovations are inherently risky. There are behavioral
risk (that some partner will take advantage of the other party),
technological risk in terms of complexity of products and processes
of manufacturing and incoming materials and finally market risks,
which in fact judge the value of the innovation. These risks are
investigated in this work. Specifically, technological risks which deal
with complexity of the products, and processes will be investigated
more thoroughly. Buying components or such high edge technologies
necessities careful investigation of technical features and therefore is
usually conducted by a team of experts. Therefore it is hypothesized
that higher the technological risk, higher will be the centralization of
the purchasing function as an interface with other supply chain
members.
Main contribution of this research lies is in the fact that analysis
was performed on a large data set of 1493 companies, from 25
countries collected in the GMRG 4 survey. Most analyses of
purchasing function are done by case study analysis of innovative
firms. Therefore this study contributes with empirical evaluations that
can be generalized.
Abstract: The research focus on study, analyze and design the
model of the infrastructure and computer networks for distance
education, online learning via new media, e-learning and blended
learning. The collected information from study and analyze process
that information was evaluated by the index of item objective
congruence (IOC) by 9 specialists to design model. The results of
evaluate the model with the mean and standard deviation by the
sample of 9 specialists value is 3.85. The results showed that the
infrastructure and computer networks are designed to be appropriate
to a great extent appropriate to a great extent.
Abstract: The main aim of this research was to investigate the
perspectives of English language teachers and learners on the effect
of test techniques on reading comprehension, test performance and
assessment. The research has also aimed at finding the differences
between teacher and learner perspectives, specifying the test
techniques which have the highest effect, investigating the other
factors affecting reading comprehension, and comparing the results
with the similar studies. In order to achieve these objectives,
perspectives and findings of different researchers were reviewed, two
different questionnaires were prepared to collect data for the
perspectives of teachers and learners, the questionnaires were applied
to 26 learners and 8 teachers from the University of Batna (Algeria),
and quantitative and qualitative data analysis of the results were
done. The results and analysis of the results show that different test
techniques affect reading comprehension, test performance and
assessment at different percentages rates.
Abstract: The use of IT equipment has become a part of every
day. However, each device that is part of cyberspace should be
secured against unauthorized use. It is very important to know the
basics of these security devices, but also the basics of safe conduct
their owners. This information should be part of every curriculum
computer science education in primary and secondary schools.
Therefore, the work focuses on the education of pupils in primary and
secondary schools on the Internet. Analysis of the current state
describes approaches to the education of pupils in security issues on
the Internet. The paper presents a questionnaire-based survey which
was carried out in the Czech Republic, whose task was to ascertain
the level of opinion pupils in primary and secondary schools on the
issue of communication in social networks. The research showed that
awareness of socio-pathological phenomena on the Internet
environment is very low. Based on the results it was proposed
appropriate ways of teaching to this issue and its inclusion a proposal
of curriculum for primary and secondary schools.
Abstract: This paper is concerning the issues of behaviour of
lightweight expanded clay aggregates concrete exposed to high
temperature. Lightweight aggregates from expanded clay are
produced by firing of row material up to temperature 1050°C.
Lightweight aggregates have suitable properties in terms of volume
stability, when exposed to temperatures up to 1050°C, which could
indicate their suitability for construction applications with higher risk
of fire. The test samples were exposed to heat by using the standard
temperature-time curve ISO 834. Negative changes in resulting
mechanical properties, such as compressive strength, tensile strength,
and flexural strength were evaluated. Also visual evaluation of the
specimen was performed. On specimen exposed to excessive heat, an
explosive spalling could be observed, due to evaporation of
considerable amount of unbounded water from the inner structure of
the concrete.
Abstract: This paper involved the performance of a hightemperature
X-Ray powder diffraction analysis (XRD) of a sample of
chemical gypsum generated in the production of titanium white; this
gypsum originates by neutralizing highly acidic water with limestone
suspension. Specifically, it was gypsum formed in the first stage of
neutralization when the resulting material contains, apart from
gypsum, a number of waste products resulting from the
decomposition of ilmenite by sulphuric acid. So it can be described as
red titanogypsum. By conducting the experiment using XRD
apparatus Bruker D8 Advance with a Cu anode (λkα=1.54184 Å)
equipped with high-temperature chamber Anton Paar HTK 16, it was
possible to identify clearly in the sample each phase transition in the
system of CaSO4·xH2O.
Abstract: In this paper, thick walled Cylindrical tanks or tubes
made of functionally graded material under internal pressure and
temperature gradient are studied. Material parameters have been
considered as power functions. They play important role in the
elastoplastic behavior of these materials. To clarify their role,
different materials with different parameters have been used under
temperature gradient. Finally, their effect and loading effect have
been determined in first yield point. Also, the important role of
temperature gradient was also shown. At the end the study has been
results obtained from changes in the elastic modulus and yield stress.
Also special attention is also given to the effects of this internal
pressure and temperature gradient in the creation of tensile and
compressive stresses.
Abstract: This research focuses on the optimization of glazed
surfaces and the assessment of possible solar gains in industrial
buildings. Existing window rating methods for single windows were
evaluated and a new method for a simple analysis of energy gains and
losses by single windows was introduced. Furthermore extensive
transient building simulations were carried out to appraise the
performance of low cost polycarbonate multi-cell sheets in
interaction with typical buildings for industrial applications. Mainly
energy saving potential was determined by optimizing the orientation
and area of such glazing systems in dependency on their thermal
qualities. Moreover the impact on critical aspects such as summer
overheating and daylight illumination was considered to ensure the
user comfort and avoid additional energy demand for lighting or
cooling. Hereby the simulated heating demand could be reduced by
up to 1/3 compared to traditional architecture of industrial halls using
mainly skylights.
Abstract: Novel bio-based polymer electrolyte was synthesized
with LiClO4 as the main source of charge carrier. Initially,
polyurethane-LiClO4 polymer electrolytes were synthesized via
prepolymerization method with different NCO/OH ratios and labelled
them as PU1, PU2, PU3 and PU4. Fourier transform infrared (FTIR)
analysis indicates the co-ordination between Li+ ion and polyurethane
in PU1. Differential scanning calorimetry (DSC) analysis indicates
PU1 has the highest glass transition temperature (Tg) corresponds to
the most abundant urethane group which is the hard segment in PU1.
Scanning electron microscopy (SEM) shows the good miscibility
between lithium salt and the polymer. The study found that PU1
possessed the greatest ionic conductivity and the lowest activation
energy, Ea. All the polyurethanes exhibited linear Arrhenius
variations indicating ion transport via simple lithium ion hopping in
polyurethane. This research proves the NCO content in polyurethane
plays an important role in affecting the ionic conductivity of this
polymer electrolyte.
Abstract: The effect of trucks on the level of service is
determined by considering passenger car equivalents (PCE) of trucks.
The current version of Highway Capacity Manual (HCM) uses a
single PCE value for all tucks combined. However, the composition
of truck traffic varies from location to location; therefore, a single
PCE value for all trucks may not correctly represent the impact of
truck traffic at specific locations. Consequently, present study
developed separate PCE values for single-unit and combination
trucks to replace the single value provided in the HCM on different
freeways. Site specific PCE values, were developed using concept of
spatial lagging headways (that is the distance between rear bumpers
of two vehicles in a traffic stream) measured from field traffic data.
The study used data from four locations on a single urban freeway
and three different rural freeways in Indiana. Three-stage-leastsquares
(3SLS) regression techniques were used to generate models
that predicted lagging headways for passenger cars, single unit trucks
(SUT), and combination trucks (CT). The estimated PCE values for
single-unit and combination truck for basic urban freeways (level
terrain) were: 1.35 and 1.60, respectively. For rural freeways the
estimated PCE values for single-unit and combination truck were:
1.30 and 1.45, respectively. As expected, traffic variables such as
vehicle flow rates and speed have significant impacts on vehicle
headways. Study results revealed that the use of separate PCE values
for different truck classes can have significant influence on the LOS
estimation.
Abstract: Polyethylene (PE), Polypropylene (PP), Polyethylene
(vinyl acetate) (EVA) and PE-ionomer nanocomposite samples were
prepared by mixing of the polymer with organofilized
montmorillonite fillers Cloisite 93A and Dellite 67G. The amount of
each modified montmorillonite (MMT) was fixed to 5% (w/w). The
twin-screw kneader was used for the compounding of polymer matrix
and chosen nanofillers. The level of MMT exfoliation was studied by
the transmission electron microscopy (TEM) observations. The
mechanical properties of prepared materials were evaluated by
dynamical mechanical analysis at 30°C and by the measurement of
tensile properties (stress and strain at break).
Abstract: This study is an attempt to raise the awareness of the
stakeholders and the authorities on the sensitivity of Algerian
secondary school teachers of English as a Foreign Language about
the students’ loss of English language skills learned during formal
schooling with effort and at expense and the supposed measures to
arrest that loss. Data was collected from secondary school teachers of
EFL and analyzed quantitatively using a questionnaire containing
open-ended and close-ended questions. The results advocate a
consensus about the need for actions to be adopted to make
assessment techniques outcome-oriented. Most of the participants
were in favor of including curricular activities involving
contextualized learning, problem-solving learning critical selfawareness,
self and peer-assisted learning, use of computers and
internet so as to make learners autonomous.
Abstract: This paper presents a new method to design nonlinear
feedback linearization controller for PEMFCs (Polymer Electrolyte
Membrane Fuel Cells). A nonlinear controller is designed based on
nonlinear model to prolong the stack life of PEMFCs. Since it is
known that large deviations between hydrogen and oxygen partial
pressures can cause severe membrane damage in the fuel cell,
feedback linearization is applied to the PEMFC system so that the
deviation can be kept as small as possible during disturbances or load
variations. To obtain an accurate feedback linearization controller,
tuning the linear parameters are always important. So in proposed
study NSGA (Non-Dominated Sorting Genetic Algorithm)-II method
was used to tune the designed controller in aim to decrease the
controller tracking error. The simulation result showed that the
proposed method tuned the controller efficiently.
Abstract: Ongoing landscape transformation is one of the major
causes behind disappearance of traditional landscapes, and lead to
species and resource loss. Tree in paddy fields in the northeast of
Thailand is one of those traditional landscapes. Using three different
historical time layers, we acknowledged the severe deforestation and
rapid urbanization happened in the region. Despite the general
thinking of decline in tree density as consequences, the heterogeneous
trend of changes in total tree density in three studied landscapes denied
the hypothesis that number of trees in paddy field depend on the length
of land use practice. On the other hand, due to selection of planting
new trees on levees, existence of trees in paddy field now relies on
their values for human use. Besides, changes in land use and landscape
structure had a significant impact on decision of which tree density
level is considered as suitable for the landscape.
Abstract: The majority of contemporary insulation materials
commonly used in the building industry is made from non-renewable
raw materials; furthermore, their production often brings high energy
costs. A long-term trend as far as sustainable development is
concerned has been the reduction of energy and material demands of
building material production. One of the solutions is the possibility of
using easily renewable natural raw material sources which are
considerably more ecological and their production is mostly less
energy-consuming compared to the production of normal insulations
(mineral wool, polystyrene). The paper describes the results of
research focused on the development of thermal and acoustic
insulation materials based on natural fibres intended for floor
constructions. Given the characteristic open porosity of natural fibre
materials, the hygrothermal behaviour of the developed materials was
studied. Especially the influence of relative humidity and temperature
on thermal insulation properties was observed.
Abstract: The effect of Zn2+, Mg2+, and Ba2+ on Saccharomyces
pastorianus performance was evaluated in this study at independent
and three variable combinations. After 96 h of fermentation, high
wort fermentability (%F) = 29.53 was obtained in medium containing
900:4 ppm Mg2+ + Ba2+. Increased ethanol yield 7.35 %(v/v) and
7.13 %(v/v) were obtained in media containing 900:4 ppm Mg2+ +
Ba2+ and 12:900 ppm Zn2+ + Mg2+. Decrease %F = 22.54 and ethanol
yield 6.18 % (v/v) was obtained in medium containing 12:4 ppm Zn2+
+ Ba2+. In media containing the individual ions, increased %F =
27.94 and 26.03 were recorded for media containing 700 ppm Mg2+
and 2 ppm Ba2+ , with ethanol yield of 7.88% (v/v) and 7.62% (v/v)
respectively. Reduced %F and ethanol yield was observed for 10 ppm
Zn2+ and 4 ppm Ba2+ media. The impact of Ba2+ at 1 and 2 ppm was
significant.
Abstract: This study was conducted to evaluate the manganese
removal from aqueous solution using Banana peels activated carbon
(BPAC). Batch experiments have been carried out to determine the
influence of parameters such as pH, biosorbent dose, initial metal ion
concentrations and contact times on the biosorption process. From
these investigations, a significant increase in percentage removal of
manganese 97.4% is observed at pH value 5.0, biosorbent dose 0.8 g,
initial concentration 20 ppm, temperature 25 ± 2°C, stirring rate 200
rpm and contact time 2h. The equilibrium concentration and the
adsorption capacity at equilibrium of the experimental results were
fitted to the Langmuir and Freundlich isotherm models; the Langmuir
isotherm was found to well represent the measured adsorption data
implying BPAC had heterogeneous surface. A raw groundwater
samples were collected from Baharmos groundwater treatment plant
network at Embaba and Manshiet Elkanater City/District-Giza,
Egypt, for treatment at the best conditions that reached at first phase
by BPAC. The treatment with BPAC could reduce iron and
manganese value of raw groundwater by 91.4% and 97.1%,
respectively and the effect of the treatment process on the
microbiological properties of groundwater sample showed decrease
of total bacterial count either at 22°C or at 37°C to 85.7% and 82.4%,
respectively. Also, BPAC was characterized using SEM and FTIR
spectroscopy.