Abstract: One of the key aspects of power quality improvement
in power system is the mitigation of voltage sags/swells and flicker.
Custom power devices have been known as the best tools for voltage
disturbances mitigation as well as reactive power compensation.
Dynamic Voltage Restorer (DVR) which is the most efficient and
effective modern custom power device can provide the most
commercial solution to solve several problems of power quality in
distribution networks. This paper deals with analysis and simulation
technique of DVR based on instantaneous power theory which is a
quick control to detect signals. The main purpose of this work is to
remove three important disturbances including voltage sags/swells
and flicker. Simulation of the proposed method was carried out on
two sample systems by using Matlab software environment and the
results of simulation show that the proposed method is able to
provide desirable power quality in the presence of wide range of
disturbances.
Abstract: An unconventional composite inorganic ceramic
membrane capable of enhancing carbon dioxide emission decline was
fabricated and tested at laboratory scale in conformism to various
environmental guidelines and also to mitigate the effect of global
warming. A review of the existing membrane technologies for carbon
capture including the relevant gas transport mechanisms is presented.
Single gas permeation experiments using silica modified ceramic
membrane with internal diameter 20mm, outside diameter 25mm and
length of 368mm deposited on a macro porous support was carried
out to investigate individual gas permeation behaviours at different
pressures at room temperature. Membrane fabrication was achieved
using after a dip coating method. Nitrogen, Carbon dioxide, Argon,
Oxygen and Methane pure gases were used to investigate their
individual permeation rates at various pressures. Results show that
the gas flow rate increases with pressure drop. However above a
pressure of 3bar, CO2 permeability ratio to that of the other gases
indicated control of a more selective surface adsorptive transport
mechanism.
Abstract: Mangosteen (Garcinia mangostana) pericarp is
considered as agricultural waste and not fully utilized in food
products. It is widely reported that mangosteen pericarp contains high
antioxidant properties. The objective of this study is to develop novel
yellow alkaline noodle (YAN) substituted with different levels of
mangosteen pericarp powder (MPP). YAN formulation was
substituted with different levels of MPP (0%, 5%, 10% and 15%).
The effect on nutritional and antioxidant properties was evaluated.
Higher substitution levels of MPP resulted in significant increase
(p
Abstract: Design concepts of real-time embedded system can be
realized initially by introducing novel design approaches. In this
literature, model based design approach and in-the-loop testing were
employed early in the conceptual and preliminary phase to formulate
design requirements and perform quick real-time verification. The
design and analysis methodology includes simulation analysis, model
based testing, and in-the-loop testing. The design of conceptual driveby-
wire, or DBW, algorithm for electronic control unit, or ECU, was
presented to demonstrate the conceptual design process, analysis, and
functionality evaluation. The concepts of DBW ECU function can be
implemented in the vehicle system to improve electric vehicle, or EV,
conversion drivability. However, within a new development process,
conceptual ECU functions and parameters are needed to be evaluated.
As a result, the testing system was employed to support conceptual
DBW ECU functions evaluation. For the current setup, the system
components were consisted of actual DBW ECU hardware, electric
vehicle models, and control area network or CAN protocol. The
vehicle models and CAN bus interface were both implemented as
real-time applications where ECU and CAN protocol functionality
were verified according to the design requirements. The proposed
system could potentially benefit in performing rapid real-time
analysis of design parameters for conceptual system or software
algorithm development.
Abstract: In this research numerical simulations are performed,
using the multi-relaxation-time lattice Boltzmann method, in the
range 3 ≤ β = w[d] ≤ 30 at Re = 100, 200 and 300, where β the
blockage ratio, w is the equispaced distance between centers of
cylinders, d is the diameter of the cylinder and Re is the Reynolds
number, respectively. Special attention is paid to the effect of the
equispaced distance between centers of cylinders. Visualization of
the vorticity contour visualization are presented for some simulation
showing the flow dynamics and patterns for blockage effect. Results
show that the drag and mean drag coefficients, and Strouhal number,
in general, decrease with the increase of β for fixed Re. It is found
that the decreasing rate of drag and mean drag coefficients and
Strouhal number is more distinct in the range 3 ≤ β ≤ 15. We found
that when β > 15, the blockage effect almost diminishes. Our results
further indicate that the drag and mean drag coefficients, peak value
of the lift coefficient, root-mean-square value of the lift and drag
coefficients and the ratio between lift and drag coefficients decrease
with the increase of Re. The results indicate that symmetry boundary
condition have more blockage effect as compared to periodic
boundary condition.
Abstract: Corrosion of concrete sewer pipes induced by
sulphuric acid attack is a recognised problem worldwide, which is not
only an attribute of countries with hot climate conditions as thought
before. The significance of this problem is by far only realised when
the pipe collapses causing surface flooding and other severe
consequences. To change the existing post-reactive attitude of
managing companies, easy to use and robust models are required to
be developed which currently lack reliable data to be correctly
calibrated. This paper focuses on laboratory experiments of
establishing concrete pipe corrosion rate by submerging samples in to
0.5pH sulphuric acid solution for 56 days under 10ºC, 20ºC and 30ºC
temperature regimes. The result showed that at very early stage of the
corrosion process the samples gained overall mass, at 30ºC the
corrosion progressed quicker than for other temperature regimes,
however with time the corrosion level for 10ºC and 20ºC regimes
tended towards those at 30ºC. Overall, at these conditions the
corrosion rates of 10 mm/year, 13,5 mm/year and 17 mm/year were
observed.
Abstract: Cloud computing is the innovative and leading
information technology model for enabling convenient, on-demand
network access to a shared pool of configurable computing resources
that can be rapidly provisioned and released with minimal
management effort. In this paper, we aim at the development of
workflow management system for cloud computing platforms based
on our previous research on the dynamic allocation of the cloud
computing resources and its workflow process. We took advantage of
the HTML5 technology and developed web-based workflow interface.
In order to enable the combination of many tasks running on the cloud
platform in sequence, we designed a mechanism and developed an
execution engine for workflow management on clouds. We also
established a prediction model which was integrated with job queuing
system to estimate the waiting time and cost of the individual tasks on
different computing nodes, therefore helping users achieve maximum
performance at lowest payment. This proposed effort has the potential
to positively provide an efficient, resilience and elastic environment
for cloud computing platform. This development also helps boost user
productivity by promoting a flexible workflow interface that lets users
design and control their tasks' flow from anywhere.
Abstract: Agro-industry is one of major industries that have
strong impacts on national economic incomes, growth, stability, and
sustainable development. Moreover, this industry also has strong
influences on social, cultural and political issues. Furthermore, this
industry, as producing primary and secondary products, is facing
challenges from such diverse factors such as demand inconsistency,
intense international competition, technological advancements and
new competitors. In order to maintain and to improve industry’s
competitiveness in both domestics and international markets, science
and technology are key factors. Besides hard sciences and
technologies, modern industrial engineering concepts such as Just in
Time (JIT) Total Quality Management (TQM), Quick Response
(QR), Supply Chain Management (SCM) and Lean can be very
effective to support to increase efficiency and effectiveness of these
agricultural products on world stage. Onion is one of Thailand’s
major export products which bring back national incomes. But, it is
also facing challenges in many ways. This paper focused its interests
in onion packing process and its related activities such as storage and
shipment from one of major packing plant and storage in Mae Wang
District, Chiang Mai, Thailand, by applying Toyota Production
System (TPS) or Lean concepts, to improve process capability
throughout the entire packing and distribution process which will be
profitable for the whole onion supply chain. And it will be beneficial
to other related agricultural products in Thailand and other ASEAN
countries.
Abstract: The structures obtained with the use of sandwich
technologies combine low weight with high energy absorbing
capacity and load carrying capacity. Hence, there is a growing and
markedly interest in the use of sandwiches with aluminum foam core
because of very good properties such as flexural rigidity and energy
absorption capability. In the current investigation, the static threepoint
bending tests were carried out on the sandwiches with
aluminum foam core and glass fiber reinforced polymer (GFRP)
skins at different values of support span distances aiming the analyses
of their flexural performance. The influence of the core thickness and
the GFRP skin type was reported in terms of peak load and energy
absorption capacity. For this purpose, the skins with two different
types of fabrics which have same thickness value and the aluminum
foam core with two different thicknesses were bonded with a
commercial polyurethane based flexible adhesive in order to combine
the composite sandwich panels. The main results of the bending tests
are: force-displacement curves, peak force values, absorbed energy,
collapse mechanisms and the effect of the support span length and
core thickness. The results of the experimental study showed that the
sandwich with the skins made of S-Glass Woven fabrics and with the
thicker foam core presented higher mechanical values such as load
carrying and energy absorption capacities. The increment of the
support span distance generated the decrease of the mechanical
values for each type of panels, as expected, because of the inverse
proportion between the force and span length. The most common
failure types of the sandwiches are debonding of the lower skin and
the core shear. The obtained results have particular importance for
applications that require lightweight structures with a high capacity
of energy dissipation, such as the transport industry (automotive,
aerospace, shipbuilding and marine industry), where the problems of
collision and crash have increased in the last years.
Abstract: A field study was conducted to evaluate the efficacy
of lavender for phytoremediation of contaminated soils. The
experiment was performed on an agricultural fields contaminated by
the Non-Ferrous-Metal Works near Plovdiv, Bulgaria. The
concentrations of Pb, Zn and Cd in lavender (roots, stems, leaves and
inflorescences) and in the essential oils of lavender were determined.
Lavender is a plant which is tolerant to heavy metals and can be
grown on contaminated soils, and which can be referred to the
hyperaccumulators of lead and the accumulators of cadmium and
zinc, and can be successfully used in the phytoremediation of heavy
metal contaminated soils. Favorable is also the fact that heavy metals
do not influence the development of the lavender, as well as on the
quality and quantity of the essential oil. The possibility of further
industrial processing will make lavender economically interesting
crops for farmers of phytoextraction technology.
Abstract: Latin hypercube designs (LHDs) have been applied in
many computer experiments among the space-filling designs found in
the literature. A LHD can be randomly generated but a randomly
chosen LHD may have bad properties and thus act poorly in
estimation and prediction. There is a connection between Latin
squares and orthogonal arrays (OAs). A Latin square of order s
involves an arrangement of s symbols in s rows and s columns, such
that every symbol occurs once in each row and once in each column
and this exists for every non-negative integer s. In this paper, a
computer program was written to construct orthogonal array-based
Latin hypercube designs (OA-LHDs). Orthogonal arrays (OAs) were
constructed from Latin square of order s and the OAs constructed
were afterward used to construct the desired Latin hypercube designs
for three input variables for use in computer experiments. The LHDs
constructed have better space-filling properties and they can be used
in computer experiments that involve only three input factors.
MATLAB 2012a computer package (www.mathworks.com/) was
used for the development of the program that constructs the designs.
Abstract: In this paper, an analytical simplified method for
calculating elasto-plastic stresses strains of notched bodies subject to
non-proportional loading paths is discussed. The method was based
on the Neuber notch correction, which relates the incremental elastic
and elastic-plastic strain energy densities at the notch root and the
material constitutive relationship. The validity of the method was
presented by comparing computed results of the proposed model
against finite element numerical data of notched shaft. The
comparison showed that the model estimated notch-root elasto-plastic
stresses strains with good accuracy using linear-elastic stresses. The
prosed model provides more efficient and simple analysis method
preferable to expensive experimental component tests and more
complex and time consuming incremental non-linear FE analysis.
The model is particularly suitable to perform fatigue life and fatigue
damage estimates of notched components subjected to nonproportional
loading paths.
Abstract: Introduction: There are multiple social, individual and
cultural factors that influence an individual’s decision to adopt family
planning methods especially among non-users in patriarchal societies
like Pakistan. Non-users, if targeted efficiently, can contribute
significantly to country’s CPR. A research study showed that nonusers
if convinced to adopt lactational amenorrhea method can shift
to long term methods in future. Research shows that if non users are
targeted efficiently a 59% reduction in unintended pregnancies in
Saharan Africa and South-Central and South-East Asia is anticipated.
Methods: We did secondary data analysis on Pakistan
Demographic Heath Survey (2012-13) dataset. Use of contraception
(never-use/ever-use) was the outcome variable. At univariate level
Chi-square/Fisher Exact test was used to assess relationship of
baseline covariates with contraception use. Then variables to be
incorporated in the model were checked for multicollinearity,
confounding and interaction. Then binary logistic regression (with an
urban-rural stratification) was done to find relationship between
contraception use and baseline demographic and social variables.
Results: The multivariate analyses of the study showed that
younger women (≤ 29 years)were more prone to be never users as
compared to those who were >30 years and this trend was seen in
urban areas (AOR 1.92, CI 1.453-2.536) as well as rural areas (AOR
1.809, CI 1.421-2.303). While looking at regional variation, women
from urban Sindh (AOR 1.548, CI 1.142-2.099) and urban
Balochistan (AOR 2.403, CI 1.504-3.839) had more never users as
compared to other urban regions. Women in the rich wealth quintile
were more never users and this was seen both in urban and rural
localities (urban (AOR 1.106 CI .753-1.624); rural areas (AOR 1.162,
CI .887-1.524)) even though these were not statistically significant.
Women idealizing more children (>4) are more never users as
compared to those idealizing less children in both urban (AOR 1.854,
CI 1.275-2.697) and rural areas (AOR 2.101, CI 1.514-2.916).
Women who never lost a pregnancy were more inclined to be nonusers
in rural areas (AOR 1.394, CI 1.127-1.723) .Women familiar
with only traditional or no method had more never users in rural areas
(AOR 1.717, CI 1.127-1.723) but in urban areas it wasn’t significant.
Women unaware of Lady Health Worker’s presence in their area
were more never users especially in rural areas (AOR 1.276, CI
1.014-1.607). Women who did not visit any care provider were more
never users (urban (AOR 11.738, CI 9.112-15.121) rural areas (AOR
7.832, CI 6.243-9.826)).
Discussion/Conclusion: This study concluded that government,
policy makers and private sector family planning programs should
focus on the untapped pool of never users (younger women from underserved provinces, in higher wealth quintiles, who desire more
children.). We need to make sure to cover catchment areas where
there are less LHWs and less providers as ignorance to modern
methods and never been visited by an LHW are important
determinants of never use. This all is in sync with previous literate
from similar developing countries.
Abstract: Big Data and analytics have gained a huge momentum
in recent years. Big Data feeds into the field of Learning Analytics
(LA) that may allow academic institutions to better understand the
learners’ needs and proactively address them. Hence, it is important
to have an understanding of Big Data and its applications. The
purpose of this descriptive paper is to provide an overview of Big
Data, the technologies used in Big Data, and some of the applications
of Big Data in education. Additionally, it discusses some of the
concerns related to Big Data and current research trends. While Big
Data can provide big benefits, it is important that institutions
understand their own needs, infrastructure, resources, and limitation
before jumping on the Big Data bandwagon.
Abstract: This work sets out to debate the tensions involved in
the processes of contamination and self-purification in the urban
space, particularly in the streams that run through the Buenos Aires
metropolitan area. For much of their course, those streams are piped;
their waters do not come into contact with the outdoors until they
have reached deeply impoverished urban areas with high levels of
environmental contamination. These are peripheral zones that, until
thirty years ago, were marshlands and fields. They are now densely
populated areas largely lacking in urban infrastructure.
The Cárcova neighborhood, where this project is underway, is in
the José León Suárez section of General San Martín county, Buenos
Aires province. A stretch of José León Suarez canal crosses the
neighborhood. Starting upstream, this canal carries pollutants due to
the sewage and industrial waste released into it. Further downstream,
in the neighborhood, domestic drainage is poured into the stream. In
this paper, we formulate a hypothesis diametrical to the one that
holds that these neighborhoods are the primary source of
contamination, suggesting instead that in the stretch of the canal that
runs through the neighborhood the stream’s waters are actually
cleaned and the sediments accumulate pollutants. Indeed, the
stretches of water that runs through these neighborhoods act as water
processing plants for the metropolis.
This project has studied the different organic-load polluting
contributions to the water in a certain stretch of the canal, the
reduction of that load over the course of the canal, and the
incorporation of pollutants into the sediments. We have found that
the surface water has considerable ability to self-purify, mostly due to
processes of sedimentation and adsorption. The polluting load is
accumulated in the sediments where that load stabilizes slowly by
means of anaerobic processes. In this study, we also investigated the
risks of sediment management and the use of the processes studied
here in controlled conditions as tools of environmental restoration.
Abstract: This study attempts to identify the factors influencing
on women empowerment of rural area in Sri Lanka through micro
finance services. Data were collected from one hundred (100) rural
women involving self-employment activities through a questionnaire
using direct personal interviews. Judgment and Convenience Random
sampling technique was used to select the sample size from three
Divisional Secretariat divisions of Kandawalai, Poonakari and
Karachchi in Kilinochchi District. The factor analysis was performed
on fourteen (14) variables for screening and reducing the variables to
identify the influencing factors on empowerment. Multiple regression
analysis was used to identify the relationship between the three
empowerment factors and the impact of micro finance on overall
empowerment of rural women. The result of this study summarized
the variables into three factors namely decision making, freedom to
mobility and family support and which are positively associated with
empowerment. In addition to this the value of adjusted R2 is 0.248
indicates that all the variables extracted can be explained 24.8% of
the variation in the women empowerment through microfinance.
Independent variables of these three factors have positive correlation
with women empowerment as well as significant values at 5 percent
level.
Abstract: The model tests were conducted in the laboratory
without and with Plastic recycled polymer in fly ash steep slopes
overlaying soft foundation soils like fly ash and powai soil in order to
check the stability of steep slope. In this experiment, fly ash is used
as a filling material and Plastic Recycled Polymers of diameter =
3mm and length = 4mm were made from waste plastic product (lower
grade plastic product). The properties of fly ash and Plastic recycled
polymers are determined. From the experiments, load and settlement
have measured. From these data, load –settlement curves have
reported. It has been observed from test results that load carrying
capacity of mixture fly ash with Plastic Recycled Polymers slope is
more than that of fly ash slope. The deformation of Plastic Recycled
Polymers slope is slightly more than that of fly ash slope. A Finite
Element Method (F.E.M.) was also evaluated using PLAXIS 3D
version. The failure pattern, deformations and factor of safety are
reported based on analytical programme. The results from
experimental data and analytical programme are compared and
reported.
Abstract: This study presented to reduce earthquake damage and
emergency rehabilitation of critical structures such as schools, hightech
factories, and hospitals due to strong ground motions associated
with climate changes. Regarding recent trend, a strong earthquake
causes serious damage to critical structures and then the critical
structure might be influenced by sequence aftershocks (or tsunami)
due to fault plane adjustments. Therefore, in order to improve seismic
performance of critical structures, retrofitted or strengthening study
of the structures under aftershocks sequence after emergency
rehabilitation of the structures subjected to strong earthquakes is
widely carried out. Consequently, this study used composite material
for emergency rehabilitation of the structure rather than concrete and
steel materials because of high strength and stiffness, lightweight,
rapid manufacturing, and dynamic performance. Also, this study was
to develop or improve the seismic performance or seismic retrofit of
critical structures subjected to strong ground motions and earthquake
aftershocks, by utilizing GFRP-Corrugated Infill Panels (GCIP).
Abstract: ABC classification is widely used by managers for
inventory control. The classical ABC classification is based on Pareto
principle and according to the criterion of the annual use value only.
Single criterion classification is often insufficient for a closely
inventory control. Multi-criteria inventory classification models have
been proposed by researchers in order to consider other important
criteria. From these models, we will consider a specific model in
order to make a sensitive analysis on the composite score calculated
for each item. In fact, this score, based on a normalized average
between a good and a bad optimized index, can affect the ABC-item
classification. We will focus on items differently assigned to classes
and then propose a classification compromise.
Abstract: Moringa oleifera is a nutritious vegetable tree with
varieties of potential uses, as almost every part of the Moringa
oleifera tree can be used for food. This study was conducted in Oyo
State, Nigeria, to find out the level of acceptability of Moringa
oleifera diversified products among rural and urban dwellers.
Purposive sampling was used to select two local governments’ areas.
Stratified sampling technique was also used to select one community
each from rural and urban areas while snowball sampling technique
was used to select ten respondents each from the two communities,
making a total number of forty respondents. Data were analyzed
using frequencies, percentages, Chi-square, Pearson Product Moment
Correlation and regression analysis. Result from the study revealed
that majority of the respondents (80%) fell within the age range of
20-49 years and 55% of them were male, 55% were married, 70% of
them were Christians, 80% of them had tertiary education. The result
also showed that 85% were aware of the Moringa plant and (65%) of
them have consumed Moringa oleifera and the perception statements
on the benefits of Moringa oleifera indicated that (52.5%) of the
respondents rated Moringa oleifera to be favorable, most of them had
high acceptability for Moringa egusi soup, Moringa tea, Moringa pap
and yam pottage with Moringa. The result of the hypotheses testing
showed that there is a significant relationship between sex of the
respondents and acceptability of the diversified Moringa oleifera
products (x2=6.465, p = 0.011). There is also a significant
relationship between family size of the respondents level of
acceptability of the Moringa oleifera products (r = 0.327, p = 0.040).
Based on the level of acceptability of Moringa oleifera diversified
products; the plant is of great economic importance to the populace.
Therefore, there should be more public awareness through the media
to enlighten people on the beneficial effects of Moringa oleifera.