Abstract: The research presented in this paper has been focused
on analysing the impact of traffic on the sustainable development of
tourism in Croatia's Dubrovacko-Neretvanska County by the year
2020, based on the figures and trends reported in 2014 and using the
relevant variables that characterise the synergy of traffic and tourism
in, speaking from the geographic viewpoint, the most problematic
county in the Republic of Croatia. The basic hypothesis has been
confirmed through scientifically obtained research results, through
the quantification of the model's variables and the direct growth rates
of the designed model. On the basis of scientific insights into the
sustainable development of traffic and tourism in Dubrovacko-
Neretvanska County, it is possible to propose a new information
model for traffic at the service of the sustainable development of
tourism in the County for the period 2014-2020.
Abstract: Vegetation affects the mean and turbulent flow
structure. It may increase flood risks and sediment transport.
Therefore, it is important to develop analytical approaches for the bed
shear stress on vegetated bed, to predict resistance caused by
vegetation. In the recent years, experimental and numerical models
have both been developed to model the effects of submerged
vegetation on open-channel flow. In this paper, different analytic
models are compared and tested using the criteria of deviation, to
explore their capacity for predicting the mean velocity and select the
suitable one that will be applied in real case of rivers. The
comparison between the measured data in vegetated flume and
simulated mean velocities indicated, a good performance, in the case
of rigid vegetation, whereas, Huthoff model shows the best
agreement with a high coefficient of determination (R2=80%) and the
smallest error in the prediction of the average velocities.
Abstract: A Motzkin shift is a mathematical model for constraints
on genetic sequences. In terms of the theory of symbolic dynamics,
the Motzkin shift is nonsofic, and therefore, we cannot use the Perron-
Frobenius theory to calculate its topological entropy. The Motzkin
shift M(M,N) which comes from language theory, is defined to be the
shift system over an alphabet A that consists of N negative symbols,
N positive symbols and M neutral symbols. For an x in the full shift,
x will be in the Motzkin subshift M(M,N) if and only if every finite
block appearing in x has a non-zero reduced form. Therefore, the
constraint for x cannot be bounded in length. K. Inoue has shown that
the entropy of the Motzkin shift M(M,N) is log(M + N + 1). In this
paper, a new direct method of calculating the topological entropy of
the Motzkin shift is given without any measure theoretical discussion.
Abstract: This research study aimed to survey and analyze the
attitudes of pre-service teachers’ the analytical thinking development
based on Miller’s Model. The informants of this study were 22 third
year teacher students majoring in Thai. The course where the
instruction was conducted was English for Academic Purposes in
Thai Language 2. The instrument of this research was an open-ended
questionnaire with two dimensions of questions: academic and
satisfaction dimensions. The investigation revealed the positive
attitudes. In the academic dimension, the majority of 12 (54.54%),
the highest percentage, reflected that the method of teaching
analytical thinking and language simultaneously was their new
knowledge and the similar percentage also belonged to text cohesion
in writing. For the satisfaction, the highest frequency count was from
17 of them (77.27%) and this majority favored the openness or
friendliness of the teacher.
Abstract: VACTERL association is a rare disorder with various
congenital malformations. The aetiology remains unknown.
Combination of at least three congenital anomalies of the following
criteria is required for diagnosis: vertebral defects, anal atresia,
cardiac anomalies, tracheo-esophageal fistula, renal anomalies, and
limb defects. The first case was 1-day old male neonate with multiple
congenital anomalies was bore from 28 years old mother. The mother
had history of pregnancy with lymphocyte therapy. His anomalies
included: defects in thoracic and lumbar vertebral, anal atresia,
bilateral hydronephrosis, atrial septal defect, and lower limb
abnormality. Other anomalies were cryptorchidism and nasal canal
narrowing. The second case was born with 32 weeks gestational age
from mother with history of pregnancy with lymphocyte therapy. He
had thoracic vertebral defect, cardiac anomalies and renal defect.
diagnosis based on clinical finding is VACTERL association. Early
diagnosis is very important to investigation and treatment of other
coexistence anomalies. VACTERL association in mothers with
history of pregnancy with lymphocyte therapy has suggested possibly
of relationship between VACTERL association and this method of
pregnancy.
Abstract: In the present work, the alloy of Bismuth-lead is
prepared on the basis of percentage of molecular weight 9:1, 5:5 and
1:9 ratios and grown by Zone- Refining Technique under a vacuum
atmosphere. The EDAX of these samples are done and the results are
reported. Micro hardness test has been used as an alternative test for
measuring material’s tensile properties. The effect of temperature and
load on the hardness of the grown alloy has been studied. Further the
comparative studies of work hardening coefficients are reported.
Abstract: Construction cost estimation is one of the most
important aspects of construction project design. For generations, the
process of cost estimating has been manual, time-consuming and
error-prone. This has partly led to most cost estimates to be unclear
and riddled with inaccuracies that at times lead to over- or underestimation
of construction cost. The development of standard set of
measurement rules that are understandable by all those involved in a
construction project, have not totally solved the challenges. Emerging
Building Information Modelling (BIM) technologies can exploit
standard measurement methods to automate cost estimation process
and improve accuracies. This requires standard measurement
methods to be structured in ontological and machine readable format;
so that BIM software packages can easily read them. Most standard
measurement methods are still text-based in textbooks and require
manual editing into tables or Spreadsheet during cost estimation. The
aim of this study is to explore the development of an ontology based
on New Rules of Measurement (NRM) commonly used in the UK for
cost estimation. The methodology adopted is Methontology, one of
the most widely used ontology engineering methodologies. The
challenges in this exploratory study are also reported and
recommendations for future studies proposed.
Abstract: The increasing demand of gallium, indium and
rare-earth elements for the production of electronics, e.g. solid
state-lighting, photovoltaics, integrated circuits, and liquid crystal
displays, will exceed the world-wide supply according to current
forecasts. Recycling systems to reclaim these materials are not yet in
place, which challenges the sustainability of these technologies. This
paper proposes a multispectral imaging system as a basis for a vision
based recognition system for valuable components of electronics
waste. Multispectral images intend to enhance the contrast of images
of printed circuit boards (single components, as well as labels) for
further analysis, such as optical character recognition and entire
printed circuit board recognition. The results show, that a higher
contrast is achieved in the near infrared compared to ultraviolett and
visible light.
Abstract: The rapid development of culture tourism has drawn
attention to conserving cultural values especially by developing
countries that would like to benefit from the economic contribution
this type of tourism attracts. Tourism can have both positive and
negative outcomes for historical settlements and their residents. The
accommodation-purposed rehabilitation and revitalization project in
“Sigacik Old City Zone” are to be discussed with spatial, economic,
social and organizational dimensions. It is aimed to evaluate the
relationship between the development of tourism and sustainable
heritage conservation.
Abstract: In this paper, a new trend for improvement in semianalytical
method based on scale boundaries in order to solve the 2D
elastodynamic problems is provided. In this regard, only the
boundaries of the problem domain discretization are by specific subparametric
elements. Mapping functions are uses as a class of higherorder
Lagrange polynomials, special shape functions, Gauss-Lobatto-
Legendre numerical integration, and the integral form of the weighted
residual method, the matrix is diagonal coefficients in the equations
of elastodynamic issues. Differences between study conducted and
prior research in this paper is in geometry production procedure of
the interpolation function and integration of the different is selected.
Validity and accuracy of the present method are fully demonstrated
through two benchmark problems which are successfully modeled
using a few numbers of DOFs. The numerical results agree very well
with the analytical solutions and the results from other numerical
methods.
Abstract: Clustering involves the partitioning of n objects into k
clusters. Many clustering algorithms use hard-partitioning techniques
where each object is assigned to one cluster. In this paper we propose
an overlapping algorithm MCOKE which allows objects to belong to
one or more clusters. The algorithm is different from fuzzy clustering
techniques because objects that overlap are assigned a membership
value of 1 (one) as opposed to a fuzzy membership degree. The
algorithm is also different from other overlapping algorithms that
require a similarity threshold be defined a priori which can be
difficult to determine by novice users.
Abstract: The California Bearing Ratio (CBR) has been
acknowledged as an important parameter to characterize the bearing
capacity of earth structures, such as earth dams, road embankments,
airport runways, bridge abutments and pavements. Technically, the
CBR test can be carried out in the laboratory or in the field. The CBR
test is time-consuming and is infrequently performed due to the
equipment needed and the fact that the field moisture content keeps
changing over time. Over the years, many correlations have been
developed for the prediction of CBR by various researchers,
including the dynamic cone penetrometer, undrained shear strength
and Clegg impact hammer. This paper reports and discusses some of
the results from a study on the prediction of CBR. In the current
study, the CBR test was performed in the laboratory on some finegrained
subgrade soils collected from various locations in Victoria.
Based on the test results, a satisfactory empirical correlation was
found between the CBR and the physical properties of the
experimental soils.
Abstract: Water contamination by toxic compound is one of the serious environmental problems today. These toxic compounds mostly originated from industrial effluents, agriculture, natural sources and human waste. These studies focus on modification of multiwalled carbon nanotube (MWCNTs) with nanoparticle of calixarene and explore the possibility of using this modification for the remediation of cadmium in water. The nanocomposites were prepared by dissolving calixarene in chloroform solution as solvent, followed by additional multiwalled carbon nanotube (MWCNTs) then sonication process for 3 hour and fabricated the nanocomposites on substrate by spin coating method. Finally, the nanocomposites were tested on cadmium ion (10 mg/ml). The morphology of nanocomposites was investigated by FESEM showing the formation of calixarene on the outer walls of carbon nanotube and cadmium ion also clearly seen from the micrograph. This formation was supported by using energy dispersive x-ray (EDX). The presence of cadmium ions in the films, leads to some changes in the surface potential and Fourier Transform Infrared spectroscopy (FTIR).The nanocomposites MWCNTs-calixarene have potential for development of sensor for pollutant monitoring and nanoelectronics devices applications.
Abstract: This paper presents the details of a numerical study of
buckling and post buckling behaviour of laminated carbon fiber
reinforced plastic (CFRP) thin-walled cylindrical shell under axial
compression using asymmetric meshing technique (AMT) by
ABAQUS. AMT is considered to be a new perturbation method to
introduce disturbance without changing geometry, boundary
conditions or loading conditions. Asymmetric meshing affects both
predicted buckling load and buckling mode shapes. Cylindrical shell
having lay-up orientation [0^o/+45^o/-45^o/0^o] with radius to thickness
ratio (R/t) equal to 265 and length to radius ratio (L/R) equal to 1.5 is
analysed numerically. A series of numerical simulations
(experiments) are carried out with symmetric and asymmetric
meshing to study the effect of asymmetric meshing on predicted
buckling behaviour. Asymmetric meshing technique is employed in
both axial direction and circumferential direction separately using
two different methods, first by changing the shell element size and
varying the total number elements, and second by varying the shell
element size and keeping total number of elements constant. The
results of linear analysis (Eigenvalue analysis) and non-linear
analysis (Riks analysis) using symmetric meshing agree well with
analytical results. The results of numerical analysis are presented in
form of non-dimensional load factor, which is the ratio of buckling
load using asymmetric meshing technique to buckling load using
symmetric meshing technique. Using AMT, load factor has about 2%
variation for linear eigenvalue analysis and about 2% variation for
non-linear Riks analysis. The behaviour of load end-shortening curve
for pre-buckling is same for both symmetric and asymmetric meshing
but for asymmetric meshing curve behaviour in post-buckling
becomes extraordinarily complex. The major conclusions are:
different methods of AMT have small influence on predicted
buckling load and significant influence on load displacement curve
behaviour in post buckling; AMT in axial direction and AMT in
circumferential direction have different influence on buckling load
and load displacement curve in post-buckling.
Abstract: The present work aims to throw light on the effects of
arcing in air on the surface state of contact pastilles made of silvernickel
Ag-Ni (60/40). Also, the photoelectric emission from these
electrical contacts has been investigated in the spectral range of 196-
256 nm. In order to study the effects of arcing on the EWF, the
metallic samples were subjected to electrical arcs in air, at
atmospheric pressure and room temperature, after that, they have
been introduced into the vacuum chamber of an experimental UHV
set-up for EWF measurements. Both Fowler method of isothermal
curves and linearized Fowler plots were used for the measurement of
the EWF by the photoelectric effect.
It has been found that the EWF varies with the number of applied
arcs. Thus, after 500 arcs in air, the observed EWF increasing is
probably due to progressive inclusion of oxide on alloy surface.
Microscopic examination is necessary to get better understandings on
EWF of silver alloys, for both virgin and arced electrical contacts.
Abstract: Image search engines rely on the surrounding textual
keywords for the retrieval of images. It is a tedious work for the
search engines like Google and Bing to interpret the user’s search
intention and to provide the desired results. The recent researches
also state that the Google image search engines do not work well on
all the images. Consequently, this leads to the emergence of efficient
image retrieval technique, which interprets the user’s search intention
and shows the desired results. In order to accomplish this task, an
efficient image re-ranking framework is required. Sequentially, to
provide best image retrieval, the new image re-ranking framework is
experimented in this paper. The implemented new image re-ranking
framework provides best image retrieval from the image dataset by
making use of re-ranking of retrieved images that is based on the
user’s desired images. This is experimented in two sections. One is
offline section and other is online section. In offline section, the reranking
framework studies differently (reference classes or Semantic
Spaces) for diverse user query keywords. The semantic signatures get
generated by combining the textual and visual features of the images.
In the online section, images are re-ranked by comparing the
semantic signatures that are obtained from the reference classes with
the user specified image query keywords. This re-ranking
methodology will increases the retrieval image efficiency and the
result will be effective to the user.
Abstract: This study is used as a definition method to the value
and function in manufacturing sector. In concurrence of discussion
about present condition of modeling method, until now definition of
1D-CAE is ambiguity and not conceptual. Across all the physic fields,
those methods are defined with the formulation of differential
algebraic equation which only applied time derivation and simulation.
At the same time, we propose semi-acausal modeling concept and
differential algebraic equation method as a newly modeling method
which the efficiency has been verified through the comparison of
numerical analysis result between the semi-acausal modeling
calculation and FEM theory calculation.
Abstract: The study of organisations’ information security
cultures has attracted scholars as well as healthcare services industry
to research the topic and find appropriate tools and approaches to
develop a positive culture. The vast majority of studies in Saudi
national health services are on the use of technology to protect and
secure health services information. On the other hand, there is a lack
of research on the role and impact of an organisation’s cultural
dimensions on information security. This research investigated and
analysed the role and impact of cultural dimensions on information
security in Saudi Arabia health service. Hypotheses were tested and
two surveys were carried out in order to collect data and information
from three major hospitals in Saudi Arabia (SA). The first survey
identified the main cultural-dimension problems in SA health
services and developed an initial information security culture
framework model. The second survey evaluated and tested the
developed framework model to test its usefulness, reliability and
applicability. The model is based on human behaviour theory, where
the individual’s attitude is the key element of the individual’s
intention to behave as well as of his or her actual behaviour. The
research identified a set of cultural and sub-cultural dimensions in SA
health information security and services.
Abstract: In this report we have discussed the theoretical aspects
of the flow transformation, occurring through a series of bifurcations.
The parameters and their continuous diversion, the intermittent bursts
in the transition zone, variation of velocity and pressure with time,
effect of roughness in turbulent zone, and changes in friction factor
and head loss coefficient as a function of Reynolds number for a
transverse flow across a cylinder have been discussed. An analysis of
the variation in the wake length with Reynolds number was done in
FORTRAN.
Abstract: High Peak to Average Power Ratio (PAPR) of the
transmitted signal is a serious problem in multicarrier systems (MC),
such as Orthogonal Frequency Division Multiplexing (OFDM), or in
Multi-Carrier Code Division Multiple Access (MC-CDMA) systems,
due to large number of subcarriers. This effect is possible reduce with
some PAPR reduction techniques. Spreading sequences at the
presence of Saleh and Rapp models of high power amplifier (HPA)
have big influence on the behavior of system. In this paper we
investigate the bit-error-rate (BER) performance of MC-CDMA
systems. Basically we can see from simulations that the MC-CDMA
system with Iterative algorithm can be providing significantly better
results than the MC-CDMA system. The results of our analyses are
verified via simulation.