Abstract: This study adopted previous fault patterns, results of
detection analysis, historical records and data, and experts-
experiences to establish fuzzy principles and estimate the failure
probability index of components of a power transformer. Considering
that actual parameters and limiting conditions of parameters may
differ, this study used the standard data of IEC, IEEE, and CIGRE as
condition parameters. According to the characteristics of each
condition parameter, relative degradation was introduced to reflect the
degree of influence of the factors on the transformer condition. The
method of fuzzy mathematics was adopted to determine the
subordinate function of the transformer condition. The calculation
used the Matlab Fuzzy Tool Box to select the condition parameters of
coil winding, iron core, bushing, OLTC, insulating oil and other
auxiliary components and factors (e.g., load records, performance
history, and maintenance records) of the transformer to establish the
fuzzy principles. Examples were presented to support the rationality
and effectiveness of the evaluation method of power transformer
performance conditions, as based on fuzzy comprehensive evaluation.
Abstract: In this paper an alternative visualisation approach of
the wake behind different vehicle body shapes with simplified and
fully-detailed underbody has been proposed and analysed. This
allows for a more clear distinction among the different wake regions.
This visualisation is based on a transformation of the cartesian
coordinates of a chosen wake plane to polar coordinates, using as
filter velocities lower than the freestream. This transformation
produces a polar wake plot that enables the division and
quantification of the wake in a number of sections. In this paper,
local drag has been used to visualise the drag contribution of the flow
by the different sections. Visually, a balanced wake can be observed
by the concentric behaviour of the polar plots. Alternatively,
integration of the local drag of each degree section as a ratio of the
total local drag yields a quantifiable approach of the wake uniformity,
where different sections contribute equally to the local drag, with the
exception of the wheels.
Abstract: This paper presents a simple and sensitive kinetic
spectrophotometric method for the determination of ramipril in
commercial dosage forms. The method is based on the reaction of the
drug with 1-chloro-2,4-dinitrobenzene (CDNB) in dimethylsulfoxide
(DMSO) at 100 ± 1ºC. The reaction is followed
spectrophotometrically by measuring the rate of change of the
absorbance at 420 nm. Fixed-time (ΔA) and equilibrium methods are
adopted for constructing the calibration curves. Both the calibration
curves were found to be linear over the concentration ranges 20 - 220
μg/ml. The regression analysis of calibration data yielded the linear
equations: Δ A = 6.30 × 10-4 + 1.54 × 10-3 C and A = 3.62 × 10-4 +
6.35 × 10-3 C for fixed time (Δ A) and equilibrium methods,
respectively. The limits of detection (LOD) for fixed time and
equilibrium methods are 1.47 and 1.05 μg/ml, respectively. The
method has been successfully applied to the determination of ramipril
in commercial dosage forms. Statistical comparison of the results
shows that there is no significant difference between the proposed
methods and Abdellatef-s spectrophotometric method.
Abstract: Environmental aspects plays a central role in environmental management system (EMS) because it is the basis for the identification of an organization-s environmental targets. The
existing methods for the assessment of environmental aspects are grouped into three categories: risk assessment-based (RA-based),
LCA-based and criterion-based methods. To combine the benefits of
these three categories of research, this study proposes an integrated framework, combining RA-, LCA- and criterion-based methods. The
integrated framework incorporates LCA techniques for the identification of the causal linkage for aspect, pathway, receptor and
impact, uses fuzzy logic to assess aspects, considers fuzzy conditions,
in likelihood assessment, and employs a new multi-criteria decision analysis method - multi-criteria and multi-connection comprehensive
assessment (MMCA) - to estimate significant aspects in EMS. The proposed model is verified, using a real case study and the results show
that this method successfully prioritizes the environmental aspects.
Abstract: In this paper we present a general formalism for the
establishment of the family of selective regressor affine projection
algorithms (SR-APA). The SR-APA, the SR regularized APA (SR-RAPA),
the SR partial rank algorithm (SR-PRA), the SR binormalized
data reusing least mean squares (SR-BNDR-LMS), and the SR normalized
LMS with orthogonal correction factors (SR-NLMS-OCF)
algorithms are established by this general formalism. We demonstrate
the performance of the presented algorithms through simulations in
acoustic echo cancellation scenario.
Abstract: In real-time networks a large number of application programs are relying on video data and heterogeneous data transmission techniques. The aim of this research is presenting a method for end-to-end vouch quality service in surface applicationlayer for sending video data in comparison form in wireless heterogeneous networks. This method tries to improve the video sending over the wireless heterogeneous networks with used techniques in surface layer, link and application. The offered method is showing a considerable improvement in quality observing by user. In addition to this, other specifications such as shortage of data load that had require to resending and limited the relation period length to require time for second data sending, help to be used the offered method in the wireless devices that have a limited energy. The presented method and the achieved improvement is simulated and presented in the NS-2 software.
Abstract: This paper reviews designs of the built environment
from a sustainability perspective, emphasizing their importance in
achieving ecological and sustainable economic objectives. The built
environment has traditionally resulted in loss of biodiversity,
extinction of some species, climate change, excessive water use, land
degradation, space depletion, waste accumulation, energy
consumption and environmental pollution. Materials used like
plastics, metals, bricks, concrete, cement, natural aggregates, glass
and plaster have wreaked havoc on the earth´s resources, since they
have high levels of embodied energy hence not sustainable.
Additional resources are consumed during use and disposal phases.
Proposed designs for sustainability solutions include: ecological
sanitation and eco-efficiency systems that ensure social, economic,
environmental and technical sustainability. Renewable materials and
energy systems, passive cooling and heating systems and material
and energy reduction, reuse and recycling can improve the sector.
These ideas are intended to inform the field of ecological design of
the built environment.
Abstract: This paper proposes a new approach to offer a private
cloud service in HPC clusters. In particular, our approach relies on
automatically scheduling users- customized environment request as a
normal job in batch system. After finishing virtualization request jobs,
those guest operating systems will dismiss so that compute nodes will
be released again for computing. We present initial work on the
innovative integration of HPC batch system and virtualization tools
that aims at coexistence such that they suffice for meeting the
minimizing interference required by a traditional HPC cluster. Given
the design of initial infrastructure, the proposed effort has the potential
to positively impact on synergy model. The results from the
experiment concluded that goal for provisioning customized cluster
environment indeed can be fulfilled by using virtual machines, and
efficiency can be improved with proper setup and arrangements.
Abstract: Multi-site damage (MSD) has been a challenge to
aircraft, civil and power plant structures. In real life components are subjected to cracking at many vulnerable locations such as the bolt
holes. However, we do not consider for the presence of multiple cracks. Unlike components with a single crack, these components are
difficult to predict. When two cracks approach one another, their
stress fields influence each other and produce enhancing or shielding effect depending on the position of the cracks. In the present study,
numerical studies on fracture analysis have been conducted by using
the developed code based on the modified virtual crack closure integral (MVCCI) technique and finite element analysis (FEA) software ABAQUS for computing SIF of plates with multiple cracks.
Various parametric studies have been carried out and the results have
been compared with literature where ever available and also with the solution, obtained by using ABAQUS. By conducting extensive
numerical studies expressions for SIF have been obtained for collinear cracks and non-aligned cracks.
Abstract: In this paper, we study the existence of solution of
the four-point boundary value problem for second-order differential
equations with impulses by using leray-Schauder theory:
Abstract: Quality of 2D and 3D cross-sectional images produce
by Computed Tomography primarily depend upon the degree of
precision of primary and secondary X-Ray intensity detection.
Traditional method of primary intensity detection is apt to errors.
Recently the X-Ray intensity measurement system along with smart
X-Ray sensors is developed by our group which is able to detect
primary X-Ray intensity unerringly. In this study a new smart X-Ray
sensor is developed using Light-to-Frequency converter TSL230
from Texas Instruments which has numerous advantages in terms of
noiseless data acquisition and transmission. TSL230 construction is
based on a silicon photodiode which converts incoming X-Ray
radiation into the proportional current signal. A current to frequency
converter is attached to this photodiode on a single monolithic CMOS
integrated circuit which provides proportional frequency count to
incoming current signal in the form of the pulse train. The frequency
count is delivered to the center of PICDEM FS USB board with
PIC18F4550 microcontroller mounted on it. With highly compact
electronic hardware, this Demo Board efficiently read the smart
sensor output data. The frequency output approaches overcome
nonlinear behavior of sensors with analog output thus un-attenuated
X-Ray intensities could be measured precisely and better
normalization could be acquired in order to attain high resolution.
Abstract: Concrete performance is strongly affected by the
particle packing degree since it determines the distribution of the
cementitious component and the interaction of mineral particles. By
using packing theory designers will be able to select optimal
aggregate materials for preparing concrete with low cement content,
which is beneficial from the point of cost. Optimum particle packing
implies minimizing porosity and thereby reducing the amount of
cement paste needed to fill the voids between the aggregate particles,
taking also the rheology of the concrete into consideration. For
reaching good fluidity superplasticizers are required. The results from
pilot tests at Luleå University of Technology (LTU) show various
forms of the proposed theoretical models, and the empirical approach
taken in the study seems to provide a safer basis for developing new,
improved packing models.
Abstract: The primary cause of Total Hip Replacement (THR)
failure for younger patients is aseptic loosening. This complication is
twice more likely to happen in acetabular cup than in femoral stem.
Excessive micromotion between bone and implant will cause
loosening and it depends in patient activities, age and bone. In this
project, the effects of different metal back design of press fit on
osseointegration of the acetabular cup are carried out. Commercial
acetabular cup designs, namely Spiked, Superfix and Quadrafix are
modelled and analyzed using commercial finite element software.
The diameter of acetabular cup is based on the diameter of acetabular
rim to make sure the component fit to the acetabular cavity. A new
design of acetabular cup are proposed and analyzed to get better
osseointegration between the bones and implant interface. Results
shows that the proposed acetabular cup designs are more stable
compared to other designs with respect to stress and displacement
aspects.
Abstract: The purpose of this study was to explore the complex
flow structure a novel active-type micromixer that based on concept of
Wankle-type rotor. The characteristics of this micromixer are two
folds; a rapid mixing of reagents in a limited space due to the
generation of multiple vortices and a graduate increment in dynamic
pressure as the mixed reagents is delivered to the output ports.
Present micro-mixer is consisted of a rotor with shape of triangle
column, a blending chamber and several inlet and outlet ports. The
geometry of blending chamber is designed to make the rotor can be
freely internal rotated with a constant eccentricity ratio. When the
shape of the blending chamber and the rotor are fixed, the effects of
rotating speed of rotor and the relative locations of ports on the mixing
efficiency are numerical studied. The governing equations are
unsteady, two-dimensional incompressible Navier-Stokes equation
and the working fluid is the water. The species concentration equation
is also solved to reveal the mass transfer process of reagents in various
regions then to evaluate the mixing efficiency.
The dynamic mesh technique was implemented to model the
dynamic volume shrinkage and expansion of three individual
sub-regions of blending chamber when the rotor conducted a complete
rotating cycle. Six types of ports configuration on the mixing
efficiency are considered in a range of Reynolds number from 10 to
300. The rapid mixing process was accomplished with the multiple
vortex structures within a tiny space due to the equilibrium of shear
force, viscous force and inertial force. Results showed that the highest
mixing efficiency could be attained in the following conditions: two
inlet and two outlet ports configuration, that is an included angle of 60
degrees between two inlets and an included angle of 120 degrees
between inlet and outlet ports when Re=10.
Abstract: An efficient architecture for low jitter All Digital
Phase Locked Loop (ADPLL) suitable for high speed SoC
applications is presented in this paper. The ADPLL is designed using
standard cells and described by Hardware Description Language
(HDL). The ADPLL implemented in a 90 nm CMOS process can
operate from 10 to 200 MHz and achieve worst case frequency
acquisition in 14 reference clock cycles. The simulation result shows
that PLL has cycle to cycle jitter of 164 ps and period jitter of 100 ps
at 100MHz. Since the digitally controlled oscillator (DCO) can
achieve both high resolution and wide frequency range, it can meet
the demands of system-level integration. The proposed ADPLL can
easily be ported to different processes in a short time. Thus, it can
reduce the design time and design complexity of the ADPLL, making
it very suitable for System-on-Chip (SoC) applications.
Abstract: A free-trade agreement is found to increase Thailand-s
agricultural imports from New Zealand, despite the short span of
time for which the agreement has been operational. The finding is
described by autoregressive estimates that correct for possible unit
roots in the data. The agreement-s effect upon imports is also
estimated while considering an error-correction model of imports
against gross domestic product.
Abstract: In this paper, we propose a Perceptually Optimized Embedded ZeroTree Image Coder (POEZIC) that introduces a perceptual weighting to wavelet transform coefficients prior to control SPIHT encoding algorithm in order to reach a targeted bit rate with a perceptual quality improvement with respect to the coding quality obtained using the SPIHT algorithm only. The paper also, introduces a new objective quality metric based on a Psychovisual model that integrates the properties of the HVS that plays an important role in our POEZIC quality assessment. Our POEZIC coder is based on a vision model that incorporates various masking effects of human visual system HVS perception. Thus, our coder weights the wavelet coefficients based on that model and attempts to increase the perceptual quality for a given bit rate and observation distance. The perceptual weights for all wavelet subbands are computed based on 1) luminance masking and Contrast masking, 2) the contrast sensitivity function CSF to achieve the perceptual decomposition weighting, 3) the Wavelet Error Sensitivity WES used to reduce the perceptual quantization errors. The new perceptually optimized codec has the same complexity as the original SPIHT techniques. However, the experiments results show that our coder demonstrates very good performance in terms of quality measurement.
Abstract: The mechanical quadrature methods for solving the boundary integral equations of the anisotropic Darcy-s equations with Dirichlet conditions in smooth domains are presented. By applying the collectively compact theory, we prove the convergence and stability of approximate solutions. The asymptotic expansions for the error show that the methods converge with the order O (h3), where h is the mesh size. Based on these analysis, extrapolation methods can be introduced to achieve a higher convergence rate O (h5). An a posterior asymptotic error representation is derived in order to construct self-adaptive algorithms. Finally, the numerical experiments show the efficiency of our methods.
Abstract: This paper presents a hybrid fuzzy-PD plus PID
(HFPP) controller and its application to steam distillation process for
essential oil extraction system. Steam temperature is one of the most
significant parameters that can influence the composition of essential
oil yield. Due to parameter variations and changes in operation
conditions during distillation, a robust steam temperature controller becomes nontrivial to avoid the degradation of essential oil quality.
Initially, the PRBS input is triggered to the system and output of steam temperature is modeled using ARX model structure. The
parameter estimation and tuning method is adopted by simulation
using HFPP controller scheme. The effectiveness and robustness of
proposed controller technique is validated by real time
implementation to the system. The performance of HFPP using 25 and 49 fuzzy rules is compared. The experimental result demonstrates the proposed HFPP using 49 fuzzy rules achieves a
better, consistent and robust controller compared to PID when considering the test on tracking the set point and the effects due to disturbance.