Abstract: In present global scenario, aluminum alloys are
coining the attention of many innovators as competing structural
materials for automotive and space applications. Comparing to other
challenging alloys, especially, 7xxx series aluminum alloys have
been studied seriously because of benefits such as moderate strength;
better deforming characteristics and affordable cost. It is expected
that substitution of aluminum alloys for steels will result in great
improvements in energy economy, durability and recyclability.
However, it is necessary to improve the strength and the formability
levels at low temperatures in aluminum alloys for still better
applications. Aluminum–Zinc–Magnesium with or without other
wetting agent denoted as 7XXX series alloys are medium strength
heat treatable alloys. In addition to Zn, Mg as major alloying
additions, Cu, Mn and Si are the other solute elements which
contribute for the improvement in mechanical properties by suitable
heat treatment process. Subjecting to suitable treatments like age
hardening or cold deformation assisted heat treatments; known as low
temperature thermomechanical treatments (LTMT) the challenging
properties might be incorporated. T6 is the age hardening or
precipitation hardening process with artificial aging cycle whereas T8
comprises of LTMT treatment aged artificially with X% cold
deformation. When the cold deformation is provided after solution
treatment, there is increase in hardness related properties such as
wear resistance, yield and ultimate strength, toughness with the
expense of ductility. During precipitation hardening both hardness
and strength of the samples are increasing. The hardness value may
further improve when room temperature deformation is positively
supported with age hardening known as thermomechanical treatment.
It is intended to perform heat treatment and evaluate hardness, tensile
strength, wear resistance and distribution pattern of reinforcement in
the matrix. 2 to 2.5 and 3 to 3.5 times increase in hardness is reported
in age hardening and LTMT treatments respectively as compared to
as-cast composite. There was better distribution of reinforcements in
the matrix, nearly two fold increase in strength levels and up to 5
times increase in wear resistance are also observed in the present
study.
Abstract: In Electric Power Steering (EPS), spoke type
Brushless AC (BLAC) motors offer distinct advantages over other
electric motor types in terms torque smoothness, reliability and
efficiency. This paper deals with the shape optimization of spoke
type BLAC motor, in order to reduce cogging torque. This paper
examines 3 steps skewing rotor angle, optimizing rotor core edge and
rotor overlap length for reducing cogging torque in spoke type BLAC
motor. The methods were applied to existing machine designs and
their performance was calculated using finite- element analysis
(FEA). Prototypes of the machine designs were constructed and
experimental results obtained. It is shown that the FEA predicted the
cogging torque to be nearly reduce using those methods.
Abstract: Cyber exercises used to assess the preparedness of a
community against cyber crises, technology failures and Critical
Information Infrastructure (CII) incidents. The cyber exercises also
called cyber crisis exercise or cyber drill, involved partnerships or
collaboration of public and private agencies from several sectors.
This study investigates Organisation Cyber Resilience (OCR) of
participation sectors in cyber exercise called X Maya in Malaysia.
This study used a principal based cyber resilience survey called CSuite
Executive checklist developed by World Economic Forum in
2012. To ensure suitability of the survey to investigate the OCR, the
reliability test was conducted on C-Suite Executive checklist items.
The research further investigates the differences of OCR in ten
Critical National Infrastructure Information (CNII) sectors
participated in the cyber exercise. The One Way ANOVA test result
showed a statistically significant difference of OCR among ten CNII
sectors participated in the cyber exercise.
Abstract: Despite the advances made in various new
technologies, application of these technologies for agriculture still
remains a formidable task, as it involves integration of diverse
domains for monitoring the different process involved in agricultural
management. Advances in ambient intelligence technology represents
one of the most powerful technology for increasing the yield of
agricultural crops and to mitigate the impact of water scarcity,
climatic change and methods for managing pests, weeds and diseases.
This paper proposes a GPS-assisted, machine to machine solutions
that combine information collected by multiple sensors for the
automated management of paddy crops. To maintain the economic
viability of paddy cultivation, the various techniques used in
agriculture are discussed and a novel system which uses ambient
intelligence technique is proposed in this paper. The ambient
intelligence based agricultural system gives a great scope.
Abstract: This paper investigates the connotation, and some of
the realistic implications, of the economic reform of health sector in
under developed countries. The paper investigates the issues that
economic reforms have to address, and the policy targets they are
considered to accomplish. The work argues that the development of
economic reform is not connected only with understanding the
priorities and refining them, furthermore with reformation and
restructuring the organizations through which health policies are
employed. Considering various organizational values, that are likely
to be regular to all economic reform programs, a regulatory approach
to institutional reform is unsuitable. The paper further investigates the
selection of economic reform that may as well influence via technical
suggestions and analysis, but the verdict to continue, and the
consequent success of execution, eventually depends on the
progressive political sustainability. The paper concludes by giving
examples of institutional reforms from various underdeveloped
countries and includes recommendation of the responsibility and
control of donor organizations.
Abstract: In recent research copper and manganese systems
were found to be the most active in CO and organic compounds
oxidation among the base catalysts. The mixed copper manganese
oxide has been widely studied in oxidation reactions because of their
higher activity at low temperatures in comparison with single oxide
catalysts. The results showed that the formation of spinel
CuxMn3−xO4 in the oxidized catalyst is responsible for the activity
even at room temperature. That is why the most of the investigations
are focused on the hopcalite catalyst (CuMn2O4) as the best coppermanganese
catalyst. Now it’s known that this is true only for CO
oxidation, but not for mixture of CO and VOCs. The purpose of this
study is to investigate the alumina supported copper-manganese
catalysts with different Cu/Mn molar ratio in terms of oxidation of
CO, methanol and dimethyl ether. The catalysts were prepared by impregnation of γ-Al2O3 with
copper and manganese nitrates and the catalytic activity
measurements were carried out in two stage continuous flow
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions closest possible to the industrial. Gas
mixtures on the input and output of the reactor were analyzed with a
gas chromatograph, equipped with FID and TCD detectors. The
texture characteristics were determined by low-temperature (- 196oС)
nitrogen adsorption in a Quantachrome Instruments NOVA 1200e
(USA) specific surface area & pore analyzer. Thermal, XRD and
TPR analyses were performed. It was established that the active component of the mixed Cu-
Mn/γ–alumina catalysts strongly depends on the Cu/Mn molar ratio.
Highly active alumina supported Cu-Mn catalysts for CO, methanol
and DME oxidation were synthesized. While the hopcalite is the best
catalyst for CO oxidation, the best compromise for simultaneous
oxidation of all components is the catalyst with Cu/Mn molar ratio
1:5.
Abstract: In this paper air quality conditions in Makkah and
Leeds are compared. These two cities have totally different climatic
conditions. Makkah climate is characterised as hot and dry (arid)
whereas that of Leeds is characterised as cold and wet (temperate).
This study uses air quality data from 2012 collected in Makkah,
Saudi Arabia and Leeds, UK. The concentrations of all pollutants,
except NO are higher in Makkah. Most notable, the concentrations of
PM10 are much higher in Makkah than in Leeds. This is probably due
to the arid nature of climatic conditions in Makkah and not solely due
to anthropogenic emission sources, otherwise like PM10 some of the
other pollutants, such as CO, NO, and SO2 would have shown much
greater difference between Leeds and Makkah. Correlation analysis is
performed between different pollutants at the same site and the same
pollutants at different sites. In Leeds the correlation between PM10
and other pollutants is significantly stronger than in Makkah. Weaker
correlation in Makkah is probably due to the fact that in Makkah
most of the gaseous pollutants are emitted by combustion processes,
whereas most of the PM10 is generated by other sources, such as
windblown dust, re-suspension, and construction activities. This is in
contrast to Leeds where all pollutants including PM10 are
predominantly emitted by combustions, such as road traffic.
Furthermore, in Leeds frequent rains wash out most of the
atmospheric particulate matter and suppress re-suspension of dust.
Temporal trends of various pollutants are compared and discussed.
This study emphasises the role of climatic conditions in managing air
quality, and hence the need for region-specific controlling strategies
according to the local climatic and meteorological conditions.
Abstract: Present work deals with the possible use of fertigation
in agriculture and its impact on the availability of mineral nitrogen
(Nmin) in topsoil and subsoil horizons. The aim of the present study is
to demonstrate the effect of the organic matter presence in fertigation
on microbial transformation and availability of mineral nitrogen
forms. The main investigation reason is the potential use of pretreated
waste water, as a source of organic carbon (Corg) and residual
nutrients (Nmin) for fertigation. Laboratory experiment has been
conducted to demonstrate the effect of the arable land fertilization
method on the Nmin availability in different depths of the soil with
the usage of model experimental containers filled with soil from
topsoil and podsoil horizons that were taken from the precise area.
Tufted hairgrass (Deschampsia caespitosa) has been chosen as a
model plant. The water source protection zone Brezova nad Svitavou
has been a research area where significant underground reservoirs of
drinking water of the highest quality are located. From the second
half of the last century local sources of drinking water show
nitrogenous compounds increase that get here almost only from
arable lands. Therefore, an attention of the following text focuses on
the fate of mineral nitrogen in the complex plant-soil. Research
results show that the fertigation application with Corg in a
combination with mineral fertilizer can reduce the amount of Nmin
leached from topsoil horizon of agricultural soils. In addition, some
plants biomass production reduces may occur.
Abstract: In recent decades, particulate matter (PM10) have
received much attention due to its potential adverse health impact and
the subsequent need to better control or regulate these pollutants.
The aim of this paper is focused on study risk assessment of PM10
in four different districts (Shebikah, Masfalah, Aziziyah, Awali) in
Makkah, Saudi Arabia during the period from 1 Ramadan 1434 AH -
27 Safar 1435 AH. Samples were collected by using Low Volume
Sampler (LVS Low Volume Sampler) device and filtration method
for estimating the total concentration of PM10.
The study indicated that the mean PM10 concentrations were 254.6
(186.1 - 343.2) μg/m3 in Shebikah, 184.9 (145.6 - 271.4) μg/m3 in
Masfalah, 162.4 (92.4-253.8) μg/m3 in Aziziyah, and 56.0 (44.5 -
119.8) μg/m3 in Awali. These values did not exceed the permissible
limits in PME (340 μg/m3 as daily average). Furthermore, health
assessment is carried out using AirQ2.2.3 model to estimate the
number of hospital admissions due to respiratory diseases. The
cumulative number of cases per 100,000 were 1534 (18-3050 case),
which lower than that recorded in the United States, Malaysia. The
concentration response coefficient was 0.49 (95% CI 0.05 - 0.70) per
10 μg/m3 increase of PM10.
Abstract: Traditionally, the embodied energy of design choices
which reduce operational energy were assumed to have a negligible
impact on the life cycle energy of buildings. However with new
buildings having considerably lower operational energy, the
significance of embodied energy increases. A life cycle assessment of
a population of house designs was conducted in a mild and mixed
climate zone. It was determined not only that embodied energy
dominates life cycle energy, but that the impact on embodied of
design choices was of equal significance to the impact on operational
energy.
Abstract: This paper aims to project the construction of a
prototype azimuthal thruster, mounted with materials of low cost and
easy access, testing in a controlled environment to measure their
performance, characteristics and feasibility of future projects. The
construction of the simulation of dynamic positioning software,
responsible for simulating a vessel and reposition it when necessary.
Validation tests were performed in the form of partial or complete
system. These tests validate the system manually or automatically.
The system provides an interface to the user and simulates the
conditions unfavorable positioning of a vessel, accurately calculates
the azimuth angle, the direction of rotation of the helix and the time
that this should be turned on so that the vessel back to position
original. A serial communication connects the Simulation Dynamic
Positioning System with Embedded System causing the usergenerated
data to simulate the DP system arrives in the form of
control signals to the motors of the propellant. This article addresses
issues in the marine industry employees.
Abstract: The using of waste materials in the construction
industry can reduce the dependence on the natural aggregates which
are going at the end to deplete. The glass waste is generated in a huge
amount which can make one of its disposals in concrete industry
effective not only as a green solution but also as an advantage to
enhance the performance of mechanical properties and durability of
concrete. This article reports the performance of concrete specimens
containing different percentages of milled glass waste as a partial
replacement of cement (Powder), when they are subject to cycles of
freezing and thawing. The tests were conducted on 75-mm cubes and
75 x 75 x 300-mm prisms. Compressive strength based on laboratory
testing and non-destructive ultrasonic pulse velocity test were
performed during the action of freezing-thawing cycles (F/T). The
results revealed that the incorporation of glass waste in concrete
mixtures is not only feasible but also showed generally better strength
and durability performance than control concrete mixture. It may be
said that the recycling of waste glass in concrete mixes is not only a
disposal way, but also it can be an exploitation in concrete industry.
Abstract: In light of the technological development and its
introduction into the field of education, an online course was
designed in parallel to the 'conventional' course for teaching the
''Qualitative Research Methods''. This course aimed to characterize
learning-teaching processes in a 'Qualitative Research Methods'
course studied in two different frameworks. Moreover, its objective
was to explore the difference between the culture of a physical
learning environment and that of online learning. The research
monitored four learner groups, a total of 72 students, for two years,
two groups from the two course frameworks each year. The courses
were obligatory for M.Ed. students at an academic college of
education and were given by one female-lecturer. The research was
conducted in the qualitative method as a case study in order to attain
insights about occurrences in the actual contexts and sites in which
they transpire. The research tools were open-ended questionnaire and
reflections in the form of vignettes (meaningful short pictures) to all
students as well as an interview with the lecturer. The tools facilitated
not only triangulation but also collecting data consisting of voices
and pictures of teaching and learning. The most prominent findings
are: differences between the two courses in the change features of the
learning environment culture for the acquisition of contents and
qualitative research tools. They were manifested by teaching
methods, illustration aids, lecturer's profile and students' profile.
Abstract: SARA is a common and serious metabolic disorder in
early lactation in dairy cattle and in finishing beef cattle, caused by
diets with high inclusion of cereal grain. This experiment was
performed to determine the efficacy of Megasphaera elsdenii, a
major lactate-utilizing bacterium in prevention/treatment of SARA in
vivo. In vivo experimentation, it was used eight ruminally cannulated
rams and it was applied the rapid adaptation with the mixture of grain
based on wheat (80% wheat, 20% barley) and barley (80% barley,
20% wheat). During the systematic adaptation, it was followed the
probability of SARA formation by being measured the rumen pH
with two hours intervals after and before feeding. After being
evaluated the data, it was determined the ruminal pH ranged from
5.2-5.6 on the condition of feeding with 60 percentage of grain
mixture based on barley and wheat, that assured the definite form of
subacute acidosis. In four days SARA period, M. elsdenii (1010 cfu
ml-1) was inoculated during the first two days. During the SARA
period, it was observed the decrease of feed intake with M. elsdenii
inoculation. Inoculation of M. elsdenii was caused to differentiation
of rumen pH (P
Abstract: The work aims to develop a robot in the form of
autonomous vehicle to detect, inspection and mapping of
underground pipelines through the ATmega328 Arduino platform.
Hardware prototyping is very similar to C / C ++ language that
facilitates its use in robotics open source, resembles PLC used in
large industrial processes. The robot will traverse the surface
independently of direct human action, in order to automate the
process of detecting buried pipes, guided by electromagnetic
induction. The induction comes from coils that send the signal to the
Arduino microcontroller contained in that will make the difference in
intensity and the treatment of the information, and then this
determines actions to electrical components such as relays and
motors, allowing the prototype to move on the surface and getting the
necessary information. This change of direction is performed by a
stepper motor with a servo motor. The robot was developed by
electrical and electronic assemblies that allowed test your application.
The assembly is made up of metal detector coils, circuit boards and
microprocessor, which interconnected circuits previously developed
can determine, process control and mechanical actions for a robot
(autonomous car) that will make the detection and mapping of buried
pipelines plates. This type of prototype can prevent and identifies
possible landslides and they can prevent the buried pipelines suffer an
external pressure on the walls with the possibility of oil leakage and
thus pollute the environment.
Abstract: The rapid growth of multimedia technology demands
the secure and efficient access to information. This fast growing lose
the confidence of unauthorized duplication. Henceforth the protection
of multimedia content is becoming more important. Watermarking
solves the issue of unlawful copy of advanced data. In this paper,
blind video watermarking technique has been proposed. A luminance
layer of selected frames is interlaced into two even and odd rows of
an image, further it is deinterlaced and equalizes the coefficients of
the two shares. Color watermark is split into different blocks, and the
pieces of block are concealed in one of the share under the wavelet
transform. Stack the two images into a single image by introducing
interlaced even and odd rows in the two shares. Finally, chrominance
bands are concatenated with the watermarked luminance band. The
safeguard level of the secret information is high, and it is
undetectable. Results show that the quality of the video is not
changed also yields the better PSNR values.
Abstract: This study suggests the estimation method of stress
distribution for the beam structures based on TLS (Terrestrial Laser
Scanning). The main components of method are the creation of the
lattices of raw data from TLS to satisfy the suitable condition and
application of CSSI (Cubic Smoothing Spline Interpolation) for
estimating stress distribution. Estimation of stress distribution for the
structural member or the whole structure is one of the important
factors for safety evaluation of the structure. Existing sensors which
include ESG (Electric strain gauge) and LVDT (Linear Variable
Differential Transformer) can be categorized as contact type sensor
which should be installed on the structural members and also there are
various limitations such as the need of separate space where the
network cables are installed and the difficulty of access for sensor
installation in real buildings. To overcome these problems inherent in
the contact type sensors, TLS system of LiDAR (light detection and
ranging), which can measure the displacement of a target in a long
range without the influence of surrounding environment and also get
the whole shape of the structure, has been applied to the field of
structural health monitoring. The important characteristic of TLS
measuring is a formation of point clouds which has many points
including the local coordinate. Point clouds are not linear distribution
but dispersed shape. Thus, to analyze point clouds, the interpolation is
needed vitally. Through formation of averaged lattices and CSSI for
the raw data, the method which can estimate the displacement of
simple beam was developed. Also, the developed method can be
extended to calculate the strain and finally applicable to estimate a
stress distribution of a structural member. To verify the validity of the
method, the loading test on a simple beam was conducted and TLS
measured it. Through a comparison of the estimated stress and
reference stress, the validity of the method is confirmed.
Abstract: The main objective of this study was to assess the
seasonal variation of atmospheric polycyclic aromatic hydrocarbon
(PAH) concentrations associated with PM10 in an urban site of Győr,
Hungary. A total of 112 PM10 aerosol samples were collected in the
years of 2012 and 2013 and analyzed for PAHs by gas
chromatography method. The total PAH concentrations (sum of the
concentrations of 19 individual PAH compounds) ranged from 0.19
to 70.16 ng/m3 with the mean value of 12.29 ng/m3. Higher
concentrations of both total PAHs and benzo[a]pyrene (BaP) were
detected in samples collected in the heating seasons. Using BaPequivalent
potency index on the carcinogenic PAH concentration
data, the local population appears to be exposed to significantly
higher cancer risk in the heating seasons. However, the comparison
of the BaP and total PAH concentrations observed for Győr with
other cities it was found that the PAH levels in Győr generally
corresponded to the EU average.
Abstract: Since 1920, the industry has almost completely
changed the rivets production techniques for the manufacture of
permanent welding join production of structures and manufacture of
other products. The welding arc is the process more widely used in
industries. This is accomplished by the heat of an electric arc which
melts the base metal while the molten metal droplets are transferred
through the arc to the welding pool, protected from the atmosphere
by a gas curtain. The GMAW (Gas metal arc welding) process is
influenced by variables such as: current, polarity, welding speed,
electrode: extension, position, moving direction; type of joint,
welder's ability, among others. It is remarkable that the knowledge
and control of these variables are essential for obtaining satisfactory
quality welds, knowing that are interconnected so that changes in one
of them requiring changes in one or more of the other to produce the
desired results. The optimum values are affected by the type of base
metal, the electrode composition, the welding position and the quality
requirements. Thus, this paper proposes a new methodology, adding
the variable vibration through a mechanism developed for GMAW
welding, in order to improve the mechanical and metallurgical
properties which does not affect the ability of the welder and enables
repeatability of the welds made. For confirmation metallographic
analysis and mechanical tests were made.
Abstract: While choosing insulating oil, characteristic features
such as thermal cooling, endurance, efficiency and being
environment-friendly should be considered. Mineral oils are referred
as petroleum-based oil. In this study, vegetable oils investigated as an
alternative insulating liquid to mineral oil. Dissipation factor,
breakdown voltage, relative dielectric constant and resistivity
changes with the frequency and voltage of mineral, rapeseed and nut
oils were measured. Experimental studies were performed according
to ASTM D924 and IEC 60156 standards.