Abstract: High temperature Fischer-Tropsch synthesis process
use fixed fluidized bed as a reactor. In order to understand the flow
behavior in the fluidized bed better, the research of how the radial
velocity affects the entire flow field is necessary. Laser Doppler
Velocimetry (LDV) was used to study the radial velocity distribution
along the diameter direction of the cross-section of the particle in a
fixed fluidized bed. The velocity in the cross-section is fluctuating
within a small range. The direction of the speed is a random
phenomenon. In addition to r/R is 1, the axial velocity are more than 6
times of the radial velocity, the radial velocity has little impact on the
axial velocity in a fixed fluidized bed.
Abstract: A new approach has been developed to estimate the
load share and distribution of worm gear drives, and to calculate the
instantaneous tooth meshing stiffness. In the approach, the worm gear
drive was modelled as a series of spur gear slices, and each slice was
analyzed separately using the well-established formulae of spur gear
loading and stresses. By combining the results obtained for all slices,
the entire envolute worm gear set loading and stressing was obtained. The geometric modelling method presented allows tooth elastic
deformation and tooth root stresses of worm gear drives under
different load conditions to be investigated. Based on the slicing
method introduced in this study, the instantaneous meshing stiffness
and load share are obtained. In comparison with existing methods,
this approach has both good analysis accuracy and less computing
time.
Abstract: Carefully scheduling the operations of pumps can be
resulted to significant energy savings. Schedules can be defined
either implicit, in terms of other elements of the network such as tank
levels, or explicit by specifying the time during which each pump is
on/off. In this study, two new explicit representations based on timecontrolled
triggers were analyzed, where the maximum number of
pump switches was established beforehand, and the schedule may
contain fewer switches than the maximum. The optimal operation of
pumping stations was determined using a Jumping Particle Swarm
Optimization (JPSO) algorithm to achieve the minimum energy cost.
The model integrates JPSO optimizer and EPANET hydraulic
network solver. The optimal pump operation schedule of VanZyl
water distribution system was determined using the proposed model
and compared with those from Genetic and Ant Colony algorithms.
The results indicate that the proposed model utilizing the JPSO
algorithm is a versatile management model for the operation of realworld
water distribution system.
Abstract: The system of ordinary nonlinear differential
equations describing sliding velocity during impact with friction for a
three-dimensional rigid-multibody system is developed. No analytical
solutions have been obtained before for this highly nonlinear system.
Hence, a power series solution is proposed. Since the validity of this
solution is limited to its convergence zone, a suitable time step is
chosen and at the end of it a new series solution is constructed. For a
case study, the trajectory of the sliding velocity using the proposed
method is built using 6 time steps, which coincides with a Runge-
Kutta solution using 38 time steps.
Abstract: Healthcare safety has been perceived important. It is
essential to prevent troubles in healthcare processes for healthcare
safety. Trouble prevention is based on trouble prediction using
accumulated knowledge on processes, troubles, and countermeasures.
However, information on troubles has not been accumulated in
hospitals in the appropriate structure, and it has not been utilized
effectively to prevent troubles. In the previous study, however a
detailed knowledge acquisition process for trouble prediction was
proposed, the knowledgebase for countermeasures was not involved.
In this paper, we aim to propose the structure of the knowledgebase for
countermeasures, in the knowledge acquisition process for trouble
prediction in healthcare process. We first design the structure of
countermeasures and propose the knowledge representation form on
countermeasures. Then, we evaluate the validity of the proposal, by
applying it into an actual hospital.
Abstract: The current study aims to highlight the loading
characteristics impact on the time evolution (focusing particularly on
long term effects) of the deformation of realized reinforced concrete
beams. Namely the tension stiffening code provisions (i.e. within
Eurocode 2) are reviewed with a clear intention to reassess their
operational value and predicting capacity. In what follows the
experimental programme adopted along with some preliminary
findings and numerical modeling attempts are presented. For a range of long slender reinforced concrete simply supported
beams (4200 mm) constant static sustained and repeated cyclic
loadings were applied mapping the time evolution of deformation.
All experiments were carried out at the Heavy Structures Lab of the
University of Leeds. During tests the mid-span deflection, creep
coefficient and shrinkage strains were monitored for duration of 90
days. The obtained results are set against the values predicted by
Eurocode 2 and the tools within an FE commercial package (i.e.
Midas FEA) to yield that existing knowledge and practise is at times
over-conservative.
Abstract: For the shrimp companies to remain relevant to its local
and international consumers, they must offer new shrimp product and
services. It must work actively not just to create value for the consumer,
but to involve the consumer in co-creating value for shrimp product
innovation in the market. In this theoretical work, we conceptualize the
business concept of value co-creation in the context of shrimp products,
and propose a framework of value co-creation for shrimp product
innovation in shrimp industries. With guidance on value co-creation in
in shrimp industry, and shrimp value chain actors mapped to the
co-creation cycle, companies can use the framework to offer new
shrimp product to consumer communities. Although customer
co-creation is known approach in the world, it is not commonly used
by the companies in Bangladesh. This paper makes an original
contribution by conceptualizing co-creation and set the examples of
best co-creation practices in food sector. The results of the study
provide management with guidelines for successful co-creation
projects with an innovation- and market-oriented approach. The
framework also provides a basis for further research in this area.
Abstract: Drought is one of the most serious problems posing a
grave threat to cereals production including maize. Maize
improvement in drought-stress tolerance poses a great challenge as
the global need for food and bio-energy increases. Thus, the current
study was planned to explore the variations and determine the
performance of target traits of maize hybrids at grain growth stage
under drought conditions during 2014 under Adana, Mediterranean
climate conditions, Turkey. Maize hybrids (Sancia, Indaco,
71May69, Aaccel, Calgary, 70May82, 72May80) were evaluated
under (irrigated and water stress). Results revealed that, grain yield
and yield traits had a negative effects because of water stress
conditions compared with the normal irrigation. As well as, based on
the result under normal irrigation, the maximum biological yield and
harvest index were recorded. According to the differences among
hybrids were found that, significant differences were observed among
hybrids with respect to yield and yield traits under current research. Based on the results, grain weight had more effect on grain yield
than grain number during grain filling growth stage under water
stress conditions. In this concern, according to low drought
susceptibility index (less grain yield losses), the hybrid (Indaco) was
more stable in grain number and grain weight. Consequently, it may
be concluded that this hybrid would be recommended for use in the
future breeding programs for production of drought tolerant hybrids.
Abstract: This paper presents the modeling approach in SBO
sequence for VVER 1000 reactors and describes the reactor core
behavior at late in-vessel phase in case of late reflooding by HPIS
and gives preliminary results for the ASTECv2 validation. The work
is focused on investigation of plant behavior during total loss of
power and the operator actions. The main goal of these analyses is to
assess the phenomena arising during the Station blackout (SBO)
followed by primary side high pressure injection system (HPIS)
reflooding of already damaged reactor core at very late “in-vessel”
phase. The purpose of the analyses is to define how the later HPIS
switching on can delay the time of vessel failure or possibly avoid
vessel failure. The times for HPP injection were chosen based on
previously performed investigations.
Abstract: Oxygen Reduction Reaction (ORR) performance of
iron and nitrogen co-doped porous carbon nanoparticles (Fe-NPC)
with various physical and (electro) chemical properties have been
investigated. Fe-NPC nanoparticles are synthesized via a facile
soft-templating procedure by using Iron (III) chloride hexa-hydrate as
iron precursor and aminophenol-formaldehyde resin as both carbon
and nitrogen precursor. Fe-NPC nanoparticles shows high surface area
(443.83 m2g-1), high pore volume (0.52 m3g-1), narrow mesopore size
distribution (ca. 3.8 nm), high conductivity (IG/ID=1.04), high kinetic
limiting current (11.71 mAcm-2) and more positive onset potential
(-0.106 V) compared to metal-free NPC nanoparticles (-0.295V)
which make it high efficient ORR metal-free catalysts in alkaline
solution. This study may pave the way of feasibly designing iron and
nitrogen containing carbon materials (Fe-N-C) for highly efficient
oxygen reduction electro-catalysis.
Abstract: A sliding door system is used in commercial vehicles
and passenger cars to allow a larger unobstructed access to the
interior for loading and unloading. The movement of a sliding door
on vehicle body is ensured by mechanisms and tracks having special
cross-section which is manufactured by roll forming and stretch
bending process. There are three tracks and three mechanisms which
are called upper, central and lower on a sliding door system. There
are static requirements as strength on different directions, rigidity for
mechanisms, door drop off, door sag; dynamic requirements as high
energy slam opening-closing and durability requirement to validate
these products. In addition, there is a kinematic requirement to find
out force values from door handle during manual operating. In this
study, finite element analysis and physical test results which are
realized for sliding door systems will be shared comparatively.
Abstract: In Automotive Industry, sliding door systems that are
also used as body closures are safety members. Extreme product tests
are realized to prevent failures in design process, but these tests
realized experimentally result in high costs. Finite element analysis is
an effective tool used for design process. These analyses are used
before production of prototype for validation of design according to
customer requirement. In result of this, substantial amount of time
and cost is saved. Finite element model is created for geometries that are designed in
3D CAD programs. Different element types as bar, shell and solid,
can be used for creating mesh model. Cheaper model can be created
by selection of element type, but combination of element type that
was used in model, number and geometry of element and degrees of
freedom affects the analysis result. Sliding door system is a good
example which used these methods for this study. Structural analysis
was realized for sliding door mechanism by using FE models. As
well, physical tests that have same boundary conditions with FE
models were realized. Comparison study for these element types,
were done regarding test and analyses results then optimum
combination was achieved.
Abstract: One of the fundamental characteristics of Information
and Communication Technology (ICT) has been the ever-changing
nature of continuous release and models of ICTs with its impact on
the academic, social, and psychological benefits of its introduction in
schools. However, there seems to be a growing concern about its
negative impact on students when introduced early in schools for
teaching and learning. This study aims to design a model of child
development factors affecting the early introduction of ICTs in
schools in an attempt to improve the understanding of child
development and introduction of ICTs in schools. The proposed
model is based on a sound theoretical framework. It was designed
following a literature review of child development theories and child
development factors. The child development theoretical framework
that fitted to the best of all child development factors was then chosen
as the basis for the proposed model. This study hence found that the
Jean Piaget cognitive developmental theory is the most adequate
theoretical frameworks for modeling child development factors for
ICT introduction in schools.
Abstract: Damaturu is the capital of Yobe State in northeastern
Nigeria where civic amenities and facilities are not adequate even
after 24 years of its existence. The volatile security and political
situations are most significant causes for the same. The basic facility
for the citizens in terms of drinking water and electricity are not
available. For the drinking water, they have to rely on personal
boreholes or the filtered borehole waters available in packaged
sachets in market. The present study is concerned with environmental
impact of indiscriminate disposal of drinking synthetic polythene
water sachets in Damaturu. The sachet water is popularly called as
“pure water”, but its purity is questionable. Increased production and
consumption of sachet water has led to indiscriminate dumping and
disposal of empty sachets leading to serious environmental threat.
The evidence of this is seen for sachets littering the streets and the
drainages blocked by ‘blocks’ of water sachet waste. Sachet water
gained much popularity in Nigeria because the product is convenient
for use, affordable and economically viable. The present study aims
to find out the solution to this environmental problem. The fieldbased
study has found some significant factors that cause
environmental and socio economic effect due to this. Some
recommendations have been made based on research findings
regarding sustainable waste management, recycling and re-use of the
non-biodegradable products in society.
Abstract: In this study, failure analysis of pipe system at a micro
hydroelectric power plant is investigated. Failure occurred at the pipe
system in the powerhouse during shut down operation of the water
flow by a valve. This locking had caused a sudden shock wave, also
called “Water-hammer effect”, resulting in noise and inside pressure
increase. After visual investigation of the effect of the shock wave on
the system, a circumference crack was observed at the pipe flange
weld region. To establish the reason for crack formation, calculations
of pressure and stress values at pipe, flange and welding seams were
carried out and concluded that safety factor was high (2.2), indicating
that no faulty design existed. By further analysis, pipe system and
hydroelectric power plant was examined. After observations it is
determined that the plant did not include a ventilation nozzle (air
trap), that prevents the system of sudden pressure increase inside the
pipes which is caused by water-hammer effect. Analyses were carried
out to identify the influence of water-hammer effect on inside
pressure increase and it was concluded that, according Jowkowsky’s
equation, shut down time is effective on inside pressure increase. The
valve closing time was uncertain but by a shut down time of even one
minute, inside pressure would increase by 7.6 bar (working pressure
was 34.6 bar). Detailed investigations were also carried out on the
assembly of the pipe-flange system by considering technical
drawings. It was concluded that the pipe-flange system was not
installed according to the instructions. Two of five weld seams were
not applied and one weld was carried out faulty. This incorrect and
inadequate weld seams resulted in; insufficient connection of the pipe
to the flange constituting a strong notch effect at weld seam regions,
increase in stress values and the decrease of strength and safety
factor.
Abstract: Erosion and abrasion are wear mechanisms reducing
the lifetime of machine elements like valves, pump and pipe systems.
Both wear mechanisms are acting at the same time, causing a
“Synergy” effect, which leads to a rapid damage of the surface.
Different parameters are effective on erosive abrasive wear rate. In
this study effect of particle impact angle on wear rate and wear
mechanism of ductile and brittle materials was investigated. A new
slurry pot was designed for experimental investigation. As abrasive
particle, silica sand was used. Particle size was ranking between 200-
500 μm. All tests were carried out in a sand-water mixture of 20%
concentration for four hours. Impact velocities of the particles were
4.76 m/s. As ductile material steel St 37 with Vickers Hardness
Number (VHN) of 245 and quenched St 37 with 510 VHN was used
as brittle material. After wear tests, morphology of the eroded
surfaces were investigated for better understanding of the wear
mechanisms acting at different impact angles by using Scanning
Electron Microscope. The results indicated that wear rate of ductile
material was higher than brittle material. Maximum wear rate was
observed by ductile material at a particle impact angle of 300 and
decreased further by an increase in attack angle. Maximum wear rate
by brittle materials was by impact angle of 450 and decreased further
up to 900. Ploughing was the dominant wear mechanism by ductile
material. Microcracks on the surface were detected by ductile
materials, which are nucleation centers for crater formation. Number
of craters decreased and depth of craters increased by ductile
materials by attack angle higher than 300. Deformation wear
mechanism was observed by brittle materials. Number and depth of
pits decreased by brittle materials by impact angles higher than 450.
At the end it is concluded that wear rate could not be directly related
to impact angle of particles due to the different reaction of ductile and
brittle materials.
Abstract: Nitrification is essential to biological processes
designed to remove ammonia and/or total nitrogen. It removes excess
nitrogenous compound in wastewater which could be very toxic to
the aquatic fauna or cause serious imbalance of such aquatic
ecosystem. Efficient nitrification is linked to an in-depth knowledge
of the structure and dynamics of the nitrifying community structure
within the wastewater treatment systems. In this study, molecular
technique was employed for characterizing the microbial structure of
activated sludge [ammonia oxidizing bacteria (AOB) and nitrite
oxidizing bacteria (NOB)] in a municipal wastewater treatment with
intention of linking it to the plant efficiency. PCR based phylogenetic
analysis was also carried out. The average operating and
environmental parameters as well as specific nitrification rate of plant
was investigated during the study. During the investigation the average temperature was 23±1.5oC.
Other operational parameters such as mixed liquor suspended solids
and chemical oxygen demand inversely correlated with ammonia
removal. The dissolved oxygen level in the plant was constantly
lower than the optimum (between 0.24 and 1.267 mg/l) during this
study. The plant was treating wastewater with influent ammonia
concentration of 31.69 and 24.47 mg/L. The influent flow rates
(ML/Day) was 96.81 during period. The dominant nitrifiers include:
Nitrosomonas spp. Nitrobacter spp. and Nitrospira spp. The AOB
had correlation with nitrification efficiency and temperature. This
study shows that the specific ammonia oxidizing rate and the specific
nitrate formation rates can serve as good indicator of the plant overall
nitrification performance.
Abstract: This paper addresses minimizing the makespan of the
distributed permutation flow shop scheduling problem. In this
problem, there are several parallel identical factories or flowshops
each with series of similar machines. Each job should be allocated to
one of the factories and all of the operations of the jobs should be
performed in the allocated factory. This problem has recently gained
attention and due to NP-Hard nature of the problem, metaheuristic
algorithms have been proposed to tackle it. Majority of the proposed
algorithms require large computational time which is the main
drawback. In this study, a general variable neighborhood search
algorithm (GVNS) is proposed where several time-saving schemes
have been incorporated into it. Also, the GVNS uses the sophisticated
method to change the shaking procedure or perturbation depending
on the progress of the incumbent solution to prevent stagnation of the
search. The performance of the proposed algorithm is compared to
the state-of-the-art algorithms based on standard benchmark
instances.
Abstract: Polymeric micro-cantilevers (Cs) are rapidly
becoming popular for MEMS applications such as chemo- and biosensing
as well as purely electromechanical applications such as
microrelays. Polymer materials present suitable physical and
chemical properties combined with low-cost mass production. Hence,
micro-cantilevers made of polymers indicate much more
biocompatibility and adaptability of rapid prototyping along with
mechanical properties. This research studies the effects of three
process and one size factors on the filling behaviour in micro cavity,
and the role of each in the replication of micro parts using different
polymer materials i.e. polypropylene (PP) SABIC 56M10 and
acrylonitrile butadiene styrene (ABS) Magnum 8434 . In particular,
the following factors are considered: barrel temperature, mould
temperature, injection speed and the thickness of micro features. The
study revealed that the barrel temperature and the injection speed are
the key factors affecting the flow length of micro features replicated
in PP and ABS. For both materials, an increase of feature sizes
improves the melt flow. However, the melt fill of micro features does
not increase linearly with the increase of their thickness.
Abstract: Hollow section for bridge columns has some
advantages. However, current seismic design codes do not provide
design regulations for hollow bridge piers. There have been many
experimental studied for hollow reinforced concrete piers in the world.
But, Study for hollow section for bridge piers in Korea has been begun
with approximately 2000s. There has been conducted experimental
study for hollow piers of flexural controlled sections by Yeungnam
University, Sung kyunkwan University, Korea Expressway
Corporation in 2009. This study concluded that flexural controlled
sections for hollow piers showed the similar behavior to solid sections.
And there have been conducted experimental study for hollow piers of
compression controlled sections by Yeungnam University, Korea
Institute of Construction Technology in 2012. This study concluded
that compression controlled sections for hollow piers showed
compression fracture of concrete in inside wall face. Samsung
Construction & Trading Corporation has been conducted study with
Yeungnam University for reduce the quantity of reinforcement details
about hollow piers. Reduce the quantity of reinforcement details are
triangular cross tie. This study concluded that triangular reinforcement
details showed the similar behavior as compared with existing
reinforcement details.