Abstract: The new era of digital communication has brought up
many challenges that network operators need to overcome. The high
demand of mobile data rates require improved networks, which is a
challenge for the operators in terms of maintaining the quality of
experience (QoE) for their consumers. In live video transmission,
there is a sheer need for live surveillance of the videos in order to
maintain the quality of the network. For this purpose objective
algorithms are employed to monitor the quality of the videos that are
transmitted over a network. In order to test these objective algorithms,
subjective quality assessment of the streamed videos is required, as the
human eye is the best source of perceptual assessment. In this paper we
have conducted subjective evaluation of videos with varying spatial
and temporal impairments. These videos were impaired with frame
freezing distortions so that the impact of frame freezing on the quality
of experience could be studied. We present subjective Mean Opinion
Score (MOS) for these videos that can be used for fine tuning the
objective algorithms for video quality assessment.
Abstract: Fibre cement plates, often used in construction,
generally are made using quartz as an inert material, cement as a
binder and cellulose as a fibre. This paper, first of all, investigates the
mechanical properties and durability of fibre cement plates when
quartz is both partly and fully replaced with diatomite. Diatomite
does not only have lower density compared to quartz but also has
high pozzolanic activity. The main objective of this paper is the
investigation of the effects of supplementary cementing materials
(SCMs) on the short and long term mechanical properties and
durability characteristics of fibre cement plates prepared using
diatomite. Supplementary cementing materials such as ground
granulated blast furnace slug (GGBS) and fly ash (FA) are used in
this study. Volume proportions of 10, 20, 30 and 40% of GGBS and
FA are used as partial replacement materials to cement. Short and
long term mechanical properties such as compressive and flexural
strengths as well as sorptivity characteristics and mass were
investigated. Consistency and setting time at each replacement levels
of SCMs were also recorded. The effects of using supplementary
cementing materials on the carbonation and sulphate resistance of
fibre cement plates were then experimented. The results, first of all,
show that the use of diatomite as a full or partial replacement to
quartz resulted in a systematic decrease in total mass of the fibre
cement plates. The reduction of mass was largely due to the lower
density and finer particle size of diatomite compared to quartz. The
use of diatomite did not only reduce the mass of these plates but also
increased the compressive strength significantly as a result of its high
pozzolanic activity. The replacement levels of both GGBS and FA
resulted in a systematic decrease in short term compressive strength
with increasing replacement levels. This was essentially expected as
the total rate of hydration is much lower in GGBS and FA than that
of cement. Long term results however, indicated that the compressive
strength of fibre cement plates prepared using both GGBS and FA
increases with time and hence the compressive strength of plates
prepared using SCMs is either equivalent or more than the
compressive strength of plates prepared using cement alone.
Durability characteristics of fibre cement plates prepared using SCMs
were enhanced significantly. Measurements of sopritivty
characteristics were also indicated that the plates prepared using
SCMs has much lower water absorption capacities compared to
plates prepared cement alone. Much higher resistance to carbonation
and sulphate attach were observed with plates prepared using SCMs.
The results presented in this paper show that the use of SCMs does
not only support the production of more sustainable construction
materials but also enhances the mechanical properties and durability
characteristics of fibre cement plates.
Abstract: This paper presents a new automatic vehicle detection
method from very high resolution aerial images to measure traffic
density. The proposed method starts by extracting road regions from
image using road vector data. Then, the road image is divided into
equal sections considering resolution of the images. Gradient vectors
of the road image are computed from edge map of the corresponding
image. Gradient vectors on the each boundary of the sections are
divided where the gradient vectors significantly change their
directions. Finally, number of vehicles in each section is carried out
by calculating the standard deviation of the gradient vectors in each
group and accepting the group as vehicle that has standard deviation
above predefined threshold value. The proposed method was tested in
four very high resolution aerial images acquired from Istanbul,
Turkey which illustrate roads and vehicles with diverse
characteristics. The results show the reliability of the proposed
method in detecting vehicles by producing 86% overall F1 accuracy
value.
Abstract: The aim of this research is to clarify the difference by
industry segment or product characteristics as regards organisation
management for an open innovation to raise R&D performance. In
particular, the trait of the pharmaceutical industry is defined in
comparison with IT component industry segment. In considering open
innovation, both inter-organisational relation and the management in
an organisation are important issues. As methodology, a questionnaire
was conducted. In conclusion, suitable organisation management
according to the difference in industry segment or product
characteristics became clear.
Abstract: Background in music analysis: Traditionally, when we
think about a composer’s sketches, the chances are that we are
thinking in terms of the working out of detail, rather than the
evolution of an overall concept. Since music is a “time art,” it follows
that questions of a form cannot be entirely detached from
considerations of time. One could say that composers tend to regard
time either as a place gradually and partially intuitively filled, or they
can look for a specific strategy to occupy it. It seems that the one
thing that sheds light on Stockhausen’s compositional thinking is his
frequent use of “form schemas,” that is often a single-page
representation of the entire structure of a piece.
Background in music technology: Sonic Visualiser is a program
used to study a musical recording. It is an open source application for
viewing, analyzing, and annotating music audio files. It contains a
number of visualisation tools, which are designed with useful default
parameters for musical analysis. Additionally, the Vamp plugin
format of SV supports to provide analysis such as for example
structural segmentation.
Aims: The aim of paper is to show how SV may be used to obtain
a better understanding of the specific musical work, and how the
compositional strategy does impact on musical structures and musical
surfaces. It is known that “traditional” music analytic methods don’t
allow indicating interrelationships between musical surface (which is
perceived) and underlying musical/acoustical structure.
Main Contribution: Stockhausen had dealt with the most diverse
musical problems by the most varied methods. A characteristic which
he had never ceased to be placed at the center of his thought and
works, it was the quest for a new balance founded upon an acute
connection between speculation and intuition. In the case with
Mikrophonie I (1964) for tam-tam and 6 players Stockhausen makes
a distinction between the “connection scheme,” which indicates the
ground rules underlying all versions, and the form scheme, which is
associated with a particular version. The preface to the published
score includes both the connection scheme, and a single instance of a
“form scheme,” which is what one can hear on the CD recording. In
the current study, the insight into the compositional strategy chosen
by Stockhausen was been compared with auditory image, that is, with
the perceived musical surface. Stockhausen’s musical work is
analyzed both in terms of melodic/voice and timbre evolution.
Implications: The current study shows how musical structures
have determined of musical surface. The general assumption is this,
that while listening to music we can extract basic kinds of musical
information from musical surfaces. It is shown that interactive
strategies of musical structure analysis can offer a very fruitful way
of looking directly into certain structural features of music.
Abstract: In the field of fashion design, 3D Mannequin is a kind
of assisting tool which could rapidly realize the design concepts.
While the concept of 3D Mannequin is applied to the computer added
fashion design, it will connect with the development and the
application of design platform and system. Thus, the situation
mentioned above revealed a truth that it is very critical to develop a
module of 3D Mannequin which would correspond with the necessity
of fashion design. This research proposes a concrete plan that
developing and constructing a system of 3D Mannequin with Kinect.
In the content, ergonomic measurements of objective human features
could be attained real-time through the implement with depth camera
of Kinect, and then the mesh morphing can be implemented through
transformed the locations of the control-points on the model by
inputting those ergonomic data to get an exclusive 3D mannequin
model. In the proposed methodology, after the scanned points from the
Kinect are revised for accuracy and smoothening, a complete human
feature would be reconstructed by the ICP algorithm with the method
of image processing. Also, the objective human feature could be
recognized to analyze and get real measurements. Furthermore, the
data of ergonomic measurements could be applied to shape morphing
for the division of 3D Mannequin reconstructed by feature curves. Due
to a standardized and customer-oriented 3D Mannequin would be
generated by the implement of subdivision, the research could be
applied to the fashion design or the presentation and display of 3D
virtual clothes. In order to examine the practicality of research
structure, a system of 3D Mannequin would be constructed with JAVA
program in this study. Through the revision of experiments the
practicability-contained research result would come out.
Abstract: UAV’s are small remote operated or automated aerial
surveillance systems without a human pilot aboard. UAV’s generally
finds its use in military and special operation application, a recent
growing trend in UAV’s finds its application in several civil and nonmilitary
works such as inspection of power or pipelines. The
objective of this paper is the augmentation of a UAV in order to
replace the existing expensive sonar (Sound Navigation And
Ranging) based equipment amongst small scale fisherman, for whom
access to sonar equipment are restricted due to limited economic
resources. The surveillance equipment’s present in the UAV will
relay data and GPS (Global Positioning System) location onto a
receiver on the fishing boat using RF signals, using which the
location of the schools of fishes can be found. In addition to this, an
emergency beacon system is present for rescue operations and drone
recovery.
Abstract: This article aims to analyze the static stability and
pseudostatic slope by using different methods such as: Bishop
method, Junbu, Ordinary, Morgenstern-price and GLE. The two
dimensional modeling of slope stability under various loading as: the
earthquake effect, the water level and road mobile charges. The
results show that the slope is stable in the static case without water,
but in other cases, the slope lost its stability and give unstable. The
calculation of safety factor is to evaluate the stability of the slope
using the limit equilibrium method despite the difference between the
results obtained by these methods that do not rely on the same
assumptions. In the end, the results of this study illuminate well the
influence of the action of water, moving loads and the earthquake on
the stability of the slope.
Abstract: Diagnostic enzymes like aspartate aminotransferase
(AST), alanine aminotransferase (ALT) and alkaline phosphatase
(ALP) were determined as indices of heavy metal pollution in Tilapia
guinensis. Three different sets of fishes treated with lead (Pb), iron
(Fe) and copper (Cu) were used for the study while a fourth group
with no heavy metal served as a control. Fishes in each of the groups
were exposed to 2.65mg/l of Pb, 0.85mg/l of Fe and 0.35 mg/l of Cu
in aerated aquaria for 96 hours. Tissue fractionation of the liver
tissues was carried out and the three diagnostic enzymes (AST, ALT,
and ALP) were estimated. Serum levels of the same diagnostic
enzymes were also measured. The mean values of the serum enzyme
activity for ALP in each experimental group were 19.5±1.62,
29.67±2.17 and 1.15±0.27 IU/L for Pb, Fe and Cu groups compared
with 9.99±1.34 IU/L enzyme activity in the control. This result
showed that Pb and Fe caused increased release of the enzyme into
the blood circulation indicating increased tissue damage while Cu
caused a reduction in the serum level as compared with the level in
the control group. The mean values of enzyme activity obtained in
the liver were 102.14±6.12, 140.17±2.06 and 168.23±3.52 IU/L for
Pb, Fe and Cu groups, respectively compared to 91.20±9.42 IU/L
enzyme activity for the control group. The serum and liver AST and
ALT activities obtained in Pb, Fe, Cu and control groups are
reported. It was generally noted that the presence of the heavy metal
caused liver tissues damage and consequent increased level of the
diagnostic enzymes in the serum.
Abstract: Rapid Prototyping (RP) technologies enable physical
parts to be produced from various materials without depending on the
conventional tooling. Fused Deposition Modeling (FDM) is one of
the famous RP processes used at present. Tensile strength and
compressive strength resistance will be identified for different sample
structures and different layer orientations of ABS rapid prototype
solid models. The samples will be fabricated by a FDM rapid
prototyping machine in different layer orientations with variations in
internal geometrical structure. The 0° orientation where layers were
deposited along the length of the samples displayed superior strength
and impact resistance over all the other orientations. The anisotropic
properties were probably caused by weak interlayer bonding and
interlayer porosity.
Abstract: Socio-economic development, which is seen around
the world today, has contributed to the emergence of new problems
of a social nature. Different political, historical, geographical or
economic conditions cause that, in addition to global issues of social
policy such as an aging population, unemployment, migration,
countries, regions, there are also specific new problems that require
diagnosis, individualized approach and efficient, planned solutions.
These should include, among others, digital addiction, peer violence,
obesity among children, the problem of ‘legal highs’, stress,
depression, diseases associated with environmental pollution etc. The
central authorities, selected most often with the tools specific to
representative democracy, that is, the general election, for many
reasons, inter alia, organizational, communication, are not able to
effectively diagnose their intensity, territorial distribution, and thus to
effectively fight them. This article aims to show how in Poland,
citizens influence solving problems related to the broader social
policy implemented at the local government level and indicates the
possibilities of improving those solutions. The conclusions of
theoretical analysis have been supported by empirical studies, which
tested the use of instruments of participatory democracy in the
planning and creation of communal strategies for solving social
problems in one of the Polish voivodeships.
Abstract: In recent years a new method of combination
treatment for cancer has been developed and studied that has led to
significant advancements in the field of cancer therapy. Hyperthermia
is a traditional therapy that, along with a creation of a medically
approved level of heat with the help of an alternating magnetic AC
current, results in the destruction of cancer cells by heat. This paper
gives details regarding the production of the spherical nanocomposite
PVA/γ-Fe2O3 in order to be used for medical purposes such as tumor
treatment by hyperthermia. To reach a suitable and evenly distributed
temperature, the nanocomposite with core-shell morphology and
spherical form within a 100 to 200 nanometer size was created using
phase separation emulsion, in which the magnetic nano-particles γ-
Fe2O3 with an average particle size of 20 nano-meters and with
different percentages of 0.2, 0.4, 0.5 and 0.6 were covered by
polyvinyl alcohol. The main concern in hyperthermia and heat
treatment is achieving desirable specific absorption rate (SAR) and
one of the most critical factors in SAR is particle size. In this project
all attempts has been done to reach minimal size and consequently
maximum SAR. The morphological analysis of the spherical
structure of the nanocomposite PVA/γ-Fe2O3 was achieved by SEM
analyses and the study of the chemical bonds created was made
possible by FTIR analysis. To investigate the manner of magnetic
nanocomposite particle size distribution a DLS experiment was
conducted. Moreover, to determine the magnetic behavior of the γ-
Fe2O3 particle and the nanocomposite PVA/γ-Fe2O3 in different
concentrations a VSM test was conducted. To sum up, creating
magnetic nanocomposites with a spherical morphology that would be
employed for drug loading opens doors to new approaches in
developing nanocomposites that provide efficient heat and a
controlled release of drug simultaneously inside the magnetic field,
which are among their positive characteristics that could significantly
improve the recovery process in patients.
Abstract: This paper describes the main features of a knowledge-based system evaluation method. System evaluation is placed in the context of a hybrid legal decision-support system, Advisory Support for Home Settlement in Divorce (ASHSD). Legal knowledge for ASHSD is represented in two forms, as rules and previously decided cases. Besides distinguishing the two different forms of knowledge representation, the paper outlines the actual use of these forms in a computational framework that is designed to generate a plausible solution for a given case, by using rule-based reasoning (RBR) and case-based reasoning (CBR) in an integrated environment. The nature of suitability assessment of a solution has been considered as a multiple criteria decision-making process in ASHAD evaluation. The evaluation was performed by a combination of discussions and questionnaires with different user groups. The answers to questionnaires used in this evaluations method have been measured as a fuzzy linguistic term. The finding suggests that fuzzy linguistic evaluation is practical and meaningful in knowledge-based system development purpose.
Abstract: The degradation of concrete due to various hygrochemo-
mechanical actions is inevitable for the structures particularly
built to store water. Therefore, it is essential to determine the material
properties of dam-like structures due to ageing to predict the behavior
of such structures after a certain age. The degraded material
properties are calculated by introducing isotropic degradation index.
The predicted material properties are used to study the behavior of
aged dam at different ages. The dam is modeled by finite elements
and displacement and is considered as an unknown variable. The
parametric study reveals that the displacement is quite larger for
comparatively lower design life of the structure because the
degradation of elastic properties depends on the design life of the
dam. The stresses in dam cam be unexpectedly large at any age with
in the design life. The outcomes of the present study indicate the
importance of the consideration ageing effect of concrete exposed to
water for the safe design of dam throughout its life time.
Abstract: This paper presents an experimental study on
structural performance of an innovative noise barrier consisting of
poly-block, light polyurethane foam (LPF) and polyurea. This wall
system (flexi-wall) is intended to be employed as a vertical extension
to existing sound barriers in an accelerated construction method. To
aid in the wall design, several mechanical tests were conducted on
LPF specimens and two full-scale walls were then fabricated
employing the same LPF material. The full-scale walls were
subjected to lateral loading in order to establish their lateral
resistance. A cyclic fatigue test was also performed on a full-scale
flexi-wall in order to evaluate the performance of the wall under a
repetitive loading condition. The result of the experiments indicated
the suitability of flexi-wall in accelerated construction and confirmed
that the structural performance of the wall system under lateral
loading is satisfactory for the sound barrier application. The
experimental results were discussed and a preliminary design
procedure for application of flexi-wall in sound barrier applications
was also developed.
Abstract: The Figaro AM-1 sensor module which employs TGS
2600 model gas sensor in air quality assessment was used. The
system was coupled with a microprocessor that enables sensor
module to create warning message via telephone. This low cot sensor
system’s performance was compared with a DiagNose II commercial
electronic nose system. Both air quality sensor and electronic nose
system employ metal oxide chemical gas sensors. In the study
experimental setup, data acquisition methods for electronic nose
system, and performance of the low cost air quality system were
evaluated and explained.
Abstract: Construction and reconstruction of settlements and
individual municipalities, environmental management and the
creation, deployment of the forces of production and building
transport and technical equipment requires a large expenditure of
material and human resources. That is why the economic aspects of
the majority decision in these planes built in the foreground and are
often decisive. Thereby but more serious is that the economic aspects
of the settlement, the creation and function remain in their whole,
unprocessed, and cannot speak of a set of individual techniques and
methods traditional indicators and experiments with new approaches.
This is true both at the level of the national economy, and in their
own urban designs. Still a few remain identified specific economic
shaping patterns of settlement and the less it is possible to speak of
their control. Also practical assessing economics of specific solutions
are often used non-apt indicators in addition to economics usually
identifies with the lowest acquisition cost or high-intensity land use
with little regard for functional efficiency and little studied much
higher operating and maintenance costs".
Abstract: This paper focuses on I/O optimizations of N-hybrid
(New-Form of hybrid), which provides a hybrid file system space
constructed on SSD and HDD. Although the promising potentials of
SSD, such as the absence of mechanical moving overhead and high
random I/O throughput, have drawn a lot of attentions from IT
enterprises, its high ratio of cost/capacity makes it less desirable to
build a large-scale data storage subsystem composed of only SSDs. In
this paper, we present N-hybrid that attempts to integrate the strengths
of SSD and HDD, to offer a single, large hybrid file system space.
Several experiments were conducted to verify the performance of
N-hybrid.
Abstract: Radial profiles of particle velocities were investigated
in a 6.1m high methanol-to-olefins cold model experimental device
using a TSI laser Doppler velocimeter. The effect of axial height on
flow development was not obvious in fully developed region under the
same operating condition. Superficial gas velocity and solid
circulating rate had significant influence on particle velocity in the
center region of the riser. Besides, comparisons among rising,
descending and average particle velocity were conducted. The particle
average velocity was similar to the rising particle velocity and higher
than the descending particle velocity in radial locations except the wall
region of riser.
Abstract: When printing a plate (or dish) by an FDM 3D printer,
the process normally requires support material, which causes several
problems. This paper proposes a method for forming thin plates
without using wasteful support material. This method requires several
extraordinary parameter values when slicing plates. The experiments
show that the plates can, for the most part, be successfully formed
using a conventional slicer and a 3D printer; however, seams between
layers spoil them and the quality of printed objects strongly depends
on the slicer.