Abstract: An optimisation method using both global and local
optimisation is implemented to determine the flapping profile which
will produce the most lift for an experimental wing-actuation system.
The optimisation method is tested using a numerical quasi-steady
analysis. Results of an optimised flapping profile show a 20% increase
in lift generated as compared to flapping profiles obtained by high
speed cinematography of a Sympetrum frequens dragonfly. Initial
optimisation procedures showed 3166 objective function evaluations.
The global optimisation parameters - initial sample size and stage
one sample size, were altered to reduce the number of function
evaluations. Altering the stage one sample size had no significant
effect. It was found that reducing the initial sample size to 400
would allow a reduction in computational effort to approximately
1500 function evaluations without compromising the global solvers
ability to locate potential minima. To further reduce the optimisation
effort required, we increase the local solver’s convergence tolerance
criterion. An increase in the tolerance from 0.02N to 0.05N decreased
the number of function evaluations by another 20%. However, this
potentially reduces the maximum obtainable lift by up to 0.025N.
Abstract: Flood routing is used in estimating the travel time and attenuation of flood waves as they move downstream a river or channel. The routing procedure is usually classified as hydrologic or hydraulic. Hydraulic methods utilize the equations of continuity and motion. Kinematic routing, a hydraulic technique was used in routing Asa River at Ilorin. The river is of agricultural and industrial importance to Ilorin, the capital of Kwara State, Nigeria. This paper determines the kinematic parameters of kinematic wave velocity, time step, time required to traverse, weighting factor and change in length. Values obtained were 4.67 m/s, 19 secs, 21 secs, 0.75 and 100 m, respectively. These parameters adequately reflect the watershed and flow characteristics essential for the routing. The synthetic unit hydrograph was developed using the Natural Resources Conservation Service (NRCS) method. 24-hr 10yr, 25yr, 50yr and 100yr storm hydrographs were developed from the unit hydrograph using convolution procedures and the outflow hydrographs were obtained for each of 24-hr 10yr, 25yr, 50yr and 100yr indicating 0.11 m3/s, 0.10 m3/s, 0.10 m3/s and 0.10 m3/s attenuations respectively.
Abstract: A new algorithm based on the lattice Boltzmann method (LBM) is proposed as a potential solver for one-dimensional heat and mass transfer for isothermal carbonization of wood particles. To check the validity of this algorithm, the LBM results have been compared with the published data and a good agreement is obtained. Then, the model is used to study the effect of reactor temperature and particle size on the evolution of the local temperature and mass loss inside the wood particle.
Abstract: This paper proposes a method to automatic transformation of CIM level to PIM level respecting the MDA approach. Our proposal is based on creating a good CIM level through well-defined rules allowing as achieving rich models that contain relevant information to facilitate the task of the transformation to the PIM level. We define, thereafter, an appropriate PIM level through various UML diagram. Next, we propose set rules to move from CIM to PIM. Our method follows the MDA approach by considering the business dimension in the CIM level through the use BPMN, standard modeling business of OMG, and the use of UML in PIM advocated by MDA in this level.
Abstract: Ion exchange is one of the methods used to remove heavy metal such as copper and cobalt from wastewaters. Parameters affecting the ion-exchange of copper and cobalt aqueous solutions using clinoptilolite are the objectives of this study. Synthetic solutions were prepared with the concentration of 0.02M, 0.06M and 0.1M. The cobalt solution was maintained to 0.02M while varying the copper solution to the above stated concentrations. The clinoptilolite was activated with HCl and H2SO4 for removal efficiency. The pHs of the solutions were found to be acidic hence enhancing the copper and cobalt removal. The natural clinoptilolite performance was also found to be lower compared to the HCl and H2SO4 activated one for the copper removal ranging from 68% to 78% of Cu2+ uptake with the natural clinoptilolite to 66% to 51% with HCl and H2SO4 respectively. It was found that the activated clinoptilolite removed more copper and cobalt than the natural one and found that the electronegativity of the metal plays a role in the metal removal and the clinoptilolite selectivity.
Abstract: The research about Formal Thai National Costume in the reign of King Bhumibol Adulyadej is an applied research that aimed to study the accurate knowledge concerning to Thai national costume in the reign of King Rama IX, also to study origin of all costumes in the reign of King Rama IX and to study the style, material used, and using accasion. This research methodology which are collect quanlitative data through observation, document, and photograph from key informant of costume in the reign of King Rama IX and from another who related to this field.
The formal Thai national costume of the reign of King Bhumibol Adulyadej originated from the visit of His Majesty the King to Europe and America in 1960. Since Thailand had no traditional national costume; Her Majesty the Queen initiated the idea to create formal Thai national costumes. In 1964, Her Majesty the Queen selected 8 styles of formal Thai national costume. Later, Her Majesty the Queen confered another 3 formal Thai national costume for men. There are 8 styles of formal Thai national costume for women: Thai Ruean Ton, Thai Chit Lada, Thai Amarin, Thai Borom Phiman, Thai Siwalia, Thai Chakkri, Thai Dusit, and Thai Chakkraphat. There are 3 styles of formal Thai national costume for men: short-sleeve shirt, long-sleeve shirt, and long-sleeve shirt with breechcloth. The costume is widely used in formal ceremony such as greeting ceremony for official foreign visitors, wedding ceremony, or other auspicious ceremonies. Now a day, they are always used as a bridal gown as well. The formal Thai national costume is valuable art that shows Thai identity and, should be preserved for the next generation.
Abstract: When it comes to last, it is regarded as the critical foundation of shoe design and development. Not only the last relates to the comfort of shoes wearing but also it aids the production of shoe styling and manufacturing. In order to enhance the efficiency and application of last development, a computer aided methodology for customized last form designs is proposed in this study. The reverse engineering is mainly applied to the process of scanning for the last form. Then the minimum energy is used for the revision of surface continuity, the surface of the last is reconstructed with the feature curves of the scanned last. When the surface of a last is reconstructed, based on the foundation of the proposed last form reconstruction module, the weighted arithmetic mean method is applied to the calculation on the shape morphing which differs from the grading for the control mesh of last, and the algorithm of subdivision is used to create the surface of last mesh, thus the feet-fitting 3D last form of different sizes is generated from its original form feature with functions remained. Finally, the practicability of the proposed methodology is verified through later case studies.
Abstract: The most important problem occurs on oil spills in sea
water is to reduce the oil spills size. This study deals with the
development of high pressurized nozzle using dispersion method for
oil leakage in offshore. 3D numerical simulation results were
obtained using ANSYS Fluent 13.0 code and correlate with the
experimental data for validation. This paper studies the contribution
of the process on flow speed and pressure of the flow from two
different geometrical designs of nozzles and to generate a spray
pattern suitable for dispersant application. Factor of size distribution
of droplets generated by the nozzle is calculated using pressures
ranging from 2 to 6 bars. Results obtain from both analyses shows a
significant spray pattern and flow distribution as well as distance.
Results also show a significant contribution on the effect of oil
leakage in terms of the diameter of the oil spills break up.
Abstract: Heat transfer from flat tube is studied numerically. Reynolds number is defined base on equivalent circular tube which is varied in range of 100 to 300. In these range of Reynolds number flow is considered to be laminar, unsteady, and incompressible. Equations are solved by using finite volume method. Results show that increasing l/D from 1 to 2 has insignificant effect on heat transfer and Nusselt number of flat tube is slightly lower than circular tube. However, thermal-hydraulic performance of flat tube is up to 2.7 times greater than circular tube.
Abstract: The effect of tillage technology of maize on intensity of weed infestation and weed species composition was observed at experimental field. Maize is grown consecutively since 2001. The experimental site is situated at an altitude of 230 m above sea level in the Czech Republic. Variants of tillage technology are CT: plowing – conventional tillage 0.22 m, MT: loosening – disc tillage on the depth of 0.1 – 0.12 m, NT: direct sowing – without tillage. The evaluation of weed infestation was carried out by numerical method in years 2012 and 2013. Within the monitoring were found 20 various species of weeds. Conventional tillage (CT) primarily supports the occurrence of perennial weeds (Cirsium arvense, Convolvulus arvensis). Late spring species (Chenopodium album, Echinochloa crus-galli) were more frequently noticed on variants of loosening (MT) and direct sowing (NT). Different tillage causes a significant change of weed species spectrum in maize.
Abstract: Chaotic analysis has been performed on the river flow time series before and after applying the wavelet based de-noising techniques in order to investigate the noise content effects on chaotic nature of flow series. In this study, 38 years of monthly runoff data of three gauging stations were used. Gauging stations were located in Ghar-e-Aghaj river basin, Fars province, Iran. Noise level of time series was estimated with the aid of Gaussian kernel algorithm. This step was found to be crucial in preventing removal of the vital data such as memory, correlation and trend from the time series in addition to the noise during de-noising process.
Abstract: Vertical slotted walls can be used as permeable
breakwaters to provide economical and environmental protection
from undesirable waves and currents inside the port. The permeable
breakwaters are partially protection and have been suggested to
overcome the environmental disadvantages of fully protection
breakwaters. For regular waves a semi-analytical model is based on
an eigenfunction expansion method and utilizes a boundary condition
at the surface of each wall are developed to detect the energy
dissipation through the slots. Extensive laboratory tests are carried
out to validate the semi-analytic models. The structure of the physical
model contains two walls and it consists of impermeable upper and
lower part, where the draft is based a decimal multiple of the total
depth. The middle part is permeable with a porosity of 50%. The
second barrier is located at a distant of 0.5, 1, 1.5 and 2 times of the
water depth from the first one. A comparison of the theoretical results
with previous studies and experimental measurements of the present
study show a good agreement and that, the semi-analytical model is
able to adequately reproduce most the important features of the
experiment.
Abstract: Recently there has been a dramatic proliferation in
the number of social networking sites (SNSs) users; however, little
is published about what motivates college students to use SNSs in
education. The main goal of this research is to explore the college
students’ motives for using SNSs in education. A conceptual
framework has therefore been developed to identify the main
factors that influence/motivate students to use social networking
sites for learning purposes. To achieve the research objectives a
quantitative method was used to collect data. A questionnaire has
been distributed amongst college students. The results reveal that
social influence, perceived enjoyment, institute regulation,
perceived usefulness, ranking up-lift, attractiveness,
communication tools, free of charge, sharing material and course
nature all play an important role in the motivation of college
students to use SNSs for learning purposes.
Abstract: Advances in the field of image processing envision a
new era of evaluation techniques and application of procedures in
various different fields. One such field being considered is the
biomedical field for prognosis as well as diagnosis of diseases. This
plethora of methods though provides a wide range of options to select
from, it also proves confusion in selecting the apt process and also in
finding which one is more suitable. Our objective is to use a series of
techniques on bone scans, so as to detect the occurrence of
rheumatoid arthritis (RA) as accurately as possible. Amongst other
techniques existing in the field our proposed system tends to be more
effective as it depends on new methodologies that have been proved
to be better and more consistent than others. Computer aided
diagnosis will provide more accurate and infallible rate of
consistency that will help to improve the efficiency of the system.
The image first undergoes histogram smoothing and specification,
morphing operation, boundary detection by edge following algorithm
and finally image subtraction to determine the presence of
rheumatoid arthritis in a more efficient and effective way. Using preprocessing
noises are removed from images and using segmentation,
region of interest is found and Histogram smoothing is applied for a
specific portion of the images. Gray level co-occurrence matrix
(GLCM) features like Mean, Median, Energy, Correlation, Bone
Mineral Density (BMD) and etc. After finding all the features it
stores in the database. This dataset is trained with inflamed and noninflamed
values and with the help of neural network all the new
images are checked properly for their status and Rough set is
implemented for further reduction.
Abstract: The high efficiency power management IC (PMIC) with switching device is presented in this paper. PMIC is controlled with PFM control method in order to have high power efficiency at high current level. Dynamic Threshold voltage CMOS (DT-CMOS) with low on-resistance is designed to decrease conduction loss. The threshold voltage of DT-CMOS drops as the gate voltage increase, resulting in a much higher current handling capability than standard MOSFET. PFM control circuits consist of a generator, AND gate and comparator. The generator is made to have 1.2MHz oscillation voltage. The DC-DC converter based on PFM control circuit and low on-resistance switching device is presented in this paper.
Abstract: This paper deals with a proposal of a new
methodology for durability assessment of solidification product for
its safe further use. The new methodology is based on a review of the
current state of assessment of treated waste in Czech Republic and
abroad. The aim of the paper is to propose an optimal evaluation
methodology for verifying properties of solidification product to
ensure its safe further use in building industry.
Abstract: The purpose of this study is to identify the teaching method practices of the practical work subject in Vocational Secondary School. This study examined the practice of Vocational Teaching Method in Automotive Practical Work. The quantitative method used the sets of the questionnaire. 283 students and 63 teachers involved from ten VSS involved in this research. Research finding showed in conducting the introduction session teachers prefer used the demonstration method and questioning technique. While in deliver the content of practical task, teachers applied group monitoring and problem solving approach. To conclude the task of automotive practical work, teachers choose re-explain and report writing to make sure students really understand all the process of teaching. VTM-APW also involved the competency-based concept to embed in the model. Derived from factors investigated, research produced the combination of elements in teaching skills and vocational skills which could be used as the best teaching method in automotive practical work for school level. As conclusion this study has concluded that the VTM-APW model is able to apply in teaching to make an improvement with current practices in Vocational Secondary School. Hence, teachers are suggested to use this method to enhance student's knowledge in Automotive and teachers will deliver skills to the current and future workforce relevant with the required competency skilled in workplace.
Abstract: For Common R or R-L load to apply arbitrary voltage,
the bridge traditional inverters don’t have any difficulties by PWM
method. However for driving some piezoelectric actuator, arbitrary
voltage not a pulse but a steady voltage should be applied.
Piezoelectric load is considered as R-C load and its voltage does not
decrease even though the applied voltage decreases. Therefore it needs
some special inverter with circuit that can discharge the capacitive
energy. Especially for unidirectional arbitrary voltage driving like as
sine wave, it becomes more difficult problem. In this paper, a charge
and discharge circuit for unidirectional arbitrary voltage driving for
piezoelectric actuator is proposed. The circuit has charging and
discharging switches for increasing and decreasing output voltage.
With the proposed simple circuit, the load voltage can have any
unidirectional level with tens of bandwidth because the load voltage
can be adjusted by switching the charging and discharging switch
appropriately. The appropriateness is proved from the simulation of
the proposed circuit.
Abstract: In a human tracking system, expanding a monitoring
range of one system is complicating the management of devices and
increasing its cost. Therefore, we propose a method to realize a
wide-range human tracking by connecting small systems. In this paper,
we examined an agent deploy method and information contents across
the heterogeneous human tracking systems. By implementing the
proposed method, we can construct a human tracking system across
heterogeneous systems, and the system can track a target continuously
between systems.
Abstract: In this paper, we propose a method that allows faster and more accurate detection of traffic lights by a vision sensor during driving, DGPS is used to obtain physical location of a traffic light, extract from the image information of the vision sensor only the traffic light area at this location and ascertain if the sign is in operation and determine its form. This method can solve the problem in existing research where low visibility at night or reflection under bright light makes it difficult to recognize the form of traffic light, thus making driving unstable. We compared our success rate of traffic light recognition in day and night road environments. Compared to previous researches, it showed similar performance during the day but 50% improvement at night.