Abstract: Equal channel angular pressing (ECAP) of
commercial Al-Mg-Si alloy was conducted using two strain rates.
The ECAP processing was conducted at room temperature and at
250°C. Route A was adopted up to a total number of four passes in
the present work. Structural evolution of the aluminum alloy discs
was investigated before and after ECAP processing using optical
microscopy (OM). Following ECAP, simple compression tests and
Vicker’s hardness were performed. OM micrographs showed that, the
average grain size of the as-received Al-Mg-Si disc tends to be larger
than the size of the ECAP processed discs. Moreover, significant
difference in the grain morphologies of the as-received and processed
discs was observed. Intensity of deformation was observed via the
alignment of the Al-Mg-Si consolidated particles (grains) in the
direction of shear, which increased with increasing the number of
passes via ECAP. Increasing the number of passes up to 4 resulted in
increasing the grains aspect ratio up to ~5. It was found that the
pressing temperature has a significant influence on the
microstructure, Hv-values, and compressive strength of the processed
discs. Hardness measurements demonstrated that 1-pass resulted in
increase of Hv-value by 42% compared to that of the as-received
alloy. 4-passes of ECAP processing resulted in additional increase in
the Hv-value. A similar trend was observed for the yield and
compressive strength. Experimental data of the Hv-values
demonstrated that there is a lack of any significant dependence on the
processing strain rate.
Abstract: As the current status and growth of Indian automobile
industry is remarkable, transportation sectors are the main concern in
terms of energy security and climate change. Due to rising demand of
fuel and its dependency on foreign countries that affects the GDP of
nation, suggests that penetration of electrical vehicle will increase in
near future. So in this context analysis is done if the 10 percent of
conventional vehicles including cars, three wheelers and two
wheelers becomes electrical vehicles in near future which is also a
part of Nations Electric Mobility Mission Plan then the saving which
improves the nation’s economy is analyzed in detail. Whether the
Indian electricity grid is capable of taking this load with current
generation and demand all over the country is also analyzed in detail.
Current situation of Indian grid is analyzed and how the gap between
generation and demand can be reduced is discussed in terms of
increasing generation capacity and energy conservation measures.
Electrical energy conservation measures in Industry and especially in
rural areas have been analyzed to improve performance of Indian
electricity grid in context of electrical vehicle penetration in near
future. Author was a part of Vishvakarma yojna in which energy
losses were measured in 255 villages of Gujarat and solutions were
suggested to mitigate them and corresponding reports was submitted
to the authorities of Gujarat government.
Abstract: The aim of this work was to apply extractive
distillation for acetonitrile removal from water solutions, to validate
thermodynamic criterion based on excess Gibbs energy to entrainer
selection process for acetonitrile – water mixture separation and show
its potential efficiency at isothermal conditions as well as at isobaric
(conditions of real distillation process), to simulate and analyze an
extractive distillation process with chosen entrainers: optimize
amount of trays and feeds, entrainer/original mixture and reflux
ratios. Equimolar composition of the feed stream was chosen for the
process, comparison of the energy consumptions was carried out.
Glycerol was suggested as the most energetically and ecologically
suitable entrainer.
Abstract: Pipe failure and leakage is a problematic issue and the
traditional solution of replacing the pipes is costly and time
consuming. Rehabilitation by relining materials based on polymer
composites is an alternative solution towards the degradation problem
of the old piping. This paper provides a brief summary of advances in
technology, methods and materials for relining as well as a summary
of the degradation analyses of the two main composite materials used
for relining, rubber filled epoxy and reinforced polyester baltoflake
when they are exposed in deionized water and elevated temperature
up to 80°C for a duration of 2-14 months in the laboratory.
Abstract: Laser beam welding of dissimilar sheet metal
combinations such as Ti/Al, SS/Al and Cu/Al are increasingly
demanded due to high energy densities with less fusion and heat
affected zones. A good weld joint strength involves combinations of
dissimilar metals and the formation of solid solution in the weld pool.
Many metal pairs suffer from significant intermetallic phase
formation during welding which greatly reduces their strength. The
three different sheet metal mentioned above is critically reviewed and
phase diagram for the combinations are given. The aim of this study
is to develop an efficient metal combinations and the influence on
their interfacial characteristics. For that the following parameters
such as weld geometry, residual distortion, micro hardness,
microstructure and mechanical properties are analyzed
systematically.
Abstract: The contact resistance between source/drain electrodes
and semiconductor layer is an important parameter affecting electron
transporting performance in the thin film transistor (TFT). In this
work, we introduced a transparent and the solution prossable
single-walled carbon nanotube (SWCNT)/Al-doped ZnO nano particle
(AZO NP) bilayer electrodes showing low contact resistance with
indium-oxide (In2O3) sol gel thin film. By inserting low work function
AZO NPs into the interface between the SWCNTs and the In2O3 which
has a high energy barrier, we could obtain an electrical Ohmic contact
between them. Finally, with the SWCNT-AZO NP bilayer electrodes,
we successfully fabricated a TFT showing a field effect mobility of
5.38 cm2/V·s at 250°C.
Abstract: Contracting authorities in the public sector are
obligated to apply the principles provided for in the Polish law for the
evaluation and selection of contractors. In order to analyse the
methods of contractors selecting applied in practice by public clients,
the notices of contract award results for construction works were
analysed. The analysis shows that the procedure selected more and
more often is open competitive bidding, where the assessment of the
competence of contractors is not very precise, as well as noncompetitive
bidding, i.e. single source procurement. The share of
procurement procedures, where the only criterion is price, is
increasing. The solution to the problems existing here might be the
introduction of one of the forms of pre-selection of contractors. The
article also briefly discusses verification systems for companies
applying for public contracts used in EU countries.
Abstract: Food is widely packaged with plastic materials to
prevent microbial contamination and spoilage. Ionizing radiation is
widely used to sterilize the food-packaging materials. Sterilization by
γ-radiation causes degradation such as embrittlement, stiffening,
softening, discoloration, odour generation, and decrease in molecular
weight. Many antioxidants can prevent γ-degradation but most of
them are toxic. The migration of antioxidants to its environment
gives rise to major concerns in case of food packaging plastics. In
this attempt, we have aimed to utilize synergistic mixtures of
stabilizers which are approved for food-contact applications.
Ethylene-propylene-diene terpolymer has been melt-mixed with
hindered amine stabilizers (HAS), phenolic antioxidants and organophosphites
(hydroperoxide decomposer). Results were discussed by
comparing the stabilizing efficiency of mixtures with and without
phenol system. Among phenol containing systems where we mostly
observed discoloration due to the oxidation of hindered phenol, the
combination of secondary HAS, tertiary HAS, organo-phosphite and
hindered phenol exhibited improved stabilization efficiency than
single or binary additive systems. The mixture of secondary HAS and
tertiary HAS, has shown antagonistic effect of stabilization.
However, the combination of organo-phosphite with secondary HAS,
tertiary HAS and phenol antioxidants have been found to give
synergistic even at higher doses of Gamma-irradiation. The effects
have been explained through the interaction between the stabilizers.
After γ-irradiation, the consumption of oligomeric stabilizer
significantly depends on the components of stabilization mixture. The
effect of the organo-phosphite antioxidant on the overall stability has
been discussed.
Abstract: Rotary draw bending is a method which is being used
in tube forming. In the tube bending process, the neutral axis moves
towards the inner arc and the wall thickness distribution changes for
tube’s cross section. Thinning takes place in the outer arc of the tube
(extrados) due to the stretching of the material, whereas thickening
occurs in the inner arc of the tube (intrados) due to the comparison of
the material. The calculations of the wall thickness distribution,
neutral axis shifting, and strain distribution have not been accurate
enough, so far. The previous model (the geometrical model)
describes the neutral axis shifting and wall thickness distribution. The
geometrical of the tube, bending radius and bending angle are
considered in the geometrical model, while the influence of the
material properties of the tube forming are ignored. The advanced
model is a modification of the previous model using material
properties that depends on the correction factor. The correction factor
is a purely empirically determined factor. The advanced model was
compared with the Finite element simulation (FE simulation) using a
different bending factor (Bf =bending radius/ diameter of the tube),
wall thickness (Wf = diameter of the tube/ wall thickness), and
material properties (strain hardening exponent). Finite element model
of rotary draw bending has been performed in PAM-TUBE program
(version: 2012). Results from the advanced model resemble the FE
simulation and the experimental test.
Abstract: The effect of the inclusion of thyme and rosemary
essential oils into chitosan films, as well as the microbiological and
physical properties when storing chitosan film with and without the
mentioned inclusion was studied. The film forming solution was
prepared by dissolving chitosan (2%, w/v), polysorbate 80 (4% w/w
CH) and glycerol (16% w/w CH) in aqueous lactic acid solutions
(control). The thyme (TEO) and rosemary (REO) essential oils (EOs)
were included 1:1 w/w (EOs:CH) on their combination 50/50
(TEO:REO). The films were stored at temperatures of 5, 20, 33°C
and a relative humidity of 75% during four weeks. The films with
essential oil inclusion did not show an antimicrobial activity against
strains. This behavior could be explained because the chitosan only
inhibits the growth of microorganisms in direct contact with the
active sites. However, the inhibition capacity of TEO was higher than
the REO and a synergic effect between TEO:REO was found for S.
enteritidis strains in the chitosan solution.
Some physical properties were modified by the inclusion of
essential oils. The addition of essential oils does not affect the
mechanical properties (tensile strength, elongation at break, puncture
deformation), the water solubility, the swelling index nor the DSC
behavior. However, the essential oil inclusion can significantly
decrease the thickness, the moisture content, and the L* value of
films whereas the b* value increased due to molecular interactions
between the polymeric matrix, the loosing of the structure, and the
chemical modifications. On the other hand, the temperature and time
of storage changed some physical properties on the chitosan films.
This could have occurred because of chemical changes, such as
swelling in the presence of high humidity air and the reacetylation of
amino groups. In the majority of cases, properties such as moisture
content, tensile strength, elongation at break, puncture deformation,
a*, b*, chrome, 7E increased whereas water resistance, swelling
index, L*, and hue angle decreased.
Abstract: Chemical Reaction Optimization (CRO) is an
optimization metaheuristic inspired by the nature of chemical
reactions as a natural process of transforming the substances from
unstable to stable states. Starting with some unstable molecules with
excessive energy, a sequence of interactions takes the set to a state of
minimum energy. Researchers reported successful application of the
algorithm in solving some engineering problems, like the quadratic
assignment problem, with superior performance when compared with
other optimization algorithms. We adapted this optimization
algorithm to the Printed Circuit Board Drilling Problem (PCBDP)
towards reducing the drilling time and hence improving the PCB
manufacturing throughput. Although the PCBDP can be viewed as
instance of the popular Traveling Salesman Problem (TSP), it has
some characteristics that would require special attention to the
transactions that explore the solution landscape. Experimental test
results using the standard CROToolBox are not promising for
practically sized problems, while it could find optimal solutions for
artificial problems and small benchmarks as a proof of concept.
Abstract: A Silver (Ag) thin film is introduced as a template and
doping source for vertically aligned p–type ZnO nanorods. ZnO
nanorods were grown using an ammonium hydroxide based
hydrothermal process. During the hydrothermal process, the Ag thin
film was dissolved to generate Ag ions in the solution. The Ag ions can
contribute to doping in the wurzite structure of ZnO and the (111)
grain of Ag thin film can be the epitaxial temporal template for the
(0001) plane of ZnO. Hence, Ag–doped p–type ZnO nanorods were
successfully grown on the substrate, which can be an electrode or
semiconductor for the device application. To demonstrate the
potentials of this idea, p–n diode was fabricated and its electrical
characteristics were demonstrated.
Abstract: The transition period of Kosovo society brought
fundamental changes in all the spheres of organizing life. This was
the period when also in the cultural tradition the biggest movement
and an emerging from ‘isolation’ or from the ‘shell’ occurred.
Transformation of the traditional and embracing of the modern began
here. The same was experienced and is currently being experienced
also by Gjakova and its surrounding which is historically renowned
for its great tradition and culture.
The population of this region is actually facing a transition from
the traditional system into the modern one and quite often with huge
leaps.
These ‘movements’ or ‘evolutions’ of the society of this region,
besides the numerous positive things it ‘harvested’, also brought
things that do not at all correspond with their tradition as well as new
criminal occurrences which in the past were not present in this area.
Furthermore, some of the ‘new’ behaviors that are embraced from
other ‘cultures’ and ‘civilizations’, and which are often exceeded, are
quite perturbing. The security situation is also worrying, particularly
following the appearance of some new criminal occurrences.
Therefore, with this research paper we will strive to analyze the
new cultural “intersections” as well as the nature of the origin of
some new very worrying criminal occurrences. We will present there
also some factors inciting into these occurrences, which were
confessed by the persons involved in these criminal occurrences and
who come from this very region.
Abstract: Fugitive particulate matter (PM) is a major source of
airborne pollution in the Middle East countries. The meteorological
conditions and topography of the area makes it highly susceptible to
wind-blown particles which raise many air quality concerns. Air
quality tools such as field monitoring, emission factors and dispersion
modeling have been used in previous research studies to analyze the
release and impacts of fugitive PM in the region. However, these
tools have been originally developed based on experiments made for
European and North American regions. In this work, an experimental
campaign was conducted on April-May 2014 in a construction site in
Doha city, Qatar. The ultimate goal is to evaluate the applicability of
the existing emission factors for construction sites in dry and arid
areas like the Middle East.
Abstract: We present a solution to the Maxmin u/E parameters
estimation problem of possibility distributions in m-dimensional
case. Our method is based on geometrical approach, where minimal
area enclosing ellipsoid is constructed around the sample. Also we
demonstrate that one can improve results of well-known algorithms
in fuzzy model identification task using Maxmin u/E parameters
estimation.
Abstract: Welfare may be considered to be a subjective
experience; it has a biological function that is related to the fitness
and survival of the animal accordingly, researches have suggested
that welfare is compromised when the animal's evolutionary fitness is
reduced. This study was carried out to explain the effect of some
managerial stressors as handling and restraint on behavioral patterns
and biochemical parameters of rats. A total of 24 (12 males & 12
females) Sprague-Dawley rats (12 months & 150-180g) were allotted
into 3 groups, handled group (4 male & 4 female), restrained group (4
male & 4 female) and control group (4 males & 4 females).
The obtained results revealed that time spent feeding, drinking,
movement and cage exploration frequencies increased significantly in
handled rats than other groups, while lying time and licking increased
significantly in restrained rats than handled and controls. Moreover,
social behavior decreased in both stressed groups than control.
Triglycerides were significantly increased in handled rats than
other groups, while total lipid, total protein and globulin significantly
increased in both treated groups than control. Corticosterone
increased in restrained and handled rats than control ones. Moreover,
there was an increment in packed cell volume significantly in
restrained rats than others. These deducted that if we want to study
the effect of stress on animal welfare it is necessary to study the
effect of such stressors on animal’s behavior and physiological
responses.
Abstract: This paper focuses on the assessment of the air
pollution and morbidity relationship in Tunisia. Air pollution is
measured by ozone air concentration and the morbidity is measured
by the number of respiratory-related restricted activity days during
the 2-week period prior to the interview. Socioeconomic data are also
collected in order to adjust for any confounding covariates. Our
sample is composed by 407 Tunisian respondents; 44.7% are women,
the average age is 35.2, near 69% are living in a house built after
1980, and 27.8% have reported at least one day of respiratory-related
restricted activity. The model consists on the regression of the
number of respiratory-related restricted activity days on the air
quality measure and the socioeconomic covariates. In order to correct
for zero-inflation and heterogeneity, we estimate several models
(Poisson, negative binomial, zero inflated Poisson, Poisson hurdle,
negative binomial hurdle and finite mixture Poisson models).
Bootstrapping and post-stratification techniques are used in order to
correct for any sample bias. According to the Akaike information
criteria, the hurdle negative binomial model has the greatest goodness
of fit. The main result indicates that, after adjusting for
socioeconomic data, the ozone concentration increases the probability
of positive number of restricted activity days.
Abstract: In this paper, a system of linear matrix equations
is considered. A new necessary and sufficient condition for the
consistency of the equations is derived by means of the generalized
singular-value decomposition, and the explicit representation of the
general solution is provided.
Abstract: Given the dynamic nature of the higher education
landscape, induction programmes for new academics has become the
norm nowadays to support academics negotiate these rough terrain.
This study investigates an induction programme for new academics
in a higher education institution to establish what difference it has
made to participants. The findings revealed that the benefits ranged
from creating safe spaces for collaboration and networking to
fostering reflective practice and contributing to the scholarship of
teaching and learning. The study also revealed that some of the
intentions of the programme may not have been achieved, for
example transformative learning. This led to questioning whether this
intention is an appropriate one given the short duration of the
programme and the long, drawn out process of transformation. It may
be concluded that the academic induction programme in this study
serves to sow the seeds for transformative learning through fostering
critically reflective practice. Recommendations for further study
could include long term impact of the programme on student learning
and success, these being the core business of higher education. It is
also recommended that in addition to an induction programme, the
university invests in a mentoring programme for new staff and extend
the support for academics in order to sustain critical reflection and
which may contribute to transformative educational practice.
Abstract: A strain of Monascus purpureus CMU001 was used to
prepare red yeast rice from Thai glutinous rice Korkor 6 (RD 6).
Adding of different amounts of histidine (156, 312, 625 and 1250 mg
in 100 g of rice grains)) under aerobic and air limitation (air-lock)
condition were used in solid fermentation. Determination of the yield
as well as monacolin K content was done. Citrinin content was also
determined in order to confirm the safety use of prepared red yeast
rice. It was found that under air-lock condition with 1250 mg of
histidine addition gave the highest yield of 37.40 g of dried red yeast
rice prepared from 100 g of rice. Highest 5.72 mg content of
monacolin K was obtained under air-lock condition with 312 mg
histidine addition. In the other hand, citrinin content was found to be
less than 24462 ng/g of all dried red yeast rice samples under the
experimental methods used in this work.