Abstract: The results from experimental research of deformation
by upsetting and die forging of lead specimens wit controlled impact
are presented. Laboratory setup for conducting the investigations,
which uses cold rocket engine operated with compressed air, is
described. The results show that when using controlled impact is
achieving greater plastic deformation and consumes less impact
energy than at ordinary impact deformation process.
Abstract: The simulation of extrusion process is studied widely
in order to both increase products and improve quality, with broad
application in wire coating. The annular tube-tooling extrusion was
set up by a model that is termed as Navier-Stokes equation in
addition to a rheological model of differential form based on singlemode
exponential Phan-Thien/Tanner constitutive equation in a twodimensional
cylindrical coordinate system for predicting the
contraction point of the polymer melt beyond the die. Numerical
solutions are sought through semi-implicit Taylor-Galerkin pressurecorrection
finite element scheme. The investigation was focused on
incompressible creeping flow with long relaxation time in terms of
Weissenberg numbers up to 200. The isothermal case was considered
with surface tension effect on free surface in extrudate flow and no
slip at die wall. The Stream Line Upwind Petrov-Galerkin has been
proposed to stabilize solution. The structure of mesh after die exit
was adjusted following prediction of both top and bottom free
surfaces so as to keep the location of contraction point around one
unit length which is close to experimental results. The simulation of
extrusion process is studied widely in order to both increase products
and improve quality, with broad application in wire coating. The
annular tube-tooling extrusion was set up by a model that is termed
as Navier-Stokes equation in addition to a rheological model of
differential form based on single-mode exponential Phan-
Thien/Tanner constitutive equation in a two-dimensional cylindrical
coordinate system for predicting the contraction point of the polymer
melt beyond the die. Numerical solutions are sought through semiimplicit
Taylor-Galerkin pressure-correction finite element scheme.
The investigation was focused on incompressible creeping flow with
long relaxation time in terms of Weissenberg numbers up to 200. The
isothermal case was considered with surface tension effect on free
surface in extrudate flow and no slip at die wall. The Stream Line
Upwind Petrov-Galerkin has been proposed to stabilize solution. The
structure of mesh after die exit was adjusted following prediction of
both top and bottom free surfaces so as to keep the location of
contraction point around one unit length which is close to
experimental results.
Abstract: Proteins or genes that have similar sequences are likely to perform the same function. One of the most widely used techniques for sequence comparison is sequence alignment. Sequence alignment allows mismatches and insertion/deletion, which represents biological mutations. Sequence alignment is usually performed only on two sequences. Multiple sequence alignment, is a natural extension of two-sequence alignment. In multiple sequence alignment, the emphasis is to find optimal alignment for a group of sequences. Several applicable techniques were observed in this research, from traditional method such as dynamic programming to the extend of widely used stochastic optimization method such as Genetic Algorithms (GAs) and Simulated Annealing. A framework with combination of Genetic Algorithm and Simulated Annealing is presented to solve Multiple Sequence Alignment problem. The Genetic Algorithm phase will try to find new region of solution while Simulated Annealing can be considered as an alignment improver for any near optimal solution produced by GAs.
Abstract: This paper studies the optimum design for reducing
optical loss of an 8x8 mechanical type optical switch due to the
temperature change. The 8x8 optical switch is composed of a base, 8
input fibers, 8 output fibers, 3 fixed mirrors and 17 movable mirrors.
First, an innovative switch configuration is proposed with
thermal-compensated design. Most mechanical type optical switches
have a disadvantage that their precision and accuracy are influenced
by the ambient temperature. Therefore, the thermal-compensated
design is to deal with this situation by using materials with different
thermal expansion coefficients (α). Second, a parametric modeling
program is developed to generate solid models for finite element
analysis, and the thermal and structural behaviors of the switch are
analyzed. Finally, an integrated optimum design program, combining
Autodesk Inventor Professional software, finite element analysis
software, and genetic algorithms, is developed for improving the
thermal behaviors that the optical loss of the switch is reduced. By
changing design parameters of the switch in the integrated design
program, the final optimum design that satisfies the design constraints
and specifications can be found.
Abstract: Place is a where dimension formed by people-s
relationship with physical settings, individual and group activities,
and meanings. 'Place Attachment', 'Place Identity'and 'Sense of
Place' are some concepts that could describe the quality of people-s
relationships with a place. The concept of Sense of place is used in
studying human-place bonding, attachment and place meaning. Sense
of Place usually is defined as an overarching impression
encompassing the general ways in which people feel about places,
senses it, and assign concepts and values to it. Sense of place is
highlighted in this article as one of the prevailing concepts among
place-based researches. Considering dimensions of sense of place has
always been beneficial for investigating public place attachment and
pro-environmental attitudes towards these places. The creation or
preservation of Sense of place is important in maintaining the quality
of the environment as well as the integrity of human life within it.
While many scholars argued that sense of place is a vague concept,
this paper will summarize and analyze the existing seminal literature.
Therefore, in this paper first the concept of Sense of place and its
characteristics will be examined afterward the scales of Sense of
place will be reviewed and the factors that contribute to form Sense
of place will be evaluated and finally Place Attachment as an
objective dimension for measuring the sense of place will be
described.
Abstract: A new fast correlation algorithm for calibrating the
wavelength of Optical Spectrum Analyzers (OSAs) was introduced
in [1]. The minima of acetylene gas spectra were measured and
correlated with saved theoretical data [2]. So it is possible to find the
correct wavelength calibration data using a noisy reference spectrum.
First tests showed good algorithmic performance for gas line spectra
with high noise. In this article extensive performance tests were made
to validate the noise resistance of this algorithm. The filter and
correlation parameters of the algorithm were optimized for improved
noise performance. With these parameters the performance of this
wavelength calibration was simulated to predict the resulting
wavelength error in real OSA systems. Long term simulations were
made to evaluate the performance of the algorithm over the lifetime
of a real OSA.
Abstract: The purpose of this paper is to guide the effort in
improving the economic added value of Indonesian fisheries product
through post fishing program, which is cold storage program.
Indonesia's fisheries potential has been acknowledged by the world.
FAO (2009) stated that Indonesia is one of the tenth highest
producers of fishery products in the world. Based on BPS (Statistics
Indonesia data), the national fisheries production in 2011 reached
5.714 million tons, which 93.55% came from marine fisheries and
6.45% from open waters. Indonesian territory consist of 2/3 of
Indonesian waters, has given enormous benefits for Indonesia,
especially fishermen. To improve the economic level of fishermen
requires efforts to develop fisheries business unit. On of the efforts is
by improving the quality of products which are marketed in the
regional and international levels. It is certainly need the support of
the existence of various fishery facilities (infrastructure to
superstructure), one of which is cold storage. Given the many
benefits of cold storage as a means of processing of fishery resources,
Indonesia Maritime Security Coordinating Board (IMSCB) as one of
the maritime institutions for maritime security and safety, has a
program to empower the coastal community through encourages the
development of cold storage in the middle and lower fishery business
unit. The development of cold storage facilities which able to run its
maximum role requires synergistic efforts of various parties.
Abstract: The equations governing the flow of an electrically conducting, incompressible viscous fluid over an infinite flat plate in the presence of a magnetic field are investigated using the homotopy perturbation method (HPM) with Padé approximants (PA) and 4th order Runge–Kutta method (4RKM). Approximate analytical and numerical solutions for the velocity field and heat transfer are obtained and compared with each other, showing excellent agreement. The effects of the magnetic parameter and Prandtl number on velocity field, shear stress, temperature and heat transfer are discussed as well.
Abstract: This paper addresses the design of predictive
networked controller with adaptation of a communication delay. The
networked control system contains random delays from sensor to
controller and from controller to actuator. The proposed predictive
controller includes an adaptation loop which decreases the influence
of communication delay on the control performance. Also, the
predictive controller contains a filter which improves the robustness
of the control system. The performance of the proposed adaptive
predictive controller is demonstrated by simulation results in
comparison with PI controller and predictive controller with constant
delay.
Abstract: Diabetes Mellitus is a chronic metabolic disorder, where the improper management of the blood glucose level in the diabetic patients will lead to the risk of heart attack, kidney disease and renal failure. This paper attempts to enhance the diagnostic accuracy of the advancing blood glucose levels of the diabetic patients, by combining principal component analysis and wavelet neural network. The proposed system makes separate blood glucose prediction in the morning, afternoon, evening and night intervals, using dataset from one patient covering a period of 77 days. Comparisons of the diagnostic accuracy with other neural network models, which use the same dataset are made. The comparison results showed overall improved accuracy, which indicates the effectiveness of this proposed system.
Abstract: When the characteristic length of an elastic solid is
down to the nanometer level, its deformation behavior becomes size
dependent. Surface energy /surface stress have recently been applied
to explain such dependency. In this paper, the effect of
strain-independent surface stress on the deformation of an isotropic
elastic solid containing a nanosized elliptical hole is studied by the
finite element method. Two loading cases are considered, in the first
case, hoop stress along the rim of the elliptical hole induced by pure
surface stress is studied, in the second case, hoop stress around the
elliptical opening under combined remote tension and surface stress is
investigated. It has been shown that positive surface stress induces
compressive hoop stress along the hole, and negative surface stress has
opposite effect, maximum hoop stress occurs near the major semi-axes
of the ellipse. Under combined loading of remote tension and surface
stress, stress concentration around the hole can be either intensified or
weakened depending on the sign of the surface stress.
Abstract: This work deals with aspects of support vector learning for large-scale data mining tasks. Based on a decomposition algorithm that can be run in serial and parallel mode we introduce a data transformation that allows for the usage of an expensive generalized kernel without additional costs. In order to speed up the decomposition algorithm we analyze the problem of working set selection for large data sets and analyze the influence of the working set sizes onto the scalability of the parallel decomposition scheme. Our modifications and settings lead to improvement of support vector learning performance and thus allow using extensive parameter search methods to optimize classification accuracy.
Abstract: Bologna process has influenced enhancing studentcentered
learning in Estonian higher education since 2009, but there
is no information about what helps or hinders students to achieve
learning outcomes and how quality of student-centered learning
might be improved. The purpose of this study is to analyze two
questions from outcome-based course evaluation questionnaire which
is used in Estonian Entrepreneurship University of Applied Sciences.
In this qualitative research, 384 students from 22 different courses
described what helped and hindered them to achieve learning
outcomes. The analysis showed that the aspects that hinder students
to achieve learning outcomes are mostly personal: time management,
family and personal matters, motivation and non-academic activities.
The results indicate that students- learning is commonly supported by
school, where teacher, teaching and characteristics of teaching
methods help mostly to achieve learning outcomes, also learning
material, practical assignments and independent study was brought
up as one of the key elements.
Abstract: The impeller and the casing are the key components of
a centrifugal pump. Although there have been many studies on the
impeller and the volute casing of centrifugal pump, further study of the
volute casing to improve the performance of centrifugal pumps is
needed. In this paper, the effect of cross-sectional area on the
performance of volute casing was investigated using a commercial
CFD code. The performance characteristics, not only at the off-design
point but also for a full type model are required these days. So we
conducted numerical analysis for all operating points by using
complete geometry through transient analysis. Transient analysis on
the complete geometry of a real product has the advantage of
simulating realistic flow. The results of this study show the variation of
a performance curve by modifying the above-mentioned design
parameter.
Abstract: One of the important applications of gas turbines is
their utilization for heat recovery steam generator in combine-cycle technology. Exhaust flow and energy are two key parameters for
determining heat recovery steam generator performance which are mainly determined by the main gas turbine components performance
data. For this reason a method was developed for determining the
exhaust energy in the new edition of ASME PTC22. The result of this investigation shows that the method of standard has considerable
error. Therefore in this paper a new method is presented for modifying of the performance calculation. The modified method is
based on exhaust gas constituent analysis and combustion calculations. The case study presented here by two kind of General
Electric gas turbine design data for validation of methodologies. The
result shows that the modified method is more precise than the ASME PTC22 method. The exhaust flow calculation deviation from
design data is 1.5-2 % by ASME PTC22 method so that the deviation regarding with modified method is 0.3-0.5%. Based on precision of
analyzer instruments, the method can be suitable alternative for gas
turbine standard performance test. In advance two methods are
proposed based on known and unknown fuel in modified method procedure. The result of this paper shows that the difference between
the two methods is below than %0.02. In according to reasonable esult of the second procedure (unknown fuel composition), the
method can be applied to performance evaluation of gas turbine, so that the measuring cost and data gathering should be reduced.
Abstract: Starting from the basic pillars of the supportability
analysis this paper queries its characteristics in LCI (Life Cycle
Integration) environment. The research methodology contents a
review of modern logistics engineering literature with the objective to
collect and synthesize the knowledge relating to standards of
supportability design in e-logistics environment. The results show
that LCI framework has properties which are in fully compatibility
with the requirement of simultaneous logistics support and productservice
bundle design. The proposed approach is a contribution to the
more comprehensive and efficient supportability design process.
Also, contributions are reflected through a greater consistency of
collected data, automated creation of reports suitable for different
analysis, as well as the possibility of their customization according
with customer needs. In addition to this, convenience of this approach
is its practical use in real time. In a broader sense, LCI allows
integration of enterprises on a worldwide basis facilitating electronic
business.
Abstract: With the prevalence of computer and development of information technology, Geographic Information Systems (GIS) have long used for a variety of applications in electrical engineering. GIS are designed to support the analysis, management, manipulation and mapping of spatial data. This paper presents several usages of GIS in power utilities such as automated route selection for the construction of new power lines which uses a dynamic programming model for route optimization, load forecasting and optimizing planning of substation-s location and capacity with comprehensive algorithm which involves an accurate small-area electric load forecasting procedure and simulates the different cost functions of substations.
Abstract: The previous researches focused on the influence of
anthropogenic greenhouse gases exerting global warming, but not
consider whether desert sand may warm the planet, this could be
improved by accounting for sand's physical and geometric properties.
Here we show, sand particles (because of their geometry) at the desert
surface form an extended surface of up to 1 + π/4 times the planar area
of the desert that can contact sunlight, and at shallow depths of the
desert form another extended surface of at least 1 + π times the planar
area that can contact air. Based on this feature, an enhanced heat
exchange system between sunlight, desert sand, and air in the spaces
between sand particles could be built up automatically, which can
increase capture of solar energy, leading to rapid heating of the sand
particles, and then the heating of sand particles will dramatically heat
the air between sand particles. The thermodynamics of deserts may
thus have contributed to global warming, especially significant to
future global warming if the current desertification continues to
expand.
Abstract: Intelligent schools are those which use IT devices and
technologies as media software, hardware and networks to improve
learning process. On the other hand Strategic management is a field
that deals with the major intended and emergent initiatives taken by
general managers on behalf of owners, involving utilization of resources, to enhance the performance of firms in their external environments. Here, we present a model Strategic Management System that has been applied on some schools and have made strict
improvement.
Abstract: The paper discuses the effect of initial stresses on the reflection coefficients of plane waves in a dissipative medium. Basic governing equations are formulated in context of Biot's incremental deformation theory. These governing equations are solved analytically to obtain the dimensional phase velocities of plane waves propagating in plane of symmetry. Closed-form expressions for the reflection coefficients of P and SV waves- incident at the free surface of an initially stressed dissipative medium are obtained. Numerical computations, using these expressions, are carried out for a particular model. Computations made with the results predicted in presence and absence of the initial stresses and the results have been shown graphically. The study shows that the presence of compressive initial stresses increases the velocity of longitudinal wave (P-wave) but diminishes that of transverse wave (SV-wave). Also the numerical results presented indicate that initial stresses and dissipation might affect the reflection coefficients significantly.