Abstract: In this paper, a block code to minimize the peak-toaverage
power ratio (PAPR) of orthogonal frequency division
multiplexing (OFDM) signals is proposed. It is shown that cyclic
shift and codeword inversion cause not change to peak envelope
power. The encoding rule for the proposed code comprises of
searching for a seed codeword, shifting the register elements, and
determining codeword inversion, eliminating the look-up table for
one-to-one correspondence between the source and the coded data.
Simulation results show that OFDM systems with the proposed code
always have the minimum PAPR.
Abstract: A fast settling multipath CMOS OTA for high speed
switched capacitor applications is presented here. With the basic
topology similar to folded-cascode, bandwidth and DC gain of the
OTA are enhanced by adding extra paths for signal from input to
output. Designed circuit is simulated with HSPICE using level 49
parameters (BSIM 3v3) in 0.35mm standard CMOS technology. DC
gain achieved is 56.7dB and Unity Gain Bandwidth (UGB) obtained
is 1.15GHz. These results confirm that adding extra paths for signal
can improve DC gain and UGB of folded-cascode significantly.
Abstract: Pretreatment is an essential step in the conversion of
lignocellulosic biomass to fermentable sugar that used for biobutanol
production. Among pretreatment processes, microwave is considered
to improve pretreatment efficiency due to its high heating efficiency,
easy operation, and easily to combine with chemical reaction. The
main objectives of this work are to investigate the feasibility of
microwave pretreatment to enhance enzymatic hydrolysis of
corncobs and to determine the optimal conditions using response
surface methodology. Corncobs were pretreated via two-stage
pretreatment in dilute sodium hydroxide (2 %) followed by dilute
sulfuric acid 1 %. Pretreated corncobs were subjected to enzymatic
hydrolysis to produce reducing sugar. Statistical experimental design
was used to optimize pretreatment parameters including temperature,
residence time and solid-to-liquid ratio to achieve the highest amount
of glucose. The results revealed that solid-to-liquid ratio and
temperature had a significant effect on the amount of glucose.
Abstract: The influence of copper promoters and reaction
conditions on the formation of alcohols byproducts of a common
Fischer-Tropsch synthesis used iron-based catalysts were investigated.
A good compromise of 28%Cu/FeKLaSiO2 can lead to the
optimization of an improved Fischer-Tropsch catalyst. The product
distribution shifts towards hydrocarbons with increasing the reaction
temperature, while pressure promotes the formation of alcohols. It was
found that the production of either alcohols or hydrocarbons followed
A-S-F distributions, and their α parameters were essentially different
which indicated a competition in the growing chain between the two
species. TPD after acetaldehyde adsorption gave strong evidence of
the insertion of a C1 oxygen-containing species into an alkyl chain.
Abstract: This paper proposes a novel approach to the question of lithofacies classification based on an assessment of the uncertainty in the classification results. The proposed approach has multiple neural networks (NN), and interval neutrosophic sets (INS) are used to classify the input well log data into outputs of multiple classes of lithofacies. A pair of n-class neural networks are used to predict n-degree of truth memberships and n-degree of false memberships. Indeterminacy memberships or uncertainties in the predictions are estimated using a multidimensional interpolation method. These three memberships form the INS used to support the confidence in results of multiclass classification. Based on the experimental data, our approach improves the classification performance as compared to an existing technique applied only to the truth membership. In addition, our approach has the capability to provide a measure of uncertainty in the problem of multiclass classification.
Abstract: The objective of this research intends to create a suitable model of distance training for community leaders in the upper northeastern region of Thailand. The implementation of the research process is divided into four steps: The first step is to analyze relevant documents. The second step deals with an interview in depth with experts. The third step is concerned with constructing a model. And the fourth step takes aim at model validation by expert assessments. The findings reveal the two important components for constructing an appropriate model of distance training for community leaders in the upper northeastern region. The first component consists of the context of technology management, e.g., principle, policy and goals. The second component can be viewed in two ways. Firstly, there are elements comprising input, process, output and feedback. Secondly, the sub-components include steps and process in training. The result of expert assessments informs that the researcher-s constructed model is consistent and suitable and overall the most appropriate.
Abstract: A higher order spline interpolated contour obtained
with up-sampling of homogenously distributed coordinates for
segmentation of kidney region in different classes of ultrasound
kidney images has been developed and presented in this paper. The
performance of the proposed method is measured and compared with
modified snake model contour, Markov random field contour and
expert outlined contour. The validation of the method is made in
correspondence with expert outlined contour using maximum coordinate
distance, Hausdorff distance and mean radial distance
metrics. The results obtained reveal that proposed scheme provides
optimum contour that agrees well with expert outlined contour.
Moreover this technique helps to preserve the pixels-of-interest
which in specific defines the functional characteristic of kidney. This
explores various possibilities in implementing computer-aided
diagnosis system exclusively for US kidney images.
Abstract: In this study the integration of an absorption heat
pump (AHP) with the concentration section of an industrial pulp and
paper process is investigated using pinch technology. The optimum
design of the proposed water-lithium bromide AHP is then achieved
by minimizing the total annual cost. A comprehensive optimization is
carried out by relaxation of all stream pressure drops as well as heat
exchanger areas involving in AHP structure. It is shown that by
applying genetic algorithm optimizer, the total annual cost of the
proposed AHP is decreased by 18% compared to one resulted from
simulation.
Abstract: Question answering (QA) aims at retrieving precise information from a large collection of documents. Most of the Question Answering systems composed of three main modules: question processing, document processing and answer processing. Question processing module plays an important role in QA systems to reformulate questions. Moreover answer processing module is an emerging topic in QA systems, where these systems are often required to rank and validate candidate answers. These techniques aiming at finding short and precise answers are often based on the semantic relations and co-occurrence keywords. This paper discussed about a new model for question answering which improved two main modules, question processing and answer processing which both affect on the evaluation of the system operations. There are two important components which are the bases of the question processing. First component is question classification that specifies types of question and answer. Second one is reformulation which converts the user's question into an understandable question by QA system in a specific domain. The objective of an Answer Validation task is thus to judge the correctness of an answer returned by a QA system, according to the text snippet given to support it. For validating answers we apply candidate answer filtering, candidate answer ranking and also it has a final validation section by user voting. Also this paper described new architecture of question and answer processing modules with modeling, implementing and evaluating the system. The system differs from most question answering systems in its answer validation model. This module makes it more suitable to find exact answer. Results show that, from total 50 asked questions, evaluation of the model, show 92% improving the decision of the system.
Abstract: In this research, the main aim is to investigate the
antimicrobial effectiveness of ammonyx solutions finishing on
Sweatshirt Sport with immersion method. 60 Male healthy subjects
(football player) participated in this study. They were dressed in a
Sweatshirt for 14 days and some microbes found on them were
investigated. The antimicrobial effect of different ammonyx
solutions(1/100, 1/500, 1/1000, 1/2000 v/v solutions of Ammonyx)
on the identified microbes was studied by the zone inhabitation
method in vitro. In the next step the Sweatshirt Sports were treated
with the same different solutions of ammonyx and the antimicrobial
effectiveness was assessed by colony count method in different times
and the results were compared whit untreated ones. Some mechanical
properties of treated cotton/polyester yarn that used in Sweatshirt
Sport were measured after 30 days and were compared with
untreated one. Finally after finishing, scanning electron microscopy
(SEM) was used to compare the surfaces of the finished and
unfinished specimens. The results showed the presence of five
pathogenic microbes on Sweatshirt Sports such as Escherichia coli,
Staphylococcus aureus, Aspergillus, Mucor and Candida. The
inhalation time for treated on Sweatshirt Sports improved. The
amount of colony growth on treated clothes reduced considerably
and moreover the mechanical tests results showed no significant
deterioration effect of studies properties in comparison to the
untreated yarn. The visual examination of the SEM indicated that the
antimicrobial treatments were applied usefully to fabrics.
Abstract: This research study examines cases of Saudi Arabian
universities and female academics for work environment issues
within the context of design management applications. The study
proposes use of design research, ergonomics and systems design
thinking to develop the university design which facilitates removal of
physical and cognitive barriers for female academics. Review of
literature demonstrates that macro and micro ergonomic combined
with design management and system design strategies can
significantly improve the workplace design for female academics.
The university design model would be prepared based on the analyses
of primary data obtained from archived documents, participants'
observation logs, photo audits, focus groups and semi-structured
interviews of currently employed female academics in the selected
case universities.
Abstract: In this paper, the application of thermal spray
coatings in high speed shafts by a revolution up to 23000 RPM
has been studied. Gas compressor shafts are worn in contact
zone with journal therefore will be undersized. Wear
mechanisms of compressor shaft were identified. The
predominant wear mechanism is abrasion wear. The worn
surface was coated by hard WC-Co cermets using high
velocity oxy fuel (HVOF) after preparation. The shafts were in
satisfactory service in 8000h period. The metallurgical and
Tribological studies has been made on the worn and coated
shaft using optical microscopy, scanning electron microscopy
(SEM) and X-ray diffraction.
Abstract: There is inadequate information on the practice of
female genital mutilation (FGM) in the UK, and there are often
myths and perceptions within communities that influence the
effectiveness of prevention programmes. This means it is difficult to
address the trends and changes in the practice in the UK.
To this end, FORWARD undertook novel and innovative research
using the Participatory Ethnographic and Evaluative Research
(PEER) method to explore the views of women from Eritrea, Sudan,
Somalia and Ethiopia that live in London and Bristol (two UK cities).
Women-s views, taken from PEER interviews, reflected reasons for
continued practice of FGM: marriageability, the harnessing and
control of female sexuality, and upholding traditions from their
countries of origin. It was also clear that the main supporters of the
practice were believed to be older women within families and
communities.
Women described the impact FGM was having on their lives as
isolating. And although it was clearly considered a private and
personal matter, they developed a real sense of connection with their
peers within the research process.
The women were overwhelmingly positive about combating the
practice, although they believed it would probably take a while
before it ends completely. They also made concrete
recommendations on how to improve support services for women
affected by FGM: Training for professionals (particularly in
healthcare), increased engagement with, and outreach to,
communities, culturally appropriate materials and information made
available and accessible to communities, and more consequent
implementation of legislation.
Finally, the women asked for more empathy and understanding,
particularly from health professionals. Rather than presenting FGM
as a completely alien and inconceivable practice, it may help for
those looking into these women-s lives and working with them to
understand the social and economic context in which the practice
takes place.
Abstract: In this paper, an automatic determination algorithm for nuclear magnetic resonance (NMR) spectra of the metabolites in the living body by magnetic resonance spectroscopy (MRS) without human intervention or complicated calculations is presented. In such method, the problem of NMR spectrum determination is transformed into the determination of the parameters of a mathematical model of the NMR signal. To calculate these parameters efficiently, a new model called modified Hopfield neural network is designed. The main achievement of this paper over the work in literature [30] is that the speed of the modified Hopfield neural network is accelerated. This is done by applying cross correlation in the frequency domain between the input values and the input weights. The modified Hopfield neural network can accomplish complex dignals perfectly with out any additinal computation steps. This is a valuable advantage as NMR signals are complex-valued. In addition, a technique called “modified sequential extension of section (MSES)" that takes into account the damping rate of the NMR signal is developed to be faster than that presented in [30]. Simulation results show that the calculation precision of the spectrum improves when MSES is used along with the neural network. Furthermore, MSES is found to reduce the local minimum problem in Hopfield neural networks. Moreover, the performance of the proposed method is evaluated and there is no effect on the performance of calculations when using the modified Hopfield neural networks.
Abstract: In Croatia, the majority of cultured marine fish species are reared in net cages. The intensive production of the fish in net cages may generate the considerable amount of bio waste and change water quality especially in enclosed and semi-enclosed coastal areas. The aim of this paper is to assess the potential impact of sea bass (Dicentrarchus labrax L.) cage farm on water quality. The weak relationship between food supply and water quality parameters (nutrient content and phytoplankton biomass) was found, but significant changes in oxygen saturation was observed in the cages during the warmer period of a year especially in the morning (occasionally it dropped below 70 %). Despite of, satisfactory results of water quality parameters, it is necessary to establish comprehensive monitoring process, especially to include quality assessment of fouling communities.
Abstract: We discuss the signal detection through nonlinear
threshold systems. The detection performance is assessed by the
probability of error Per . We establish that: (1) when the signal is
complete suprathreshold, noise always degrades the signal detection
both in the single threshold system and in the parallel array of
threshold devices. (2) When the signal is a little subthreshold, noise
degrades signal detection in the single threshold system. But in the
parallel array, noise can improve signal detection, i.e., stochastic
resonance (SR) exists in the array. (3) When the signal is predominant
subthreshold, noise always can improve signal detection and SR
always exists not only in the single threshold system but also in the
parallel array. (4) Array can improve signal detection by raising the
number of threshold devices. These results extend further the
applicability of SR in signal detection.
Abstract: this paper presents a novel scheme which is capable of reducing the error rate and improves the transmission performance in the asynchronous cooperative MIMO systems. A case study of image transmission is applied to prove the efficient of scheme. The linear dispersion structure is employed to accommodate the cooperative wireless communication network in the dynamic topology of structure, as well as to achieve higher throughput than conventional space–time codes based on orthogonal designs. The LDPC encoder without girth-4 and the STBC encoder with guard intervals are respectively introduced. The experiment results show that the combined coder of LDPC-STBC with guard intervals can be the good error correcting coders and BER performance in the asynchronous cooperative communication. In the case study of image transmission, the results show that in the transmission process, the image quality which is obtained by applied combined scheme is much better than it which is not applied the scheme in the asynchronous cooperative MIMO systems.
Abstract: In this work we study the effect of several covariates X on a censored response variable T with unknown probability distribution. In this context, most of the studies in the literature can be located in two possible general classes of regression models: models that study the effect the covariates have on the hazard function; and models that study the effect the covariates have on the censored response variable. Proposals in this paper are in the second class of models and, more specifically, on least squares based model approach. Thus, using the bootstrap estimate of the bias, we try to improve the estimation of the regression parameters by reducing their bias, for small sample sizes. Simulation results presented in the paper show that, for reasonable sample sizes and censoring levels, the bias is always smaller for the new proposals.
Abstract: Natural gas usually includes H2S component which is
very toxic, hazardous and corrosive to environment, human being and
process equipments, respectively. Therefore, sweetening of the gas
(separation of H2S) is inevitable. To achieve this purpose, using
packed-bed columns with liquid absorbents such as MEA or DEA is
very common. Due to some problems of usual packed columns
especially high pressure drop of gas phase, a novel kind of them
called wetted-wire column (WWC) has been invented. The column
decreases the pressure drop significantly and improves the absorption
efficiency. The packings are very thin rods (like wire) and as long as
column. The column has 100 wires with a triangular arrangement and
counter current flows of gas and liquid phases. The observation
showed that at the same conditions, the absorption performance was
quite comparable to conventional packed-bed towers and a very low
pressure drop.
Abstract: This paper details a new concept of using compressed air as a potential zero pollution power source for motorbikes. In place of an internal combustion engine, the motorbike is equipped with an air turbine transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor diameters, casing diameters and ratio of rotor to casing diameters of the turbine have been considered and analyzed. It is concluded that the work output is found optimum for some typical values of rotor / casing diameter ratios. In this study, the maximum power works out to 3.825 kW (5.20 HP) for casing diameter of 200 mm and rotor to casing diameter ratio of 0.65 to 0.60 which is sufficient to run motorbike.