Abstract: This paper reports the results of an experimental study
conducted to characterise the gas-liquid multiphase flows
experienced within a vertical riser transporting a range of gas-liquid
flow rates. The scale experiments were performed using an
air/silicone oil mixture within a 6 m long riser. The superficial air
velocities studied ranged from 0.047 to 2.836 m/ s, whilst
maintaining a liquid superficial velocity at 0.047 m/ s. Measurements
of the mean cross-sectional and time average radial void fraction
were obtained using a wire mesh sensor (WMS). The data were
recorded at an acquisition frequency of 1000 Hz over an interval of
60 seconds. For the range of flow conditions studied, the average
void fraction was observed to vary between 0.1 and 0.9. An analysis
of the data collected concluded that the observed void fraction was
strongly affected by the superficial gas velocity, whereby the higher
the superficial gas velocity, the higher was the observed average void
fraction. The average void fraction distributions observed were in
good agreement with the results obtained by other researchers. When
the air-silicone oil flows were fully developed reasonably symmetric
profiles were observed, with the shape of the symmetry profile being
strongly dependent on the superficial gas velocity.
Abstract: A design of communication area for infrared
electronic-toll-collection systems to provide an extended
communication interval in the vehicle traveling direction and
regular boundary between contiguous traffic lanes is proposed.
By utilizing two typical low-cost commercial infrared LEDs with
different half-intensity angles Φ1/2 = 22◦ and 10◦, the radiation
pattern of the emitter is designed to properly adjust the spatial
distribution of the signal power. The aforementioned purpose
can be achieved with an LED array in a three-piece structure
with appropriate mounting angles. With this emitter, the influence
of the mounting parameters, including the mounting height and
mounting angles of the on-board unit and road-side unit, on the
system performance in terms of the received signal strength and
communication area are investigated. The results reveal that, for
our emitter proposed in this paper, the ideal ”long-and-narrow”
characteristic of the communication area is very little affected by
these mounting parameters. An optimum mounting configuration is
also suggested.
Abstract: This paper presents the optimal design and development
of an axial flux motor for blood pump application. With the design
objective of maximizing the motor efficiency and torque, different
topologies of AFPM machine has been examined. Selection of
optimal magnet fraction, Halbach arrangement of rotor magnets and
the use of Soft Magnetic Composite (SMC) material for the stator
core results in a novel motor with improved efficiency and torque
profile. The results of the 3D Finite element analysis for the novel
motor have been shown.
Abstract: This paper describes new computer vision algorithms
that have been developed to track moving objects as part of a
long-term study into the design of (semi-)autonomous vehicles. We
present the results of a study to exploit variable kernels for tracking in
video sequences. The basis of our work is the mean shift
object-tracking algorithm; for a moving target, it is usual to define a
rectangular target window in an initial frame, and then process the data
within that window to separate the tracked object from the background
by the mean shift segmentation algorithm. Rather than use the
standard, Epanechnikov kernel, we have used a kernel weighted by the
Chamfer distance transform to improve the accuracy of target
representation and localization, minimising the distance between the
two distributions in RGB color space using the Bhattacharyya
coefficient. Experimental results show the improved tracking
capability and versatility of the algorithm in comparison with results
using the standard kernel. These algorithms are incorporated as part of
a robot test-bed architecture which has been used to demonstrate their
effectiveness.
Abstract: Video Mosaicing is the stitching of selected frames of
a video by estimating the camera motion between the frames and
thereby registering successive frames of the video to arrive at the
mosaic. Different techniques have been proposed in the literature for
video mosaicing. Despite of the large number of papers dealing with
techniques to generate mosaic, only a few authors have investigated
conditions under which these techniques generate good estimate of
motion parameters. In this paper, these techniques are studied under
different videos, and the reasons for failures are found. We propose
algorithms with incorporation of outlier removal algorithms for better
estimation of motion parameters.
Abstract: Vision based tracking problem is solved through a
combination of optical flow, MACH filter and log r-θ mapping.
Optical flow is used for detecting regions of movement in video
frames acquired under variable lighting conditions. The region of
movement is segmented and then searched for the target. A template
is used for target recognition on the segmented regions for detecting
the region of interest. The template is trained offline on a sequence of
target images that are created using the MACH filter and log r-θ
mapping. The template is applied on areas of movement in
successive frames and strong correlation is seen for in-class targets.
Correlation peaks above a certain threshold indicate the presence of
target and the target is tracked over successive frames.
Abstract: The aim of this paper is to emphasize and alleviate the effect of phase noise due to imperfect local oscillators on the performances of a Multi-Carrier CDMA system. After the cancellation of Common Phase Error (CPE), an iterative approach is introduced which iteratively estimates Inter-Carrier Interference (ICI) components in the frequency domain and cancels their contribution in the time domain. Simulation are conducted in order to investigate the achievable performances for several parameters, such as the spreading factor, the modulation order, the phase noise power and the transmission Signal-to-Noise Ratio.
Abstract: Purpose of this work is to develop an automatic classification system that could be useful for radiologists in the breast cancer investigation. The software has been designed in the framework of the MAGIC-5 collaboration. In an automatic classification system the suspicious regions with high probability to include a lesion are extracted from the image as regions of interest (ROIs). Each ROI is characterized by some features based generally on morphological lesion differences. A study in the space features representation is made and some classifiers are tested to distinguish the pathological regions from the healthy ones. The results provided in terms of sensitivity and specificity will be presented through the ROC (Receiver Operating Characteristic) curves. In particular the best performances are obtained with the Neural Networks in comparison with the K-Nearest Neighbours and the Support Vector Machine: The Radial Basis Function supply the best results with 0.89 ± 0.01 of area under ROC curve but similar results are obtained with the Probabilistic Neural Network and a Multi Layer Perceptron.
Abstract: In this paper, we propose a novel concept of relative
distance measurement using Stereo Vision Technology and discuss
its implementation on a FPGA based real-time image processor. We
capture two images using two CCD cameras and compare them.
Disparity is calculated for each pixel using a real time dense disparity
calculation algorithm. This algorithm is based on the concept of
indexed histogram for matching. Disparity being inversely
proportional to distance (Proved Later), we can thus get the relative
distances of objects in front of the camera. The output is displayed on
a TV screen in the form of a depth image (optionally using pseudo
colors). This system works in real time on a full PAL frame rate (720
x 576 active pixels @ 25 fps).
Abstract: This paper presents a review on published literature
and experimental works on local sands for possible use as proppant,
specifically those from Terengganu coastal area. This includes
examination on characteristics of sand samples and selection of
experiments for proppant testing. Sand samples from identified areas
were tested according to particle size distribution, density, roundness
and sphericity, turbidity and mineralogy. Results from sand samples
were compared against proppant specifications set by API RP 56 and
selected commercial proppants. The present study found that the size
distribution, sphericity, turbidity and bulk density of Terengganu
sands are at par with some of commercial proppants. Nevertheless,
Terengganu sand samples do not completely surpass the required
roundness for use as proppant.
Abstract: Malaysia is aggressive in promoting the usage of ICT
to its mass population through the support by the government
policies and programs targeting the general population. However,
with the uneven distribution of the basic telecommunication
infrastructure between the urban and rural area, cost for being
“interconnected" that is considered high among the poorer rural
population and the lack of local contents that suit the rural population
needs or lifestyles, it is still a challenge for Malaysia to achieve its
Vision 2020 Agenda moving the nation towards an information
society by the year 2020. Among the existing programs that have
been carried out by the government to encourage the usage of ICT by
the rural population is “Kedaikom", a community telecenter with the
general aim is to engage the community to get exposed and to use the
ICT, encouraging the diffusion of the ICT technology to the rural
population. The research investigated by using a questionnaire
survey of how Kedaikom, as a community telecenter could play a
role in encouraging the rural or underserved community to use the
ICT. The result from the survey has proven that the community
telecenter could bridge the digital divide between the underserved
rural population and the well-accessed urban population in Malaysia.
More of the rural population, especially from the younger generation
and those with higher educational background are using the
community telecenter to be connected to the ICT.
Abstract: Mobile Ad hoc Networks is an autonomous system of
mobile nodes connected by multi-hop wireless links without
centralized infrastructure support. As mobile communication gains
popularity, the need for suitable ad hoc routing protocols will
continue to grow. Efficient dynamic routing is an important research
challenge in such a network. Bandwidth constrained mobile devices
use on-demand approach in their routing protocols because of its
effectiveness and efficiency. Many researchers have conducted
numerous simulations for comparing the performance of these
protocols under varying conditions and constraints. Most of them are
not aware of MAC Protocols, which will impact the relative
performance of routing protocols considered in different network
scenarios. In this paper we investigate the choice of MAC protocols
affects the relative performance of ad hoc routing protocols under
different scenarios. We have evaluated the performance of these
protocols using NS2 simulations. Our results show that the
performance of routing protocols of ad hoc networks will suffer when
run over different MAC Layer protocols.
Abstract: This article presents the results using a parametric approach and a Wavelet Transform in analysing signals emitting from the sperm whale. The extraction of intrinsic characteristics of these unique signals emitted by marine mammals is still at present a difficult exercise for various reasons: firstly, it concerns non-stationary signals, and secondly, these signals are obstructed by interfering background noise. In this article, we compare the advantages and disadvantages of both methods: Auto Regressive models and Wavelet Transform. These approaches serve as an alternative to the commonly used estimators which are based on the Fourier Transform for which the hypotheses necessary for its application are in certain cases, not sufficiently proven. These modern approaches provide effective results particularly for the periodic tracking of the signal's characteristics and notably when the signal-to-noise ratio negatively effects signal tracking. Our objectives are twofold. Our first goal is to identify the animal through its acoustic signature. This includes recognition of the marine mammal species and ultimately of the individual animal (within the species). The second is much more ambitious and directly involves the intervention of cetologists to study the sounds emitted by marine mammals in an effort to characterize their behaviour. We are working on an approach based on the recordings of marine mammal signals and the findings from this data result from the Wavelet Transform. This article will explore the reasons for using this approach. In addition, thanks to the use of new processors, these algorithms once heavy in calculation time can be integrated in a real-time system.
Abstract: One of object oriented software developing problem
is the difficulty of searching the appropriate and suitable objects for
starting the system. In this work, ontologies appear in the part of
supporting the object discovering in the initial of object oriented
software developing. There are many researches try to demonstrate
that there is a great potential between object model and ontologies.
Constructing ontology from object model is called ontology
engineering can be done; On the other hand, this research is aiming to
support the idea of building object model from ontology is also
promising and practical. Ontology classes are available online in any
specific areas, which can be searched by semantic search engine.
There are also many helping tools to do so; one of them which are
used in this research is Protégé ontology editor and Visual Paradigm.
To put them together give a great outcome. This research will be
shown how it works efficiently with the real case study by using
ontology classes in travel/tourism domain area. It needs to combine
classes, properties, and relationships from more than two ontologies
in order to generate the object model. In this paper presents a simple
methodology framework which explains the process of discovering
objects. The results show that this framework has great value while
there is possible for expansion. Reusing of existing ontologies offers
a much cheaper alternative than building new ones from scratch.
More ontologies are becoming available on the web, and online
ontologies libraries for storing and indexing ontologies are increasing
in number and demand. Semantic and Ontologies search engines have
also started to appear, to facilitate search and retrieval of online
ontologies.
Abstract: This paper at first presents approximate analytical
solutions for systems of fractional differential equations using the
differential transform method. The application of differential
transform method, developed for differential equations of integer
order, is extended to derive approximate analytical solutions of
systems of fractional differential equations. The solutions of our
model equations are calculated in the form of convergent series with
easily computable components. After that a drive-response
synchronization method with linear output error feedback is
presented for “generalized projective synchronization" for a class of
fractional-order chaotic systems via a scalar transmitted signal.
Genesio_Tesi and Duffing systems are used to illustrate the
effectiveness of the proposed synchronization method.
Abstract: Nowadays, many manufacturing companies try to
reinforce their competitiveness or find a breakthrough by considering
collaboration. In Korea, more than 900 manufacturing companies are
using web-based collaboration systems developed by the
government-led project, referred to as i-Manufacturing. The system
supports some similar functions of Product Data Management (PDM)
as well as Project Management System (PMS). A web-based
collaboration system provides many useful functions for collaborative
works. This system, however, does not support new linking services
between buyers and suppliers. Therefore, in order to find new
collaborative partners, this paper proposes a framework which creates
new connections between buyers and suppliers facilitating their
collaboration, referred to as Excellent Manufacturer Scouting System
(EMSS). EMSS plays a role as a bridge between overseas buyers and
suppliers. As a part of study on EMSS, we also propose an evaluation
method of manufacturability of potential partners with six main factors.
Based on the results of evaluation, buyers may get a good guideline to
choose their new partners before getting into negotiation processes
with them.
Abstract: This paper describes the designs of a first and second
generation autonomous gas monitoring system and the successful
field trial of the final system (2nd generation). Infrared sensing
technology is used to detect and measure the greenhouse gases
methane (CH4) and carbon dioxide (CO2) at point sources. The
ability to monitor real-time events is further enhanced through the
implementation of both GSM and Bluetooth technologies to
communicate these data in real-time. These systems are robust,
reliable and a necessary tool where the monitoring of gas events in
real-time are needed.
Abstract: This paper investigates experimentally and
analytically the torsion behavior of steel fibered high strength self
compacting concrete beams reinforced by GFRP bars. Steel fibered
high strength self compacting concrete (SFHSSCC) and GFRP bars
became in the recent decades a very important materials in the
structural engineering field. The use of GFRP bars to replace steel
bars has emerged as one of the many techniques put forward to
enhance the corrosion resistance of reinforced concrete structures.
High strength concrete and GFRP bars attract designers and
architects as it allows improving the durability as well as the esthetics
of a construction. One of the trends in SFHSSCC structures is to
provide their ductile behavior and additional goal is to limit
development and propagation of macro-cracks in the body of
SFHSSCC elements. SFHSSCC and GFRP bars are tough, improve
the workability, enhance the corrosion resistance of reinforced
concrete structures, and demonstrate high residual strengths after
appearance of the first crack. Experimental studies were carried out
to select effective fiber contents. Three types of volume fraction from
hooked shape steel fibers are used in this study, the hooked steel
fibers were evaluated in volume fractions ranging between 0.0%,
0.75% and 1.5%. The beams shape is chosen to create the required
forces (i.e. torsion and bending moments simultaneously) on the test
zone. A total of seven beams were tested, classified into three groups.
All beams, have 200cm length, cross section of 10×20cm,
longitudinal bottom reinforcement of 3
Abstract: Firms have invested heavily in knowledge
management (KM) with the aim to build a knowledge capability and
use it to achieve a competitive advantage. Research has shown,
however, that not all knowledge management projects succeed. Some
studies report that about 84% of knowledge management projects
fail. This paper has integrated studies on the impediments to
knowledge management into a theoretical framework. Based on this
framework, five cases documenting failed KM initiatives were
analysed. The analysis gave us a clear picture about why certain KM
projects fail. The high failure rate of KM can be explained by the
gaps that exist between users and management in terms of KM
perceptions and objectives
Abstract: Meshless Finite Element Methods, namely element-free Galerkin and point-interpolation method were implemented and tested concerning their applicability to typical engineering problems like electrical fields and structural mechanics. A class-structure was developed which allows a consistent implementation of these methods together with classical FEM in a common framework. Strengths and weaknesses of the methods under investigation are discussed. As a result of this work joint usage of meshless methods together with classical Finite Elements are recommended.