Abstract: Multidrug resistant organisms have been taunting the
medical world for the last few decades. Even with new antibiotics
developed, resistant strains have emerged soon after. With the
advancement of nanotechnology, we investigated colloidal silver
nanoparticles for its antimicrobial activity against Pseudomonas
aeruginosa. This organism is a multidrug resistant which contributes
to the high morbidity and mortality in immunocompromised patients.
Five multidrug resistant strains were used in this study. The
antimicrobial effect was studied using the disc diffusion and broth
dilution techniques. An inhibition zone of 11 mm was observed with
10 μg dose of the nanoparticles. The nanoparticles exhibited MIC of
50 μg/ml when added at the lag phase and the subinhibitory
concentration was measured as 100 μg/ml. The MIC50 value showed
to be 15 μg/ml. This study suggests that silver nanoparticles can be
further developed as an antimicrobial agent, hence decreasing the
burden of the multidrug resistance phenomena.
Abstract: This paper is to present context-aware sensor grid
framework for agriculture and its design challenges. Use of sensor
networks in the domain of agriculture is not new. However, due to
the unavailability of any common framework, solutions that are
developed in this domain are location, environment and problem
dependent. Keeping the need of common framework for agriculture,
Context-Aware Sensor Grid Framework is proposed. It will be
helpful in developing solutions for majority of the problems related
to irrigation, pesticides spray, use of fertilizers, regular monitoring of
plot and yield etc. due to the capability of adjusting according to
location and environment. The proposed framework is composed of
three layer architecture including context-aware application layer,
grid middleware layer and sensor network layer.
Abstract: Tribological behavior and wear regimes of ascast
and heattreted Al-Cu-Mg matrix composites containing SiC
particles were studied using a pin-on-disc wear testing apparatus
against an EN32 steel counterface giving emphasis on wear rate as
a function of applied pressures (0.2, 0.6, 1.0 and 1.4 MPa) at
different sliding distances (1000, 2000, 3000, 4000 and 5000
meters) and at a fixed sliding speed of 3.35m/s. The results showed
that the composite exhibited lower wear rate than that of the matrix
alloy and the wear rate of the composites is noted to be invariant to
the sliding distance and is reducing by heat treatment. Wear
regimes such as low, mild and severe wear were observed as per the
Archard-s wear calculations. It is very interesting to note that the
mild wear is almost constant in all the wear regimes.
Abstract: In the present study, the effects of ultrasound as
emerging technology were investigated on germination stimulation,
amount of alpha-amylase activity on dry barley seeds before steeping
stage of malting process. All experiments were carried out at 20 KHz
on the ultrasonic generator in 3 different ultrasonic intensities (20, 60
and 100% setting from total power of device) and time (5, 10 and 15
min) at constant temperature (30C). For determining the effects of
these parameters on enzyme the Fuwa method assay based on the
decreased staining value of blue starch–iodine complexes employed
for measurement an activity. The results of these assays were
analyzed by Qualitek4 software using the Taguchi statistical method
to evaluate the factor-s effects on enzyme activity. It has been found
that when malting barley is irradiated with an ultrasonic power, a
stimulating effect occurs as to the enzyme activity.
Abstract: Recent years, adaptive pushover methods have been
developed for seismic analysis of structures. Herein, the accuracy of
the displacement-based adaptive pushover (DAP) method, which is
introduced by Antoniou and Pinho [2004], is evaluated for Irregular
buildings. The results are compared to the force-based procedure.
Both concrete and steel frame structures, asymmetric in plan and
elevation are analyzed and also torsional effects are taking into the
account. These analyses are performed using both near fault and far
fault records. In order to verify the results, the Incremental Dynamic
Analysis (IDA) is performed.
Abstract: In this paper, a Smart Home Service Robot, McBot II,
which performs mess-cleanup function etc. in house, is designed much
more optimally than other service robots. It is newly developed in
much more practical system than McBot I which we had developed
two years ago. One characteristic attribute of mobile platforms
equipped with a set of dependent wheels is their omni- directionality
and the ability to realize complex translational and rotational
trajectories for agile navigation in door. An accurate coordination of
steering angle and spinning rate of each wheel is necessary for a
consistent motion. This paper develops trajectory controller of
3-wheels omni-directional mobile robot using fuzzy azimuth estimator.
A specialized anthropomorphic robot manipulator which can be
attached to the housemaid robot McBot II, is developed in this paper.
This built-in type manipulator consists of both arms with 3 DOF
(Degree of Freedom) each and both hands with 3 DOF each. The
robotic arm is optimally designed to satisfy both the minimum
mechanical size and the maximum workspace. Minimum mass and
length are required for the built-in cooperated-arms system. But that
makes the workspace so small. This paper proposes optimal design
method to overcome the problem by using neck joint to move the arms
horizontally forward/backward and waist joint to move them
vertically up/down. The robotic hand, which has two fingers and a
thumb, is also optimally designed in task-based concept. Finally, the
good performance of the developed McBot II is confirmed through
live tests of the mess-cleanup task.
Abstract: The great challenge of the agricultural sector is to
produce more crop from less water, which can be achieved by
increasing crop water productivity. The modernization of the
irrigation systems offers a number of possibilities to expand the
economic productivity of water and improve the virtual water status.
The objective of the present study is to assess the global water
productivity (GWP) within the major irrigation command areas of
I.R. Iran. For this purpose, fourteen irrigation command areas where
located in different areas of Iran were selected. In order to calculate
the global water productivity of irrigation command areas, all data on
the delivered water to cropping pattern, cultivated area, crops water
requirement, and yield production rate during 2002-2006 were
gathered. In each of the command areas it seems that the cultivated
crops have a higher amount of virtual water and thus can be replaced
by crops with less virtual water. This is merely suggested due to crop
water consumption and at the time of replacing crops, economic
value as well as cultural and political factors must be considered. The
results indicated that the lowest GWP belongs to Mahyar and
Borkhar irrigation areas, 0.24 kg m-3, and the highest is that of the
Dez irrigation area, 0.81 kg m-3. The findings demonstrated that
water management in the two irrigation areas is just efficient. The
difference in the GWP of irrigation areas is due to variations in the
cropping pattern, amount of crop productions, in addition to the
effective factors in the water use efficiency in the irrigation areas.
Abstract: Computer networks are essential part in computerbased
information systems. The performance of these networks has a
great influence on the whole information system. Measuring the
usability criteria and customers satisfaction on small computer
network is very important. In this article, an effective approach for
measuring the usability of business network in an information system
is introduced. The usability process for networking provides us with a
flexible and a cost-effective way to assess the usability of a network
and its products. In addition, the proposed approach can be used to
certify network product usability late in the development cycle.
Furthermore, it can be used to help in developing usable interfaces
very early in the cycle and to give a way to measure, track, and
improve usability. Moreover, a new approach for fast information
processing over computer networks is presented. The entire data are
collected together in a long vector and then tested as a one input
pattern. Proposed fast time delay neural networks (FTDNNs) use
cross correlation in the frequency domain between the tested data and
the input weights of neural networks. It is proved mathematically and
practically that the number of computation steps required for the
presented time delay neural networks is less than that needed by
conventional time delay neural networks (CTDNNs). Simulation
results using MATLAB confirm the theoretical computations.
Abstract: This paper presents Simulation and experimental
study aimed at investigating the effectiveness of an adaptive artificial
neural network stabilizer on enhancing the damping torque of a
synchronous generator. For this purpose, a power system comprising
a synchronous generator feeding a large power system through a
short tie line is considered. The proposed adaptive neuro-control
system consists of two multi-layered feed forward neural networks,
which work as a plant model identifier and a controller. It generates
supplementary control signals to be utilized by conventional
controllers. The details of the interfacing circuits, sensors and
transducers, which have been designed and built for use in tests, are
presented. The synchronous generator is tested to investigate the
effect of tuning a Power System Stabilizer (PSS) on its dynamic
stability. The obtained simulation and experimental results verify the
basic theoretical concepts.
Abstract: A recent neurospiking coding scheme for feature extraction from biosonar echoes of various plants is examined with avariety of stochastic classifiers. Feature vectors derived are employedin well-known stochastic classifiers, including nearest-neighborhood,single Gaussian and a Gaussian mixture with EM optimization.Classifiers' performances are evaluated by using cross-validation and bootstrapping techniques. It is shown that the various classifers perform equivalently and that the modified preprocessing configuration yields considerably improved results.
Abstract: This paper seeks to develop simple yet practical and
efficient control scheme that enables cooperating arms to handle a
flexible beam. Specifically the problem studied herein is that of two
arms rigidly grasping a flexible beam and such capable of generating
forces/moments in such away as to move a flexible beam along a
predefined trajectory. The paper develops a sliding mode control law
that provides robustness against model imperfection and uncertainty.
It also provides an implicit stability proof. Simulation results for two
three joint arms moving a flexible beam, are presented to validate the
theoretical results.
Abstract: Diffuse viral encephalitis may lack fever and other cardinal signs of infection and hence its distinction from other acute encephalopathic illnesses is challenging. Often, the EEG changes seen routinely are nonspecific and reflect diffuse encephalopathic changes only. The aim of this study was to use nonlinear dynamic mathematical techniques for analyzing the EEG data in order to look for any characteristic diagnostic patterns in diffuse forms of encephalitis.It was diagnosed on clinical, imaging and cerebrospinal fluid criteria in three young male patients. Metabolic and toxic encephalopathies were ruled out through appropriate investigations. Digital EEGs were done on the 3rd to 5th day of onset. The digital EEGs of 5 male and 5 female age and sex matched healthy volunteers served as controls.Two sample t-test indicated that there was no statistically significant difference between the average values in amplitude between the two groups. However, the standard deviation (or variance) of the EEG signals at FP1-F7 and FP2-F8 are significantly higher for the patients than the normal subjects. The regularisation dimension is significantly less for the patients (average between 1.24-1.43) when compared to the normal persons (average between 1.41-1.63) for the EEG signals from all locations except for the Fz-Cz signal. Similarly the wavelet dimension is significantly less (P = 0.05*) for the patients (1.122) when compared to the normal person (1.458). EEGs are subdued in the case of the patients with presence of uniform patterns, manifested in the values of regularisation and wavelet dimensions, when compared to the normal person, indicating a decrease in chaotic nature.
Abstract: The square-lattice Ising model is the simplest system
showing phase transitions (the transition between the paramagnetic
phase and the ferromagnetic phase and the transition between the
paramagnetic phase and the antiferromagnetic phase) and critical
phenomena at finite temperatures. The exact solution of the squarelattice
Ising model with free boundary conditions is not known for
systems of arbitrary size. For the first time, the exact solution of
the Ising model on the square lattice with free boundary
conditions is obtained after classifying all )
spin configurations with the microcanonical transfer matrix. Also, the
phase transitions and critical phenomena of the square-lattice Ising
model are discussed using the exact solution on the square
lattice with free boundary conditions.
Abstract: In this paper, we develop a Spatio-Temporal graph as
of a key component of our knowledge representation Scheme. We
design an integrated representation Scheme to depict not only present
and past but future in parallel with the spaces in an effective and
intuitive manner. The resulting multi-dimensional comprehensive
knowledge structure accommodates multi-layered virtual world
developing in the time to maximize the diversity of situations in the
historical context. This knowledge representation Scheme is to be used
as the basis for simulation of situations composing the virtual world
and for implementation of virtual agents' knowledge used to judge and
evaluate the situations in the virtual world. To provide natural contexts
for situated learning or simulation games, the virtual stage set by this
Spatio-Temporal graph is to be populated by agents and other objects
interrelated and changing which are abstracted in the ontology.
Abstract: This paper describes the optimization of a complex
dairy farm simulation model using two quite different methods of
optimization, the Genetic algorithm (GA) and the Lipschitz
Branch-and-Bound (LBB) algorithm. These techniques have been
used to improve an agricultural system model developed by Dexcel
Limited, New Zealand, which describes a detailed representation of
pastoral dairying scenarios and contains an 8-dimensional parameter
space. The model incorporates the sub-models of pasture growth and
animal metabolism, which are themselves complex in many cases.
Each evaluation of the objective function, a composite 'Farm
Performance Index (FPI)', requires simulation of at least a one-year
period of farm operation with a daily time-step, and is therefore
computationally expensive. The problem of visualization of the
objective function (response surface) in high-dimensional spaces is
also considered in the context of the farm optimization problem.
Adaptations of the sammon mapping and parallel coordinates
visualization are described which help visualize some important
properties of the model-s output topography. From this study, it is
found that GA requires fewer function evaluations in optimization
than the LBB algorithm.
Abstract: Tread design has evolved over the years to achieve the common tread pattern used in current vehicles. However, to meet safety and comfort requirements, tread design considers more than one design factor. Tread design must consider the grip and drainage, and the manner in which to reduce rolling noise, which is one of the main factors considered by manufacturers. The main objective of this study was the application the computational fluid dynamics (CFD) technique to simulate the contact surface of the tire and ground. The results demonstrated an air-Pumping and large pressure drop effect in the process of contact surface. The results also revealed that the pressure can be used to analyze sound pressure level (SPL).
Abstract: A study was undertaken to assess the potential of an
Algal Turf Scrubber to remove nitrogen from aquaculture effluent to
reduce environmental pollution. High total ammonia nitrogen
concentrations were introduced to an Algal Turf Scrubber developed
under varying hydraulic surface loading rates of African catfish
(Clarius gariepinus) effluent in a recirculating aquaculture system.
Nutrient removal rates were not affected at total suspended solids
concentration of up to 0.04g TSS/l (P > 0.05). Nitrogen removal
rates 0.93-0.99g TAN/m²/d were recorded at very high loading rates
3.76-3.81 g TAN/m²/d. Total ammonia removal showed ½ order
kinetics between 1.6 to 2.3mg/l Total Ammonia Nitrogen
concentrations. Nitrogen removal increased with its loading, which
increased with hydraulic surface loading rate. Total Ammonia
Nitrogen removal by Algal turf scrubber was higher than reported
values for fluidized bed filters and trickling filters. The algal turf
scrubber also effectively removed nitrate thereby reducing the need
for water exchange.
Abstract: Due to the deregulation of the Electric Supply
Industry and the resulting emergence of electricity market, the
volumes of power purchases are on the rise all over the world. In a
bid to meet the customer-s demand in a reliable and yet economic
manner, utilities purchase power from the energy market over and
above its own production. This paper aims at developing an optimal
power purchase model with two objectives viz economy and
environment ,taking various functional operating constraints such as
branch flow limits, load bus voltage magnitudes limits, unit capacity
constraints and security constraints into consideration.The price of
purchased power being an uncertain variable is modeled using fuzzy
logic. DEMO (Differential Evolution For Multi-objective
Optimization) is used to obtain the pareto-optimal solution set of the
multi-objective problem formulated. Fuzzy set theory has been
employed to extract the best compromise non-dominated solution.
The results obtained on IEEE 30 bus system are presented and
compared with that of NSGAII.
Abstract: The model-based approach to user interface design relies on developing separate models that are capturing various aspects about users, tasks, application domain, presentation and dialog representations. This paper presents a task modeling approach for user interface design and aims at exploring the mappings between task, domain and presentation models. The basic idea of our approach is to identify typical configurations in task and domain models and to investigate how they relate each other. A special emphasis is put on application-specific functions and mappings between domain objects and operational task structures. In this respect, we will distinguish between three layers in the task decomposition: a functional layer, a planning layer, and an operational layer.
Abstract: Orthogonal Frequency Division Multiplexing
(OFDM) is an efficient method of data transmission for high speed
communication systems. However, the main drawback of OFDM
systems is that, it suffers from the problem of high Peak-to-Average
Power Ratio (PAPR) which causes inefficient use of the High Power
Amplifier and could limit transmission efficiency. OFDM consist of
large number of independent subcarriers, as a result of which the
amplitude of such a signal can have high peak values. In this paper,
we propose an effective reduction scheme that combines DCT and
SLM techniques. The scheme is composed of the DCT followed by
the SLM using the Riemann matrix to obtain phase sequences for the
SLM technique. The simulation results show PAPR can be greatly
reduced by applying the proposed scheme. In comparison with
OFDM, while OFDM had high values of PAPR –about 10.4dB our
proposed method achieved about 4.7dB reduction of the PAPR with
low complexities computation. This approach also avoids
randomness in phase sequence selection, which makes it simpler to
decode at the receiver. As an added benefit, the matrices can be
generated at the receiver end to obtain the data signal and hence it is
not required to transmit side information (SI).