Abstract: The article deals with a biomechanics analysis of the classic bicross start with a backward movement of the bike. This is a case study analyzing this type of start in two bicross riders representing the Czech Republic. Based on the 3D kinematic analysis and with a special emphasis on the ankle movement we have divided the start into five phases – phase n. 1 – reaction time, phase n. 2 – preparation movements time, phase n. 3 – first pedal stroke time, phase n. 4 – dead point pedal passage time, phase n. 5 – second pedal stroke time. Further we have demonstrated the significance of kinematic characteristics in various stages of the bicross start including their values and the extent of change. These primarily include the vector of the instantaneous velocity of the head, wrists, elbows, shoulders, hip and knee joints. The significant angle characteristics have been noted in elbow, shoulder, hip and knee joints. The results of this work indicate the types of movement prevailing in the respective phases and as such are expected to serve as a basis for further analyses of this movement structure performed, however, on a large research sample.
Abstract: This study examines the stack ventilation performance of an office building located in Taipei, Taiwan. Atriums in this building act as stacks that facilitate buoyancy-driven ventilation. Computational Fluid Dynamic (CFD) simulations are used to identify interior airflow patterns, and then used these patterns to assess the building’s heat expulsion efficiency. Ambient temperatures of 20°C were adopted as the typical seasonal spring temperature range in Taipei. Further, “zero-wind” conditions are established to ensure simulation results reflected only the buoyancy effect. After checking results against neutral pressure level (NPL) level, airflow, air velocity, and indoor temperature stratification, the lower stack is modified to reduce the NPL in order to remove heat accumulated on the top floor.
Abstract: Heat transfer and laminar air flow over a double backward-facing step numerically studied in this paper. The simulations was performed by using ANSYS ICEM for meshing process and using ANSYS fluent 14 (CFD) for solving. The k-ɛ standard model adopted with Reynolds number varied between 98.5 to 512 and three step height at constant heat flux (q=2000 W/m2). The top of wall and bottom of upstream are insulated with bottom of downstream is heated. The results show increase in Nusselt number with increases of Reynolds number for all cases and the maximum of Nusselt number happens at the first step in compared to the second step. Due to increase of cross section area of downstream to generate sudden expansion then Nusselt number decrease but the profile of Nusselt number keep same trend for all cases where increase after the first and second steps. Recirculation region after the first and second steps are denoted by contour of streamline velocity. The higher augmentation of heat transfer rate observed for case 1 at Reynolds number of 512 and heat flux q=2000 W/m2.
Abstract: The purpose of the research is to investigate the energetic feature of the backpack load on soldier’s gait with variation of the trunk flexion angle. It is believed that the trunk flexion variation of the loaded gait may cause a significant difference in the energy cost which is often in practice in daily life. To this end, seven healthy Korea military personnel participated in the experiment and are tested under three different walking postures comprised of the small, natural and large trunk flexion. There are around 5 degree differences of waist angle between each trunk flexion. The ground reaction forces were collected from the force plates and motion kinematic data are measured by the motion capture system. Based on these data, the impulses, momentums and mechanical works done on the center of body mass (COM) during the double support phase were computed. The result shows that the push-off and heel strike impulse are not relevant to the trunk flexion change, however the mechanical work by the push-off and heel strike were changed by the trunk flexion variation. It is because the vertical velocity of the COM during the double support phase is increased significantly with an increase in the trunk flexion. Therefore, we can know that the gait efficiency of the loaded gait depends on the trunk flexion angle. Also, even though the gravitational impulse and pre-collision momentum are changed by the trunk flexion variation, the after-collision momentum is almost constant regardless of the trunk flexion variation.
Abstract: Darcy’s Law is a well-known constitutive equation describing the flow of a fluid through a porous medium. The equation shows a relationship between the superficial or Darcy velocity and the pressure gradient which was first experimentally observed by Henry Darcy in 1855-1856. In this study, we apply homogenization method to Stokes equation in order to derive Darcy’s Law. The process of deriving the equation is complicated, especially in multidimensional domain. Thus, for the sake of simplicity, we use the indicial notation as well as the homogenization. This combination provides a smooth, simple and easy technique to derive Darcy’s Law.
Abstract: In this study, artificial limestone brick samples are produced by using wood sawdust wastes (WSW) having different grades of sizes and limestone powder waste (LPW). The thermo-elastic properties of produced brick samples in various WSW amounts are investigated. At 30% WSW replacement with LPW in the brick sample the thermal conductivity value is effectively reduced and the reduction in the thermal conductivity value of brick sample at 30% WSW replacement with LPW is about 38.9% as compared with control sample. The energy conservation in buildings by using LPW and WSW in masonry brick material production having low thermal conductivity reduces energy requirements. A strong relationship is also found among the thermal conductivity, unit weight and ultrasonic pulse velocity values of brick samples produced. It shows a potential to be used for walls, wooden board substitute, alternative to the concrete blocks, ceiling panels, sound barrier panels, absorption materials etc.
Abstract: A new Meta heuristic approach called "Randomized gravitational emulation search algorithm (RGES)" for solving large size set covering problems has been designed. This algorithm is found upon introducing randomization concept along with the two of the four primary parameters -velocity- and -gravity- in physics. A new heuristic operator is introduced in the domain of RGES to maintain feasibility specifically for the set covering problem to yield best solutions. The performance of this algorithm has been evaluated on a large set of benchmark problems from OR-library. Computational results showed that the randomized gravitational emulation search algorithm - based heuristic is capable of producing high quality solutions. The performance of this heuristic when compared with other existing heuristic algorithms is found to be excellent in terms of solution quality.
Abstract: Different approaches for heating\cooling of stirred tanks, coils and jackets, are investigated using computational fluid dynamics (CFD).A time-dependant sliding mesh approach is applied to simulate the flow in both conditions. The investigations are carried out under the turbulent flow conditions for a Rushton impeller and heating elements are considered isothermal. The flow behavior and temperature distribution are studied for each case and heat transfer coefficient is calculated. Results show different velocity profiles for each case. Unsteady temperature distribution is not similar for different cases .In the case of the coiled stirred vessel more uniform temperature and higher heat transfer coefficient is resulted.
Abstract: An accurate prediction of the minimum fluidization
velocity is a crucial hydrodynamic aspect of the design of fluidized
bed reactors. Common approaches for the prediction of the minimum
fluidization velocities of binary-solid fluidized beds are first
discussed here. The data of our own careful experimental
investigation involving a binary-solid pair fluidized with water is
presented. The effect of the relative composition of the two solid
species comprising the fluidized bed on the bed void fraction at the
incipient fluidization condition is reported and its influence on the
minimum fluidization velocity is discussed. In this connection, the
capability of packing models to predict the bed void fraction is also
examined.
Abstract: A numerical study on the effect of side-dump angle on
fuel droplets sizing and effective mass fraction have been
investigated in present paper. The mass of fuel vapor inside the
flammability limit is named as the effective mass fraction. In the first
step we have considered a side-dump combustor with dump angle of
0o (acrossthe cylinder) and by increasing the entrance airflow velocity
from 20 to 30, 40 and 50 (m/s) respectively, the mean diameter of
fuel droplets sizing and effective mass fraction have been studied.
After this step, we have changed the dump angle from 0o to 30o,45o
and finally 60o in direction of cylinderand also we have increased the
entrance airflow velocity from 20 up to 50 (m/s) with the amount of
growth of 10(m/s) in each step, to examine its effects on fuel droplets
sizing as well as effective mass fraction. With rise of entrance airflow
velocity, these calculations are repeated in each step too. The results
show, with growth of dump-angle the effective mass fraction has
been decreased and the mean diameter of droplets sizing has been
increased. To fulfill the calculations a modified version of KIVA-3V
code which is a transient, three-dimensional, multiphase,
multicomponent code for the analysis of chemically reacting flows
with sprays, is used.
Abstract: The present work involves measurements to examine
the effects of initial conditions on aerodynamic and acoustic
characteristics of a Jet at M=0.8 by changing the orientation of sharp
edged orifice plate. A thick plate with chamfered orifice presented divergent and convergent openings when it was flipped over. The centerline velocity was found to decay more rapidly for divergent
orifice and that was consistent with the enhanced mass entrainment
suggesting quicker spread of the jet compared with that from the convergent orifice. The mixing layer region elucidated this effect of
initial conditions at an early stage – the growth was found to be comparatively more pronounced for the divergent orifice resulting in
reduced potential core size. The acoustic measurements, carried out in the near field noise region outside the jet within potential core
length, showed the jet from the divergent orifice to be less noisy. The frequency spectra of the noise signal exhibited that in the initial
region of comparatively thin mixing layer for the convergent orifice,
the peak registered a higher SPL and a higher frequency as well. The noise spectra and the mixing layer development suggested a direct correlation between the coherent structures developing in the initial
region of the jet and the noise captured in the surrounding near field.
Abstract: The purpose of suspension system in automobiles is to
improve the ride comfort and road handling. In this research the ride
and handling performance of a specific automobile with passive
suspension system is compared to a proposed fuzzy logic semi active
suspension system designed for that automobile. The bodysuspension-
wheel system is modeled as a two degree of freedom
quarter car model. MATLAB/SIMULINK [1] was used for
simulation and controller design. The fuzzy logic controller is based
on two inputs namely suspension velocity and body velocity. The
output of the fuzzy controller is the damping coefficient of the
variable damper. The result shows improvement over passive
suspension method.
Abstract: An explicit axisymmetrical FE methodology is
developed here to study the particle temperature arising in WC-Co
particle on an AISI 1045 steel substrate. Parameters of constitutive
Johnson-cook model were used for simulation. The results show that
particle velocity and kinetic energy have important role in
temperature arising of particles.
Abstract: The steady coupled dissipative layers, called
Marangoni mixed convection boundary layers, in the presence of a
magnetic field and solute concentration that are formed along the
surface of two immiscible fluids with uniform suction or injection
effects is examined. The similarity boundary layer equations are
solved numerically using the Runge-Kutta Fehlberg with shooting
technique. The Marangoni, buoyancy and external pressure gradient
effects that are generated in mixed convection boundary layer flow
are assessed. The velocity, temperature and concentration boundary
layers thickness decrease with the increase of the magnetic field
strength and the injection to suction. For buoyancy-opposed flow, the
Marangoni mixed convection parameter enhances the velocity
boundary layer but decreases the temperature and concentration
boundary layers. However, for the buoyancy-assisted flow, the
Marangoni mixed convection parameter decelerates the velocity but
increases the temperature and concentration boundary layers.
Abstract: Vortices can develop in intakes of turbojet and turbo
fan aero engines during high power operation in the vicinity of solid
surfaces. These vortices can cause catastrophic damage to the engine.
The factors determining the formation of the vortex include both
geometric dimensions as well as flow parameters. It was shown that
the threshold at which the vortex forms or disappears is also
dependent on the initial flow condition (i.e. whether a vortex forms
after stabilised non vortex flow or vice-versa). A computational fluid
dynamics study was conducted to determine the difference in
thresholds between the two conditions. This is the first reported
numerical investigation of the “memory effect". The numerical
results reproduce the phenomenon reported in previous experimental
studies and additional factors, which had not been previously studied,
were investigated. They are the rate at which ambient velocity
changes and the initial value of ambient velocity. The former was
found to cause a shift in the threshold but not the later. It was also
found that the varying condition thresholds are not symmetrical about
the neutral threshold. The vortex to no vortex threshold lie slightly
further away from the neutral threshold compared to the no vortex to
vortex threshold. The results suggests that experimental investigation
of vortex formation threshold performed either in vortex to no vortex
conditions, or vice versa, solely may introduce mis-predictions
greater than 10%.
Abstract: This paper presents the use of three-dimensional finite
elements coupled with infinite elements to investigate the ground
vibrations at the surface in terms of the peak particle velocity (PPV)
due to construction of the first bore of the Dublin Port Tunnel. This
situation is analysed using a commercially available general-purpose
finite element package ABAQUS. A series of parametric studies is
carried out to examine the sensitivity of the predicted vibrations to
variations in the various input parameters required by finite element
method, including the stiffness and the damping of ground. The
results of this study show that stiffness has a more significant effect
on the PPV rather than the damping of the ground.
Abstract: Non-premixed turbulent combustion Computational Fluid Dynamics (CFD) has been carried out in a simplified methanefuelled coaxial jet combustor employing Large Eddy Simulation (LES). The objective of this study is to evaluate the performance of LES in modelling non-premixed combustion using a commercial software, FLUENT, and investigate the effects of the grid density and chemistry models employed on the accuracy of the simulation results. A comparison has also been made between LES and Reynolds Averaged Navier-Stokes (RANS) predictions. For LES grid sensitivity test, 2.3 and 6.2 million cell grids are employed with the equilibrium model. The chemistry model sensitivity analysis is achieved by comparing the simulation results from the equilibrium chemistry and steady flamelet models. The predictions of the mixture fraction, axial velocity, species mass fraction and temperature by LES are in good agreement with the experimental data. The LES results are similar for the two chemistry models but influenced considerably by the grid resolution in the inner flame and near-wall regions.
Abstract: A numerical study has been conducted to investigate the influence of fin pitch and relative humidity on the heat transfer performance of the fin-and-tube heat exchangers having plain fin geometry under dehumidifying conditions. The analysis is done using the ratio between the heat transfer coefficients in totally wet conditions and those in totally dry conditions using the appropriate correlations for both dry and wet conditions. For a constant relative humidity, it is found that the heat transfer coefficient increases with the increase of the air frontal velocity. By contrast, the fin efficiency decreases when the face velocity is increased. Apparently, this phenomenon is attributed to the path of condensate drainage. For the influence of relative humidity, the results showed an increase in heat transfer performance and a decrease in wet fin efficiency when relative humidity increases. This is due to the higher amount of mass transfer encountered at higher relative humidity. However, it is found that the effect of fin pitch on the heat transfer performance depends strongly on the face velocity. At lower frontal velocity the heat transfer increases with fin pitch. Conversely, an increase in fin pitch gives lower heat transfer coefficients when air velocity is increased.
Abstract: In order to better understand the performance of
screen channel liquid acquisition devices (LADs) in liquid oxygen (LOX), a computational fluid dynamics (CFD) simulation of LOX passing through a LAD screen channel was conducted. In the
simulation, the screen is taken as a 'porous jump' where the pressure
drop across the screen depends on the incoming velocity and is formulated by Δp = Av + Bv2
. The CFD simulation reveals the importance of the pressure losses due to the flow entering from
across the screen and impacting and merging with the channel flow
and the vortices in the channel to the cumulative flow resistance. In fact, both the flow resistance of flows impact and mergence and the
resistance created by vortices are much larger than the friction and dynamic pressure losses in the channel and are comparable to the
flow resistance across the screen. Therefore, these resistances in the
channel must be considered as part of the evaluation for the LAD
channel performance. For proper operation of a LAD in LOX these resistances must be less than the bubble point pressure for the screen
channel in LOX. The simulation also presents the pressure and velocity distributions within the LAD screen channel, expanding the understanding of the fluid flow characteristics within the channel.
Abstract: The migration of a deformable drop in simple shear
flow at finite Reynolds numbers is investigated numerically by
solving the full Navier-Stokes equations using a finite
difference/front tracking method. The objectives of this study are to
examine the effectiveness of the present approach to predict the
migration of a drop in a shear flow and to investigate the behavior of
the drop migration with different drop sizes and non-unity viscosity
ratios. It is shown that the drop deformation depends strongly on the
capillary number, so that; the proper non-dimensional number for the
interfacial tension is the capillary number. The rate of migration
increased with increasing the drop radius. In other words, the
required time for drop migration to the centreline decreases. As the
viscosity ratio increases, the drop rotates more slowly and the
lubrication force becomes stronger. The increased lubrication force
makes it easier for the drop to migrate to the centre of the channel.
The migration velocity of the drop vanishes as the drop reaches the
centreline under viscosity ratio of one and non-unity viscosity ratios.
To validate the present calculations, some typical results are
compared with available experimental and theoretical data.