Abstract: In this current contribution, authors are dedicated to
investigate influence of the crystal lamellae orientation on
electromechanical behaviors of relaxor ferroelectric Poly
(vinylidene fluoride –trifluoroethylene -chlorotrifluoroethylene)
(P(VDF-TrFE-CTFE)) films by control of polymer microstructure,
aiming to picture the full map of structure-property relationship. In
order to define their crystal orientation films, terpolymer films were
fabricated by solution-casting, stretching and hot-pressing process.
Differential scanning calorimetry, impedance analyzer, and tensile
strength techniques were employed to characterize crystallographic
parameters, dielectric permittivity, and elastic Young’s modulus
respectively. In addition, large electrical induced out-of-plane
electrostrictive strain was obtained by cantilever beam mode.
Consequently, as-casted pristine films exhibited surprisingly high
electrostrictive strain 0.1774% due to considerably small value of
elastic Young’s modulus although relatively low dielectric
permittivity. Such reasons contributed to large mechanical elastic
energy density. Instead, due to 2 folds increase of elastic Young’s
modulus and less than 50% augmentation of dielectric constant, fullycrystallized
film showed weak electrostrictive behavior and
mechanical energy density as well. And subjected to mechanical
stretching process, Film C exhibited stronger dielectric constant and
out-performed electrostrictive strain over Film B because edge-on
crystal lamellae orientation induced by uniaxially mechanical stretch.
Hot-press films were compared in term of cooling rate. Rather large
electrostrictive strain of 0.2788% for hot-pressed Film D in
quenching process was observed although its dielectric permittivity
equivalent to that of pristine as-casted Film A, showing highest
mechanical elastic energy density value of 359.5 J/m3. In hot-press
cooling process, dielectric permittivity of Film E saw values at 48.8
concomitant with ca.100% increase of Young’s modulus. Films with
intermediate mechanical energy density were obtained.
Abstract: Excessive vibration means increased wear, increased
repair efforts, bad product selection & quality and high energy
consumption. This may be sometimes experienced by cavitation or
suction/discharge recirculation which could occur only when net
positive suction head available NPSHA drops below the net positive
suction head required NPSHR. Cavitation can cause axial surging, if it
is excessive, will damage mechanical seals, bearings, possibly other
pump components frequently, and shorten the life of the impeller.
Efforts have been made to explain Suction Energy (SE), Specific
Speed (Ns), Suction Specific Speed (Nss), NPSHA, NPSHR & their
significance, possible reasons of cavitation /internal recirculation, its
diagnostics and remedial measures to arrest and prevent cavitation in
this paper. A case study is presented by the author highlighting that
the root cause of unwanted noise and vibration is due to cavitation,
caused by high specific speeds or inadequate net- positive suction
head available which results in damages to material surfaces of
impeller & suction bells and degradation of machine performance, its
capacity and efficiency too. Author strongly recommends revisiting
the technical specifications of CW pumps to provide sufficient NPSH
margin ratios >1.5, for future projects and Nss be limited to 8500 -
9000 for cavitation free operation.
Abstract: Energy has a prominent role for development of
nations. Countries which have energy resources also have strategic
power in the international trade of energy since it is essential for all
stages of production in the economy. Thus, it is important for
countries to analyze the weaknesses and strength of the system. On
the other side, international trade is one of the fields that are analyzed
as a complex network via network analysis. Complex network is one
of the tools to analyze complex systems with heterogeneous agents
and interaction between them. A complex network consists of nodes
and the interactions between these nodes. Total properties which
emerge as a result of these interactions are distinct from the sum of
small parts (more or less) in complex systems. Thus, standard
approaches to international trade are superficial to analyze these
systems. Network analysis provides a new approach to analyze
international trade as a network. In this network, countries constitute
nodes and trade relations (export or import) constitute edges. It
becomes possible to analyze international trade network in terms of
high degree indicators which are specific to complex networks such
as connectivity, clustering, assortativity/disassortativity, centrality,
etc. In this analysis, international trade of crude oil and coal which
are types of fossil fuel has been analyzed from 2005 to 2014 via
network analysis. First, it has been analyzed in terms of some
topological parameters such as density, transitivity, clustering etc.
Afterwards, fitness to Pareto distribution has been analyzed via
Kolmogorov-Smirnov test. Finally, weighted HITS algorithm has
been applied to the data as a centrality measure to determine the real
prominence of countries in these trade networks. Weighted HITS
algorithm is a strong tool to analyze the network by ranking countries
with regards to prominence of their trade partners. We have
calculated both an export centrality and an import centrality by
applying w-HITS algorithm to the data. As a result, impacts of the
trading countries have been presented in terms of high-degree
indicators.
Abstract: Multiple Sclerosis (MS) is a disease which affects the
central nervous system and causes balance problem. In clinical, this
disorder is usually evaluated using static posturography. Some linear
or nonlinear measures, extracted from the posturographic data (i.e.
center of pressure, COP) recorded during a balance test, has been
used to analyze postural control of MS patients. In this study, the
trend (TREND) and the sample entropy (SampEn), two nonlinear
parameters were chosen to investigate their relationships with the
expanded disability status scale (EDSS) score. 40 volunteers with
different EDSS scores participated in our experiments with eyes open
(EO) and closed (EC). TREND and 2 types of SampEn (SampEn1
and SampEn2) were calculated for each combined COP’s position
signal. The results have shown that TREND had a weak negative
correlation to EDSS while SampEn2 had a strong positive correlation
to EDSS. Compared to TREND and SampEn1, SampEn2 showed a
better significant correlation to EDSS and an ability to discriminate
the MS patients in the EC case. In addition, the outcome of the study
suggests that the multi-dimensional nonlinear analysis could provide
some information about the impact of disability progression in MS on
dynamics of the COP data.
Abstract: This paper aims to analysis the behavior of DC corona
discharge in wire-to-plate electrostatic precipitators (ESP). Currentvoltage
curves are particularly analyzed. Experimental results show
that discharge current is strongly affected by the applied voltage. The proposed method of current identification is to use the method
of least squares. Least squares problems that of into two categories:
linear or ordinary least squares and non-linear least squares,
depending on whether or not the residuals are linear in all unknowns.
The linear least-squares problem occurs in statistical regression
analysis; it has a closed-form solution. A closed-form solution (or
closed form expression) is any formula that can be evaluated in a
finite number of standard operations. The non-linear problem has no
closed-form solution and is usually solved by iterative.
Abstract: With the advancement of knowledge about the utility
and impact of sustainability, its feasibility has been explored into
different walks of life. Scientists, however; have established their
knowledge in four areas viz environmental, economic, social and
cultural, popularly termed as four pillars of sustainability. Aspects of
environmental and economic sustainability have been rigorously
researched and practiced and huge volume of strong evidence of
effectiveness has been founded for these two sub-areas. For the social
and cultural aspects of sustainability, dependable evidence of
effectiveness is still to be instituted as the researchers and
practitioners are developing and experimenting methods across the
globe. Therefore, the present research aimed to identify globally used
practices of social and cultural sustainability and through evidence
synthesis assess their outcomes to determine the effectiveness of
those practices. A PICO format steered the methodology which
included all populations, popular sustainability practices including
walkability/cycle tracks, social/recreational spaces, privacy, health &
human services and barrier free built environment, comparators
included ‘Before’ and ‘After’, ‘With’ and ‘Without’, ‘More’ and
‘Less’ and outcomes included Social well-being, cultural coexistence,
quality of life, ethics and morality, social capital, sense of
place, education, health, recreation and leisure, and holistic
development. Search of literature included major electronic
databases, search websites, organizational resources, directory of
open access journals and subscribed journals. Grey literature,
however, was not included. Inclusion criteria filtered studies on the
basis of research designs such as total randomization, quasirandomization,
cluster randomization, observational or single studies
and certain types of analysis. Studies with combined outcomes were
considered but studies focusing only on environmental and/or
economic outcomes were rejected. Data extraction, critical appraisal
and evidence synthesis was carried out using customized tabulation,
reference manager and CASP tool. Partial meta-analysis was carried
out and calculation of pooled effects and forest plotting were done.
As many as 13 studies finally included for final synthesis explained
the impact of targeted practices on health, behavioural and social
dimensions. Objectivity in the measurement of health outcomes
facilitated quantitative synthesis of studies which highlighted the
impact of sustainability methods on physical activity, Body Mass
Index, perinatal outcomes and child health. Studies synthesized
qualitatively (and also quantitatively) showed outcomes such as
routines, family relations, citizenship, trust in relationships, social
inclusion, neighbourhood social capital, wellbeing, habitability and
family’s social processes. The synthesized evidence indicates slight
effectiveness and efficacy of social and cultural sustainability on the
targeted outcomes. Further synthesis revealed that such results of this
study are due weak research designs and disintegrated implementations. If architects and other practitioners deliver their
interventions in collaboration with research bodies and policy
makers, a stronger evidence-base in this area could be generated.
Abstract: Environmental concerns about the scarcity of marine
resources are critical driving forces for firms aiming to prepare their
supply chains for sustainability. Building on previous work, this
paper highlights the implementation of good practices geared towards
sustainable operations in the seafood department, which were
pursued in an exploratory retailer case. Outcomes of the adopted
environmentally and socially acceptable fish retailing strategies,
ranged from traceability, to self-certification and eco-labelling. The
consequences for business were, as follows: stronger collaboration
and trust across the chain of custody, improvement of sponsors’
image and of consumers’ loyalty and, progress in the Greenpeace
retailers’ evaluation ranking.
Abstract: Rapid developments in technology in the present age
have made it necessary for communities to follow technological
developments and adapt themselves to these developments. One of
the fields that are most rapidly affected by these developments is
undoubtedly education. Determination of the attitudes of preservice
teachers, who live in an age of technology and get ready to raise
future individuals, is of paramount importance both educationally and
professionally. The purpose of this study was to analyze attitudes of
preservice teachers towards technology and some variables that
predict these attitudes (gender, daily duration of internet use, and the
number of technical devices owned). 329 preservice teachers
attending the education faculty of a large university in central Turkey
participated, on a volunteer basis, in this study, where relational
survey model was used as the research method. Research findings
reveal that preservice teachers’ attitudes towards technology are
positive and at the same time, the attitudes of male preservice
teachers towards technology are more positive than their female
counterparts. As a result of the stepwise multiple regression analysis
where factors predicting preservice teachers’ attitudes towards
technology, it was found that duration of daily internet use was the
strongest predictor of attitudes towards technology.
Abstract: The research investigates the causes of unemployment
in Namibia, Nigeria and South Africa and the role of Capital
Accumulation in reducing the unemployment profile of these
economies as proposed by the post-Keynesian economics. This is
conducted through extensive review of literature on the NAIRU
models and focused on the post-Keynesian view of unemployment
within the NAIRU framework. The NAIRU (non-accelerating
inflation rate of unemployment) model has become a dominant
framework used in macroeconomic analysis of unemployment. The
study views the post-Keynesian economics arguments that capital
accumulation is a major determinant of unemployment.
Unemployment remains the fundamental socio-economic challenge
facing African economies. It has been a burden to citizens of those
economies. Namibia, Nigeria, and South Africa are great African
nations battling with high unemployment rates. The high
unemployment rate in the country led the citizens to chase away
foreigners in the country claiming that they have taken away their
jobs. The study proposes there is a strong relationship between
capital accumulation and unemployment in Namibia, Nigeria, and
South Africa, and capital accumulation is responsible for high
unemployment rates in these countries. For the economies to achieve
steady state level of employment and satisfactory level of economic
growth and development, there is need for capital accumulation to
take place. The countries in the study have been selected after a
critical research and investigations. They are selected based on the
following criteria; African economies with high unemployment rates
above 15% and have about 40% of their workforce unemployed. This
level of unemployment is the critical level of unemployment in
Africa as expressed by International Labour Organization (ILO). And
finally, the African countries experience a slow growth in their Gross
fixed capital formation. Adequate statistical measures have been
employed using a time-series analysis in the study and the results
revealed that capital accumulation is the main driver of
unemployment performance in the chosen African countries. An
increase in the accumulation of capital causes unemployment to
reduce significantly. The results of the research work will be useful
and relevant to federal governments and ministries, departments and
agencies (MDAs) of Namibia, Nigeria and South Africa to resolve
the issue of high and persistent unemployment rates in their
economies which are great burden that slows growth and
development of developing economies. Also, the result can be useful
to World Bank, African Development Bank and International Labour
Organization (ILO) in their further research and studies on how to
tackle unemployment in developing and emerging economies.
Abstract: Strong anthropogenic impact has uncontrolled
consequences on the nature of the soil. Hence, up-to-date sustainable
methods of soil state improvement are essential. Investigators provide
the evidence that biochar can positively effects physical, chemical,
and biological soil properties and the abundance of mycorrhizal fungi
which are in the focus of this study. The main aim of the present
investigation is to demonstrate the effect of two types of plant growth
promoting bacteria (PGPB) inoculums along with the beech wood
biochar and mineral N additives on mycorrhizal colonization.
Experiment has been set up in laboratory conditions with containers
filled with arable soil from the protection zone of the main water
source “Brezova nad Svitavou”. Lactuca sativa (lettuce) has been
selected as a model plant. Based on the obtained data, it can be
concluded that mycorrhizal colonization increased as the result of
combined influence of biochar and PGPB inoculums amendment. In
addition, correlation analyses showed that the numbers of main
groups of cultivated bacteria were dependent on the degree of
mycorrhizal colonization.
Abstract: This paper presents the results of a study on the
influence of varying percentages of rock bridges along a basal surface
defining a biplanar failure mode. A pseudo-coupled-hydromechanical
brittle fracture analysis is adopted using the state-of-the-art code
Slope Model. Model results show that rock bridge failure is strongly
influenced by the incorporation of groundwater pressures. The
models show that groundwater pressure can promote total failure of a
5% rock bridge along the basal surface. Once the percentage of the
rock bridges increases to 10 and 15%, although, the rock bridges are
broken, full interconnection of the surface defining the basal surface
of the biplanar mode does not occur. Increased damage is caused
when the rock bridge is located at the daylighting end of the basal
surface in proximity to the blast damage zone. As expected, some
cracking damage is experienced in the blast damage zone, where
properties representing a good quality controlled damage blast
technique were assumed. Model results indicate the potential increase
of permeability towards the blast damage zone.
Abstract: The goal of this paper is to specify factors influencing
the profitability of selected banks. Next, a model will be created to
help establish variables that have a demonstrable influence on the
development of the selected banks' profitability ratios. Czech banks
and their international parent companies were selected for analyzing
profitability. Banks categorized as large banks (according to the
Czech National Bank's system, which ranks banks according to
balance sheet total) were selected to represent the Czech banks. Two
ratios, the return on assets ratio (ROA) and the return on equity ratio
(ROE) are used to assess bank profitability. Six endogenous and four
external indicators were selected from among other factors that
influence bank profitability. The data analyzed were for 2001–2013.
First, correlation analysis, which was supposed to eliminate
correlated values, was conducted. A large number of correlated
values were established on the basis of this analysis. The strongly
correlated values were omitted. Despite this, the subsequent
regression analysis of profitability for the individual banks that were
selected did not confirm that the selected variables influenced their
profitability. The studied factors' influence on bank profitability was
demonstrated only for Ceskoslovenska Obchodni Banka and Société
Générale using regression analysis. For Československa Obchodni
Banka, it was demonstrated that inflation level and the amount of the
central bank's interest rate influenced the return on assets ratio and
that capital adequacy and market concentration influenced the return
on equity ratio for Société Générale.
Abstract: Strong anthropogenic impact has uncontrolled
consequences on the nature of the soil. Hence, up-to-date sustainable
methods of soil state improvement are essential. Investigators provide
the evidence that biochar can positively effects physical, chemical,
and biological soil properties and the abundance of mycorrhizal fungi
which are in the focus of this study. The main aim of the present
investigation is to demonstrate the effect of two types of plant growth
promoting bacteria (PGPB) inoculums along with the beech wood
biochar and mineral N additives on mycorrhizal colonization.
Experiment has been set up in laboratory conditions with containers
filled with arable soil from the protection zone of the main water
source “Brezova nad Svitavou”. Lactuca sativa (lettuce) has been
selected as a model plant. Based on the obtained data, it can be
concluded that mycorrhizal colonization increased as the result of
combined influence of biochar and PGPB inoculums amendment. In
addition, correlation analyses showed that the numbers of main
groups of cultivated bacteria were dependent on the degree of
mycorrhizal colonization.
Abstract: Reduction of energy consumption in built
infrastructure, through the installation of energy-efficient
technologies, is a major approach to achieving sustainability. In
practice, the viability of energy efficiency projects strongly depends
on the cost reimbursement and profitability. These projects are
subject to failure if the actual cost savings do not reimburse the
project cost promptly. In such cases, refinancing could be a solution
to benefit from the long-term returns of the project, if implemented
wisely. However, very little is still known about the effect of
refinancing options on financial performance of energy efficiency
projects. In order to fill this gap, the present study investigates the
financial behavior of energy efficiency projects with focus on
refinancing options, such as Leveraged Loans. A System Dynamics
(SD) model is introduced, and the model application is presented
using an actual case-study data. The case study results indicate that
while high-interest start-ups make using Leveraged Loan inevitable,
refinancing can rescue the project and bring about profitability. This
paper also presents some managerial implications of refinancing
energy efficiency projects based on the case-study analysis. Results
of this study help to implement financially viable energy efficiency
projects so that the community could benefit from their
environmental advantages widely.
Abstract: Unemployment among the youth is a significant
problem in South Africa. Large corporations and the public sector
simply cannot create enough jobs. Too many youths in South Africa
currently do not consider entrepreneurship as an option in order to
become independent. Unlike the youth of the Netherlands, South
African youth prefer to find employment in the public or private
sector. The Netherlands has a much lower unemployment rate than
South Africa and the Dutch are generally very entrepreneurial. From
early on, entrepreneurship is considered a desirable career option in
the Netherlands. The purpose of this study was to determine whether
there is a difference in the perceptions of some Dutch and South
African students in terms of unemployment and entrepreneurship.
Questionnaires were distributed to students at the North West
University's Vaal Triangle campus in Vanderbijlpark in Gauteng,
South Africa and the Technical University of Delft in the
Netherlands. A descriptive statistical analysis approach was followed
and the means for the independent questions were calculated. The
results demonstrate that the Dutch students are not as concerned
about unemployment after completion of their studies as this is not as
significant a problem as it is in South Africa. Both groups had
positive responses towards the posed questions, but the South African
group felt more strongly about the issues. Both groups of students felt
that there was a need for more practical entrepreneurship training.
The South African education system should focus on practical
entrepreneurship training from a young age.
Abstract: A retrospective study conducted at Christian Medical
College (CMC) Teaching Hospital, Vellore, India on 14th August
2014 to assess the accuracy of clinically estimated foetal weight upon
labour admission. Estimating foetal weight is a crucial factor in
assessing maternal and foetal complications during and after labour.
Medical notes of ninety-eight postnatal women who fulfilled the
inclusion criteria were studied to evaluate the correlation between
their recorded Estimated Foetal Weight (EFW) on admission and
actual birth weight (ABW) of the newborn after delivery. Data
concerning maternal and foetal demographics was also noted.
Accuracy was determined by absolute percentage error and
proportion of estimates within 10% of ABW. Actual birth weights
ranged from 950-4080g. A strong positive correlation between EFW
and ABW (r=0.904) was noted. Term deliveries (≥40 weeks) in the
normal weight range (2500-4000g) had a 59.5% estimation accuracy
(n=74) compared to pre-term (4000g) were underestimated by 25% (n=3) and low birthweight
(LBW) babies were overestimated by 12.7% (n=9). Registrars who
estimated foetal weight were accurate in babies within normal weight
ranges. However, there needs to be an improvement in predicting
weight of macrosomic and LBW foetuses. We have suggested the use
of an amended version of the Johnson’s formula for the Indian
population for improvement and a need to re-audit once
implemented.
Abstract: Lateral torsional buckling is a global buckling mode
which should be considered in design of slender structural members
under flexure about their strong axis. It is possible to compute the
load which causes lateral torsional buckling of a beam by finite
element analysis, however, closed form equations are needed in
engineering practice for calculation ease which can be obtained by
using energy method. In lateral torsional buckling applications of
energy method, a proper function for the critical lateral torsional
buckling mode should be chosen which can be thought as the
variation of twisting angle along the buckled beam. Accuracy of the
results depends on how close is the chosen function to the exact
mode. Since critical lateral torsional buckling mode of the cantilever
I-beams varies due to material properties, section properties and
loading case, the hardest step is to determine a proper mode function
in application of energy method. This paper presents an approximate function for critical lateral
torsional buckling mode of doubly symmetric cantilever I-beams.
Coefficient matrices are calculated for concentrated load at free end,
uniformly distributed load and constant moment along the beam
cases. Critical lateral torsional buckling modes obtained by presented
function and exact solutions are compared. It is found that the modes
obtained by presented function coincide with differential equation
solutions for considered loading cases.
Abstract: The steady flow of a second order fluid through
constricted tube with slip velocity at wall is modeled and analyzed
theoretically. The governing equations are simplified by implying no
slip in radial direction. Based on Karman Pohlhausen procedure
polynomial solution for axial velocity profile is presented.
Expressions for pressure gradient, shear stress, separation and
reattachment points, and radial velocity are also calculated. The
effect of slip and no slip velocity on magnitude velocity, shear stress,
and pressure gradient are discussed and depicted graphically. It is
noted that when Reynolds number increases magnitude velocity of
the fluid decreases in both slip and no slip conditions. It is also found
that the wall shear stress, separation, and reattachment points are
strongly affected by Reynolds number.
Abstract: CuO thin films were deposited by spray ultrasonic
pyrolysis with different precursor solution. Two staring solution slats
were used namely: copper acetate and copper chloride. The influence
of these solutions on CuO thin films proprieties of is instigated. The
X rays diffraction (XDR) analysis indicated that the films deposed
with copper acetate are amorphous however the films elaborated with
copper chloride have monoclinic structure. UV- Visible transmission
spectra showed a strong absorbance of the deposited CuO thin films
in the visible region. Electrical characterization has shown that CuO
thin films prepared with copper acetate have a higher electrical
conductivity.
Abstract: Hydrogels are three-dimensional, hydrophilic,
polymeric networks composed of homopolymers or copolymers and
are insoluble in water due to the presence of chemical or physical
cross-links. When hydrogels come in contact with aqueous solutions,
they can effectively sorb and retain the dissolved substances,
depending on the nature of the monomeric units comprising the
hydrogel. For this reason, hydrogels have been proposed in several
studies as water purification agents. At the present work anionic
hydrogels bearing negatively charged –COO- groups were prepared
and investigated. These gels are based on sodium acrylate (ANa),
either homopolymerized (poly(sodiumacrylate), PANa) or
copolymerized (P(DMAM-co-ANa)) with N,N Dimethylacrylamide
(DMAM). The hydrogels were used to extract some model organic
dyes from water. It is found that cationic dyes are strongly sorbed and
retained by the hydrogels, while sorption of anionic dyes was
negligible. In all cases it was found that both maximum sorption
capacity and equilibrium binding constant varied from one dye to the
other depending on the chemical structure of the dye, the presence of
functional chemical groups and the hydrophobic-hydrophilic balance.
Finally, the nonionic hydrogel of the homopolymer poly(N,Ndimethylacrylamide),
PDMAM, was also used for reasons of
comparison.