Abstract: The governing differential equations of laminated
plate utilizing trigonometric shear deformation theory are derived
using energy approach. The governing differential equations
discretized by different radial basis functions are used to predict the
free vibration behavior of symmetric laminated composite plates.
Effect of orthotropy and span to thickness ratio on frequency
parameter of simply supported laminated plate is presented.
Numerical results show the accuracy and good convergence of radial
basis functions.
Abstract: This paper presents investigation effects of a sharp edged gust on aeroelastic behavior and time-domain response of a typical section model using Jones approximate aerodynamics for pure plunging motion. Flutter analysis has been done by using p and p-k methods developed for presented finite-state aerodynamic model for a typical section model (airfoil). Introduction of gust analysis as a linear set of ordinary differential equations in a simplified procedure has been carried out by using transformation into an eigenvalue problem.
Abstract: This paper presents a new function expansion method for finding traveling wave solution of a non-linear equation and calls it the (G'/G)-expansion method. The shallow water wave equation is reduced to a non linear ordinary differential equation by using a simple transformation. As a result the traveling wave solutions of shallow water wave equation are expressed in three forms: hyperbolic solutions, trigonometric solutions and rational solutions.
Abstract: This paper describes a low-power second-order filter
for a continuous-time chopper stabilized capacitive sensor interface,
integrated with a fully differential post-CMOS surface-micromachined
MEMS pressure sensor. The circuit uses a single-ended
folded-cascode operational amplifier and two GM-C filters connected
in cascade. The circuit is realized in a 0.18 μm CMOS process and
offers differential to single-ended conversion. The novelty of the
scheme is the cascade of two GM-C filters to achieve a second-order
filter while minimizing power dissipation. The simulated filter cutoff
frequency is 1.14 kHz at common-mode voltage 1.65 V,
operating from a 3.3 V supply while dissipating 172μW of power.
The filter achieves an operating range of 1V for an output load of
1MOhm and 10pF.
Abstract: The paper is concerned with the existence of solution
of nonlinear second order neutral stochastic differential inclusions
with infinite delay in a Hilbert Space. Sufficient conditions for the
existence are obtained by using a fixed point theorem for condensing
maps.
Abstract: The Kansei engineering is a technology which
converts human feelings into quantitative terms and helps designers
develop new products that meet customers- expectation. Standard
Kansei engineering procedure involves finding relationships between
human feelings and design elements of which many researchers have
found forward and backward relationship through various soft
computing techniques. In this paper, we proposed the framework of
Kansei engineering linking relationship not only between human
feelings and design elements, but also the whole part of product, by
constructing association rules. In this experiment, we obtain input
from emotion score that subjects rate when they see the whole part of
the product by applying semantic differentials. Then, association
rules are constructed to discover the combination of design element
which affects the human feeling. The results of our experiment
suggest the pattern of relationship of design elements according to
human feelings which can be derived from the whole part of product.
Abstract: This work investigated the steady state and dynamic
simulation of a fixed bed industrial naphtha reforming reactors. The
performance of the reactor was investigated using a heterogeneous
model. For process simulation, the differential equations are solved
using the 4th order Runge-Kutta method .The models were validated
against measured process data of an existing naphtha reforming plant.
The results of simulation in terms of components yields and
temperature of the outlet were in good agreement with empirical data.
The simple model displays a useful tool for dynamic simulation,
optimization and control of naphtha reforming.
Abstract: Phase transformation temperature is one of the most important parameters for the shape memory alloys (SMAs). The most popular method to determine these phase transformation temperatures is the Differential Scanning Calorimeter (DSC), but due to the limitation of the DSC testing itself, it made it difficult for the finished product which is not in the powder form. A novel method which uses the Universal Testing Machine has been conducted to determine the phase transformation temperatures. The Flexinol wire was applied with force and maintained throughout the experiment and at the same time it was heated up slowly until a temperature of approximately 1000C with direct current. The direct current was then slowly decreased to cool down the temperature of the Flexinol wire. All the phase transformation temperatures for Flexinol wire were obtained. The austenite start at 52.540C and austenite finish at 60.900C, while martensite start at 44.780C and martensite finish at 32.840C.
Abstract: The heart tissue is an excitable media. A Cellular
Automata is a type of model that can be used to model cardiac action
potential propagation. One of the advantages of this approach against
the methods based on differential equations is its high speed in large
scale simulations. Recent cellular automata models are not able to
avoid flat edges in the result patterns or have large neighborhoods. In
this paper, we present a new model to eliminate flat edges by
minimum number of neighbors.
Abstract: In this study, structural, mechanical, thermal and
electrical properties of poly (lactic acid) (PLA) nanocomposites with
low-loaded (0-1.5 wt%) untreated, heat and nitric acid treated multiwalled
carbon nanotubes (MWCNTs) were studied. Among the
composites, untreated 0.5 wt % MWCNTs and acid-treated 1.0 wt%
MWCNTs reinforced PLA show the tensile strength and modulus
values higher than the others. These two samples along with pure
PLA exhibit the stable orthorhombic α-form, whilst other samples
reveal the less stable orthorhombic β-form, as demonstrated by X-ray
diffraction study. Differential scanning calorimetry reveals the
evolution of the mentioned different phases by controlled cooling and
discloses an enhancement of PLA crystallization by nanotubes
incorporation. Thermogravimetric analysis shows that the MWCNTs
loaded sample degraded faster than PLA. Surface resistivity of the
nanocomposites is found to be dropped drastically by a factor of 1013
with a low loading of MWCNTs (1.5 wt%).
Abstract: The aim of this paper is to investigate twodimensional unsteady flow of a viscous incompressible fluid about stagnation point on permeable stretching sheet in presence of time dependent free stream velocity. Fluid is considered in the influence of transverse magnetic field in the presence of radiation effect. Rosseland approximation is use to model the radiative heat transfer. Using time-dependent stream function, partial differential equations corresponding to the momentum and energy equations are converted into non-linear ordinary differential equations. Numerical solutions of these equations are obtained by using Runge-Kutta Fehlberg method with the help of Newton-Raphson shooting technique. In the present work the effect of unsteadiness parameter, magnetic field parameter, radiation parameter, stretching parameter and the Prandtl number on flow and heat transfer characteristics have been discussed. Skin-friction coefficient and Nusselt number at the sheet are computed and discussed. The results reported in the paper are in good agreement with published work in literature by other researchers.
Abstract: Aim. We have introduced the notion of order to multinormed spaces and countable union spaces and their duals. The topology of bounded convergence is assigned to the dual spaces. The aim of this paper is to develop the theory of ordered topological linear
spaces La,b, L(w, z), the dual spaces of ordered multinormed spaces
La,b, ordered countable union spaces L(w, z), with the topology of bounded convergence assigned to the dual spaces. We apply Laplace transformation to the ordered linear space of Laplace transformable
generalized functions. We ultimately aim at finding solutions to nonhomogeneous
nth order linear differential equations with constant
coefficients in terms of generalized functions and comparing different
solutions evolved out of different initial conditions.
Method. The above aim is achieved by
• Defining the spaces La,b, L(w, z).
• Assigning an order relation on these spaces by identifying a
positive cone on them and studying the properties of the cone.
• Defining an order relation on the dual spaces La,b, L(w, z) of La,b, L(w, z) and assigning a topology to these dual spaces which makes the order dual and the topological dual the same. • Defining the adjoint of a continuous map on these spaces
and studying its behaviour when the topology of bounded
convergence is assigned to the dual spaces.
• Applying the two-sided Laplace Transformation on the ordered
linear space of generalized functions W and studying some
properties of the transformation which are used in solving
differential equations.
Result. The above techniques are applied to solve non-homogeneous
n-th order linear differential equations with constant coefficients in
terms of generalized functions and to compare different solutions of the differential equation.
Abstract: This paper presents the development of an active
vibration control using direct adaptive controller to suppress the
vibration of a flexible beam system. The controller is realized based
on linear parametric form. Differential evolution optimisation
algorithm is used to optimize the controller using single objective
function by minimizing the mean square error of the observed
vibration signal. Furthermore, an alternative approach is developed to
systematically search for the best controller model structure together
with it parameter values. The performance of the control scheme is
presented and analysed in both time and frequency domain.
Simulation results demonstrate that the proposed scheme is able to
suppress the unwanted vibration effectively.
Abstract: The flexible follower response of a translating cam with
four different profiles for rise-dwell-fall-dwell (RDFD) motion is
investigated. The cycloidal displacement motion, the modified
sinusoidal acceleration motion, the modified trapezoidal acceleration
motion, and the 3-4-5 polynomial motion are employed to describe the
rise and the fall motions of the follower and the associated four kinds of
cam profiles are studied. Since the follower flexibility is considered,
the contact point of the roller and the cam is an unknown. Two
geometric constraints formulated to restrain the unknown position are
substituted into Hamilton-s principle with Lagrange multipliers.
Applying the assumed mode method, one can obtain the governing
equations of motion as non-linear differential-algebraic equations. The
equations are solved using Runge-Kutta method. Then, the responses of
the flexible follower undergoing the four different motions are
investigated in time domain and in frequency domain.
Abstract: The steady mixed convection boundary layer flow from
a vertical cone in a porous medium filled with a nanofluid is
numerically investigated using different types of nanoparticles as Cu
(copper), Al2O3 (alumina) and TiO2 (titania). The boundary value
problem is solved by using the shooting technique by reducing it
into an ordinary differential equation. Results of interest for the local
Nusselt number with various values of the constant mixed convection
parameter and nanoparticle volume fraction parameter are evaluated.
It is found that dual solutions exist for a certain range of mixed
convection parameter.
Abstract: Natural convection heat transfer from a heated
horizontal semi-circular cylinder (flat surface upward) has been
investigated for the following ranges of conditions; Grashof number,
and Prandtl number. The governing partial differential equations
(continuity, Navier-Stokes and energy equations) have been solved
numerically using a finite volume formulation. In addition, the role of
the type of the thermal boundary condition imposed at cylinder
surface, namely, constant wall temperature (CWT) and constant heat
flux (CHF) are explored. Natural convection heat transfer from a
heated horizontal semi-circular cylinder (flat surface upward) has
been investigated for the following ranges of conditions; Grashof
number, and Prandtl number, . The governing partial differential
equations (continuity, Navier-Stokes and energy equations) have
been solved numerically using a finite volume formulation. In
addition, the role of the type of the thermal boundary condition
imposed at cylinder surface, namely, constant wall temperature
(CWT) and constant heat flux (CHF) are explored. The resulting flow
and temperature fields are visualized in terms of the streamline and
isotherm patterns in the proximity of the cylinder. The flow remains
attached to the cylinder surface over the range of conditions spanned
here except that for and ; at these conditions, a separated flow
region is observed when the condition of the constant wall
temperature is prescribed on the surface of the cylinder. The heat
transfer characteristics are analyzed in terms of the local and average
Nusselt numbers. The maximum value of the local Nusselt number
always occurs at the corner points whereas it is found to be minimum
at the rear stagnation point on the flat surface. Overall, the average
Nusselt number increases with Grashof number and/ or Prandtl
number in accordance with the scaling considerations. The numerical
results are used to develop simple correlations as functions of
Grashof and Prandtl number thereby enabling the interpolation of the
present numerical results for the intermediate values of the Prandtl or
Grashof numbers for both thermal boundary conditions.
Abstract: In this report, an OTA which is used in fully
differential pipelined ADC was described. Using gain-boost
architecture with difference-ended amplifier, this OTA achieve
high-gain and high-speed. Besides, the CMFB circuit is also used, and
some methods are concerned to improve the performance. Then, by
optimization the layout design, OTA-s mismatch was reduced. This
design was using TSMC 0.18um CMOS process and simulation both
schematic and layout in Cadence. The result of the simulation shows
that the OTA has a gain up to 80dB,a unity gain bandwidth of about
1.437GHz for a 2pF load, a slew rate is about 428V/μs, a output swing
is 0.2V~1.35V, with the power supply of 1.8V, the power
consumption is 88mW. This amplifier was used in a 10bit 150MHz
pipelined ADC.
Abstract: In this paper, we study a new modified Novikov equation for its classical and nonclassical symmetries and use the symmetries to reduce it to a nonlinear ordinary differential equation (ODE). With the aid of solutions of the nonlinear ODE by using the modified (G/G)-expansion method proposed recently, multiple exact traveling wave solutions are obtained and the traveling wave solutions are expressed by the hyperbolic functions, trigonometric functions and rational functions.
Abstract: The group invariant solution for Prandtl-s boundary layer equations for an incompressible fluid governing the flow in radial free, wall and liquid jets having finite fluid velocity at the orifice are investigated. For each jet a symmetry is associated with the conserved vector that was used to derive the conserved quantity for the jet elsewhere. This symmetry is then used to construct the group invariant solution for the third-order partial differential equation for the stream function. The general form of the group invariant solution for radial jet flows is derived. The general form of group invariant solution and the general form of the similarity solution which was obtained elsewhere are the same.
Abstract: In this paper, a class of impulsive BAM fuzzy cellular neural networks with distributed delays and reaction-diffusion terms is formulated and investigated. By employing the delay differential inequality and inequality technique developed by Xu et al., some sufficient conditions ensuring the existence, uniqueness and global exponential stability of equilibrium point for impulsive BAM fuzzy cellular neural networks with distributed delays and reaction-diffusion terms are obtained. In particular, the estimate of the exponential convergence rate is also provided, which depends on system parameters, diffusion effect and impulsive disturbed intention. It is believed that these results are significant and useful for the design and applications of BAM fuzzy cellular neural networks. An example is given to show the effectiveness of the results obtained here.