Abstract: Background: Maintaining the correct body balance is
essential in the prevention of falls in the elderly, which is especially
important for women because of postmenopausal osteoporosis and
the serious consequences of falls. One of the exercise methods which
is very popular among adults, and which may affect body balance in
the positive way is the Pilates method. The aim of the study was to
evaluate the effect of regular Pilates exercises on the ability to
maintain body balance in static conditions in adult healthy women.
Material and methods: The study group consisted of 20 healthy
women attending Pilates twice a week for at least 1 year. The control
group consisted of 20 healthy women physically inactive. Women in
the age range from 35 to 50 years old without pain in musculoskeletal
system or other pain were only qualified to the groups. Body balance
was assessed using MatScan VersaTek platform with Sway Analysis
Module based on Matscan Clinical 6.7 software (Tekscan Inc.,
U.S.A). The balance was evaluated under the following conditions:
standing on both feet with eyes open, standing on both feet with eyes
closed, one-leg standing (separately on the right and left foot) with
eyes open. Each test lasted 30 seconds. The following parameters
were calculated: estimated size of the ellipse of 95% confidence, the
distance covered by the Center of Gravity (COG), the size of the
maximum shift in the sagittal and frontal planes and load distribution
between the left and right foot, as well as between rear- and forefoot.
Results: It was found that there is significant difference between the
groups in favor of the study group in the size of the confidence
ellipse and maximum shifts of COG in the sagittal plane during
standing on both feet, both with the eyes open and closed (p
Abstract: Introduction: Whole-Body Vibration (WBV) uses
high frequency mechanical stimuli generated by a vibration plate and
transmitted through bone, muscle and connective tissues to the whole
body. Research has shown that long-term vibration-plate training
improves neuromuscular facilitation, especially in afferent neural
pathways, responsible for the conduction of vibration and
proprioceptive stimuli, muscle function, balance and proprioception.
Some researchers suggest that the vibration stimulus briefly inhibits
the conduction of afferent signals from proprioceptors and can
interfere with the maintenance of body balance. The aim of this study
was to evaluate the influence of a single set of exercises associated
with whole-body vibration on the joint position sense and body
balance. Material and methods: The study enrolled 55 people aged
19-24 years. These individuals were randomly divided into a test
group (30 persons) and a control group (25 persons). Both groups
performed the same set of exercises on a vibration plate. The
following vibration parameters: frequency of 20Hz and amplitude of
3mm, were used in the test group. The control group performed
exercises on the vibration plate while it was off. All participants were
instructed to perform six dynamic exercises lasting 30 seconds each
with a 60-second period of rest between them. The exercises involved
large muscle groups of the trunk, pelvis and lower limbs.
Measurements were carried out before and immediately after
exercise. Joint position sense (JPS) was measured in the knee joint
for the starting position at 45° in an open kinematic chain. JPS error
was measured using a digital inclinometer. Balance was assessed in a
standing position with both feet on the ground with the eyes open and
closed (each test lasting 30 sec). Balance was assessed using Matscan
with FootMat 7.0 SAM software. The surface of the ellipse of
confidence and front-back as well as right-left swing were measured
to assess balance. Statistical analysis was performed using Statistica
10.0 PL software. Results: There were no significant differences
between the groups, both before and after the exercise (p> 0.05). JPS
did not change in both the test (10.7° vs. 8.4°) and control groups
(9.0° vs. 8.4°). No significant differences were shown in any of the
test parameters during balance tests with the eyes open or closed in
both the test and control groups (p> 0.05). Conclusions: 1.
Deterioration in proprioception or balance was not observed
immediately after the vibration stimulus. This suggests that vibrationinduced
blockage of proprioceptive stimuli conduction can have only
a short-lasting effect that occurs only as long as a vibration stimulus
is present. 2. Short-term use of vibration in treatment does not impair
proprioception and seems to be safe for patients with proprioceptive
impairment. 3. These results need to be supplemented with an
assessment of proprioception during the application of vibration
stimuli. Additionally, the impact of vibration parameters used in the
exercises should be evaluated.
Abstract: The purposes of hydraulic gate are to maintain the
functions of storing and draining water. It bears long-term hydraulic
pressure and earthquake force and is very important for reservoir and
waterpower plant. The high tensile strength of steel plate is used as
constructional material of hydraulic gate. The cracks and rusts,
induced by the defects of material, bad construction and seismic
excitation and under water respectively, thus, the mechanics
phenomena of gate with crack are probing into the cause of stress
concentration, induced high crack increase rate, affect the safety and
usage of hydroelectric power plant. Stress distribution analysis is a
very important and essential surveying technique to analyze
bi-material and singular point problems. The finite difference
infinitely small element method has been demonstrated, suitable for
analyzing the buckling phenomena of welding seam and steel plate
with crack. Especially, this method can easily analyze the singularity
of kink crack. Nevertheless, the construction form and deformation
shape of some gates are three-dimensional system. Therefore, the
three-dimensional Digital Image Correlation (DIC) has been
developed and applied to analyze the strain variation of steel plate with
crack at weld joint. The proposed Digital image correlation (DIC)
technique is an only non-contact method for measuring the variation of
test object. According to rapid development of digital camera, the cost
of this digital image correlation technique has been reduced.
Otherwise, this DIC method provides with the advantages of widely
practical application of indoor test and field test without the restriction
on the size of test object. Thus, the research purpose of this research is
to develop and apply this technique to monitor mechanics crack
variations of weld steel hydraulic gate and its conformation under
action of loading. The imagines can be picked from real time
monitoring process to analyze the strain change of each loading stage.
The proposed 3-Dimensional digital image correlation method,
developed in the study, is applied to analyze the post-buckling
phenomenon and buckling tendency of welded steel plate with crack.
Then, the stress intensity of 3-dimensional analysis of different
materials and enhanced materials in steel plate has been analyzed in
this paper. The test results show that this proposed three-dimensional
DIC method can precisely detect the crack variation of welded steel
plate under different loading stages. Especially, this proposed DIC
method can detect and identify the crack position and the other flaws
of the welded steel plate that the traditional test methods hardly detect
these kind phenomena. Therefore, this proposed three-dimensional
DIC method can apply to observe the mechanics phenomena of
composite materials subjected to loading and operating.
Abstract: Botanical gardens are very significant organizations
which protect the environment against the increasing environmental
problems, provide environmental education for people, offer
recreation possibilities, etc. This article describes botanical gardens
and their functions. The most important function of botanical garden
is to provide environmental education for people and improve
environmental awareness. Considering this function, some botanical
gardens were examined and opinions were suggested about the
subject.
Abstract: Foundation differential settlement and supported
structure tilting are an occasionally occurred engineering problem.
This may be caused by overloading, changes in ground soil properties
or unsupported nearby excavations. Engineering thinking points
directly toward the logic solution for such problem by uplifting the
settled side. This can be achieved with deep foundation elements
such as micro-piles and macro-piles™, jacked piers, and helical piers,
jet grouted mortar columns, compaction grout columns, cement
grouting or with chemical grouting, or traditional pit underpinning
with concrete and mortar. Although, some of these techniques offer
economic, fast and low noise solutions, many of them are quite the
contrary. For tilted structures, with the limited inclination, it may be much
easier to cause a balancing settlement on the less-settlement side
which shall be done carefully in a proper rate. This principal has been
applied in Leaning Tower of Pisa stabilization with soil extraction
from the ground surface. In this research, the authors attempt to
introduce a new solution with a different point of view. So, the
micro-tunneling technique is presented in here as an intended ground
deformation cause. In general, micro-tunneling is expected to induce
limited ground deformations. Thus, the researchers propose to apply
the technique to form small size ground unsupported holes to produce
the target deformations. This shall be done in four phases: 1.
Application of one or more micro-tunnels, regarding the existing
differential settlement value, under the raised side of the tilted
structure. 2. For each individual tunnel, the lining shall be pulled out
from both sides (from jacking and receiving shafts) in the slow rate.
3. If required, according to calculations and site records, an additional
surface load can be applied on the raised foundation side. 4. Finally, a
strengthening soil grouting shall be applied for stabilization after
adjustment. A finite element based numerical model is presented to simulate
the proposed construction phases for different tunneling positions and
tunnels group. For each case, the surface settlements are calculated
and induced plasticity points are checked. These results show the
impact of the suggested procedure on the tilted structure and its
feasibility. Comparing results also show the importance of the
position selection and tunnels group gradual effect. Thus, a new
engineering solution is presented to one of the structural and
geotechnical engineering challenges.
Abstract: The education sector is constantly faced with rapid
changes in technologies in terms of ensuring that the curriculum is up
to date and in terms of making sure that students are aware of these
technological changes. This challenge can be seen as the motivation
for this study, which is to examine the factors affecting computing
students’ awareness of the latest Information Technologies (ICTs).
The aim of this study is divided into two sub-objectives which are:
the selection of relevant theories and the design of a conceptual
model to support it as well as the empirical testing of the designed
model. The first objective is achieved by a review of existing
literature on technology adoption theories and models. The second
objective is achieved using a survey of computing students in the four
universities of the KwaZulu-Natal province of South Africa. Data
collected from this survey is analyzed using Statistical package for
the Social Science (SPSS) using descriptive statistics, ANOVA and
Pearson correlations. The main hypothesis of this study is that there is
a relationship between the demographics and the prior conditions of
the computing students and their awareness of general ICT trends and
of Digital Switch Over (DSO) a new technology which involves the
change from analog to digital television broadcasting in order to
achieve improved spectrum efficiency. The prior conditions of the
computing students that were considered in this study are students’
perceived exposure to career guidance and students’ perceived
curriculum currency. The results of this study confirm that gender,
ethnicity, and high school computing course affect students’
perceived curriculum currency while high school location affects
students’ awareness of DSO. The results of this study also confirm
that there is a relationship between students prior conditions and their
awareness of general ICT trends and DSO in particular.
Abstract: A retrospective study conducted at Christian Medical
College (CMC) Teaching Hospital, Vellore, India on 14th August
2014 to assess the accuracy of clinically estimated foetal weight upon
labour admission. Estimating foetal weight is a crucial factor in
assessing maternal and foetal complications during and after labour.
Medical notes of ninety-eight postnatal women who fulfilled the
inclusion criteria were studied to evaluate the correlation between
their recorded Estimated Foetal Weight (EFW) on admission and
actual birth weight (ABW) of the newborn after delivery. Data
concerning maternal and foetal demographics was also noted.
Accuracy was determined by absolute percentage error and
proportion of estimates within 10% of ABW. Actual birth weights
ranged from 950-4080g. A strong positive correlation between EFW
and ABW (r=0.904) was noted. Term deliveries (≥40 weeks) in the
normal weight range (2500-4000g) had a 59.5% estimation accuracy
(n=74) compared to pre-term (4000g) were underestimated by 25% (n=3) and low birthweight
(LBW) babies were overestimated by 12.7% (n=9). Registrars who
estimated foetal weight were accurate in babies within normal weight
ranges. However, there needs to be an improvement in predicting
weight of macrosomic and LBW foetuses. We have suggested the use
of an amended version of the Johnson’s formula for the Indian
population for improvement and a need to re-audit once
implemented.
Abstract: The laser-ultrasonic method is realized for
quantifying the influence of porosity on the local Young’s
modulus of isotropic composite materials. The method is based on
a laser thermooptical method of ultrasound generation combined
with measurement of the phase velocity of longitudinal and shear
acoustic waves in samples. The main advantage of this method
compared with traditional ultrasonic research methods is the
efficient generation of short and powerful probing acoustic pulses
required for reliable testing of ultrasound absorbing and
scattering heterogeneous materials. Using as an example samples
of a metal matrix composite with reinforcing microparticles of
silicon carbide in various concentrations, it is shown that to
provide an effective increase in Young’s modulus with increasing
concentration of microparticles, the porosity of the final sample
should not exceed 2%.
Abstract: As computing technology advances, smartphone
applications can assist student learning in a pervasive way. For
example, the idea of using mobile apps for the PA Common Trees,
Pests, Pathogens, in the field as a reference tool allows middle school
students to learn about trees and associated pests/pathogens without
bringing a textbook. While working on the development of three heterogeneous mobile
apps, we ran into numerous challenges. Both the traditional waterfall
model and the more modern agile methodologies failed in practice.
The waterfall model emphasizes the planning of the duration for each
phase. When the duration of each phase is not consistent with the
availability of developers, the waterfall model cannot be employed.
When applying Agile Methodologies, we cannot maintain the high
frequency of the iterative development review process, known as
‘sprints’. In this paper, we discuss the challenges and solutions. We
propose a hybrid model known as the Relay Race Methodology to
reflect the concept of racing and relaying during the process of
software development in practice. Based on the development project,
we observe that the modeling of the relay race transition between any
two phases is manifested naturally. Thus, we claim that the RRM
model can provide a de fecto rather than a de jure basis for the core
concept in the software development model. In this paper, the background of the project is introduced first.
Then, the challenges are pointed out followed by our solutions.
Finally, the experiences learned and the future works are presented.
Abstract: Large-scale machine tools for the manufacturing of
large work pieces, e.g. blades, casings or gears for wind turbines,
feature pose-dependent dynamic behavior. Small structural damping
coefficients lead to long decay times for structural vibrations that
have negative impacts on the production process. Typically, these
vibrations are handled by increasing the stiffness of the structure by
adding mass. This is counterproductive to the needs of sustainable
manufacturing as it leads to higher resource consumption both in
material and in energy. Recent research activities have led to higher
resource efficiency by radical mass reduction that is based on controlintegrated
active vibration avoidance and damping methods. These
control methods depend on information describing the dynamic
behavior of the controlled machine tools in order to tune the
avoidance or reduction method parameters according to the current
state of the machine. This paper presents the appearance, consequences and challenges
of the pose-dependent dynamic behavior of lightweight large-scale
machine tool structures in production. It starts with the theoretical
introduction of the challenges of lightweight machine tool structures
resulting from reduced stiffness. The statement of the pose-dependent
dynamic behavior is corroborated by the results of the experimental
modal analysis of a lightweight test structure. Afterwards, the
consequences of the pose-dependent dynamic behavior of lightweight
machine tool structures for the use of active control and vibration
reduction methods are explained. Based on the state of the art of
pose-dependent dynamic machine tool models and the modal
investigation of an FE-model of the lightweight test structure, the
criteria for a pose-dependent model for use in vibration reduction are
derived. The description of the approach for a general posedependent
model of the dynamic behavior of large lightweight
machine tools that provides the necessary input to the aforementioned
vibration avoidance and reduction methods to properly tackle
machine vibrations is the outlook of the paper.
Abstract: This paper is meant to analyze the ranking of
University of Malaysia Terengganu, UMT’s website in the World
Wide Web. There are only few researches have been done on
comparing the ranking of universities’ websites so this research will
be able to determine whether the existing UMT’s website is serving
its purpose which is to introduce UMT to the world. The ranking is
based on hub and authority values which are accordance to the
structure of the website. These values are computed using two websearching
algorithms, HITS and SALSA. Three other universities’
websites are used as the benchmarks which are UM, Harvard and
Stanford. The result is clearly showing that more work has to be done
on the existing UMT’s website where important pages according to
the benchmarks, do not exist in UMT’s pages. The ranking of UMT’s
website will act as a guideline for the web-developer to develop a
more efficient website.
Abstract: Excessive fretting wear at the taper-trunnion junction
(trunnionosis) apparently contributes to the high failure rates of hip
implants. Implant wear and corrosion lead to the release of metal
particulate debris and subsequent release of metal ions at the tapertrunnion
surface. This results in a type of metal poisoning referred to
as metallosis. The consequences of metal poisoning include;
osteolysis (bone loss), osteoarthritis (pain), aseptic loosening of the
prosthesis and revision surgery. Follow up after revision surgery,
metal debris particles are commonly found in numerous locations. Background: A stable connection between the femoral ball head
(taper) and stem (trunnion) is necessary to prevent relative motions
and corrosion at the taper junction. Hence, the importance of
component assembly cannot be over-emphasized. Therefore, the aim
of this study is to determine the influence of head-stem junction
assembly by press fitting and the subsequent
disengagement/disassembly on the connection strength between the
taper ball head and stem. Methods: CoCr femoral heads were assembled with High stainless
hydrogen steel stem (trunnion) by Push-in i.e. press fit; and
disengaged by pull-out test. The strength and stability of the two
connections were evaluated by measuring the head pull-out forces
according to ISO 7206-10 standards. Findings: The head-stem junction strength linearly increases with
assembly forces.
Abstract: Polycyclic Aromatic Hydrocarbons (PAHs) are
formed mainly because of incomplete combustion of organic
materials during industrial, domestic activities or natural occurrence.
Their toxicity and contamination of terrestrial and aquatic ecosystem
have been established. However, with limited validity index, previous
research has focused on PAHs isomer pair ratios of variable
physicochemical properties in source identification. The objective of
this investigation was to determine the empirical validity of Pearson
Correlation Coefficient (PCC) and Cluster Analysis (CA) in PAHs
source identification along soil samples of different land uses.
Therefore, 16 PAHs grouped, as Endocrine Disruption Substances
(EDSs) were determined in 10 sample stations in top and sub soils
seasonally. PAHs was determined the use of Varian 300 gas
chromatograph interfaced with flame ionization detector. Instruments
and reagents used are of standard and chromatographic grades
respectively. PCC and CA results showed that the classification of
PAHs along pyrolitic and petrogenic organics used in source
signature is about the predominance PAHs in environmental matrix.
Therefore, the distribution of PAHs in the studied stations revealed
the presence of trace quantities of the vast majority of the sixteen
PAHs, which may ultimately inhabit the actual source signature
authentication. Therefore, factors to be considered when evaluating
possible sources of PAHs could be; type and extent of bacterial
metabolism, transformation products/substrates, and environmental
factors such as salinity, pH, oxygen concentration, nutrients, light
intensity, temperature, co-substrates, and environmental medium are
hereby recommended as factors to be considered when evaluating
possible sources of PAHs.
Abstract: Novel wind-lens turbine designs can augment power
output. Vacuum-Assisted Resin Transfer Molding (VARTM) is used
to form large and complex structures from a Carbon Fiber Reinforced
Polymer (CFRP) composite. Typically, wind-lens turbine structures
are fabricated in segments, and then bonded to form the final structure.
This paper introduces five new adhesive joints, divided into two
groups: one is constructed between dry carbon and CFRP fabrics, and
the other is constructed with two dry carbon fibers. All joints and
CFRP fabrics were made in our laboratory using VARTM
manufacturing techniques. Specimens were prepared for tensile testing
to measure joint performance. The results showed that the second
group of joints achieved a higher tensile strength than the first group.
On the other hand, the tensile fracture behavior of the two groups
showed the same pattern of crack originating near the joint ends
followed by crack propagation until fracture.
Abstract: Well logging records can help to answer many
questions from a wide range of special interested information and
basic petrophysical properties to formation evaluation of oil and gas
reservoirs. The accurate calculations of porosity in carbonate
reservoirs are the most challenging aspects of the well logging
analysis. Many equations have been developed over the years based
on known physical principles or on empirically derived relationships,
which are used to calculate porosity, estimate lithology, and water
saturation; however these parameters are calculated from well logs by
using modern technique in a current study. Nasiriya oil field is one of
the giant oilfields in the Middle East, and the formation under study
is the Mishrif carbonate formation which is the shallowest
hydrocarbon bearing zone in this oilfield. Neurolog software was
used to digitize the scanned copies of the available logs.
Environmental corrections had been made as per Schlumberger charts
2005, which supplied in the Interactive Petrophysics software. Three
saturation models have been used to calculate water saturation of
carbonate formations, which are simple Archie equation, Dual water
model, and Indonesia model. Results indicate that the Mishrif
formation consists mainly of limestone, some dolomite, and shale.
The porosity interpretation shows that the logging tools have a good
quality after making the environmental corrections. The average
formation water saturation for Mishrif formation is around 0.4-
0.6.This study is provided accurate behavior of petrophysical
properties with depth for this formation by using modern software.
Abstract: This study aimed to 1) develop pre-service teachers’
leadership skills through camp-based learning, and 2) develop preservice
teachers’ teamwork skills through camp-based learning. An
applied research methodology was used. The target group was
derived from a purposive selection. It involved 32 fourth-year
students in Early Childhood Education Program enrolling a course
entitled Seminar in Early Childhood Education provided during
second semester of academic year 2013. The treatment was camp-based
learning activities which applied a PDCA process including
four stages: 1) plan, 2) do, 3) check, and 4) act. Research instruments
were a learning camp program, a camp-based learning management
plan, a 5-level assessment form for leadership skills and a 5-level
assessment form for assessing teamwork skills. Data were analyzed
using descriptive statistics. Results were: 1) pre-service teachers’
leadership skills yielded the before treatment average score at x= 3.4,
S.D.=0.6 2and the after-treatment average score at x 4.29 , S.D.=0.66
pre-service teachers’ teamwork skills yielded the before-treatment
average score at x=3.31, S.D.=0.60 and the after-treatment average
score at x=4.42, S.D.=0.66 Both differences were statistically
significant at the .05 level. Thus, the pre-service teachers’ leadership
and teamwork skills were significantly improved through the camp-based
learning approach.
Abstract: The importance of agribusiness development is
proved in accordance with the trends in the agricultural sector of
Georgia. Agribusiness environment and the consequences of the
agricultural reforms are evaluated. The factors hindering the
development of agribusiness are revealed and the ways for
overcoming these problems are suggested. SWOT analysis is done in
order to identify the needs of agribusiness. The needs of agribusiness
development in Georgia are evaluated by priorities: prevention of
diseases and reduction of the harm caused by these diseases,
accessibility of long-term agricultural loans with low interest rates,
improving qualification of farmers, the level of education and usage
of modern technologies, changes in legislation, accessibility to high
quality agricultural machinery, and the development of infrastructure.
Based on the outcomes of the research, agribusiness development
strategies in Georgia are suggested and appropriate priorities of
economic policy are determined. Conclusions are made and based on
these conclusions, some recommendations are suggested.
Abstract: This investigation is focused on using of Mon dance
in Pathum Thani Province’s tradition and has the following
objectives: 1) to study the background of Mon dance in Pathum
Thani Province; 2) to study Mon dance in Pathum Thani Province;
and 3) to study of using Mon dance in Pathum Thani province’s
tradition. This qualitative research was conducted in Pathum Thani
province (in the central of Thailand). Data was collected from
documentary study and field data by means of observation, interview,
and group discussion. Workshops were also held with a total of 100
attendees, comprised of 20 key informants, 40 casual informants and
40 general informants. Data was validated using the triangulation
technique and the findings are presented using the descriptive
analysis. The results of the study show that the historical background
of Mon dance in Pathum Thani Province initiated during the war
evacuation from Martaban (south of Burma) to settle down in Sam
Khok, Pathum Thani Province in Ayutthaya period to Rattanakosin.
The study found that Mon dance typically consists of 12-13 dancing
process. The melodies have 12-13 songs. Piphat Mon (Mon
traditional music ensemble) is used in the performance. Performers
are dressed in Mon traditional costumes. The performers are 6-12
women and depending on the employer’s demands. Length of the
performance varies from the duration of music orchestration. Rituals
and customs performed are paying homage to teachers before the
performance. The offerings are composed of flowers, incense sticks,
candles, money gifts which are well arranged on a tray with pedestal,
and also liquors, tobaccos and pure water for asking propitiousness.
For the use of Mon dance in Pathum Thani Province’s tradition, it is
found that the dance is commonly performed in the funeral
ceremonial tradition at present because the physical postures of the
performance are considered graceful and exquisite. In addition, as for
its value, it has long been believed since the ancient times that Mon
dance was a sacred thing considered as the dignity and glorification
especially for funeral ceremonies of priest or royal hierarchy classes.
However, Mon dance has continued to be used in the traditions
associated with Mon people activities in Pathum Thani Province for
instance customary welcome for honor guest and Songkran festival.
Abstract: Targeted drug delivery is a method of delivering
medication to a patient in a manner that increases the concentration
of the medication in some parts of the body relative to others.
Targeted drug delivery seeks to concentrate the medication in the
tissues of interest while reducing the relative concentration of the
medication in the remaining tissues. This improves efficacy of the
while reducing side effects. In the present work, we investigate the
effect of magnetic field, flow rate and particle concentration on the
capturing of magnetic particles transported in a stent implanted
fluidic channel. Iron oxide magnetic nanoparticles (Fe3O4)
nanoparticles were synthesized via co-precipitation method. The
synthesized Fe3O4 nanoparticles were added in the de-ionized (DI)
water to prepare the Fe3O4 magnetic particle suspended fluid. This
fluid is transported in a cylindrical tube of diameter 8 mm with help
of a peristaltic pump at different flow rate (25-40 ml/min). A
ferromagnetic coil of SS 430 has been implanted inside the
cylindrical tube to enhance the capturing of magnetic nanoparticles
under magnetic field. The capturing of magnetic nanoparticles was
observed at different magnetic magnetic field, flow rate and particle
concentration. It is observed that capture efficiency increases from
47-67% at magnetic field 2-5kG, respectively at particle
concentration 0.6mg/ml and at flow rate 30 ml/min. However, the
capture efficiency decreases from 65 to 44% by increasing the flow
rate from 25 to 40 ml/min, respectively. Furthermore, it is observed
that capture efficiency increases from 51 to 67% by increasing the
particle concentration from 0.3 to 0.6 mg/ml, respectively.
Abstract: The aim of the study is to improve the understanding
of latent and sensible thermal energy storage within a paraffin wax
media by an array of cylindrical tubes arranged both in in-line and
staggered layouts. An analytical and experimental study is carried out
in a horizontal shell-and-tube type system during melting process.
Pertamina paraffin-wax was used as a phase change material (PCM),
while the tubes are embedded in the PCM. From analytical study we
can obtain the useful information in designing a thermal energy
storage such as: the motion of interface, amount of material melted at
any time in the process, and the heat storage characteristic during
melting. The use of staggered tubes is proposed compared to in-line
layout in a heat exchanger as thermal storage. The experimental study
is used to verify the validity of the analytical predictions. From the
comparisons, the analytical and experimental data are in a good
agreement.