Abstract: Composite material based on Fe3Si micro-particles
and Mn-Zn nano-ferrite was prepared using powder metallurgy
technology. The sol-gel followed by autocombustion process was
used for synthesis of Mn0.8Zn0.2Fe2O4 ferrite. 3 wt.% of mechanically
milled ferrite was mixed with Fe3Si powder alloy. Mixed micro-nano
powder system was homogenized by the Resonant Acoustic Mixing
using ResodynLabRAM Mixer. This non-invasive homogenization
technique was used to preserve spherical morphology of Fe3Si
powder particles. Uniaxial cold pressing in the closed die at pressure
600 MPa was applied to obtain a compact sample. Microwave
sintering of green compact was realized at 800°C, 20 minutes, in air.
Density of the powders and composite was measured by
Hepycnometry. Impulse excitation method was used to measure
elastic properties of sintered composite. Mechanical properties were
evaluated by measurement of transverse rupture strength (TRS) and
Vickers hardness (HV). Resistivity was measured by 4 point probe
method. Ferrite phase distribution in volume of the composite was
documented by metallographic analysis.
It has been found that nano-ferrite particle distributed among
micro- particles of Fe3Si powder alloy led to high relative density
(~93%) and suitable mechanical properties (TRS >100 MPa, HV
~1GPa, E-modulus ~140 GPa) of the composite. High electric
resistivity (R~6.7 ohm.cm) of prepared composite indicate their
potential application as soft magnetic material at medium and high
frequencies.
Abstract: The aim of this study was to select the best strains of
Saccharomyces cerevisiae able to resist lead and cadmium. Ten
strains were screened on the basis of their resistance at different
concentrations of 0, 2, 4, 8, 12, 16, 20 and 24 ppm for Pb and 0, 0.5,
1, 2, 4, 6, 8 and 10 ppm for Cd. The properties of baker's yeast
quality were decreased by the increase of Pb or Cd in growth
medium. The slope values of yield, total viable cells and gassing
power of produced baker's yeast were investigated as an indicator of
metal resistant. In addition, concentrations of Pb and Cd in produced
baker's yeast were determined. The strain of S. cerevisiae FH-620
had the highest resistance against Pb and Cd and had the minimum
levels of both two investigated metals in produced baker's yeast.
Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: This work reports the potential of using Palm Kernel
(PK) ash and shell as a partial substitute for Portland Cement (PC)
and coarse aggregate in the development of mortar and concrete. PK
ash and shell are agro-waste materials from palm oil mills, the
disposal of PK ash and shell is an environmental problem of concern.
The PK ash has pozzolanic properties that enables it as a partial
replacement for cement and also plays an important role in the
strength and durability of concrete, its use in concrete will alleviate
the increasing challenges of scarcity and high cost of cement. In order
to investigate the PC replacement potential of PK ash, three types of
PK ash were produced at varying temperature (350-750C) and they
were used to replace up to 50% PC. The PK shell was used to replace
up to 100% coarse aggregate in order to study its aggregate
replacement potential. The testing programme included material
characterisation, the determination of compressive strength, tensile
splitting strength and chemical durability in aggressive sulfatebearing
exposure conditions. The 90 day compressive results showed
a significant strength gain (up to 26.2 N/mm2). The Portland cement
and conventional coarse aggregate has significantly higher influence
in the strength gain compared to the equivalent PK ash and PK shell.
The chemical durability results demonstrated that after a prolonged
period of exposure, significant strength losses in all the concretes
were observed. This phenomenon is explained, due to lower change
in concrete morphology and inhibition of reaction species and the
final disruption of the aggregate cement paste matrix.
Abstract: The development of the United Arab Emirates (UAE)
into a regional trade, tourism, finance and logistics hub has
transformed its real estate markets. However, speculative activity and
price volatility remain concerns. UAE residential market values
(MV) are exposed to fluctuations in capital flows and migration
which, in turn, are affected by geopolitical uncertainty, oil price
volatility and global investment market sentiment. Internally, a
complex interplay between administrative boundaries, land tenure,
building quality and evolving location characteristics fragments UAE
residential property markets. In short, the UAE Residential Valuation
System (UAE-RVS) confronts multiple challenges to collect, filter
and analyze relevant information in complex and dynamic spatial and
capital markets. A robust (RVS) can mitigate the risk of unhelpful
volatility, speculative excess or investment mistakes. The research
outlines the institutional, ontological, dynamic and epistemological
issues at play. We highlight the importance of system capabilities,
valuation standard salience and stakeholders trust.
Abstract: In this study, we have focused our attention on
combining of molecular imprinting into nanofilms and QCM
nanosensor approaches and producing QCM nanosensor for anti-
CCP, chosen as model protein, using anti-CCP imprinted nanofilms.
The nonimprinted nanosensor was also prepared to evaluate the
selectivity of the imprinted nanosensor. Anti-CCP imprinted QCM
nanosensor was tested for real time detection of anti-CCP from
aqueous solution. The kinetic and affinity studies were determined by
using anti-CCP solutions with different concentrations. The
responses related with mass shifts (%m) and frequency shifts (%f)
were used to evaluate adsorption properties. To show the selectivity
of the anti-CCP imprinted QCM nanosensor, competitive adsorption
of anti-CCP and IgM was investigated. The results indicate that anti-
CCP imprinted QCM nanosensor has higher adsorption capabilities
for anti-CCP than for IgM, due to selective cavities in the polymer
structure.
Abstract: Environmental impact assessment techniques have
been developed as a result of the worldwide efforts to reduce the
environmental impact of global warming. By using the quantification
method in the construction industry, it is now possible to manage the
greenhouse gas is to systematically evaluate the impact on the
environment over the entire construction process. In particular, the
proportion of greenhouse gas emissions at the production stage of
construction material occupied is high, and efforts are needed in
particular in the construction field.
In this research, intended for concrete products for the construction
materials, by using the LCA method, we compared the results of
environmental impact assessment and carbon emissions of developing
products that have been applied low-carbon technologies compared to
existing products. As a results, by introducing a raw material of
industrial waste, showed carbon reduction. Through a comparison of
the carbon emission reduction effect of low carbon technologies, it is
intended to provide academic data for the evaluation of greenhouse
gases in the construction sector and the development of low carbon
technologies of the future.
Abstract: In rapid industrial development, the demand for
high-strength and lightweight materials have been increased. Thus,
various CFRP (Carbon Fiber Reinforced Plastics) with composite
materials are being used. The design variables of CFRP are its
lamination direction, order and thickness. Thus, the hardness and
strength of CFRP depends much on their design variables. In this
paper, the lamination direction of CFRP was used to produce a
symmetrical ply [0°/0°, -15°/+15°, -30°/+30°, -45°/+45°, -60°/+60°,
-75°/+75° and 90°/90°] and an asymmetrical ply [0°/15°, 0°/30°,
0°/45°, 0°/60° 0°/75° and 0°/90°]. The bending flexure stress of the
CFRP specimen was evaluated through a bending test. Its thermal
property was measured using an infrared camera. The symmetrical
specimen and the asymmetrical specimen were analyzed. The results
showed that the asymmetrical specimen increased the bending loads
according to the increase in the orientation angle; and from 0°, the
symmetrical specimen showed a tendency opposite the asymmetrical
tendency because the tensile force of fiber differs at the vertical
direction of its load. Also, the infrared camera showed that the thermal
property had a trend similar to that of the mechanical properties.
Abstract: Collection of storm water runoff and forcing it into the
groundwater is the need of the hour to sustain the ground water table.
However, the runoff entraps various types of sediments and other
floating objects whose removal are essential to avoid pollution of
ground water and blocking of pores of aquifer. However, it requires
regular cleaning and maintenance due to problem of clogging. To
evaluate the performance of filter system consisting of coarse sand
(CS), gravel (G) and pebble (P) layers, a laboratory experiment was
conducted in a rectangular column. The effect of variable thickness
of CS, G and P layers of the filtration unit of the recharge shaft on the
recharge rate and the sediment concentration of effluent water were
evaluated.
Medium sand (MS) of three particle sizes, viz. 0.150–0.300 mm
(T1), 0.300–0.425 mm (T2) and 0.425–0.600 mm of thickness 25 cm,
30 cm and 35 cm respectively in the top layer of the filter system and
having seven influent sediment concentrations of 250–3,000 mg/l
were used for experimental study. The performance was evaluated in
terms of recharge rates and clogging time. The results indicated that
100 % suspended solids were entrapped in the upper 10 cm layer of
MS, the recharge rates declined sharply for influent concentrations of
more than 1,000 mg/l. All treatments with higher thickness of MS
media indicated recharge rate slightly more than that of all treatment
with lower thickness of MS media respectively. The performance of
storm water infiltration systems was highly dependent on the
formation of a clogging layer at the filter. An empirical relationship
has been derived between recharge rates, inflow sediment load, size
of MS and thickness of MS with using MLR.
Abstract: This paper seeks to analyse the benefits of big data
and more importantly the challenges it pose to the subject of privacy
and data protection. First, the nature of big data will be briefly
deliberated before presenting the potential of big data in the present
days. Afterwards, the issue of privacy and data protection is
highlighted before discussing the challenges of implementing this
issue in big data. In conclusion, the paper will put forward the debate
on the adequacy of the existing legal framework in protecting
personal data in the era of big data.
Abstract: Biofuels production has come forth as a future
technology to combat the problem of depleting fossil fuels. Bio-based
ethanol production from enzymatic lignocellulosic biomass
degradation serves an efficient method and catching the eye of
scientific community. High cost of the enzyme is the major obstacle
in preventing the commercialization of this process. Thus main
objective of the present study was to optimize composition of
medium components for enhancing cellulase production by newly
isolated strain of Bacillus tequilensis. Nineteen factors were taken
into account using statistical Plackett-Burman Design. The significant
variables influencing the cellulose production were further employed
in statistical Response Surface Methodology using Central
Composite Design for maximizing cellulase production. The
optimum medium composition for cellulase production was: peptone
(4.94 g/L), ammonium chloride (4.99 g/L), yeast extract (2.00 g/L),
Tween-20 (0.53 g/L), calcium chloride (0.20 g/L) and cobalt chloride
(0.60 g/L) with pH 7, agitation speed 150 rpm and 72 h incubation at
37oC. Analysis of variance (ANOVA) revealed high coefficient of
determination (R2) of 0.99. Maximum cellulase productivity of 11.5
IU/ml was observed against the model predicted value of 13 IU/ml.
This was found to be optimally active at 60oC and pH 5.5.
Abstract: In this paper, we have compared and analyzed the
electroabsorption properties between with and without excitonic
effect bulk in high purity GaAs spatial light modulator for optical
fiber communication network. The eletroabsorption properties such
as absorption spectra, change in absorption spectra, change in
refractive index and extinction ration has been calculated. We have
also compared the result of absorption spectra and change in
absorption spectra with the experimental results and found close
agreement with experimental results.
Abstract: This study evaluated the use of raw or processed
Prosopis juliflora (Meskit) pods as a major ingredient in a formulated
ration to provide an alternative non-conventional concentrate for
livestock feeding in Oman. Dry Meskit pods were reduced to lengths
of 0.5- 1.0 cm to ensure thorough mixing into three diets. Meskit
pods were subjected to two types of treatments; roasting and soaking.
They were roasted at 150оC for 30 minutes using a locally-made
roasting device (40 kg barrel container rotated by electric motor and
heated by flame gas cooker). Chopped pods were soaked in tap water
for 24 hours and dried for 2 days under the sun with frequent turning.
The Meskit-pod-based diets (MPBD) were formulated and pelleted
from 500 g/kg ground Meskit pods, 240 g/kg wheat bran, 200 g/kg
barley grain, 50 g/kg local dried sardines and 10 g/kg of salt. Twenty
four 10 months-old intact Omani male lambs with average body
weight of 27.3 kg (± 0.5 kg) were used in a feeding trial for 84 days.
They were divided (on body weight basis) and allocated to four diet
combination groups. These were: Rhodes grass hay (RGH) plus a
general ruminant concentrate (GRC); RGH plus raw Meskit pods
(RMP) based concentrate; RGH plus roasted Meskit pods (ROMP)
based concentrate; RGH plus soaked Meskit pods (SMP) based
concentrate Daily feed intakes and bi-weekly body weights were
recorded. MPBD had higher contents of crude protein (CP), acid
detergent fibre (ADF) and neutral detergent fibre (NDF) than the
GRC. Animals fed various types of MPBD did not show signs of ill
health. There was a significant effect of feeding ROMP on the
performance of Omani sheep compared to RMP and SMP. The
ROMP fed animals had similar performance to those fed the GRC in
terms of feed intake, body weight gain and feed conversion ratio
(FCR).This study indicated that roasted Meskit pods based diet may
be used instead of the commercial concentrate for feeding Omani
sheep without adverse effects on performance. It offers a cheap
alternative source of protein and energy for feeding Omani sheep.
Also, it might help in solving the spread impact of Meskit trees,
maintain the ecosystem and helping in preserving the local tree
species.
Abstract: Qatar, a Gulf country highly dependent on its oil and
gas revenues – is looking to innovate, diversify, and ultimately reach
its aim of creating a knowledge economy to prepare for its post-oil
era. One area that the country is investing in is Contemporary Art,
and world renowned artists such as Damien Hirst and Richard Serra –
have been commissioned to design site-specific art for the public
spaces of the city of Doha as well as in more remote desert locations.
This research discusses the changing presence, role and context of
public art in Doha, both from a historical and cultural overview, and
the different forms and media as well as the typologies of urban and
public spaces in which the art is installed. It examines the process of
implementing site-specific artworks, looking at questions of scale,
history, social meaning and formal aesthetics. The methodologies
combine theoretical research on the understanding of public art and
its role and placement in public space, as well as empirical research
on contemporary public art projects in Doha, based on documentation
and interviews and as well as site and context analysis of the urban or
architectural spaces within which the art is situated. Surveys and
interviews – using social media - in different segments of the
contemporary Qatari society, including all nationalities and social
groups, are used to measure and qualify the impacts and effects on
the population.
Abstract: Macro invertebrates have been used to monitor
organic pollution in rivers and streams. Several biotic indices based
on macro invertebrates have been developed over the years including
the Biological Monitoring Working Party (BMWP). A new biotic
index, the Gammarus:Asellus ratio has been recently proposed as an
index of organic pollution. This study tested the validity of the
Gammarus:Asellus ratio as an index of organic pollution, by
examining the relationship between the Gammarus:Asellus ratio and
physical chemical parameters, and other biotic indices such as
BMWP and, Average Score Per Taxon (ASPT) from lakes and
streams at Markeaton Park, Allestree Park and Kedleston Hall,
Derbyshire. Macro invertebrates were sampled using the standard
five minute kick sampling techniques physical and chemical
environmental variables were obtained based on standard sampling
techniques. Eighteen sites were sampled, six sites from Markeaton
Park (three sites across the stream and three sites across the lake). Six
sites each were also sampled from Allestree Park and Kedleston Hall
lakes. The Gammarus:Asellus ratio showed an opposite significant
positive correlations with parameters indicative of organic pollution
such as the level of nitrates, phosphates, and calcium and also
revealed a negatively significant correlations with other biotic indices
(BMWP/ASPT). The BMWP score correlated positively significantly
with some water quality parameters such as dissolved oxygen and
flow rate, but revealed no correlations with other chemical
environmental variables. The BMWP score was significantly higher
in the stream than the lake in Markeaton Park, also The ASPT scores
appear to be significantly higher in the upper Lakes than the middle
and lower lakes. This study has further strengthened the use of
BMWP/ASPT score as an index of organic pollution. But additional
application is required to validate the use of Gammarus:Asellus as a
rapid bio monitoring tool.
Abstract: Generally the natural environment is made up of air,
water and soil. The release of emission of industrial waste into
anyone of the components of the environment causes pollution.
Industrial pollution significantly threatens the inherent right of
people, to the enjoyment of a safe and secure environment. The aim
of this paper is to assess the effect of environmental pollution and
health risks of residents living near Ewekoro cement factory. The
research made use of IKONOS imagery for Geographical
Information System (GIS) to buffer and extract buildings that are less
than 1km to the factory, within 1km to 5km and above 5km to the
factory. Also questionnaire was used to elicit information on the
socio-economic factors, effect of environmental pollution on
residents and measures adopted to control industrial pollution on the
residents. Findings show that most buildings that fall between less
than 1km and 1km to 5km to the factory have high health risk in the
study area. The study recommended total relocation for the residents
of the study area to reduce health risk problems.
Abstract: Recently, universities are increasingly consuming
energy to support various activities. A large population of staff and
students in Malaysian universities has led to excessive energy
consumption which directly gives an impact to the environment. The
key question then ascended “How well is an energy management
(EM) been practiced in universities without taking the Critical
Success Factors (CSFs) into consideration to ensure the management
of university achieves the goals in reducing energy consumption.
Review on past literature is carried out to establish CSFs for EM best
practices. Thus, this paper highlighted the CSFs which have to be
focused on by management of university to successfully measure the
EM implementation and its performance. At the end of this paper, a
theoretical framework is developed for EM success factors towards
sustainable university.
Abstract: An experiment was conducted to determine the effect
of pollination on seed quality of rapeseed in Chitwan, Nepal during
2012-2013. The experiment was designed in Randomized Complete
Block with four replications and five treatments. The rapeseed plots
were caged with mosquito nets at 10% flowering except natural
pollination. Two-framed colonies of Apis mellifera L. and Apis
cerana F. were introduced separately for pollination, and control plot
caged without pollinators. The highest germination percent was
observed on Apis cerana F. pollinated plot seeds (90.50%
germination) followed by Apis mellifera L. pollinated plots (87.25 %)
and lowest on control plots (42.00% germination) seeds. Similarly,
seed test weight of Apis cerana F. pollinated plots (3.22 gm/ 1000
seed) and Apis mellifera L. pollinated plots (2.93 gm/1000 seed) were
and lowest on control plots (2.26 gm/ 1000 seed) recorded. Likewise,
oil content was recorded highest on pollinated by Apis cerana F.
(36.1%) followed by pollinated by Apis mellifera L. (35.4%) and
lowest on control plots (32.8%). This study clearly indicated
pollination increases the seed quality of rapeseed and therefore,
management of honeybee is necessary for producing higher quality of
rapeseed under Chitwan condition.
Abstract: The concentration levels of six heavy metals (Cd, Cr,
Fe, Ni, Pb and Zn) and two mineral elements (Ca and Mg) were
determined in soil samples collected from the vicinity of two auto
mechanic workshops in Sabon-Gari, Kaduna state, Nigeria, using
Atomic Absorption Spectrometry (AAS), in order to compare the
gradation of their concentrations with distance and depth of soil from
the workshop sites. At site 1, concentrations of Lead, Chromium, Iron
and Zinc were generally found to be above the World Health
Organization limits, while those of Nickel and Cadmium fell within
the limits. Iron had the highest concentration with a range of 176.274
ppm to 489.127 ppm at depths of 5 cm to 15 cm and a distance range
of 5 m to 15 m, while the concentration of cadmium was least with a
range of 0.001 ppm to 0.008 ppm at similar depth and distance
ranges. In addition, there was more of calcium (11.521 ppm to
121.709 ppm), in all the samples, than magnesium (11.293 ppm to
21.635 ppm). Similar results were obtained for site II. The
concentrations of all the metals analyzed showed a downward
gradient with increase in depth and distance from both workshop sites
except for iron and zinc at site 2. The immediate and remote
implications of these findings on the biota are discussed.
Abstract: The legends about “user-friendly” and “easy-to-use”
birotical tools (computer-related office tools) have been spreading
and misleading end-users. This approach has led us to the extremely
high number of incorrect documents, causing serious financial losses
in the creating, modifying, and retrieving processes. Our research
proved that there are at least two sources of this underachievement:
(1) The lack of the definition of the correctly edited, formatted
documents. Consequently, end-users do not know whether their
methods and results are correct or not. They are not aware of their
ignorance. They are so ignorant that their ignorance does not allow
them to realize their lack of knowledge. (2) The end-users’ problem
solving methods. We have found that in non-traditional programming
environments end-users apply, almost exclusively, surface approach
metacognitive methods to carry out their computer related activities,
which are proved less effective than deep approach methods.
Based on these findings we have developed deep approach
methods which are based on and adapted from traditional
programming languages. In this study, we focus on the most popular
type of birotical documents, the text based documents. We have
provided the definition of the correctly edited text, and based on this
definition, adapted the debugging method known in programming.
According to the method, before the realization of text editing, a
thorough debugging of already existing texts and the categorization
of errors are carried out. With this method in advance to real text
editing users learn the requirements of text based documents and also
of the correctly formatted text.
The method has been proved much more effective than the
previously applied surface approach methods. The advantages of the
method are that the real text handling requires much less human and
computer sources than clicking aimlessly in the GUI (Graphical User
Interface), and the data retrieval is much more effective than from
error-prone documents.