Abstract: The measurement of aerodynamic forces and moments
acting on an aircraft model is important for the development of wind
tunnel measurement technology to predict the performance of the full
scale vehicle. The potentials of an aircraft model with and without
winglet and aerodynamic characteristics with NACA wing No. 65-3-
218 have been studied using subsonic wind tunnel of 1 m × 1 m
rectangular test section and 2.5 m long of Aerodynamics Laboratory
Faculty of Engineering (University Putra Malaysia). Focusing on
analyzing the aerodynamic characteristics of the aircraft model, two
main issues are studied in this paper. First, a six component wind
tunnel external balance is used for measuring lift, drag and pitching
moment. Secondly, Tests are conducted on the aircraft model with
and without winglet of two configurations at Reynolds numbers
1.7×105, 2.1×105, and 2.5×105 for different angle of attacks. Fuzzy
logic approach is found as efficient for the representation,
manipulation and utilization of aerodynamic characteristics.
Therefore, the primary purpose of this work was to investigate the
relationship between lift and drag coefficients, with free-stream
velocities and angle of attacks, and to illustrate how fuzzy logic
might play an important role in study of lift aerodynamic
characteristics of an aircraft model with the addition of certain
winglet configurations. Results of the developed fuzzy logic were
compared with the experimental results. For lift coefficient analysis,
the mean of actual and predicted values were 0.62 and 0.60
respectively. The coreelation between actual and predicted values
(from FLS model) of lift coefficient in different angle of attack was
found as 0.99. The mean relative error of actual and predicted valus
was found as 5.18% for the velocity of 26.36 m/s which was found to
be less than the acceptable limits (10%). The goodness of fit of
prediction value was 0.95 which was close to 1.0.
Abstract: This paper studies mixed-mode fracture mechanics in
rock based on experimental and numerical analyses. Experiments
were performed on sharp-cracked specimens using the modified
Arcan specimen test loading device. The modified Arcan specimen
test was, in association with a special loading device, an appropriate
apparatus for experimental mixed-mode fracture analysis. By
varying the loading angle from 0° to 90°, pure mode-I, pure mode-II
and a wide range of mixed-mode data were obtained experimentally.
Using the finite element results, correction factors applied to the
rectangular fracture specimen. By employing experimentally
measured critical loads and the aid of the finite element method,
mixed-mode fracture toughness for the limestone under consideration
determined.
Abstract: In the article the remains of the base of the minaret,
found in 2009 at the medieval fortress shakhristan Aktobe, which is
located along the courses of the rivers Balta and Aksu. The minaret,
which consists of two parts: the stylobate in the pit and base part
refers to the XI-XII centuries. The preserved height of the building is
3.6 meters. Volume stylobat quadrangular minaret, the corners of
which are aimed at the four corners of the world amounts to 8,65 x8,
5 m, height – 2.6 m. Diameter octagonal upper cap of 7.85 m and a
height of preserved – 1 m. This minaret is of particular importance
among the historical and architectural monuments of Kazakhstan, as
it is so far the only minaret belonging to Karakhanid epoch in which
Islam was the state religion.
Abstract: The purpose of this study was to present a reliable mean for human-computer interfacing based on finger gestures made in two dimensions, which could be interpreted and adequately used in controlling a remote robot's movement. The gestures were captured and interpreted using an algorithm based on trigonometric functions, in calculating the angular displacement from one point of touch to another as the user-s finger moved within a time interval; thereby allowing for pattern spotting of the captured gesture. In this paper the design and implementation of such a gesture based user interface was presented, utilizing the aforementioned algorithm. These techniques were then used to control a remote mobile robot's movement. A resistive touch screen was selected as the gesture sensor, then utilizing a programmed microcontroller to interpret them respectively.
Abstract: The SOM has several beneficial features which make
it a useful method for data mining. One of the most important
features is the ability to preserve the topology in the projection.
There are several measures that can be used to quantify the goodness
of the map in order to obtain the optimal projection, including the
average quantization error and many topological errors. Many
researches have studied how the topology preservation should be
measured. One option consists of using the topographic error which
considers the ratio of data vectors for which the first and second best
BMUs are not adjacent. In this work we present a study of the
behaviour of the topographic error in different kinds of maps. We
have found that this error devaluates the rectangular maps and we
have studied the reasons why this happens. Finally, we suggest a new
topological error to improve the deficiency of the topographic error.
Abstract: Mercury is a natural occurring element and present in
various concentrations in the environment. Due to its toxic effects, it
is desirable to research mercury sensitive materials to adsorb
mercury. This paper describes the preparation of Au nanoparticles for
mercury adsorption by using a microwave (MW)-polyol method in
the presence of three different Sodium Chloride (NaCl)
concentrations (10, 20 and 30 mM). Mixtures of spherical, triangular,
octahedral, decahedral particles and 1-D product were obtained using
this rapid method. Sizes and shapes was found strongly depend on the
concentrations of NaCl. Without NaCl concentration, spherical,
triangular plates, octahedral, decahedral nanoparticles and 1D
product were produced. At the lower NaCl concentration (10 mM),
spherical, octahedral and decahedral nanoparticles were present,
while spherical and decahedral nanoparticles were preferentially form
by using 20 mM of NaCl concentration. Spherical, triangular plates,
octahedral and decahedral nanoparticles were obtained at the highest
NaCl concentration (30 mM). The amount of mercury adsorbed using
20 ppm mercury solution is the highest (67.5 %) for NaCl
concentration of 30 mM. The high yield of polygonal particles will
increase the mercury adsorption. In addition, the adsorption of
mercury is also due to the sizes of the particles. The sizes of particles
become smaller with increasing NaCl concentrations (size ranges, 5-
16 nm) than those synthesized without addition of NaCl (size ranges
11-32 nm). It is concluded that NaCl concentrations affects the
formation of sizes and shapes of Au nanoparticles thus affects the
mercury adsorption.
Abstract: the measurement of the angular distribution for the
elastic scattering of 16O, 14N and 12C on 27Al has been done at energy
1.75 MeV/nucleon. The optical potential code SPIVAL used in this
work to analyze the experimental results. A good agreement between
the experimental and theoretical results was obtained.
Abstract: In this paper, an analytical approach for free vibration
analysis of rectangular and circular membranes is presented. The
method is based on wave approach. From wave standpoint vibration
propagate, reflect and transmit in a structure. Firstly, the propagation
and reflection matrices for rectangular and circular membranes are
derived. Then, these matrices are combined to provide a concise and
systematic approach to free vibration analysis of membranes.
Subsequently, the eigenvalue problem for free vibration of membrane
is formulated and the equation of membrane natural frequencies is
constructed. Finally, the effectiveness of the approach is shown by
comparison of the results with existing classical solution.
Abstract: The paper presents the design of a mini-UAV attitude
controller using the backstepping method. Starting from the nonlinear
dynamic equations of the mini-UAV, by using the backstepping
method, the author of this paper obtained the expressions of the
elevator, rudder and aileron deflections, which stabilize the UAV, at
each moment, to the desired values of the attitude angles. The attitude
controller controls the attitude angles, the angular rates, the angular
accelerations and other variables that describe the UAV longitudinal
and lateral motions. To design the nonlinear controller, by using the
backstepping technique, the nonlinear equations and the Lyapunov
analysis have been directly used. The designed controller has been
implemented in Matlab/Simulink environment and its effectiveness
has been tested with a campaign of numerical simulations using data
from the UAV flight tests. The obtained results are very good and
they are better than the ones found in previous works.
Abstract: Subdivision surfaces were applied to the entire
meshes in order to produce smooth surfaces refinement from coarse
mesh. Several schemes had been introduced in this area to provide a
set of rules to converge smooth surfaces. However, to compute and
render all the vertices are really inconvenient in terms of memory
consumption and runtime during the subdivision process. It will lead
to a heavy computational load especially at a higher level of
subdivision. Adaptive subdivision is a method that subdivides only at
certain areas of the meshes while the rest were maintained less
polygons. Although adaptive subdivision occurs at the selected areas,
the quality of produced surfaces which is their smoothness can be
preserved similar as well as regular subdivision. Nevertheless,
adaptive subdivision process burdened from two causes; calculations
need to be done to define areas that are required to be subdivided and
to remove cracks created from the subdivision depth difference
between the selected and unselected areas. Unfortunately, the result
of adaptive subdivision when it reaches to the higher level of
subdivision, it still brings the problem with memory consumption.
This research brings to iterative process of adaptive subdivision to
improve the previous adaptive method that will reduce memory
consumption applied on triangular mesh. The result of this iterative
process was acceptable better in memory and appearance in order to
produce fewer polygons while it preserves smooth surfaces.
Abstract: This paper presents the utilizing of ferroelectric
material on antenna application. There are two different ferroelectric
had been used on the proposed antennas which include of Barium
Strontium Titanate (BST) and Bismuth Titanate (BiT), suitable for
Access Points operating in the WLAN IEEE 802.11 b/g and WiMAX
IEEE 802.16 within the range of 2.3 GHz to 2.5 GHz application.
BST, which had been tested to own a dielectric constant of εr = 15
while BiT has a dielectric constant that higher than BST which is εr =
21 and both materials are in rectangular shaped. The influence of
various parameters on antenna characteristics were investigated
extensively using commercial electromagnetic simulations software
by Communication Simulation Technology (CST). From theoretical
analysis and simulation results, it was demonstrated that ferroelectric
material used have not only improved the directive emission but also
enhanced the radiation efficiency.
Abstract: Global competitiveness has recently become the
biggest concern of both manufacturing and service companies.
Electronic commerce, as a key technology enables the firms to reach
all the potential consumers from all over the world. In this study, we
have presented commonly used electronic payment systems, and then
we have shown the evaluation of these systems in respect to different
criteria. The payment systems which are included in this research are
the credit card, the virtual credit card, the electronic money, the
mobile payment, the credit transfer and the debit instruments. We
have realized a systematic comparison of these systems in respect to
three main criteria: Technical, economical and social. We have
conducted a fuzzy multi-criteria decision making procedure to deal
with the multi-attribute nature of the problem. The subjectiveness
and imprecision of the evaluation process are modeled using
triangular fuzzy numbers.
Abstract: The aim of this work is to study the elastic transfer
phenomenon which takes place in the elastic scattering of 16O on 12C
at energies near the Coulomb barrier. Where, the angular distribution
decrease steadily with increasing the scattering angle, then the cross
section will increase at backward angles due to the α-transfer process.
This reaction was also studied at different energies for tracking the
nuclear rainbow phenomenon. The experimental data of the angular
distribution at these energies were compared to the calculation
predictions. The optical potential codes such as SPIVAL and
Distorted Wave Born Approximation (DWUCK5) were used in
analysis.
Abstract: In this paper an efficient incomplete factorization preconditioner is proposed for the Least Mean Squares (LMS) adaptive filter. The proposed preconditioner is approximated from a priori knowledge of the factors of input correlation matrix with an incomplete strategy, motivated by the sparsity patter of the upper triangular factor in the QRD-RLS algorithm. The convergence properties of IPLMS algorithm are comparable with those of transform domain LMS(TDLMS) algorithm. Simulation results show efficiency and robustness of the proposed algorithm with reduced computational complexity.
Abstract: Let T,U and V be rings with identity and M be a unitary (T,U)-bimodule, N be a unitary (U, V )- bimodule, D be a unitary (T, V )-bimodule . We characterize homomorphisms and isomorphisms of the generalized matrix ring Γ = T M D 0 U N 0 0 V .
Abstract: This paper deals with the extraction of information from the experts to automatically identify and recognize Ganoderma infection in oil palm stem using tomography images. Expert-s knowledge are used as rules in a Fuzzy Inference Systems to classify each individual patterns observed in he tomography image. The classification is done by defining membership functions which assigned a set of three possible hypotheses : Ganoderma infection (G), non Ganoderma infection (N) or intact stem tissue (I) to every abnormalities pattern found in the tomography image. A complete comparison between Mamdani and Sugeno style,triangular, trapezoids and mixed triangular-trapezoids membership functions and different methods of aggregation and defuzzification is also presented and analyzed to select suitable Fuzzy Inference System methods to perform the above mentioned task. The results showed that seven out of 30 initial possible combination of available Fuzzy Inference methods in MATLAB Fuzzy Toolbox were observed giving result close to the experts estimation.
Abstract: This work describes the aerodynamic characteristic for
aircraft wing model with and without bird feather like winglet. The
aerofoil used to construct the whole structure is NACA 653-218
Rectangular wing and this aerofoil has been used to compare the
result with previous research using winglet. The model of the
rectangular wing with bird feather like winglet has been fabricated
using polystyrene before design using CATIA P3 V5R13 software
and finally fabricated in wood. The experimental analysis for the
aerodynamic characteristic for rectangular wing without winglet,
wing with horizontal winglet and wing with 60 degree inclination
winglet for Reynolds number 1.66×105, 2.08×105 and 2.50×105 have
been carried out in open loop low speed wind tunnel at the
Aerodynamics laboratory in Universiti Putra Malaysia. The
experimental result shows 25-30 % reduction in drag coefficient and
10-20 % increase in lift coefficient by using bird feather like winglet
for angle of attack of 8 degree.
Abstract: This study comprehensively simulate the use of k-ε
model for predicting flow and heat transfer with measured flow field
data in a stationary duct with elucidates on the detailed physics
encountered in the fully developed flow region, and the sharp 180°
bend region. Among the major flow features predicted with accuracy
are flow transition at the entrance of the duct, the distribution of
mean and turbulent quantities in the developing, fully developed, and
sharp 180° bend, the development of secondary flows in the duct
cross-section and the sharp 180° bend, and heat transfer
augmentation. Turbulence intensities in the sharp 180° bend are
found to reach high values and local heat transfer comparisons show
that the heat transfer augmentation shifts towards the wall and along
the duct. Therefore, understanding of the unsteady heat transfer in
sharp 180° bends is important. The design and simulation are related
to concept of fluid mechanics, heat transfer and thermodynamics.
Simulation study has been conducted on the response of turbulent
flow in a rectangular duct in order to evaluate the heat transfer rate
along the small scale multiple rectangular duct
Abstract: In order to improve the simulation effects of space cold
black environment, this paper described a rectangular channel plate
heat sink. By using fluid mechanics theory and finite element method,
the internal fluid flow and heat transfer in heat sink was numerically
simulated to analyze the impact of channel structural on fluid flow and
heat transfer. The result showed that heat sink temperature uniformity
is well, and the impact of channel structural on the heat sink
temperature uniformity is not significant. The channel depth and
spacing are important factors which affect the fluid flow and heat
transfer in the heat sink. The two factors of heat transfer and resistance
need to be considered comprehensively to determine the optimal flow
structure parameters.
Abstract: This paper present a circular patch microstrip array antenna operate in KU-band (10.9GHz – 17.25GHz). The proposed circular patch array antenna will be in light weight, flexible, slim and compact unit compare with current antenna used in KU-band. The paper also presents the detail steps of designing the circular patch microstrip array antenna. An Advance Design System (ADS) software is used to compute the gain, power, radiation pattern, and S11 of the antenna. The proposed Circular patch microstrip array antenna basically is a phased array consisting of 'n' elements (circular patch antennas) arranged in a rectangular grid. The size of each element is determined by the operating frequency. The incident wave from satellite arrives at the plane of the antenna with equal phase across the surface of the array. Each 'n' element receives a small amount of power in phase with the others. There are feed network connects each element to the microstrip lines with an equal length, thus the signals reaching the circular patches are all combined in phase and the voltages add up. The significant difference of the circular patch array antenna is not come in the phase across the surface but in the magnitude distribution.