Abstract: A novel hybrid model of the lumbar spine, allowing
fast static and dynamic simulations of the disc pressure
and the spine mobility, is introduced in this work. Our
contribution is to combine rigid bodies, deformable finite
elements, articular constraints, and springs into a unique model
of the spine. Each vertebra is represented by a rigid body
controlling a surface mesh to model contacts on the facet
joints and the spinous process. The discs are modeled using
a heterogeneous tetrahedral finite element model. The facet
joints are represented as elastic joints with six degrees of
freedom, while the ligaments are modeled using non-linear
one-dimensional elastic elements. The challenge we tackle
is to make these different models efficiently interact while
respecting the principles of Anatomy and Mechanics.
The mobility, the intradiscal pressure, the facet joint force and
the instantaneous center of rotation of the lumbar spine are
validated against the experimental and theoretical results of
the literature on flexion, extension, lateral bending as well as
axial rotation.
Our hybrid model greatly simplifies the modeling task and
dramatically accelerates the simulation of pressure within the
discs, as well as the evaluation of the range of motion and the
instantaneous centers of rotation, without penalizing precision.
These results suggest that for some types of biomechanical
simulations, simplified models allow far easier modeling and
faster simulations compared to usual full-FEM approaches
without any loss of accuracy.
Abstract: The present work aims to throw light on the effects of
arcing in air on the surface state of contact pastilles made of silvernickel
Ag-Ni (60/40). Also, the photoelectric emission from these
electrical contacts has been investigated in the spectral range of 196-
256 nm. In order to study the effects of arcing on the EWF, the
metallic samples were subjected to electrical arcs in air, at
atmospheric pressure and room temperature, after that, they have
been introduced into the vacuum chamber of an experimental UHV
set-up for EWF measurements. Both Fowler method of isothermal
curves and linearized Fowler plots were used for the measurement of
the EWF by the photoelectric effect.
It has been found that the EWF varies with the number of applied
arcs. Thus, after 500 arcs in air, the observed EWF increasing is
probably due to progressive inclusion of oxide on alloy surface.
Microscopic examination is necessary to get better understandings on
EWF of silver alloys, for both virgin and arced electrical contacts.
Abstract: Multipotent mesenchymal stromal cells (MSCs)
possess immunomodulatory properties. The effect of MSCs on the
crucial cellular immunity compartment – T-cells is of a special
interest. It is known that MSC tissue niche and expected milieu of
their interaction with T- cells are characterized by low oxygen
concentration, whereas the in vitro experiments usually are carried
out at a much higher ambient oxygen (20%). We firstly evaluated
immunomodulatory effects of MSCs on T-cells at tissue-related
oxygen (5%) after interaction implied cell-to-cell contacts and
paracrine factors only. It turned out that MSCs under reduced oxygen
can effectively suppress the activation and proliferation of PHAstimulated
T-cells and can provoke decrease in the production of
proinflammatory and increase in anti-inflammatory cytokines. In
hypoxia some effects were amplified (inhibition of proliferation, antiinflammatory
cytokine profile shift). This impact was more evident
after direct cell-to-cell interaction; lack of intercellular contacts could
revoke the potentiating effect of hypoxia.
Abstract: We present a deterministic model which describes
the dynamics of tuberculosis in Algerian population where the
vaccination program with BCG is in place since 1969 and where
the WHO recommendations regarding the DOTS (directly-observed
treatment, short course) strategy are in application. The impact
of an intervention program, targeting recently infected people
among all close contacts of active cases and their treatment to
prevent endogenous reactivation, on the incidence of tuberculosis,
is investigated. We showed that a widespread treatment of latently
infected individuals for some years is recommended to shift from
higher to lower equilibrium state and thereafter relaxation is
recommended.
Abstract: The influence of transverse surface roughness on EHL characteristics has been investigated numerically using an extensive set of full EHL line contact simulations for shear-thinning lubricants under pure sliding condition. The shear-thinning behavior of lubricant is modeled using Carreau viscosity equation along with Doolittle-Tait equation for lubricant compressibility. The surface roughness is assumed to be sinusoidal and it is present on the stationary surface. It is found that surface roughness causes sharp pressure peaks along with reduction in central and minimum film thickness. With increasing amplitude of surface roughness, the minimum film thickness decreases much more rapidly as compared to the central film thickness.
Abstract: The primary objective of this paper is to study the thermal effects of the electric arc on the breaker apparatus contacts for forecasting and improving the contact durability. We will propose a model which takes account of the main influence factors on the erosion contacts. This phenomenon is very complicated because the amount of ejected metal is not necessarily constituted by the whole melted metal bath but this depends on the balance of forces on the contact surface. Consequently, to calculate the metal ejection coefficient, we propose a method which consists in comparing the experimental results with the calculated ones. The proposed model estimates the mass lost by vaporization, by droplets ejection and by the extraction mechanism of liquid or solid metal. In the one-dimensional geometry, to calculate of the contact heating, we used Green’s function which expresses the point source and allows the transition to the surface source. However, for the two- dimensional model we used explicit and implicit numerical methods. The results are similar to those found by Wilson’s experiments.
Abstract: Hepatitis C virus infection is a public health threat in Egypt. To control infection, efforts should be spent to encourage healthy behavior. This study aimed to assess the level of behavioral development in order to create a positive environment for the adoption of the recommended behaviors. The study was conducted over one year from Jan. 2011 till Jan. 2012.Knowledge, attitude and behavior of 540 HCV patients and 102 of their contacts were assessed and the level of behavioral development was determined. The study revealed that the majority of patients and contacts knew that HCV infection is dangerous with perceived concern for early diagnosis and treatment. More than 75% knew the correct modes of transmission. The assessment showed positive attitudes towards the recommended practices with intention to adopt those practices. Strategies of creating opportunities to continue the recommended behaviors should be adopted together with the reinforcement of social support.
Abstract: The authors of this paper compared ratings for leadership competences of managers in the healthcare sector and professional managers in Slovenia. Managers’ competence scores were analyzed for Slovenia and compared with some other EU countries. Comparisons of correlations yielded significant differences in leader/non-leader healthcare professionals in their relational competences. Cross-cultural comparisons also point to these differences in many countries included in the survey. Comparing these managers with the professional managers, one of the relational competences significantly distinguishes the two groups, namely the competence of taking initiative in establishing contacts with experts outside the organization. What is surprising from our analysis is the high number of competences that significantly differentiate leaders in healthcare from professional managers. Empirically based assessment provided a robust method for assessing and comparing leadership competences and point out significant results for leadership development.
Abstract: In accordance with environmental impacts contended in Kyoto Protocol, the study aims to explore the different administrative and non-administrative measurements that industrial countries, such as America, German, Japan, Korea, Holland and British take to face with the increasing Global Warming phenomena. By large, these measurements consist of versatile dimensions, including of education and advocating, economical instruments, research developments and instances, restricted instruments, voluntary contacts, exchangeable permit for carbon-release and public investments. The results of discussion for the study are as follows: both economical impacts as well as reformations for nations that are affected via Kyoto Protocol, and human testifying for variables of global surroundings in the age of Kyoto Protocol.
Abstract: The unique structural configuration found in human foot allows easy walking. Similar movement is hard to imitate even for an ape. It is obvious that human ambulation relates to the foot structure itself. Suppose the bones are represented as vertices and the joints as edges. This leads to the development of a special graph that represents human foot. On a footprint there are point-ofcontacts which have contact with the ground. It involves specific vertices. Theoretically, for an ideal ambulation, these points provide reactions onto the ground or the static equilibrium forces. They are arranged in sequence in form of a path. The ambulating footprint follows this path. Having the human foot graph and the path crossbred, it results in a representation that describes the profile of an ideal ambulation. This profile cites the locations where the point-of-contact experience normal reaction forces. It highlights the significant of these points.
Abstract: A numerical analysis of a reinforced concrete (RC) wall under missile impact loading is presented in this study. The model created by Technical Research Center of Finland was used. The commercial finite element code, LS-DYNA was used to analyze. The structural components of the reinforced concrete wall, missile and their contacts are fully modeled. The material nonlinearity with strain rate effects considering damage and failure is included in the analysis. The results of analysis were verified with other research results. The case-studies with different reinforcement ratios were conducted to investigate the influence of reinforcement on the punching behavior of walls under missile impact.
Abstract: The experimental thermal performance of two heat
exchangers in closed-wet cooling tower (CWCT) was investigated in
this study. The test sections are heat exchangers which have multi path
that is used as the entrance of cooling water and are consisting of
bare-type copper tubes between 15.88mm and 19.05mm. The process
fluids are the cooling water that flows from top part of heat exchanger
to bottom side in the inner side of tube, and spray water that flows
gravitational direction in the outer side of it. Air contacts its outer side
of that as it counterflows. Heat and mass transfer coefficients and
cooling capacity were calculated with variations of process fluids,
multi path and different diameter tubes to figure out the performance
of characteristics of CWCT.
The main results were summarized as follows: The results show this
experiment is reliable with values of heat and mass transfer
coefficients comparing to values of correlations. Heat and mass
transfer coefficients and cooling capacity of two paths are higher than
these with one path using 15.88 and 19.05mm tubes. Cooling capacity
per unit volume with 15.88mm tube using one and two paths are
higher than 19.05mm tube due to increase of surface area per unit
volume.
Abstract: Although a picture can be automatically a graphic
work, but especially in the field of graphics and images based on the
idea of advertising and graphic design will be prepared and
photographers to realize the design using his own knowledge and
skills to help does. It is evident that knowledge of photography,
photographer and designer of the facilities, fields of reaching a
higher level of quality offers. At the same time do not have a graphic
designer is also skilled photographer, but can execute your idea may
delegate to an expert photographer. Using technology and methods in
all fields of photography, graphic art may be applicable. But most of
its application in Iran, in works such as packaging, posters, Bill
Board, advertising, brochures and catalogs are. In this study, we
review how the images and techniques in the chart should be used in
Iranian graphic photo what impact has left. Using photography
techniques and procedures can be designed and helped advance the
goals graphic. Technique could not determine the idea. But what is
important to think about design and photography and his creativity
can flourish as a tool to be effective graphic designer in mind.
Computer software to help it's very promotes creativity techniques
shall graphic designer but also it is as a tool. Using images in various
fields, especially graphic arts and only because it is not being
documented, but applications are beautiful. As to his photographic
style from today is graphics. Graphic works try to affect impacts on
their audience. Hence the photo as an important factor is attention.
The other hand saw the man with the extent of forgiving and
understanding people's image, instead of using the word to your files,
allows large messages and concepts should be sent in the shortest
time. Posters, advertisements, brochures, catalog and packaging
products very diverse agricultural, industrial and food could not be
self-image. Today, the use of graphic images for a big score and the
photos to richen the role graphic design plays a major.
Abstract: There are a number of different cars for transferring hundreds of close contacts of swine influenza patients to hospital, and we need to carefully assign the passengers to those cars in order to minimize the risk of influenza spreading during transportation. The paper presents an approach to straightforward obtain the optimal solution of the relaxed problems, and develops two iterative improvement algorithms to effectively tackle the general problem.
Abstract: A computational platform is presented in this
contribution. It has been designed as a virtual laboratory to be used
for exploring optimization algorithms in biological problems. This
platform is built on a blackboard-based agent architecture. As a test
case, the version of the platform presented here is devoted to the
study of protein folding, initially with a bead-like description of the
chain and with the widely used model of hydrophobic and polar
residues (HP model). Some details of the platform design are
presented along with its capabilities and also are revised some
explorations of the protein folding problems with different types of
discrete space. It is also shown the capability of the platform to
incorporate specific tools for the structural analysis of the runs in
order to understand and improve the optimization process.
Accordingly, the results obtained demonstrate that the ensemble of
computational tools into a single platform is worthwhile by itself,
since experiments developed on it can be designed to fulfill different
levels of information in a self-consistent fashion. By now, it is being
explored how an experiment design can be useful to create a
computational agent to be included within the platform. These
inclusions of designed agents –or software pieces– are useful for the
better accomplishment of the tasks to be developed by the platform.
Clearly, while the number of agents increases the new version of the
virtual laboratory thus enhances in robustness and functionality.
Abstract: The electrical substation components are often subject to degradation due to over-voltage or over-current, caused by a short circuit or a lightning. A particular interest is given to the circuit breaker, regarding the importance of its function and its dangerous failure. This component degrades gradually due to the use, and it is also subject to the shock process resulted from the stress of isolating the fault when a short circuit occurs in the system. In this paper, based on failure mechanisms developments, the wear out of the circuit breaker contacts is modeled. The aim of this work is to evaluate its reliability and consequently its residual lifetime. The shock process is based on two random variables such as: the arrival of shocks and their magnitudes. The arrival of shocks was modeled using homogeneous Poisson process (HPP). By simulation, the dates of short-circuit arrivals were generated accompanied with their magnitudes. The same principle of simulation is applied to the amount of cumulative wear out contacts. The objective reached is to find the formulation of the wear function depending on the number of solicitations of the circuit breaker.
Abstract: An alternative iterative computational procedure is
proposed for internal normal ball loads calculation in statically
loaded single-row, angular-contact ball bearings, subjected to a
known thrust load, which is applied in the inner ring at the geometric
bearing center line. An accurate method for curvature radii at
contacts with inner and outer raceways in the direction of the motion
is used. Numerical aspects of the iterative procedure are discussed.
Numerical examples results for a 218 angular-contact ball bearing
have been compared with those from the literature. Twenty figures
are presented showing the geometrical features, the behavior of the
convergence variables and the following parameters as functions of
the thrust load: normal ball loads, contact angle, distance between
curvature centers, and normal ball and axial deflections.
Abstract: Religion revival including Islam in Kazakhstan represents reaction, first of all on internal social and political change, events after disintegration of the USSR. Process of revival of Kazakhstan Islam was accompanied as positive, so by negative tendencies. Old mosques were restored, were under construction new, Islamic schools and high schools were created, was widely studied religious the dogmatic person, the corresponding literature was published, expanded contacts with foreign Muslim brothers in the faith, the centers of the Arab-Muslim culture extended. At the same time in Kazakhstan, there are religious-political parties and movements, pursuing radical goals down to change the spiritual and cultural identity of Muslims of Kazakhstan by the forcible introduction of non-traditional religious and political, ethnic and cultural values.
Abstract: The purpose of this research is: a) to investigate how
the HR practices influence psychological contracts, b) to examine the
influence of psychological contracts to individual behavior and to
contribute individually, c) to study the psychological contact through
leadership. This research using mixed methods, qualitative and
quantitative research methods were utilized to gather the data
collected using a qualitative method by the HR Manager who is in
charge of the trainings from the staffs and quantitative method
(survey) by using questionnaire was utilized to draw upon and to
elaborate on the recurring themes present during the interviews. The
survey was done to 400 staffs of the company. The study found that
leadership styles supporting the firm’s HR strategy is the key in
making psychological contracts that benefit both the firm and its
members.
Abstract: The electrical and structural properties of Hf/Al/Ni/Au
(20/100/25/50 nm) ohmic contact to n-GaN are reported in this study.
Specific contact resistivities of Hf/Al/Ni/Au based contacts have been
investigated as a function of annealing temperature and achieve the
lowest value of 1.09´10-6 Ω·cm2 after annealing at 650 oC in vacuum.
A detailed mechanism of ohmic contact formation is discussed. By
using different chemical analyses, it is anticipated that the formation of
Hf-Al-N alloy might be responsible to form low temperature ohmic
contacts for the Hf-based scheme to n-GaN.