Abstract: Carbon nanotubes (CNTs) are known for having high elastic properties with high surface area that promote them as good candidates for reinforcing polymeric matrices. In composite materials, CNTs lack chemical bonding with the surrounding matrix which decreases the possibility of better stress transfer between the components. In this work, a chemical treatment for activating the surface of the multi-wall carbon nanotubes (MWCNT) was applied and the effect of this functionalization on the elastic properties of the epoxy nanocomposites was studied. Functional amino-groups were added to the surface of the CNTs and it was evaluated to be about 34% of the total weight of the CNTs. Elastic modulus was found to increase by about 40% of the neat epoxy resin at CNTs’ weight fraction of 0.5%. The elastic modulus was found to decrease after reaching a certain concentration of CNTs which was found to be 1% wt. The scanning electron microscopic pictures showed the effect of the CNTs on the crack propagation through the sample by forming stress concentrated spots at the nanocomposite samples.
Abstract: The work reported through this paper is an
experimental work conducted on High Performance Concrete (HPC)
with super plasticizer with the aim to develop some models suitable
for prediction of compressive strength of HPC mixes. In this study,
the effect of varying proportions of fly ash (0% to 50% @ 10%
increment) on compressive strength of high performance concrete has
been evaluated. The mix designs studied were M30, M40 and M50 to
compare the effect of fly ash addition on the properties of these
concrete mixes. In all eighteen concrete mixes that have been
designed, three were conventional concretes for three grades under
discussion and fifteen were HPC with fly ash with varying
percentages of fly ash. The concrete mix designing has been done in
accordance with Indian standard recommended guidelines. All the
concrete mixes have been studied in terms of compressive strength at
7 days, 28 days, 90 days, and 365 days. All the materials used have
been kept same throughout the study to get a perfect comparison of
values of results. The models for compressive strength prediction
have been developed using Linear Regression method (LR), Artificial
Neural Network (ANN) and Leave-One-Out Validation (LOOV)
methods.
Abstract: This paper describes a sliding mode controller for
autonomous underwater vehicles (AUVs). The dynamic of AUV
model is highly nonlinear because of many factors, such as
hydrodynamic drag, damping, and lift forces, Coriolis and centripetal
forces, gravity and buoyancy forces, as well as forces from thruster.
To address these difficulties, a nonlinear sliding mode controller is
designed to approximate the nonlinear dynamics of AUV and
improve trajectory tracking. Moreover, the proposed controller can
profoundly attenuate the effects of uncertainties and external
disturbances in the closed-loop system. Using the Lyapunov theory
the boundedness of AUV tracking errors and the stability of the
proposed control system are also guaranteed. Numerical simulation
studies of an AUV are included to illustrate the effectiveness of the
presented approach.
Abstract: Radiative heat transfer in participating medium was
carried out using the finite volume method. The radiative transfer
equations are formulated for absorbing and anisotropically scattering
and emitting medium. The solution strategy is discussed and the
conditions for computational stability are conferred. The equations
have been solved for transient radiative medium and transient
radiation incorporated with transient conduction. Results have been
obtained for irradiation and corresponding heat fluxes for both the
cases. The solutions can be used to conclude incident energy and
surface heat flux. Transient solutions were obtained for a slab of heat
conducting in slab and by thermal radiation. The effect of heat
conduction during the transient phase is to partially equalize the
internal temperature distribution. The solution procedure provides
accurate temperature distributions in these regions. A finite volume
procedure with variable space and time increments is used to solve
the transient radiation equation. The medium in the enclosure
absorbs, emits, and anisotropically scatters radiative energy. The
incident radiations and the radiative heat fluxes are presented in
graphical forms. The phase function anisotropy plays a significant
role in the radiation heat transfer when the boundary condition is
non-symmetric.
Abstract: Target of this study was the analysis of the impact of
crude glycerol on canine spermatozoa motility, morphology,
viability, and membrane integrity. Experiments were realized in vitro.
In the study, semen from 5 large dog breeds was used. They were
typical representatives of large breeds, coming from healthy rearing,
regularly vaccinated and integrated to the further breeding. Semen
collections were realized at the owners of animals and in the
veterinary clinic. Subsequently the experiments were realized at the
Department of Animal Physiology of the SUA in Nitra. The
spermatozoa motility was evaluated using CASA analyzer
(SpermVisionTM, Minitub, Germany) at the temperature 5 and 37°C
for 5 hours. In the study, 13 motility parameters were evaluated.
Generally, crude glycerol has generally negative effect on
spermatozoa motility. Morphological analysis was realized using
Hancock staining and the preparations were evaluated at
magnification 1000x using classification tables of morphologically
changed spermatozoa. Data clearly detected the highest number of
morphologically changed spermatozoa in the experimental groups
(know twisted tails, tail torso and tail coiling). For acrosome
alterations swelled acrosomes, removed acrosomes and acrosomes
with undulated membrane were detected. In this study also the effect
of crude glycerol on spermatozoa membrane integrity were analyzed.
The highest crude glycerol concentration significantly affects
spermatozoa integrity. Results of this study show that crude glycerol
has effect of spermatozoa motility, viability, and membrane integrity.
Detected changes are related to crude glycerol concentration,
temperature, as well as time of incubation.
Abstract: Lots of motors have been being used in industry.
Therefore many researchers have studied about the failure diagnosis of
motors. In this paper, the effect of measuring environment for
diagnosis of gear fault connected to a motor shaft is studied. The fault
diagnosis is executed through the comparison of normal gear and
abnormal gear. The measured FFT data are compared with the normal
data and analyzed for q-axis current, noise and vibration. For bad and
good environment, the diagnosis results are compared. From these, it
is shown that the bad measuring environment may not be able to detect
exactly the motor gear fault. Therefore it is emphasized that the
measuring environment should be carefully prepared.
Abstract: Health workforce is a fundamental component of
health system and plays a significant role in delivering effective
health care services. However, there is a crucial shortage of skilled
personnel which make them prone to work in stressful conditions. In
spite of excessively high workload and burnout among the staff, little
attention is given to their job satisfaction level which has serious
implications on the productivity and effective performance of staff to
achieve organizational goals. Therefore, this study aims to explore
the job satisfaction of midwives working in the labor ward of the
Lady Dufferin Hospital, Karachi. A cross-sectional survey was
conducted. The short version of Minnesota Job Satisfaction
Questionnaire was administered on a convenient sample group of 22
midwives to gather information on their job satisfaction. The results
demonstrated that midwives were overall satisfied with their job. The
level of job satisfaction was however found different in various
positions within midwifery cadre. The head of midwives was highly
satisfied as compared to midwifery staff who works under the
supervision of head. The level of satisfaction of team leaders fall
between the head and staff of midwifery. Similar trends were
observed for both intrinsic and extrinsic job satisfaction. Such
evidences on these issues are essential and useful as it helps explore
the attitudes of individuals towards work which has direct
implications on access to quality care services. Strategic interventions
are required at organizational level to provide motivators and
satisfiers to health workers for their work related satisfaction and
enhanced motivation.
Abstract: The shielding ability of a shielding cavity with an
aperture will be greatly degraded at resonance frequencies, and the
resonance modes and frequencies are affected by aperture resonances
and aperture-cavity coupling, which are closely related with aperture
sizes. The equivalent circuit method and numerical method of
Transmission Line Matrix (TLM) are used to analyze the effects of
aperture resonances and aperture-cavity coupling on the
electromagnetic resonances of a cavity with an aperture in this paper.
Both analytical and numerical results show that the resonance modes
of a shielding cavity with an aperture consist of cavity resonance
modes and aperture resonance modes, and the resonance frequencies
will shift with the change of the aperture sizes because of the aperture
resonances and aperture-cavity coupling. Variation rules of
electromagnetic resonances with aperture sizes for a cavity with an
aperture are given, which will be useful for design of shielding
cavities.
Abstract: In this work, we attempt to associate firm
characteristics with innovative activity. We collect microdata from
listed firms of selected Eurozone Country-members, after the
beginning of 2007 financial crisis. The following literature, several
indicators of growth and performance were selected and tested for
their ability to interpret innovative activity. The main scope is to
examine the possible differences in performance and growth between
innovative and non-innovative firms, during a severe recession.
Additionally to that, a special focus will be held on whether
macroeconomic performance and national innovation system,
determines the extent of innovators' performance. Preliminary
findings, through correlation matrices and non-parametric tests,
strongly indicate the positive relation between innovative activity and
most of the measures used (profitability, size, employment),
confirming that even during a recessionary period, innovative firms
not only survive but also seem to succeed better economic results in
almost all indexes relative to non-innovative. However, even though
innovators seem to perform better in all economies examined, the
extent of that performance seems to be strongly affected by the
supportive mechanisms (financial and structural) that their country
provides. Thus, it is clear, that the technologically intensive 'gap'
between European South and North, during the economic crisis,
became chaotic, due to the harsh austerity measures and reduced
budgets in those countries, even in sectors with high potentials in
economic activity and employment, impairing the effects of crisis and
enhancing the vicious circle of recession.
Abstract: Thermal enhancement of a single mini channel in
Proton Exchange Membrane Fuel Cell (PEMFC) cooling plate is
numerically investigated. In this study, low concentration of Al2O3 in
Water - Ethylene Glycol mixtures is used as coolant in single channel
of carbon graphite plate to mimic the mini channels in PEMFC
cooling plate. A steady and incompressible flow with constant heat
flux is assumed in the channel of 1mm x 5mm x 100mm. Nano
particle of Al2O3 used ranges from 0.1, 0.3 and 0.5 vol %
concentration and then dispersed in 60:40 (water: Ethylene Glycol)
mixture. The effect of different flow rates to fluid flow and heat
transfer enhancement in Re number range of 20 to 140 was observed.
The result showed that heat transfer coefficient was improved by
18.11%, 9.86% and 5.37% for 0.5, 0.3 and 0.1 vol. % Al2O3 in 60:40
(water: EG) as compared to base fluid of 60:40 (water: EG). It is also
showed that the higher vol. % concentration of Al2O3 performed
better in term of thermal enhancement but at the expense of higher
pumping power required due to increase in pressure drop
experienced. Maximum additional pumping power of 0.0012W was
required for 0.5 vol % Al2O3 in 60:40 (water: EG) at Re number 140.
Abstract: In this numerical work, mixed convection and entropy
generation of Cu–water nanofluid in a lid-driven square cavity have
been investigated numerically using the Lattice Boltzmann Method.
Horizontal walls of the cavity are adiabatic and vertical walls have
constant temperature but different values. The top wall has been
considered as moving from left to right at a constant speed, U0. The
effects of different parameters such as nanoparticle volume
concentration (0–0.05), Rayleigh number (104–106) and Reynolds
numbers (1, 10 and 100) on the entropy generation, flow and
temperature fields are studied. The results have shown that addition
of nanoparticles to the base fluid affects the entropy generation, flow
pattern and thermal behavior especially at higher Rayleigh and low
Reynolds numbers. For pure fluid as well as nanofluid, the increase
of Reynolds number increases the average Nusselt number and the
total entropy generation, linearly. The maximum entropy generation
occurs in nanofluid at low Rayleigh number and at high Reynolds
number. The minimum entropy generation occurs in pure fluid at low
Rayleigh and Reynolds numbers. Also at higher Reynolds number,
the effect of Cu nanoparticles on enhancement of heat transfer was
decreased because the effect of lid-driven cavity was increased. The
present results are validated by favorable comparisons with
previously published results. The results of the problem are presented
in graphical and tabular forms and discussed.
Abstract: Operation enhancement in an air cooler depends on
rate of heat transfer, and pressure drop. In this paper for a given heat
duty, study of the effects of FPI (Fin Per Inch) and fin type (circular
and hexagonal fins) on heat transfer, and pressure drop in an air
cooler in Iran, Arvand petrochemical. A program in EES
(Engineering Equations Solver) software moreover, Aspen B-JAC
and HTFS+ softwares are used for this purpose to solve governing
equations. At first the simulated results obtained from this program is
compared to the experimental data for two cases of FPI. The effects
of FPI from 3 to 15 over heat transfer (Q) to pressure drop ratio
(Q/Δp ratio). This ratio is one of the main parameters in design, and
simulation heat exchangers. The results show that heat transfer (Q)
and pressure drop increase with increasing FPI steadily, and the Q/Δp
ratio increases to FPI=12 and then decreased gradually to FPI=15,
and Q/Δp ratio is maximum at FPI=12. The FPI value selection
between 8 and 12 obtained as a result to optimum heat transfer to
pressure drop ratio. Also by contrast, between circular and hexagonal
fins results, the Q/Δp ratio of hexagonal fins more than Q/Δp ratio of
circular fins for FPI between 8 and 12 (optimum FPI)
Abstract: This paper proposes a novel heuristic algorithm that aims to determine the best size and location of distributed generators in unbalanced distribution networks. The proposed heuristic algorithm can deal with the planning cases where power loss is to be optimized without violating the system practical constraints. The distributed generation units in the proposed algorithm is modeled as voltage controlled node with the flexibility to be converted to constant power factor node in case of reactive power limit violation. The proposed algorithm is implemented in MATLAB and tested on the IEEE 37 -node feeder. The results obtained show the effectiveness of the proposed algorithm.
Abstract: Tannins are a unique category of plant phytochemicals
especially in terms of their vast potential health-benefiting properties.
Researchers have described the capacity of tannins to enhance
glucose uptake and inhibit adipogenesis, thus being potential drugs
for the treatment of non-insulin dependent diabetes mellitus. Thus,
the present research was conducted to find out tannin content of food
products. The percentage of tannin in various analyzed sources
ranged from 0.0 to 108.53%; highest in kathaa and lowest in ker and
mango bark. The percentage of tannins present in the plants,
however, varies. Numerous studies have confirmed that the naturally
occurring polyphenols are key factor for the beneficial effects of the
herbal medicines. Isolation and identification of active constituents
from plants, preparation of standardized dose & dosage regimen can
play a significant role in improving the hypoglycaemic action.
Abstract: The latest years the number of immigrants at Greece
has increased dramatically. Their impact on the National Health
System (NHS) has not been yet thoroughly investigated. This paper
analyses the cost of immigrants to the NHS hospitals of the region of
Eastern Macedonia and Thrace. The data are collected from 2005 to
2011 from five different hospitals and are analysed using linear
mixed effects models in order to investigate the effects of nationality
and year on the cost of hospitalization and treatment. The results
show that generally the Greek nationality patients have a higher mean
cost of hospitalization compared to the immigrants and that there is
an increasing trend for the cost except for the year 2010.
Abstract: The paper aims to evaluate the effect of online
advertising on consumer purchase behavior in Malaysian
organizations. The paper has potential to extend and refine theory. A
survey was distributed among Students of UTM university during the
winter 2014 and 160 responses were collected. Regression analysis
was used to test the hypothesized relationships of the model. Result
shows that the predictors (cost saving factor, convenience factor and
customized product or services) have positive impact on intention to
continue seeking online advertising.
Abstract: The present study analyzed the effect of discrimination
experience on the life satisfaction in women with severe disabilities
and the mediating effect of disability acceptance. In verifying this
mediating effect of disability acceptance between discrimination
experience and life satisfaction, both discrimination experience and
disability acceptance were found to be statistically significant in the
first and second phases. Disability acceptance was found to have a
mediating effect on the relationship between discrimination
experience and life satisfaction. Based on this finding, measures for
enhancing the quality of life in individuals with disabilities that
experience low levels of life satisfaction were proposed.
Abstract: This work explores the inter-region investment
behaviors of Integrated Circuit (IC) design industry from Taiwan to
China using the amount of foreign direct investment (FDI). According
to the mutual dependence among different IC design industrial
locations, Lotka-Volterra model is utilized to explore the FDI
interactions between South and East China. Effects of inter-regional
collaborations on FDI flows into China are considered. The analysis
results show that FDIs into South China for IC design industry
significantly inspire the subsequent FDIs into East China, while FDIs
into East China for Taiwan’s IC design industry significantly hinder
the subsequent FDIs into South China. Because the supply chain along
IC industry includes upstream IC design, midstream manufacturing, as
well as downstream packing and testing enterprises, IC design industry
has to cooperate with IC manufacturing, packaging and testing
industries in the same area to form a strong IC industrial cluster.
Taiwan’s IC design industry implement the largest FDI amount into
East China and the second largest FDI amount into South China
among the four regions: North, East, Mid-West and South China. If IC
design houses undertake more FDIs in South China, those in East
China are urged to incrementally implement more FDIs into East
China to maintain the competitive advantages of the IC supply chain in
East China. On the other hand, as the FDIs in East China rise, the FDIs
in South China will successively decline since capitals have
concentrated in East China. In addition, this investigation proves that
the prediction of Lotka-Volterra model in FDI trends is accurate
because the industrial interactions between the two regions are
included. Finally, this work confirms that the FDI flows cannot reach a
stable equilibrium point, so the FDI inflows into East and South China
will expand in the future.
Abstract: Rapid population growth, urbanization and
industrialization are known as the most important factors of
environment problems. Elimination and management of solid wastes
are also within the most important environment problems. One of the
main problems in solid waste management is the selection of the best
site for elimination of solid wastes. Lately, Geographical Information
System (GIS) has been used for easing selection of landfill area. GIS
has the ability of imitating necessary economic, environmental and
political limitations. They play an important role for the site selection
of landfill area as a decision support tool. In this study; map layers will be studied for minimum effect of
environmental, social and cultural factors and maximum effect for
engineering/economic factors for site selection of landfill areas and
using GIS for a decision support mechanism in solid waste landfill
areas site selection will be presented in Aksaray/Turkey city,
Güzelyurt district practice.
Abstract: The consumption of food contaminated with molds
(microscopic filamentous fungi) and their toxic metabolites results in
the development of food-borne mycotoxicosis. The spores of molds
are ubiquitously spread in the environment and can be detected
everywhere. Ochratoxin A is a toxic and potentially carcinogenic
fungal toxin found in a variety of food commodities. In this study, the
mycological quality of various ready-to-eat local and imported pork
meat and meat byproducts sold in Egyptian markets were assessed
and the presence of various molds was determined in pork used as a
raw material, edible organs as liver and kidney as well as in
fermented raw meat by-products. The study assessed the mycological
quality of pork raw meat and their by-products sold in commercial
shops in Cairo, Egypt. Mycological analysis was conducted on
(n=110) samples which included pig’s livers and kidneys from
Egyptian Bassatin slaughter house; local and imported processed
pork meat by-products from Egyptian pork markets. The isolates
were identified using traditional mycological and biochemical tests.
All kidney and liver samples were positive to molds growth while all
byproducts were negative. Ochratoxin A levels were quantitatively
analyzed using the high performance liquid chromatography (HPLC)
and the highest results were present in kidney 7.51 part per billion
(ppb) followed by minced meat 6.19 ppb generally the local samples
showed higher levels than the imported ones. To the best of our
knowledge, this is the first report on mycotoxins detection and
quantification from pork by-products in Egypt.