Abstract: Nowadays, several techniques such as; Fuzzy
Inference System (FIS) and Neural Network (NN) are employed for
developing of the predictive models to estimate parameters of water
quality. The main objective of this study is to compare between the
predictive ability of the Adaptive Neuro-Fuzzy Inference System
(ANFIS) model and Artificial Neural Network (ANN) model to
estimate the Biochemical Oxygen Demand (BOD) on data from 11
sampling sites of Saen Saep canal in Bangkok, Thailand. The data is
obtained from the Department of Drainage and Sewerage, Bangkok
Metropolitan Administration, during 2004-2011. The five parameters
of water quality namely Dissolved Oxygen (DO), Chemical Oxygen
Demand (COD), Ammonia Nitrogen (NH3N), Nitrate Nitrogen
(NO3N), and Total Coliform bacteria (T-coliform) are used as the
input of the models. These water quality indices affect the
biochemical oxygen demand. The experimental results indicate that
the ANN model provides a higher correlation coefficient (R=0.73)
and a lower root mean square error (RMSE=4.53) than the
corresponding ANFIS model.
Abstract: Dense slurry flow through centrifugal pump casing
has been modeled using the Eulerian-Eulerian approach with
Eulerian multiphase model in FLUENT 6.1®. First order upwinding
is considered for the discretization of momentum, k and ε terms.
SIMPLE algorithm has been applied for dealing with pressurevelocity
coupling. A mixture property based k-ε turbulence model
has been used for modeling turbulence. Results are validated first
against mesh independence and experiments for a particular set of
operational and geometric conditions. Parametric analysis is then
performed to determine the effect on important physical quantities
viz. solid velocities, solid concentration and solid stresses near the
wall with various operational geometric conditions of the pump.
Abstract: Using a texture database, a statistical estimation of
spring-back was conducted in this study on the basis of statistical
analysis. Both spring-back in bending deformation and experimental
data related to the crystal orientation show significant dispersion.
Therefore, a probabilistic statistical approach was established for the
proper quantification of these values. Correlation was examined
among the parameters F(x) of spring-back, F(x) of the buildup fraction
to three orientations after 92° bending, and F(x) at an as-received part
on the basis of the three-parameter Weibull distribution. Consequent
spring-back estimation using a texture database yielded excellent
estimates compared with experimental values.
Abstract: For high-speed control of robots, a good knowledge of system modelling is necessary to obtain the desired bandwidth. In this paper, we present a cartesian robot with a pan/tilt unit in end-effector (5 dof). This robot is implemented with powerful direct drive AC induction machines. The dynamic model, parameter identification and model validation of the robot are studied (including actuators). This work considers the cartesian robot coupled and non linear (contrary to normal considerations for this type of robots). The mechanical and control architecture proposed in this paper is efficient for industrial and research application in which high speed, well known model and very high accuracy are required.
Abstract: System identification is the process of creating
models of dynamic process from input- output signals. The aim of
system identification can be identified as “ to find a model with
adjustable parameters and then to adjust them so that the predicted
output matches the measured output". This paper presents a method
of modeling and simulating with system identification to achieve the
maximum fitness for transformation function. First by using
optimized KLM equivalent circuit for PVDF piezoelectric transducer
and assuming different inputs including: sinuside, step and sum of
sinusides, get the outputs, then by using system identification
toolbox in MATLAB, we estimate the transformation function from
inputs and outputs resulted in last program. Then compare the fitness
of transformation function resulted from using ARX,OE(Output-
Error) and BJ(Box-Jenkins) models in system identification toolbox
and primary transformation function form KLM equivalent circuit.
Abstract: An experimental and numerical study has been conducted to clarify heat transfer characteristics and effectiveness of a cross-flow heat exchanger employing staggered wing-shaped tubes at different angels of attack. The water-side Rew and the air-side Rea were at 5 x 102 and at from 1.8 x 103 to 9.7 x 103, respectively. The tubes arrangements were employed with various angles of attack θ1,2,3 from 0° to 330° at the considered Rea range. Correlation of Nu, St, as well as the heat transfer per unit pumping power (ε) in terms of Rea, design parameters for the studied bundle were presented. The temperature fields around the staggered wing-shaped tubes bundle were predicted by using commercial CFD FLUENT 6.3.26 software package. Results indicated that the heat transfer was increased by increasing the angle of attack from 0° to 45°, while the opposite was true for angles of attack from 135° to 180°. The best thermal performance and hence η of studied bundle was occurred at the lowest Rea and/or zero angle of attack. Comparisons between the experimental and numerical results of the present study and those, previously, obtained for similar available studies showed good agreements.
Abstract: We consider optimal channel equalization for MIMO
(multi-input/multi-output) time-varying channels in the sense of
MMSE (minimum mean-squared-error), where the observation noise
can be non-stationary. We show that all ZF (zero-forcing) receivers
can be parameterized in an affine form which eliminates completely
the ISI (inter-symbol-interference), and optimal channel equalizers
can be designed through minimization of the MSE (mean-squarederror)
between the detected signals and the transmitted signals,
among all ZF receivers. We demonstrate that the optimal channel
equalizer is a modified Kalman filter, and show that under the AWGN
(additive white Gaussian noise) assumption, the proposed optimal
channel equalizer minimizes the BER (bit error rate) among all
possible ZF receivers. Our results are applicable to optimal channel
equalization for DWMT (discrete wavelet multitone), multirate transmultiplexers,
OFDM (orthogonal frequency division multiplexing),
and DS (direct sequence) CDMA (code division multiple access)
wireless data communication systems. A design algorithm for optimal
channel equalization is developed, and several simulation examples
are worked out to illustrate the proposed design algorithm.
Abstract: Development of artificial neural network (ANN) for
prediction of aluminum workpieces' surface roughness in ultrasonicvibration
assisted turning (UAT) has been the subject of the present
study. Tool wear as the main cause of surface roughness was also
investigated. ANN was trained through experimental data obtained
on the basis of full factorial design of experiments. Various
influential machining parameters were taken into consideration. It
was illustrated that a multilayer perceptron neural network could
efficiently model the surface roughness as the response of the
network, with an error less than ten percent. The performance of the
trained network was verified by further experiments. The results of
UAT were compared with the results of conventional turning
experiments carried out with similar machining parameters except for
the vibration amplitude whence considerable reduction was observed
in the built-up edge and the surface roughness.
Abstract: This work presents a novel means of extracting fixedlength parameters from voice signals, such that words can be recognized
in linear time. The power and the zero crossing rate are first
calculated segment by segment from a voice signal; by doing so, two
feature sequences are generated. We then construct an FIR system
across these two sequences. The parameters of this FIR system, used
as the input of a multilayer proceptron recognizer, can be derived by
recursive LSE (least-square estimation), implying that the complexity of overall process is linear to the signal size. In the second part of
this work, we introduce a weighting factor λ to emphasize recent
input; therefore, we can further recognize continuous speech signals.
Experiments employ the voice signals of numbers, from zero to nine, spoken in Mandarin Chinese. The proposed method is verified to
recognize voice signals efficiently and accurately.
Abstract: The application of a Static Synchronous Series Compensator (SSSC) controller to improve the transient stability performance of a power system is thoroughly investigated in this paper. The design problem of SSSC controller is formulated as an optimization problem and Particle Swarm Optimization (PSO) Technique is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor angle of the generator is involved; transient stability performance of the system is improved. The proposed controller is tested on a weakly connected power system subjected to different severe disturbances. The non-linear simulation results are presented to show the effectiveness of the proposed controller and its ability to provide efficient damping of low frequency oscillations. It is also observed that the proposed SSSC controller improves greatly the voltage profile of the system under severe disturbances.
Abstract: This paper presents a comparative study on two most
popular control strategies for Permanent Magnet Synchronous Motor
(PMSM) drives: field-oriented control (FOC) and direct torque
control (DTC). The comparison is based on various criteria including
basic control characteristics, dynamic performance, and
implementation complexity. The study is done by simulation using
the Simulink Power System Blockset that allows a complete
representation of the power section (inverter and PMSM) and the
control system. The simulation and evaluation of both control
strategies are performed using actual parameters of Permanent
Magnet Synchronous Motor fed by an IGBT PWM inverter.
Abstract: In this paper, we have examined the effect of process
parameter variation on the electrical characteristics of an LDMOS
device. The rate of change in the electrical parameters such as cut off
frequency, breakdown voltage and drain saturation current as a
function of the process parameters is investigated
Abstract: The present work is concerned with sulfidation of Cu,
Zn and Ni containing plating wastewater with CaS. The sulfidation
experiments were carried out at a room temperature by adding solid
CaS to simulated metal solution containing either single-metal of Ni,
Zn and Cu, or Ni-Zn-Cu mixture. At first, the experiments were
conducted without pH adjustment and it was found that the complete
sulfidation of Zn and Ni was achieved at an equimolar ratio of CaS to a
particular metal. However, in the case of Cu, a complete copper
sulfidation was achieved at CaS to Cu molar ratio of about 2. In the
case of the selective sulfidation, a simulated plating solution
containing Cu, Zn and Ni at the concentration of 100 mg/dm3 was
treated with CaS under various pH conditions. As a result, selective
precipitation of metal sulfides was achieved by a sulfidation treatment
at different pH values. Further, the precipitation agents of NaOH,
Na2S and CaS were compared in terms of the average specific
filtration resistance and compressibility coefficients of metal sulfide
slurry. Consequently, based on the lowest filtration parameters of the
produced metal sulfides, it was concluded that CaS was the most
effective precipitation agent for separation and recovery of Cu, Zn and
Ni.
Abstract: The paper is concerned with developing stochastic delay mechanisms for efficient multicast protocols and for smooth mobile handover processes which are capable of preserving a given Quality of Service (QoS). In both applications the participating entities (receiver nodes or subscribers) sample a stochastic timer and generate load after a random delay. In this way, the load on the networking resources is evenly distributed which helps to maintain QoS communication. The optimal timer distributions have been sought in different p.d.f. families (e.g. exponential, power law and radial basis function) and the optimal parameter have been found in a recursive manner. Detailed simulations have demonstrated the improvement in performance both in the case of multicast and mobile handover applications.
Abstract: Access control is a critical security service in Wire- less
Sensor Networks (WSNs). To prevent malicious nodes from joining
the sensor network, access control is required. On one hand, WSN
must be able to authorize and grant users the right to access to the
network. On the other hand, WSN must organize data collected by
sensors in such a way that an unauthorized entity (the adversary)
cannot make arbitrary queries. This restricts the network access only
to eligible users and sensor nodes, while queries from outsiders will
not be answered or forwarded by nodes. In this paper we presentee
different access control schemes so as to ?nd out their objectives,
provision, communication complexity, limits, etc. Using the node
density parameter, we also provide a comparison of these proposed
access control algorithms based on the network topology which can
be flat or hierarchical.
Abstract: The main goal of the present work is to decrease the
computational burden for optimum design of steel frames with
frequency constraints using a new type of neural networks called
Wavelet Neural Network. It is contested to train a suitable neural
network for frequency approximation work as the analysis program.
The combination of wavelet theory and Neural Networks (NN)
has lead to the development of wavelet neural networks.
Wavelet neural networks are feed-forward networks using
wavelet as activation function. Wavelets are mathematical
functions within suitable inner parameters, which help them to
approximate arbitrary functions. WNN was used to predict the
frequency of the structures. In WNN a RAtional function with
Second order Poles (RASP) wavelet was used as a transfer
function. It is shown that the convergence speed was faster
than other neural networks. Also comparisons of WNN with
the embedded Artificial Neural Network (ANN) and with
approximate techniques and also with analytical solutions are
available in the literature.
Abstract: In cellular networks, limited availability of resources
has to be tapped to its fullest potential. In view of this aspect, a
sophisticated averaging and voting technique has been discussed in
this paper, wherein the radio resources available are utilized to the
fullest value by taking into consideration, several network and radio
parameters which decide on when the handover has to be made and
thereby reducing the load on Base station .The increase in the load
on the Base station might be due to several unnecessary handover
taking place which can be eliminated by making judicious use of the
radio and network parameters.
Abstract: Zero inflated strict arcsine model is a newly developed
model which is found to be appropriate in modeling overdispersed
count data. In this study, we extend zero inflated strict arcsine model
to zero inflated strict arcsine regression model by taking into
consideration the extra variability caused by extra zeros and
covariates in count data. Maximum likelihood estimation method is
used in estimating the parameters for this zero inflated strict arcsine
regression model.
Abstract: The so-called all-pass filter circuits are commonly
used in the field of signal processing, control and measurement.
Being connected to capacitive loads, these circuits tend to loose their
stability; therefore the elaborate analysis of their dynamic behavior is
necessary. The compensation methods intending to increase the
stability of such circuits are discussed in this paper, including the socalled
lead-lag compensation technique being treated in detail. For
the dynamic modeling, a two-port network model of the all-pass filter
is being derived. The results of the model analysis show, that
effective lead-lag compensation can be achieved, alone by the
optimization of the circuit parameters; therefore the application of
additional electric components are not needed to fulfill the stability
requirement.
Abstract: Paper presents simple sixport principle and its frequency bandwidth. The novel multisixport approach is presented with its possibilities, typical parameters and frequency bandwidth. Practical implementation is shown with its measurement parameters and calibration. The bandwidth circa 1:100 is obtained.