Abstract: The use of electronic sensors in the electronics
industry has become increasingly popular over the past few years,
and it has become a high competition product. The frequency
adjustment process is regarded as one of the most important process
in the electronic sensor manufacturing process. Due to inaccuracies
in the frequency adjustment process, up to 80% waste can be caused
due to rework processes; therefore, this study aims to provide a
preliminary understanding of the role of parameters used in the
frequency adjustment process, and also make suggestions in order to
further improve performance. Four parameters are considered in this
study: air pressure, dispensing time, vacuum force, and the distance
between the needle tip and the product. A full factorial design for
experiment 2k was considered to determine those parameters that
significantly affect the accuracy of the frequency adjustment process,
where a deviation in the frequency after adjustment and the target
frequency is expected to be 0 kHz. The experiment was conducted on
two levels, using two replications and with five center-points added.
In total, 37 experiments were carried out. The results reveal that air
pressure and dispensing time significantly affect the frequency
adjustment process. The mathematical relationship between these
two parameters was formulated, and the optimal parameters for air
pressure and dispensing time were found to be 0.45 MPa and 458 ms,
respectively. The optimal parameters were examined by carrying out
a confirmation experiment in which an average deviation of 0.082
kHz was achieved.
Abstract: Aroma forming volatiles are important components of
fermented beverages. The aim of current research is to evaluate the
volatile compounds and phenolic compounds of commercial ciders.
Volatile aroma compounds and TPC of seven commercial ciders
were determined. Extraction of aroma compounds was performed
using solid phase microextraction (DVB/Car/PDMS fibre). Analysis
of volatile aroma compounds was made using a Perkin Elmer Clarus
500 GC/MS. Total phenol content (TPC) was determined according
to the Folin-Ciocalteu spectrophotometric method and results were
expressed as gallic acid equivalents. The highest volatile compounds
were in apple ciders with pear flavor. The highest TPC and lower
content of volatile compounds were detected in French ciders.
Abstract: This paper examines the relationship between financial
risks and profitability of the conventional and Islamic banks in
Malaysia for the period between 1996 and 2005. The measures of
profitability that have been used in the study are the return on equity
(ROE) and return on assets (ROA) while the financial risks are credit
risk, interest rate risk and liquidity risks. This study employs panel
data regression analysis of Generalised Least Squares of fixed effects
and random effects models. It was found that credit risk has a
significant impact on ROA and ROE for the conventional as well as
the Islamic banks. The relationship between interest rate risk and ROE
were found to be weakly significant for the conventional banks and
insignificant for the Islamic banks. The effect of interest rate risk on
ROA is significant for the conventional banks. Liquidity risk was
found to have an insignificant impact on both profitability measures.
Abstract: Availability and mobilization of revenue is the main
essential with which an economy is managed and run. While
planning or while making the budgets nations set revenue targets to
be achieved. But later when the accounts are closed the actual
collections of revenue through taxes or even the non-tax revenue
collection would invariably be different as compared to the initial
estimates and targets set to be achieved. This revenue-gap distorts the
whole system and the economy disturbing all the major macroeconomic
indicators. This study is aimed to find out short and long
term impact of revenue gap on budget deficit, debt burden and
economic growth on the economy of Pakistan. For this purpose the
study uses autoregressive distributed lag approach to cointegration
and error correction mechanism on three different models for the
period 1980 to 2009. The empirical results show that revenue gap has
a short and long run relationship with economic growth and budget
deficit. However, revenue gap has no impact on debt burden.
Abstract: A double module hollow fiber supported liquid
membrane (HFSLM) was applied to selectively separate lead and
mercury ions from dilute synthetic produced water. The experiments
were investigated on several variables: types of extractants
(D2EHPA, Cyanex 471, Aliquat 336, and TOA), concentration of the
selected extractant and operating time. The results clearly showed
that the double module HFSLM could selectively separate Pb(II) and
Hg(II) in feed solution at a very low concentration to less than the
regulatory discharge limit of 0.2 and 0.005 mg/L issued by the
Ministry of Industry and the Ministry of Natural Resource
Environment, Thailand. The highest extractions of lead and mercury
ions from synthetic produced water were 96% and 100% using 0.03
M D2EHPA and 0.06 M Aliquat 336 as the extractant for the first
and second modules.
Abstract: This paper presents the significant factor and give
some suggestion that should know before design. The main objective of this paper is guide the first step for someone who attends to design of grounding system before study in details later. The overview of
grounding system can protect damage from fault such as can save a human life and power system equipment. The unsafe conditions have
three cases. Case 1) maximum touch voltage exceeds the safety
criteria. In this case, the conductor compression ratio of the ground gird should be first adjusted to have optimal spacing of ground grid
conductors. If it still over limit, earth resistivity should be consider afterward. Case 2) maximum step voltage exceeds the safety criteria.
In this case, increasing the number of ground grid conductors around
the boundary can solve this problem. Case 3) both of maximum touch
and step voltage exceed the safety criteria. In this case, follow the solutions explained in case 1 and case 2. Another suggestion, vary depth of ground grid until maximum step and touch voltage do not
exceed the safety criteria.
Abstract: This study investigates the relationship between 10
year bond value, Yen/U.S dollar exchange rate, non-farm payrolls (all
employs) and crude oil to U.S. Dow Jones Sustainability Index. A
GARCH model is used to test these relationships for the period
January 1st 1999 to January 31st 2008 using monthly data. Results
show that an increase of the 10 year bond and non farm payrolls (all
employs) lead to an increase of the D.J.S.I returns. On the contrary
the volatility of the Yen/U.S dollar exchange rates as well as the
increase of crude oil returns has negative effects on the U.S D.J.S.I
returns. This study aims at assisting investors to understand the
influences certain macroeconomic indicators have on the companies-
stock returns as reported by the D.J.S.I.
Abstract: Artifact rejection plays a key role in many signal processing applications. The artifacts are disturbance that can occur during the signal acquisition and that can alter the analysis of the signals themselves. Our aim is to automatically remove the artifacts, in particular from the Electroencephalographic (EEG) recordings. A technique for the automatic artifact rejection, based on the Independent Component Analysis (ICA) for the artifact extraction and on some high order statistics such as kurtosis and Shannon-s entropy, was proposed some years ago in literature. In this paper we try to enhance this technique proposing a new method based on the Renyi-s entropy. The performance of our method was tested and compared to the performance of the method in literature and the former proved to outperform the latter.
Abstract: A transient finite element model has been developed
to study the heat transfer and fluid flow during spot Gas Tungsten
Arc Welding (GTAW) on stainless steel. Temperature field, fluid
velocity and electromagnetic fields are computed inside the cathode,
arc-plasma and anode using a unified MHD formulation. The
developed model is then used to study the influence of different
helium-argon gas mixtures on both the energy transferred to the
workpiece and the time evolution of the weld pool dimensions. It is
found that the addition of helium to argon increases the heat flux
density on the weld axis by a factor that can reach 6.5. This induces
an increase in the weld pool depth by a factor of 3. It is also found
that the addition of only 10% of argon to helium decreases
considerably the weld pool depth, which is due to the electrical
conductivity of the mixture that increases significantly when argon is
added to helium.
Abstract: This paper presents an optimization technique to economic load dispatch (ELD) problems with considering the daily load patterns and generator constraints using a particle swarm optimization (PSO). The objective is to minimize the fuel cost. The optimization problem is subject to system constraints consisting of power balance and generation output of each units. The application of a constriction factor into PSO is a useful strategy to ensure convergence of the particle swarm algorithm. The proposed method is able to determine, the output power generation for all of the power generation units, so that the total constraint cost function is minimized. The performance of the developed methodology is demonstrated by case studies in test system of fifteen-generation units. The results show that the proposed algorithm scan give the minimum total cost of generation while satisfying all the constraints and benefiting greatly from saving in power loss reduction
Abstract: The goal of this work is to improve the efficiency and the reliability of the automatic artifact rejection, in particular from the Electroencephalographic (EEG) recordings. Artifact rejection is a key topic in signal processing. The artifacts are unwelcome signals that may occur during the signal acquisition and that may alter the analysis of the signals themselves. A technique for the automatic artifact rejection, based on the Independent Component Analysis (ICA) for the artifact extraction and on some high order statistics such as kurtosis and Shannon-s entropy, was proposed some years ago in literature. In this paper we enhance this technique introducing the Renyi-s entropy. The performance of our method was tested exploiting the Independent Component scalp maps and it was compared to the performance of the method in literature and it showed to outperform it.
Abstract: A water surface slope limiting scheme is tested and
compared with the water depth slope limiter for the solution of one
dimensional shallow water equations with bottom slope source term.
Numerical schemes based on the total variation diminishing Runge-
Kutta discontinuous Galerkin finite element method with slope
limiter schemes based on water surface slope and water depth are
used to solve one-dimensional shallow water equations. For each
slope limiter, three different Riemann solvers based on HLL, LF, and
Roe flux functions are used. The proposed water surface based slope
limiter scheme is easy to implement and shows better conservation
property compared to the slope limiter based on water depth. Of the
three flux functions, the Roe approximation provides the best results
while the LF function proves to be least suitable when used with
either slope limiter scheme.
Abstract: The general global behavior of particle S a non-linear (Q - xy)2 potential cannot be revealed a Poincare surface of section method (PSS) because inost trajectories take practically infinitely long time to integrate numerically before they come back to the surface. In this study as an alternative to PSS, a multiple scale perturbation is applied to analyze global adiabatic, non-adiabatic and chaotic behavior of particles in this potential. It was found that the results can be summarized as a form of a Fermi-like map. Additionally, this method gives a variation of global stochasticity criteria with Q.
Abstract: In this paper, one-dimensional analysis of flow in a
single-stage gas gun is conducted. The compressible inviscid flow
equations are numerically solved by the second-order Roe TVD
method, by using moving boundaries. For investigation of real gas
effect the Noble-Able equation is applied. The numerical results are
compared with the experimental data to validate the numerical
scheme. The results show that with using the Noble-Able equation,
the muzzle velocity decreases.
Abstract: Yam starch obtained from the water yam (munlued)
by the wet milling process was studied for some physicochemical
properties. Yam starch film was prepared by casting using glycerol as
a plasticizer. The effect of different glycerol (1.30, 1.65 and
2.00g/100g of filmogenic solution) and starch concentrations (3.30,
3.65 and 4.00g /100g of filmogenic solution) were evaluated on some
characteristics of the film. The temperature for obtaining the
gelatinized starch solution was 70-80°C and then dried at 45°C for 4
hours. The resulting starch from munlued granular morphology was
triangular and the average size of the granule was 26.68 μm. The
amylose content by colorimetric method was 26 % and the gelatinize
temperature was 70-80°C. The appearance of the film was smooth,
transparent, and glossy with average moisture content of 25.96% and
thickness of 0.01mm. Puncture deformation and flexibility increased
with glycerol content. The starch and glycerol concentration were a
significant factor of the yam starch film characteristics. Yam starch
film can be described as a biofilm providing many applications and
developments with the advantage of biodegradability.
Abstract: Basel III (or the Third Basel Accord) is a global
regulatory standard on bank capital adequacy, stress testing and
market liquidity risk agreed upon by the members of the Basel
Committee on Banking Supervision in 2010-2011, and scheduled to
be introduced from 2013 until 2018. Basel III is a comprehensive set
of reform measures. These measures aim to; (1) improve the banking
sector-s ability to absorb shocks arising from financial and economic
stress, whatever the source, (2) improve risk management and
governance, (3) strengthen banks- transparency and disclosures.
Similarly the reform target; (1) bank level or micro-prudential,
regulation, which will help raise the resilience of individual banking
institutions to periods of stress. (2) Macro-prudential regulations,
system wide risk that can build up across the banking sector as well
as the pro-cyclical implication of these risks over time. These two
approaches to supervision are complementary as greater resilience at
the individual bank level reduces the risk system wide shocks.
Macroeconomic impact of Basel III; OECD estimates that the
medium-term impact of Basel III implementation on GDP growth is
in the range -0,05 percent to -0,15 percent per year. On the other hand
economic output is mainly affected by an increase in bank lending
spreads as banks pass a rise in banking funding costs, due to higher
capital requirements, to their customers. Consequently the estimated
effects on GDP growth assume no active response from monetary
policy. Basel III impact on economic output could be offset by a
reduction (or delayed increase) in monetary policy rates by about 30
to 80 basis points. The aim of this paper is to create a framework
based on the recent regulations in order to prevent financial crises.
Thus the need to overcome the global financial crisis will contribute
to financial crises that may occur in the future periods. In the first
part of the paper, the effects of the global crisis on the banking
system examine the concept of financial regulations. In the second
part; especially in the financial regulations and Basel III are analyzed.
The last section in this paper explored the possible consequences of
the macroeconomic impacts of Basel III.
Abstract: Variable speed drives are growing and varying. Drives expanse depend on progress in different part of science like power system, microelectronic, control methods, and so on. Artificial intelligent contains hard computation and soft computation. Artificial intelligent has found high application in most nonlinear systems same as motors drive. Because it has intelligence like human but there are no sentimental against human like angriness and.... Artificial intelligent is used for various points like approximation, control, and monitoring. Because artificial intelligent techniques can use as controller for any system without requirement to system mathematical model, it has been used in electrical drive control. With this manner, efficiency and reliability of drives increase and volume, weight and cost of them decrease.
Abstract: Today, numerical simulation is a powerful tool to
solve various hydraulic engineering problems. The aim of this
research is numerical solutions of shallow water equations using
finite volume method for Simulations of dam break over wet and dry
bed. In order to solve Riemann problem, Roe-s approximate solver is
used. To evaluate numerical model, simulation was done in 1D and
2D states. In 1D state, two dam break test over dry bed (with and
without friction) were studied. The results showed that Structural
failure around the dam and damage to the downstream constructions
in bed without friction is more than friction bed. In 2D state, two
tests for wet and dry beds were done. Generally in wet bed case,
waves are propagated to canal sides but in dry bed it is not
significant. Therefore, damage to the storage facilities and
agricultural lands in wet bed case is more than in dry bed.
Abstract: This study investigated the pattern and seasonal index of influenza cases in Thailand. Our results showed that southern Thailand had the highest influenza incidence among the four regions of Thailand (i.e. north, northeast, central and southern Thailand). The influenza pattern in southern Thailand was similar to that of northeastern Thailand. Seasonal index values of influenza cases in Thailand were higher in the hot season than in the wet season. Influenza cases started to increase at the beginning of the hot season (April), reached a maximum in August, rapidly declined in the middle of the wet season and reached the lowest value in December. Seasonal index values for northern Thailand differed from other regions of Thailand.
Abstract: This paper shows that the economy of any country
can be presented as three different shells such as: economic shell of a
big, a medium and a small business. The new concepts were
introduced such as: volume of an economic shell, coefficient of
shell-s expansion (compression) etc. These shells can expansion or
compress under action by internal or external powers and when shell
expansions - it means the rising of a business activity and
compression shows us that economy goes on recession. This process
of an expansion or a compression can develop in the various ways
like linear, logarithm or any other mathematical laws.