Abstract: This study models the use of transcutaneous electrical
nerve stimulation on skin with a disk electrode in order to simulate
tissue damage. The current density distribution above a disk electrode
is known to be a dynamic and non-uniform quantity that is intensified
at the edges of the disk. The non-uniformity is subject to change
through using various electrode geometries or stimulation methods.
One of these methods known as edge-retarded stimulation has shown
to reduce this edge enhancement. Though progress has been made in
modeling the behavior of a disk electrode, little has been done to test
the validity of these models in simulating the actual heat transfer
from the electrode. This simulation uses finite element software to
couple the injection of current from a disk electrode to heat transfer
described by the Pennesbioheat transfer equation. An example
application of this model is studying an experimental form of
stimulation, known as edge-retarded stimulation. The edge-retarded
stimulation method will reduce the current density at the edges of the
electrode. It is hypothesized that reducing the current density edge
enhancement effect will, in turn, reduce temperature change and
tissue damage at the edges of these electrodes. This study tests this
hypothesis as a demonstration of the capabilities of this model. The
edge-retarded stimulation proved to be safer after this simulation. It is
shown that temperature change and the fraction of tissue necrosis is
much greater in the square wave stimulation. These results bring
implications for changes of procedures in transcutaneous electrical
nerve stimulation and transcutaneous spinal cord stimulation as well.
Abstract: We used high-precision Global Positioning System
(GPS) to geodetically constrain the motion of stations in the
Darjiling-Sikkim Himalayan (DSH) wedge and examine the
deformation at the Indian-Tibetan plate boundary using IGS
(International GPS Service) fiducial stations. High-precision GPS
based displacement and velocity field was measured in the DSH
between 1997 and 2009. To obtain additional insight north of the
Indo-Tibetan border and in the Darjiling-Sikkim-Tibet (DaSiT)
wedge, published velocities from four stations J037, XIGA, J029 and
YADO were also included in the analysis. India-fixed velocities or
the back-slip was computed relative to the pole of rotation of the
Indian Plate (Latitude 52.97 ± 0.22º, Longitude - 0.30 ± 3.76º, and
Angular Velocity 0.500 ± 0.008º/ Myr) in the DaSiT wedge.
Dislocation modelling was carried out with the back-slip to model the
best possible solution of a finite rectangular dislocation or the
causative fault based on dislocation theory that produced the
observed back-slip using a forward modelling approach. To find the
best possible solution, three different models were attempted. First,
slip along a single thrust fault, then two thrust faults and in finally,
three thrust faults were modelled to simulate the back-slip in the
DaSiT wedge. The three-fault case bests the measured displacements
and is taken as the best possible solution.
Abstract: In order to evaluate the performance of a unified power
flow controller (UPFC), mathematical models for steady state and
dynamic analysis are to be developed. The steady state model is
mainly concerned with the incorporation of the UPFC in load flow
studies. Several load flow models for UPFC have been introduced
in literature, and one of the most reliable models is the decoupled
UPFC model. In spite of UPFC decoupled load flow model simplicity,
it is more robust compared to other UPFC load flow models and it
contains unique capabilities. Some shortcoming such as additional
set of nonlinear equations are to be solved separately after the load
flow solution is obtained. The aim of this study is to investigate the
different control strategies that can be realized in the decoupled load
flow model (individual control and combined control), and the impact
of the location of the UPFC in the network on its control parameters.
Abstract: Most flexible rotors can be considered as beam-like
structures. In many cases, rotors are modeled as one-dimensional
bodies, made basically of beam-like shafts with rigid bodies attached
to them. This approach is typical of rotor dynamics, both analytical
and numerical, and several rotor dynamic codes, based on the finite
element method, follow this trend. In this paper, a finite element
model based on Timoshenko beam elements is utilized to analyze the
lateral dynamic behavior of a certain rotor-bearing system in
operating conditions.
Abstract: This work presents the modelling and simulation of
saponification of ethyl acetate in the presence of sodium hydroxide in
a plug flow reactor using Aspen Plus simulation software. Plug flow
reactors are widely used in the industry due to the non-mixing
property. The use of plug flow reactors becomes significant when
there is a need for continuous large scale reaction or fast reaction.
Plug flow reactors have a high volumetric unit conversion as the
occurrence for side reactions is minimum. In this research Aspen Plus
V8.0 has been successfully used to simulate the plug flow reactor. In
order to simulate the process as accurately as possible HYSYS Peng-
Robinson EOS package was used as the property method. The results
obtained from the simulation were verified by the experiment carried
out in the EDIBON plug flow reactor module. The correlation
coefficient (r2) was 0.98 and it proved that simulation results
satisfactorily fit for the experimental model. The developed model
can be used as a guide for understanding the reaction kinetics of a
plug flow reactor.
Abstract: It is known that residual welding deformations give
negative effect to processability and operational quality of welded
structures, complicating their assembly and reducing strength.
Therefore, selection of optimal technology, ensuring minimum
welding deformations, is one of the main goals in developing a
technology for manufacturing of welded structures.
Through years, JSC SSTC has been developing a theory for
estimation of welding deformations and practical activities for
reducing and compensating such deformations during welding
process. During long time a methodology was used, based on analytic
dependence. This methodology allowed defining volumetric changes
of metal due to welding heating and subsequent cooling. However,
dependences for definition of structures deformations, arising as a
result of volumetric changes of metal in the weld area, allowed
performing calculations only for simple structures, such as units, flat
sections and sections with small curvature. In case of complex 3D
structures, estimations on the base of analytic dependences gave
significant errors.
To eliminate this shortage, it was suggested to use finite elements
method for resolving of deformation problem. Here, one shall first
calculate volumes of longitudinal and transversal shortenings of
welding joints using method of analytic dependences and further,
with obtained shortenings, calculate forces, which action is
equivalent to the action of active welding stresses. Further, a finiteelements
model of the structure is developed and equivalent forces
are added to this model. Having results of calculations, an optimal
sequence of assembly and welding is selected and special measures to
reduce and compensate welding deformations are developed and
taken.
Abstract: Electronic market place plays an important
intermediary role for connecting dealers and retail customers. The
main aim of this paper is to design a value co-creation model in
used-car auctions. More specifically, the study has been designed in
order to describe the process of value co-creation in used-car auctions,
to explore the co-created values in used-car auctions, and finally
conclude the paper indicating the future research directions. Our
analysis shows that economic values as well as non-economic values
are co-created in used-car auctions. In addition, this paper contributes
to the academic society broadening the view of value co-creation in
service science.
Abstract: Disasters are quite experienced in our days. They are
caused by floods, landslides, and building fires that is the main
objective of this study. To cope with these unexpected events,
precautions must be taken to protect human lives. The emphasis on
disposal work focuses on the resolution of the evacuation problem in
case of no-notice disaster. The problem of evacuation is listed as a
dynamic network flow problem. Particularly, we model the
evacuation problem as an earliest arrival flow problem with load
dependent transit time. This problem is classified as NP-Hard. Our
challenge here is to propose a metaheuristic solution for solving the
evacuation problem. We define our objective as the maximization of
evacuees during earliest periods of a time horizon T. The objective
provides the evacuation of persons as soon as possible. We
performed an experimental study on emergency evacuation from the
tunisian children’s hospital. This work prompts us to look for
evacuation plans corresponding to several situations where the
network dynamically changes.
Abstract: This paper presents the application of finite dynamic
programming, specifically the "Markov Chain" model, as part of the
decision making process of a company in the cosmetics sector located
in the vicinity of Bogota DC. The objective of this process was to
decide whether the company should completely reconstruct its
wastewater treatment plant or instead optimize the plant through the
addition of equipment. The goal of both of these options was to make
the required improvements in order to comply with parameters
established by national legislation regarding the treatment of waste
before it is released into the environment. This technique will allow
the company to select the best option and implement a solution for
the processing of waste to minimize environmental damage and the
acquisition and implementation costs.
Abstract: Artificial Neural Networks (ANN) trained using backpropagation
(BP) algorithm are commonly used for modeling
material behavior associated with non-linear, complex or unknown
interactions among the material constituents. Despite multidisciplinary
applications of back-propagation neural networks
(BPNN), the BP algorithm possesses the inherent drawback of
getting trapped in local minima and slowly converging to a global
optimum. The paper present a hybrid artificial neural networks and
genetic algorithm approach for modeling slump of ready mix
concrete based on its design mix constituents. Genetic algorithms
(GA) global search is employed for evolving the initial weights and
biases for training of neural networks, which are further fine tuned
using the BP algorithm. The study showed that, hybrid ANN-GA
model provided consistent predictions in comparison to commonly
used BPNN model. In comparison to BPNN model, the hybrid ANNGA
model was able to reach the desired performance goal quickly.
Apart from the modeling slump of ready mix concrete, the synaptic
weights of neural networks were harnessed for analyzing the relative
importance of concrete design mix constituents on the slump value.
The sand and water constituents of the concrete design mix were
found to exhibit maximum importance on the concrete slump value.
Abstract: Construction in Finland is focusing increasingly on
renovation instead of conventional new construction, and this trend
will continue to grow in the coming years and decades. Renovation of
the large number of suburban residential apartment buildings built in
the 1960s and 1970s poses a particular challenge. However,
renovation projects are demanding for the residents of these
buildings, since they usually are uninitiated in construction issues. On
the other hand, renovation projects generally apply the operating
models of new construction.
Nevertheless, the residents of an existing residential apartment
building are some of the best experts on the site. Thus, in this
research project we applied a relational model in developing and
testing at case sites a planning process that employs interactive
planning methods. Current residents, housing company managers, the
city zoning manager, the contractor’s and prefab element supplier’s
representatives, professional designers and researchers all took part in
the planning. The entire interactive planning process progressed
phase by phase as the participants’ and designers’ concerted
discussion and ideation process, so that the end result was a
renovation plan desired by the residents.
Abstract: The study examines the influence of marital status on
consumers of products and services using blogs as a source of
information. A pre-designed questionnaire was used to collect the
primary data from the respondents (experiences). Data were collected
from one hundred and eighty seven respondents residing in and
around the Emirates of Sharjah and Dubai of the United Arab
Emirates. The collected data was analyzed with the help of statistical
tools such as averages, percentages, factor analysis, Student’s t-test
and Structural Equation Modelling Technique.
Objectives of the study are to know the reasons how married and
unmarried or single consumers of products and services are
motivated to use blogs as a source of information, to know whether
the consumers of products and services irrespective of their marital
status share their views and experiences with other bloggers and to
know the respondents’ future intentions towards blogging.
The study revealed the following: Majority of the respondents
have the motivation to blog because they are willing to receive
comments on what they post about services, convenience of blogs to
search for information about services and products, by blogging
respondents share information on the symptoms of a disease/ disorder
that may be experienced by someone, helps to share information
about ready to cook mix products and are keen to spend more time
blogging in the future.
Abstract: This paper presents a regression model with
autocorrelated errors in which the inputs are social moods obtained by
analyzing the adjectives in Twitter posts using a document topic
model, where document topics are extracted using LDA. The
regression model predicts Dow Jones Industrial Average (DJIA) more
precisely than autoregressive moving-average models.
Abstract: Abundant and cheap agricultural waste of oil palm trunk (OPT) juice was used to produce bioethanol. Two strains of Saccharomyces cerevisiae and a strain of Pichia stipitis were used to produce bioethanol from the OPT juice. Fermentation was conducted at previously optimized condition at 30oC and without shaking. The kinetic parameters were estimated and calculated. Monod equation and Hinshelwood model is used to relate the specific growth to the concentration of the limiting substrate and also to simulate bioethanol production rate. Among the three strains, single S. cerevisiae Kyokai no. 7 produce the highest ethanol yield of 0.477 g/l.h within the shortest time (12 h). This yeast also produces more than 20 g/l ethanol concentration within 10 h of fermentation.
Abstract: There is an essential need for obtaining the mathematical representation of fish body undulations, which can be used for designing and building new innovative types of marine propulsion systems with less environmental impact. This research work presents a case study to derive the mathematical model for fish body movement. Observation and capturing image methods were used in this study in order to obtain a mathematical representation of Clariasbatrachus fish (catfish). An experiment was conducted by using an aquarium with dimension 0.609 m x 0.304 m x 0.304 m, and a 0.5 m ruler was attached at the base of the aquarium. Progressive Scan Monochrome Camera was positioned at 1.8 m above the base of the aquarium to provide swimming sequences. Seven points were marked on the fish body using white marker to indicate the fish movement and measuring the amplitude of undulation. Images from video recordings (20 frames/s) were analyzed frame by frame using local coordinate system, with time interval 0.05 s. The amplitudes of undulations were obtained for image analysis from each point that has been marked on fish body. A graph of amplitude of undulations versus time was plotted by using computer to derive a mathematical fit. The function for the graph is polynomial with nine orders.
Abstract: An extensive amount of work has been done in data
clustering research under the unsupervised learning technique in Data
Mining during the past two decades. Moreover, several approaches
and methods have been emerged focusing on clustering diverse data
types, features of cluster models and similarity rates of clusters.
However, none of the single clustering algorithm exemplifies its best
nature in extracting efficient clusters. Consequently, in order to
rectify this issue, a new challenging technique called Cluster
Ensemble method was bloomed. This new approach tends to be the
alternative method for the cluster analysis problem. The main
objective of the Cluster Ensemble is to aggregate the diverse
clustering solutions in such a way to attain accuracy and also to
improve the eminence the individual clustering algorithms. Due to
the massive and rapid development of new methods in the globe of
data mining, it is highly mandatory to scrutinize a vital analysis of
existing techniques and the future novelty. This paper shows the
comparative analysis of different cluster ensemble methods along
with their methodologies and salient features. Henceforth this
unambiguous analysis will be very useful for the society of clustering
experts and also helps in deciding the most appropriate one to resolve
the problem in hand.
Abstract: Fluid rheology may have essential impact on sound propagation in a liquid-filled pipe, especially, in a low frequency range. Rheological parameters of liquid are temperature-sensitive, which ultimately results in a temperature dependence of the wave speed and attenuation in the waveguide. The study is devoted to modeling of this effect at sound propagation in an elastic pipe with polymeric liquid, described by generalized Maxwell model with non-zero high-frequency viscosity. It is assumed that relaxation spectrum is distributed according to the Spriggs law; temperature impact on the liquid rheology is described on the basis of the temperature-superposition principle and activation theory. The dispersion equation for the waveguide, considered as a thin-walled tube with polymeric solution, is obtained within a quasi-one-dimensional formulation. Results of the study illustrate the influence of temperature on sound propagation in the system.
Abstract: This paper presents the electrical effect of two neighboring distribution substation during the construction phase. The size of auxiliary grounding grid have an effect on entire grounding system. The bigger the size of auxiliary grounding grid, the lower the GPR and maximum touch voltage, with the exception that when the two grids are unconnected, i.e. the bigger the size of auxiliary grounding grid, the higher the maximum step voltage. The results in this paper could be served as design guideline of grounding system, and perhaps remedy of some troublesome grounding grids in power distribution’s system. Modeling and simulation is carried out on the Current Distribution Electromagnetic interference Grounding and Soil structure (CDEGS) program. The simulation results exhibit the design and analysis of power system grounding and perhaps could be set as a standard in grounding system design and modification in distribution substations.
Abstract: In this paper, we present a new maintenance model
for a partially observable system subject to two failure modes,
namely a catastrophic failure and a failure due to the system
degradation. The system is subject to condition monitoring and the
degradation process is described by a hidden Markov model. A
cost-optimal Bayesian control policy is developed for maintaining
the system. The control problem is formulated in the semi-Markov
decision process framework. An effective computational algorithm is
developed, illustrated by a numerical example.
Abstract: In this paper the vibration of a synchronous belt drive
during start-up is analyzed and discussed. Besides considering the
belt elasticity, the model here proposed also takes into consideration
the electromagnetic response of the DC motor. The solution of the
motion equations is obtained by means of the modal analysis in
state space, which allows to obtain the decoupling of all equations,
without introducing the hypothesis of proportional damping. The
mathematical model of the transmission and the solution algorithms
have been implemented within a computing software that allows the
user to simulate the dynamics of the system and to evaluate the effects
due to the elasticity of the belt branches and to the electromagnetic
behavior of the DC motor. In order to show the details of the
calculation procedure, the paper presents a case study developed with
the aid of the above-mentioned software.