Abstract: To maximise furnace production it-s necessary to
optimise furnace control, with the objectives of achieving maximum
power input into the melting process, minimum network distortion
and power-off time, without compromise on quality and safety. This
can be achieved with on the one hand by an appropriate electrode
control and on the other hand by a minimum of AC transformer
switching.
Electrical arc is a stochastic process; witch is the principal cause
of power quality problems, including voltages dips, harmonic
distortion, unbalance loads and flicker. So it is difficult to make an
appropriate model for an Electrical Arc Furnace (EAF). The factors
that effect EAF operation are the melting or refining materials,
melting stage, electrode position (arc length), electrode arm control
and short circuit power of the feeder. So arc voltages, current and
power are defined as a nonlinear function of the arc length. In this
article we propose our own empirical function of the EAF and model,
for the mean stages of the melting process, thanks to the
measurements in the steel factory.
Abstract: In the paper the research of flat textile products for use
as electrodes was presented. Material-s resistance measurements were
carried out to determine the suitability of the textiles. Based on the received results of studies different types of textile electrodes were
designed. Textile electrodes tests were carried out on human
phantoms. The electro-conductive properties of human forearm
phantom were also described. Based on this results special electroconductive
hydrogels with electro-conductive particles were feasible. The hydrogel is an important element of the forearm-s phantom
model of a survey of electrodes for muscle electrostimulation. The
hydrogel is an equivalent human skin and tissue. The hydrogel should
have a permanence and recurrence of the electro-conductive properties.
Abstract: A power cable is widely used for power supply in
power distributing networks and power transmission lines. Due to
limitations in the production, delivery and setting up power cables,
they are produced and delivered in several separate lengths. Cable
itself, consists of two cable terminations and arbitrary number of
cable joints, depending on the cable route length. Electrical stress
control is needed to prevent a dielectric breakdown at the end of the
insulation shield in both the air and cable insulation. Reliability of
cable joint depends on its materials, design, installation and operating
environment. The paper describes design and performance results for
new modeled cable joints. Design concepts, based on numerical
calculations, must be correct. An Equivalent Electrodes
Method/Boundary Elements Method-hybrid approach that allows
electromagnetic field calculations in multilayer dielectric media,
including inhomogeneous regions, is presented.
Abstract: Biodiesel production results in glycerol production as
the main by-product in biodiesel industry.One of the utilizations of
glycerol obtained from biodiesel production is as a cement grinding
aid (CGA). Results showed that crude glycerol content was 40.19%
whereas pure glycerol content was 82.15%. BSS value of the cement
with CGA supplementation was higher than that of nonsupplemented
cement (blank) indicating that CGA-supplemented
cement had higher fineness than the non-supplemented one. It was
also found that pure glycerol 95% and TEA 5% at 80ºC was the
optimum CGA used to result in finest cement with BSS value of
4.836 cm2/g. Residue test showed that the smallest percent residue
value (0.11%) was obtained in cement with supplementation of pure
glycerol 95% and TEA 5%. Results of residue test confirmed those of
BSS test showing that cement with supplementation of pure glycerol
95% and TEA 5% had the finest particle size.
Abstract: People from different cultures favor web pages
characterized by the values of their culture and, therefore, tend to
prefer different characteristics of a website according to their cultural
values in terms of navigation, security, product information, customer
service, shopping and design tools. For a company aiming to
globalize its market it is useful to implement country specific cultural
interfaces and different web sites for countries with different cultures.
This paper, following the conclusions proposed by two models of
Hall and Hofstede, and the studies of Marcus and Gould, defines,
through an empirical analysis, the guidelines of web design for both
the Scandinavian countries and Malaysia.
Abstract: The aim of this work is to study the possible use of
stone cutting sludge waste in concrete production, which would
reduce both the environmental impact and the production cost .Slurry
sludge was used a source of water in concrete production, which was
obtained from Samara factory/Jordan, The physico-chemical and
mineralogical characterization of the sludge was carried out to
identify the major components and to compare it with the typical
sand used to produce concrete. Samples analysis showed that 96% of
slurry sludge volume is water, so it should be considered as an
important source of water. Results indicated that the use of slurry
sludge as water source in concrete production has insignificant effect
on compression strength, while it has a sharp effect on the slump
values. Using slurry sludge with a percentage of 25% of the total
water content obtained successful concrete samples regarding slump
and compression tests. To clarify slurry sludge, settling process can
be used to remove the suspended solid. A settling period of 30 min.
obtained 99% removal efficiency. The clarified water is suitable for
using in concrete mixes, which reduce water consumption, conserve
water recourses, increase the profit, reduce operation cost and save
the environment. Additionally, the dry sludge could be used in the
mix design instead of the fine materials with sizes < 160 um. This
application could conserve the natural materials and solve the
environmental and economical problem caused by sludge
accumulation.
Abstract: REY area has been located in Tehran Province and several archaeological ruins of this area indicate that the settlement in this area has been started since several thousand years ago. In this paper, the main investigation items consist of analysis of oil components and groundwater quality inside the wells. By finding the contents of oil in the well, it is possible to find out the pollution source by comparing the oil contents of well with other oil products that are used inside and outside of the oil farm. Investigation items consist of analysis of BTEX (Benzene, Toluene, Ethyl-benzene, Xylene), Gas chromatographic distillation characteristics, Water content, Density, Sulfur content, Lead content, Atmospheric distillation, MTBE(Methyl tertiary butyl ether). Analysis of polluting oil components showed that except MW(Monitoring Well)10 and MW 15 that oil with slightly heavy components was detected in them; with a high possibility the polluting oil is light oil.
Abstract: The forming process parameters of Selective Laser
Sintering(SLS) directly affect the forming efficiency and forming
quality. Therefore, to determine reasonable process parameters is
particularly important. In this paper, the weight of each target of the
forming quality and efficiency is firstly calculated with the Analytic
Hierarchy Process. And then the size of each target is measured by
orthogonal experiment. Finally, the sum of the product of each target
with the weight is compared to the process parameters in each group
and obtained the optimal molding process parameters.
Abstract: The paper provides the basic overview of simulation optimization. The procedure of its practical using is demonstrated on the real example in simulator Witness. The simulation optimization is presented as a good tool for solving many problems in real praxis especially in production systems. The authors also characterize their own experiences and they mention the strengths and weakness of simulation optimization.
Abstract: This article describes the aspects of the formation of
the national idea and national identity through the prism of gender
control and its contradistinction to the obsolete, Soviet component.
The role of females in ethnic and national projects is considered from
the point of view of Dr. Nira Yuval-Davis: as biological reproducers
of the ethnic communities- members; as reproducers of the boarders
of ethnic/national groups; as central participants in the ideological
reproduction of community and transducers of its culture; as symbols
in ideology, reproduction and transformation of ethnic/national
categories; and as participants of national, economical, political and
military combats. The society of the transitional type uses the
symbolic resources of the formation of gender component in the
national project. The gender patterns act like cultural codes,
executing the important ideological function in formation of the
national female- image, i.e. the discussion on hijab - it-s not just the
discussion on control over the female body, it-s the discussion on the
metaphor of social order.
Abstract: During recent years wind turbine technology has
undergone rapid developments. Growth in size and the optimization
of wind turbines has enabled wind energy to become increasingly
competitive with conventional energy sources. As a result today-s
wind turbines participate actively in the power production of several
countries around the world. These developments raise a number of
challenges to be dealt with now and in the future. The penetration of
wind energy in the grid raises questions about the compatibility of the
wind turbine power production with the grid. In particular, the
contribution to grid stability, power quality and behavior during fault
situations plays therefore as important a role as the reliability. In the
present work, we addressed two fault situations that have shown their
influence on the generator and the behavior of the wind over the
defects which are briefly discussed based on simulation results.
Abstract: An integrated Artificial Neural Network- Particle Swarm Optimization (PSO) is presented for analyzing global electricity consumption. To aim this purpose, following steps are done: STEP 1: in the first step, PSO is applied in order to determine world-s oil, natural gas, coal and primary energy demand equations based on socio-economic indicators. World-s population, Gross domestic product (GDP), oil trade movement and natural gas trade movement are used as socio-economic indicators in this study. For each socio-economic indicator, a feed-forward back propagation artificial neural network is trained and projected for future time domain. STEP 2: in the second step, global electricity consumption is projected based on the oil, natural gas, coal and primary energy consumption using PSO. global electricity consumption is forecasted up to year 2040.
Abstract: Ethanol has been known for a long time, being
perhaps the oldest product obtained through traditional biotechnology
fermentation. Agriculture waste as substrate in fermentation is vastly
discussed as alternative to replace edible food and utilization of
organic material. Pineapple peel, highly potential source as substrate
is a by-product of the pineapple processing industry. Bio-ethanol
from pineapple (Ananas comosus) peel extract was carried out by
controlling fermentation without any treatment. Saccharomyces
ellipsoides was used as inoculum in this fermentation process as it is
naturally found at the pineapple skin. In this study, the capability of
Response Surface Methodology (RSM) for optimization of ethanol
production from pineapple peel extract using Saccharomyces
ellipsoideus in batch fermentation process was investigated. Effect of
five test variables in a defined range of inoculum concentration 6-
14% (v/v), pH (4.0-6.0), sugar concentration (14-22°Brix),
temperature (24-32°C) and time of incubation (30-54 hrs) on the
ethanol production were evaluated. Data obtained from experiment
were analyzed with RSM of MINITAB Software (Version 15)
whereby optimum ethanol concentration of 8.637% (v/v) was
determined. The optimum condition of 14% (v/v) inoculum
concentration, pH 6, 22°Brix, 26°C and 30hours of incubation. The
significant regression equation or model at the 5% level with
correlation value of 99.96% was also obtained.
Abstract: The paper proposes the novel design of a 3T XOR gate combining complementary CMOS with pass transistor logic. The design has been compared with earlier proposed 4T and 6T XOR gates and a significant improvement in silicon area and power-delay product has been obtained. An eight transistor full adder has been designed using the proposed three-transistor XOR gate and its performance has been investigated using 0.15um and 0.35um technologies. Compared to the earlier designed 10 transistor full adder, the proposed adder shows a significant improvement in silicon area and power delay product. The whole simulation has been carried out using HSPICE.
Abstract: Using the animations video of teaching materials is an
effective learning method. However, we thought that more effective learning method is to produce the teaching video by learners
themselves. The learners who act as the producer must learn and understand well to produce and present video of teaching materials to
others. The purpose of this study is to propose the project based learning (PBL) technique by co-producing video of IT (information
technology) teaching materials. We used the T2V player to produce
the video based on TVML a TV program description language. By
proposed method, we have assigned the learners to produce the
animations video for “National Examination for Information
Processing Technicians (IPA examination)" in Japan, in order to get
them learns various knowledge and skill on IT field. Experimental
result showed that learning effect has occurred at the video production
process that useful for IT personnel resources development.
Abstract: Characterized as rich mineral substances, low
temperature, few bacteria, and stability with numerous implementation
aspects on aquaculture, food, drinking, and leisure, the deep sea water
(DSW) development has become a new industry in the world. It has
been report that marine algae contain various biologically active
compounds. This research focued on the affections in cultivating
Sagrassum cristaefolium with different concentration of deep sea
water(DSW) and surface sea water(SSW). After two and four weeks,
the total phenolic contents were compared in Sagrassum cristaefolium
culturing with different ways, and the reductive activity of them was
also be tried with potassium ferricyanide. Those fresh seaweeds were
dried with oven and were ground to powder. Progressively, the marine
algae we cultured was extracted by water under the condition with
heating them at 90Ôäâ for 1hr.The total phenolic contents were be
executed using Folin–Ciocalteu method. The results were explaining
as follows: the highest total phenolic contents and the best reductive
ability of all could be observed on the 1/4 proportion of DSW to SSW
culturing in two weeks. Furthermore, the 1/2 proportion of DSW to
SSW also showed good reductive ability and plentiful phenolic
compositions. Finally, we confirmed that difference proportion of
DSW and SSW is the major point relating to ether the total phenolic
components or the reductive ability in the Sagrassum cristaefolium. In
the future, we will use this way to mass production the marine algae or
other micro algae on industry applications.
Abstract: The production of activated carbon from low or zero cost of agricultural by-products or wastes has received great attention from academics and practitioners due to its economic and environmental benefits. In the production of bamboo furniture, a significant amount of bamboo waste is inevitably generated. Therefore, this research aimed to prepare activated carbons from bamboo furniture waste by chemical (KOH) activation and determine their properties and adsorption capacities for water treatment. The influence of carbonization time on the properties and adsorption capacities of activated carbons was also investigated. The finding showed that the bamboo-derived activated carbons had microporous characteristics. They exhibited high tendency for the reduction of impurities present in effluent water. Their adsorption capacities were comparable to the adsorption capacity of a commercial activated carbon regarding to the reduction in COD, TDS and turbidity of the effluent water.
Abstract: TiO2 supported nano-ZnO catalyst was prepared by
deposition-precipitation and tested for the trans-esterification
reaction of soybean oil to biodiesel. The TiO2 support stabilized the
nano-ZnO in a dispersed form with limited crystallite size compared
to the unsupported ZnO. The final ZnO dispersion and crystallite size
and the material transfer resistance in the catalyst significantly
influenced the supported nano-ZnO catalyst performance.
Abstract: Warehousing is commonly used in factories for the
storage of products until delivery of orders. As the amount of
products stored increases it becomes tedious to be carried out
manually. In recent years, the manual storing has converted into fully
or partially computer controlled systems, also known as Automated
Storage and Retrieval Systems (AS/RS). This paper discusses an
ASRS system, which was designed such that the best storage location
for the products is determined by utilizing a fuzzy control system.
The design maintains the records of the products to be/already in
store and the storage/retrieval times along with the availability status
of the storage locations. This paper discusses on the maintenance of
the above mentioned records and the utilization of the concept of
fuzzy logic in order to determine the optimum storage location for
the products. The paper will further discuss on the dynamic splitting
and merging of the storage locations depending on the product sizes.
Abstract: Nowadays, many manufacturing companies try to
reinforce their competitiveness or find a breakthrough by considering
collaboration. In Korea, more than 900 manufacturing companies are
using web-based collaboration systems developed by the
government-led project, referred to as i-Manufacturing. The system
supports some similar functions of Product Data Management (PDM)
as well as Project Management System (PMS). A web-based
collaboration system provides many useful functions for collaborative
works. This system, however, does not support new linking services
between buyers and suppliers. Therefore, in order to find new
collaborative partners, this paper proposes a framework which creates
new connections between buyers and suppliers facilitating their
collaboration, referred to as Excellent Manufacturer Scouting System
(EMSS). EMSS plays a role as a bridge between overseas buyers and
suppliers. As a part of study on EMSS, we also propose an evaluation
method of manufacturability of potential partners with six main factors.
Based on the results of evaluation, buyers may get a good guideline to
choose their new partners before getting into negotiation processes
with them.