Abstract: An efficient freeway system will be essential to the
development of Africa, and interchanges are a key to that efficiency.
Around the world, many interchanges between freeways and surface
streets, called service interchanges, are of the diamond configuration,
and interchanges using roundabouts or loop ramps are also popular.
However, many diamond interchanges have serious operational
problems, interchanges with roundabouts fail at high demand levels,
and loops use lots of expensive land. Newer service interchange
designs provide other options. The most popular new interchange
design in the US at the moment is the double crossover diamond
(DCD), also known as the diverging diamond. The DCD has
enormous potential, but also has several significant limitations.
The objectives of this paper are to review new service interchange
options and to highlight some of the main features of those
alternatives. The paper tests four conventional and seven
unconventional designs using seven measures related to efficiency,
cost, and safety.
The results show that there is no superior design in all measures
investigated. The DCD is better than most designs tested on most
measures examined. However, the DCD was only superior to all
other designs for bridge width. The DCD performed relatively poorly
for capacity and for serving pedestrians. Based on the results, African
freeway designers are encouraged to investigate the full range of
alternatives that could work at the spot of interest. Diamonds and
DCDs have their niches, but some of the other designs investigated
could be optimum at some spots.
Abstract: The present study explores flow visualization experiments with various blunt shaped bluff bodies placed inside a circular pipe. The bodies mainly comprise of modifications of trapezoidal cylinder, most widely used in practical applications, such as vortex flowmeters. The present configuration possesses the feature of both internal and external flows with low aspect ratio. The vortex dynamics of bluff bodies in such configuration is seldom reported in the literature. Dye injection technique is employed to visualize the complex vortex formation mechanism behind the bluff bodies. The influence of orientation, slit and after body shape is studied in an attempt to obtain better understanding of the vortex formation mechanism. Various wake parameters like Strouhal number, vortex formation length and wake width are documented for these shapes. Vortex formation both with and without shear layer interaction is observed for most of the shapes.
Abstract: This paper presents an implementation and performance test of a distributed motion control system based on a master-slave configuration used to move a plasma-cutting torch over a predefined trajectory. The master is a general-purpose computer running on an open source operating system platform and software developer. Software running in the master computer generates commands on real time and we measure performance based on a selected set of differences between expected and observed distances. We are testing the null hypothesis that the outcome trajectory is identical to the input against the alternative hypothesis that there is a shift to the right or left of the input one. We used the Wilcoxon signed ranks test method for the hypothesis test.
Abstract: The success of renewable powered electric vehicle
charging station in isolated areas depends highly on the availability
and sustainability of renewable resources all year round at a selected
location. The main focus of this paper is to discuss the possible
charging strategies that could be implemented to find the best
possible configuration of an electric Tuk-Tuk charging station at a
given location within South Africa. The charging station is designed,
modeled and simulated to evaluate its performances. The technoeconomic
analysis of different feasible supply configurations of the
charging station using renewable energies is simulated using
HOMER software and the results compared in order to select the best
possible charging strategies in terms of cost of energy consumed.
Abstract: This paper presents the study of strengthening R/C
beams with large circular and square opening located at flexure zone
by Carbon Fiber Reinforced Polymer (CFRP) laminates. A total of
five beams were tested to failure under four point loading to
investigate the structural behavior including crack patterns, failure
mode, ultimate load and load deflection behaviour. Test results show
that large opening at flexure reduces the beam capacity and stiffness;
and increases cracking and deflection. A strengthening configuration
was designed for each un-strengthened beams based on their
respective crack patterns. CFRP laminates remarkably restore the
beam capacity of beam with large circular opening at flexure location
while 10% re-gain of beam capacity with square opening. The use of
CFRP laminates with the designed strengthening configuration could
significantly reduce excessive cracking and deflection and increase
the ultimate capacity and stiffness of beam.
Abstract: We have investigated statistical properties of the defect turbulence in 1D CGLE wherein many body interaction is involved between local depressing wave (LDW) and local standing wave (LSW). It is shown that the counting number fluctuation of LDW is subject to the sub-Poisson statistics (SUBP). The physical origin of the SUBP can be ascribed to pair extinction of LDWs based on the master equation approach. It is also shown that the probability density function (pdf) of inter-LDW distance can be identified by the hyper gamma distribution. Assuming a superstatistics of the exponential distribution (Poisson configuration), a plausible explanation is given. It is shown further that the pdf of amplitude of LDW has a fattail. The underlying mechanism of its fluctuation is examined by introducing a generalized fractional Poisson configuration.
Abstract: This paper focuses on a critical component of the situational awareness (SA), the control of autonomous vertical flight for vectored thrust aerial vehicle (VTAV). With the SA strategy, we proposed a flight control procedure to address the dynamics variation and performance requirement difference of flight trajectory for an unmanned helicopter model with vectored thrust configuration. This control strategy for chosen model of VTAV has been verified by simulation of take-off and forward maneuvers using software package Simulink and demonstrated good performance for fast stabilization of motors, consequently, fast SA with economy in energy can be asserted during search-and-rescue operations.
Abstract: In this research, STNEP is being studied considering network adequacy and limitation of investment cost by decimal codification genetic algorithm (DCGA). The goal is obtaining the maximum of network adequacy with lowest expansion cost for a specific investment. Finally, the proposed idea is applied to the Garvers 6-bus network. The results show that considering the network adequacy for solution of STNEP problem is caused that among of expansion plans for a determined investment, configuration which has relatively lower expansion cost and higher adequacy is proposed by GA based method. Finally, with respect to the curve of adequacy versus expansion cost it can be said that more optimal configurations for expansion of network are obtained with lower investment costs.
Abstract: In this paper a novel ultra-wideband (UWB) slot antenna with band notch characteristics for world interoperability for microwave access (WiMAX) is proposed. The designed antenna consists of a rectangular radiating patch and a ground plane with tapered shape slot. To realize a notch band, a curved parasitic element has been etched out along with the radiating patch. It is observed that by adjusting the length, thickness and position of the parasitic element, the proposed antenna can achieved an impedance bandwidth of 8.01GHz (2.84 to 10.85GHz) with a notched band of 3.28-3.85GHz. Compared to the recently reported band notch antennas, the proposed antenna has a simple configuration to realize band notch characteristics in order to mitigate the potential interference between WiMAX and UWB system. Furthermore, a stable radiation pattern and moderate gain except at the notched band makes the proposed antenna suitable for various UWB applications.
Abstract: The central recirculation zone (CRZ) in a swirl
stabilized gas turbine combustor has a dominant effect on the fuel air
mixing process and flame stability. Most of state of the art swirlers
share one disadvantage; the fixed swirl number for the same swirler
configuration. Thus, in a mathematical sense, Reynolds number
becomes the sole parameter for controlling the flow characteristics
inside the combustor. As a result, at low load operation, the
generated swirl is more likely to become feeble affecting the flame
stabilization and mixing process. This paper introduces a new swirler
concept which overcomes the mentioned weakness of the modern
configurations. The new swirler introduces air tangentially and
axially to the combustor through tangential vanes and an axial vanes
respectively. Therefore, it provides different swirl numbers for the
same configuration by regulating the ratio between the axial and
tangential flow momenta. The swirler aerodynamic performance was
investigated using four CFD simulations in order to demonstrate the
impact of tangential to axial flow rate ratio on the CRZ. It was found
that the length of the CRZ is directly proportional to the tangential to
axial air flow rate ratio.
Abstract: Automotive suspension system is important part of car
comfort and safety. In this article automotive active suspension with
linear motor as actuator is designed using H-infinity control. This
paper is focused on comparison of different controller designed for
quart, half or full-car model (and always used for “full" car). Special
attention is placed on energy demand of the whole system. Each
controller configuration is simulated and then verified on the
hydraulic quarter car test bed.
Abstract: Microplasma welding is a less expensive alternative to
laser welding in dental technology. The aim of the study was to
highlight discontinuities present in the microplasma welded joints of
dental base metal alloys by visual analysis. Five base metal alloys
designated for fixed prostheses manufacture were selected for the
experiments. Using these plates, preliminary tests were conducted by
microplasma welding in butt joint configuration, without filler
material, bilaterally and with filler material, proper for each base
metal. Macroscopic visual inspection was performed to assess
carefully the irregularities in the welds. Electron microscopy allowed
detection of discontinuities that are not visible to the eye and
revealing details regarding location, trajectory, morphology and size
of discontinuities. Supplementing visual control with microscopic
analysis allows to detect small discontinuities, which escapes the
macroscopic control and to make a detailed study of the weld.
Abstract: Multicarrier transmission system such as Orthogonal
Frequency Division Multiplexing (OFDM) is a promising technique
for high bit rate transmission in wireless communication systems.
OFDM is a spectrally efficient modulation technique that can achieve
high speed data transmission over multipath fading channels without
the need for powerful equalization techniques. A major drawback
of OFDM is the high Peak-to-Average Power Ratio (PAPR) of the
transmit signal which can significantly impact the performance of the
power amplifier. In this paper we have compared the PAPR reduction
performance of Golay and Reed-Muller coded OFDM signal. From
our simulation it has been found that the PAPR reduction performance
of Golay coded OFDM is better than the Reed-Muller coded OFDM
signal. Moreover, for the optimum PAPR reduction performance, code
configuration for Golay and Reed-Muller codes has been identified.
Abstract: This work proposes a set of actions to assist redesign
procedure in existing products of Electric and Electronic Equipment
(EEE). The aim is to improve their environmental behavior after their
withdrawal in the End-of-Life (EOL) phase. In the beginning data
collection takes place. Then follows selection and implementation of
the optimal EOL Treatment Strategy (EOL_TS) and its results-
evaluation concerning the environment. In parallel, product design
characteristics that can be altered are selected based on their
significance for the environment in the EOL stage. All results from
the previous stages are combined and possible redesign actions are
formulated for further examination and afterwards configuration in
the design stage. The applied method to perform these tasks is Lean
Thinking (LT). At the end, results concerning the application of the
proposed method on a distribution transformer are presented.
Abstract: This paper considers the design of a motion planner
that will simultaneously accomplish control and motion planning of a
n-link nonholonomic mobile manipulator, wherein, a n-link
holonomic manipulator is coupled with a nonholonomic mobile
platform, within an obstacle-ridden environment. This planner,
derived from the Lyapunov-based control scheme, generates
collision-free trajectories from an initial configuration to a final
configuration in a constrained environment cluttered with stationary
solid objects of different shapes and sizes. We demonstrate the
efficiency of the control scheme and the resulting acceleration
controllers of the mobile manipulator with results through computer
simulations of an interesting scenario.
Abstract: An exploration in the competency of the optical
multilevel Mapping Multiplexing Technique (MMT) system in
tolerating to the impact of nonlinearities as Self Phase Modulation
(SPM) during the presence of dispersion compensation methods. The
existence of high energy pulses stimulates deterioration in the chirp
compression process attained by SPM which introduces an upper
power boundary limit. An evaluation of the post and asymmetric prepost
fiber compensation methods have been deployed on the MMT
system compared with others of the same bit rate modulation formats.
The MMT 40 Gb/s post compensation system has 1.4 dB
enhancements to the 40 Gb/s 4-Arysystem and less than 3.9 dB
penalty compared to the 40 Gb/s OOK-RZsystem. However, the
optimized Pre-Post asymmetric compensation has an enhancement of
4.6 dB compared to the Post compensation MMT configuration for a
30% pre compensation dispersion.
Abstract: Hybrid photovoltaic thermal (PV/T) solar system comprises a solar collector which is disposed on photovoltaic solar cells. The disadvantage of a conventional photovoltaic cell is that its performance decreases as the temperature increases. Indeed, part of the solar radiation is converted into electricity and is dissipated as heat, increasing the temperature of the photovoltaic cell with respect to the ambient temperature. The objective of this work is to study experimentally and implement a hybrid prototype to evaluate electrical and thermal performance. In this paper, an experimental study of two new configurations of hybrid collectors is exposed. The results are given and interpreted. The two configurations of absorber studied are a new combination with tubes and galvanized tank, the other is a tubes and sheet.
Abstract: one of the significant factors for improving the
accuracy of Land Surface Temperature (LST) retrieval is the correct
understanding of the directional anisotropy for thermal radiance. In
this paper, the multiple scattering effect between heterogeneous
non-isothermal surfaces is described rigorously according to the
concept of configuration factor, based on which a directional thermal
radiance model is built, and the directional radiant character for urban
canopy is analyzed. The model is applied to a simple urban canopy
with row structure to simulate the change of Directional Brightness
Temperature (DBT). The results show that the DBT is aggrandized
because of the multiple scattering effects, whereas the change range of
DBT is smoothed. The temperature difference, spatial distribution,
emissivity of the components can all lead to the change of DBT. The
“hot spot" phenomenon occurs when the proportion of high
temperature component in the vision field came to a head. On the other
hand, the “cool spot" phenomena occur when low temperature
proportion came to the head. The “spot" effect disappears only when
the proportion of every component keeps invariability. The model
built in this paper can be used for the study of directional effect on
emissivity, the LST retrieval over urban areas and the adjacency effect
of thermal remote sensing pixels.
Abstract: Three-dimensional geometric models have been used
to present architectural and engineering works, showing their final
configuration. When the clarification of a detail or the constitution of
a construction step in needed, these models are not appropriate. They
do not allow the observation of the construction progress of a
building. Models that could present dynamically changes of the
building geometry are a good support to the elaboration of projects.
Techniques of geometric modeling and virtual reality were used to
obtain models that could visually simulate the construction activity.
The applications explain the construction work of a cavity wall and a
bridge. These models allow the visualization of the physical
progression of the work following a planned construction sequence,
the observation of details of the form of every component of the
works and support the study of the type and method of operation of
the equipment applied in the construction. These models presented
distinct advantage as educational aids in first-degree courses in Civil
Engineering. The use of Virtual Reality techniques in the
development of educational applications brings new perspectives to
the teaching of subjects related to the field of civil construction.
Abstract: In recent years, new product development became more and more competitive and globalized, and the designing phase is critical for the product success. The concept of modularity can provide the necessary foundation for organizations to design products that can respond rapidly to market needs. The paper describes data structures and algorithms of intelligent Web-based system for modular design taking into account modules compatibility relationship and given design requirements. The system intelligence is realized by developed algorithms for choice of modules reflecting all system restrictions and requirements. The proposed data structure and algorithms are illustrated by case study of personal computer configuration. The applicability of the proposed approach is tested through a prototype of Web-based system.