Abstract: To tackle the air pollution issues, Plug-in Hybrid
Electric Vehicles (PHEVs) are proposed as an appropriate solution.
Charging a large amount of PHEV batteries, if not controlled, would
have negative impacts on the distribution system. The control process
of charging of these vehicles can be centralized in parking lots that
may provide a chance for better coordination than the individual
charging in houses. In this paper, an optimization-based approach is
proposed to determine the optimum PHEV parking capacities in
candidate nodes of the distribution system. In so doing, a profile for
charging and discharging of PHEVs is developed in order to flatten
the network load profile. Then, this profile is used in solving an
optimization problem to minimize the distribution system losses. The
outputs of the proposed method are the proper place for PHEV
parking lots and optimum capacity for each parking. The application
of the proposed method on the IEEE-34 node test feeder verifies the
effectiveness of the method.
Abstract: The synthesis of CuFe2O4 spinel powders by an
optimized combustion-like process followed by calcination is
described herein. The samples were characterized using X-ray
diffraction (XRD), differential thermal analysis (TG/DTA), scanning
electron microscopy (SEM), dilatometry and 4-probe DC methods.
Different glycine to nitrate (G/N) ratios of 1 (fuel-deficient), 1.48
(stoichiometric) and 2 (fuel-rich) were employed. Calcining the asprepared
powders at 800 and 1000°C for 5 hours showed that the G/N
ratio of 2 results in the formation of the desired copper spinel single
phase at both calcination temperatures. For G/N=1, formation of
CuFe2O4 takes place in three steps. First, iron and copper nitrates
decompose to iron oxide and pure copper. Then, copper transforms to
copper oxide and finally, copper and iron oxides react with each other
to form a copper ferrite spinel phase. The electrical conductivity and
the coefficient of thermal expansion of the sintered pelletized
samples were 2 S.cm-1 (800°C) and 11×10-6 °C-1 (25-800°C),
respectively.
Abstract: Sustainability is a very important and heavily
discussed subject, expanding through tourism as well. The study
proposition was to collect data and present it to the competent bodies
so they can mold their public policies to improve the conditions of
the site. It was hypothesized that the lack of data is currently
affecting the quality of life and the sustainable development of the
site and the tourism. The research was held in Mateiros, a city in the
state of Tocantins (TO)/Brasil near Palmas, its capital city. Because
of the concentration of tourists during the high season and several
tourist attractions being around, the research took place in Mateiros.
The methodological procedure had a script of theoretical construction
and investigation of the deductive scientific method parameters
through a case study in the Jalapão/TO/Brazil region, using it as a
tool for a questionnaire given to the competent bodies in an interview
system with the UN sustainability indexes as a base. In the three
sustainable development scope: environmental, social and economic,
the results indicated that the data presented by the interviewed were
scarce or nonexistent. It shows that more research is necessary,
providing the tools for the ones responsible to propose action plans to
improve the site, strengthening the tourism and making it even more
sustainable.
Abstract: Plants can contain a wide variety of substances with
antioxidative properties which are associated with important health
benefits. These positive health effects are of great importance at a
time when the environment is laden with many toxic substances. Five
selected herbal plants namely, Mimosa pudica, Phyllanthus niruri,
Ceiba pentandra, Eleusine polydactyla and Trema amboinensi, were
chosen for the experiment to investigate their total phenolics content
and antioxidant activities using ABTS radical cation decolorization
power, and ferric reducing antioxidant power. The total phenolic
content of each herbal plants ranges from 0.84 to 42.59 mg gallic acid
equivalent/g. The antioxidant activity in the ABTS radical cation
decolorization power varies from 0.005 to 0.362 mg trolox
equivalent/g and the FRAP ranges from 0.30 to 28.42 mg gallic acid
equivalent/g. Among the five medicinal plants, Mimosa pudica has
been an excellent performer in terms of the 3 parameters measured; it
is followed by Phyllanthus niruri. The 5 herbal plants do not have
equivalent antioxidant power. The relative high values for M. pudica
and P. niruri supports the medicinal value of both plants. The total
phenolics, ABTS and FRAP correlate strongly with one another.
Abstract: Several embryonic cellular mechanism including cell
cycle, growth and apoptosis are regulated by phosphatidylinositol-3-
kinase (PI3K)/Akt signaling pathway. The goal of present study is to
determine the effects of annatto (Bixa orellana)-derived δ-tocotrienol
(δ-TCT) on the regulations of PI3K/Akt genes in murine morula.
Twenty four 6-8 week old (23-25g) female balb/c mice were
randomly divided into four groups (G1-G4; n=6). Those groups were
subjected to the following treatments for 7 consecutive days: G1
(control) received tocopherol stripped corn oil, G2 was given 60
mg/kg/day of δ-TCT mixture (contains 90% delta & 10% gamma
isomers), G3 was given 60 mg/kg/day of pure δ-TCT (>98% purity)
and G4 received 60 mg/kg/day α-TOC. On Day 8, females were
superovulated with 5 IU Pregnant Mare’s Serum Gonadotropin
(PMSG) for 48 hours followed with 5 IU human Chorionic
Gonadotropin (hCG) before mated with males at the ratio of 1:1.
Females were sacrificed by cervical dislocation for embryo collection
48 hours post-coitum. About fifty morulas from each group were
used in the gene expression analyses using Affymetrix QuantiGene
Plex 2.0 Assay. Present data showed a significant increase (p
Abstract: A Rice Sheller is used for obtaining polished white
rice from paddy. There are about 3000 Rice Shellers in Punjab and
50000 in India. During the process of shelling lot of dust is emitted
from different unit operations like paddy silo, paddy shaker, bucket
elevators, huskers, paddy separator etc. These dust emissions have
adverse effect on the health of the workers and the wear and tear of
the shelling machinery is fast. All the dust emissions spewing out of
these unit operations of a rice Sheller were contained by providing
suitable hoods and enclosures while ensuring their workability. These
were sucked by providing an induced draft fan followed by a high
efficiency cyclone separator that has got an overall dust collection
efficiency of more than 90%. This cyclone separator replaced two
cyclone separators and a filter bag house, which the Rice Sheller was
already having. The dust concentration in the stack after the
installation of cyclone separator is well within the stipulated
standards. Besides controlling pollution, there is improvement in the
quality of products like bran and the life of shelling machinery has
enhanced. The payback period of this technology is less than four
shelling months.
Abstract: A robust sequential nonparametric method is proposed
for adaptation to background noise parameters for real-time. The
distribution of background noise was modelled like to Huber
contamination mixture. The method is designed to operate as an
adaptation-unit, which is included inside a detection subsystem of an
integrated multichannel monitoring system. The proposed method
guarantees the given size of a nonasymptotic confidence set for noise
parameters. Properties of the suggested method are rigorously
proved. The proposed algorithm has been successfully tested in real
conditions of a functioning C-OTDR monitoring system, which was
designed to monitor railways.
Abstract: The MEMS pressure sensor has been introduced and
presented in this paper. The types of pressure sensor and its theory of
operation are also included. The latest MEMS technology, the
fabrication processes of pressure sensor are explored and discussed.
Besides, various device applications of pressure sensor such as tire
pressure-monitoring system, diesel particulate filter and others are
explained. Due to further miniaturization of the device nowadays, the
pressure sensor with nanotechnology (NEMS) is also reviewed. The
NEMS pressure sensor is expected to have better performance as well
as lower in its cost. It has gained an excellent popularity in many
applications.
Abstract: Live video streaming is one of the most widely used
service among end users, yet it is a big challenge for the network
operators in terms of quality. The only way to provide excellent
Quality of Experience (QoE) to the end users is continuous
monitoring of live video streaming. For this purpose, there are several
objective algorithms available that monitor the quality of the video in
a live stream. Subjective tests play a very important role in fine
tuning the results of objective algorithms. As human perception is
considered to be the most reliable source for assessing the quality of a
video stream subjective tests are conducted in order to develop more
reliable objective algorithms. Temporal impairments in a live video
stream can have a negative impact on the end users. In this paper we
have conducted subjective evaluation tests on a set of video
sequences containing temporal impairment known as frame freezing.
Frame Freezing is considered as a transmission error as well as a
hardware error which can result in loss of video frames on the
reception side of a transmission system. In our subjective tests, we
have performed tests on videos that contain a single freezing event
and also for videos that contain multiple freezing events. We have
recorded our subjective test results for all the videos in order to give a
comparison on the available No Reference (NR) objective
algorithms. Finally, we have shown the performance of no reference
algorithms used for objective evaluation of videos and suggested the
algorithm that works better. The outcome of this study shows the
importance of QoE and its effect on human perception. The results
for the subjective evaluation can serve the purpose for validating
objective algorithms.
Abstract: This paper shows the general perceptions of Spanish
university stakeholders in relation to the university’s annual reports
and the adequacy and potential of intellectual capital reporting. To
this end, a questionnaire was designed and sent to every member of
the Social Councils of Spanish public universities. It was thought that
these participants would provide a good example of the attitude of
university stakeholders since they represent the different social
groups connected with universities. From the results of this study we
are in the position of confirming the need for universities to offer
information on intellectual capital in their accounting information
model.
Abstract: Multiple User Interference (MUI) considers the
primary problem in Optical Code-Division Multiple Access
(OCDMA), which resulting from the overlapping among the users. In
this article we aim to mitigate this problem by studying an
interference cancellation scheme called successive interference
cancellation (SIC) scheme. This scheme will be tested on two
different detection schemes, spectral amplitude coding (SAC) and
direct detection systems (DS), using partial modified prime (PMP) as
the signature codes. It was found that SIC scheme based on both SAC
and DS methods had a potential to suppress the intensity noise, that is
to say it can mitigate MUI noise. Furthermore, SIC/DS scheme
showed much lower bit error rate (BER) performance relative to
SIC/SAC scheme for different magnitude of effective power. Hence,
many more users can be supported by SIC/DS receiver system.
Abstract: This paper presents an approach of on-line control of
the state of technosphere and environment objects based on the
integration of Data Warehouse, OLAP and Expert systems
technologies. It looks at the structure and content of data warehouse
that provides consolidation and storage of monitoring data. There is a
description of OLAP-models that provide a multidimensional
analysis of monitoring data and dynamic analysis of principal
parameters of controlled objects. The authors suggest some criteria of
emergency risk assessment using expert knowledge about danger
levels. It is demonstrated now some of the proposed solutions could
be adopted in territorial decision making support systems.
Operational control allows authorities to detect threat, prevent natural
and anthropogenic emergencies and ensure a comprehensive safety of
territory.
Abstract: Significant attention has recently been paid to the
cross-cultural negotiations due to the growth of international
businesses. Despite the substantial body of literature examining the
influence of National Culture (NC) dimensions on negotiations, there
is a lack of studies comparing the influence of NC in Latin America
with a Western European countries, In particular, an extensive review
of the literature revealed that a contribution to knowledge would be
derived from the comparison of the influence of NC dimensions on
negotiations in UK and Venezuela. The primary data was collected
through qualitative interviews, to obtain an insight about the
perceptions and beliefs of Venezuelan and British business managers
about their negotiating styles. The findings of this study indicated
that NC has a great influence on the negotiating styles. In particular,
Venezuelan and British managers demonstrated to have opposed
negotiating styles, affecting the way they communicate, approach
people and their willingness to take risks.
Abstract: This research aims to identify traditional Mon cuisines
as well as gather and classify traditional cuisines of Mon
communities in Bangkok. The studying of this research is used by
methodology of the quantitative research. Using the questionnaire as
the method in collecting information from sampling totally amount of
450 persons analyzed via frequency, percentage and mean value. The
results showed that a variety of traditional Mon cuisines of Bangkok
could split into 6 categories of meat diet with 54 items and 6
categories of desserts with 19 items.
Abstract: This contribution presents a friction estimator for
industrial purposes which identifies Coulomb friction in a steering
system. The estimator only needs a few, usually known, steering
system parameters. Friction occurs on almost every mechanical
system and has a negative influence on high-precision position
control. This is demonstrated on a steering angle controller for highly
automated driving. In this steering system the friction induces limit
cycles which cause oscillating vehicle movement when the vehicle
follows a given reference trajectory. When compensating the friction
with the introduced estimator, limit cycles can be suppressed. This
is demonstrated by measurements in a series vehicle.
Abstract: The purpose of this study is to evaluate the English
version and a Malay translation of the 21-item Learner Awareness
Questionnaire for its application to assess student learning in higher
education. The Learner Awareness Questionnaire, originally written
in English, is a quantitative measure of how and why students learn.
The questionnaire gives an indication of the process and motives to
learn using four scales: survival, establishing stability, approval and
loving to learn. Data in the present study came from 680 university
students enrolled in various programmes in Malaysia. The Malay
version of the questionnaire supported a similar four factor structure
and internal consistency to the English version. The four factors of
the Malay version also showed moderate to strong correlations with
those of the English versions. The results suggest that the Malay
version of the questionnaire is similar to the English version.
However, further refinement to the questions is needed to strengthen
the correlations between the two questionnaires.
Abstract: DNA Barcode provides good sources of needed
information to classify living species. The classification problem has
to be supported with reliable methods and algorithms. To analyze
species regions or entire genomes, it becomes necessary to use the
similarity sequence methods. A large set of sequences can be
simultaneously compared using Multiple Sequence Alignment which
is known to be NP-complete. However, all the used methods are still
computationally very expensive and require significant computational
infrastructure. Our goal is to build predictive models that are highly
accurate and interpretable. In fact, our method permits to avoid the
complex problem of form and structure in different classes of
organisms. The empirical data and their classification performances
are compared with other methods. Evenly, in this study, we present
our system which is consisted of three phases. The first one, is called
transformation, is composed of three sub steps; Electron-Ion
Interaction Pseudopotential (EIIP) for the codification of DNA
Barcodes, Fourier Transform and Power Spectrum Signal Processing.
Moreover, the second phase step is an approximation; it is
empowered by the use of Multi Library Wavelet Neural Networks
(MLWNN). Finally, the third one, is called the classification of DNA
Barcodes, is realized by applying the algorithm of hierarchical
classification.
Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.
Abstract: Distillery spentwash contains high chemical oxygen
demand (COD), biological oxygen demand (BOD), color, total
dissolved solids (TDS) and other contaminants even after biological
treatment. The effluent can’t be discharged as such in the surface
water bodies or land without further treatment. Reverse osmosis (RO)
treatment plants have been installed in many of the distilleries at
tertiary level in many of the distilleries in India, but are not properly
working due to fouling problem which is caused by the presence of
high concentration of organic matter and other contaminants in
biologically treated spentwash. In order to make the membrane
treatment a proven and reliable technology, proper pre-treatment is
mandatory. In the present study, ultra-filtration (UF) for pretreatment
of RO at tertiary stage has been performed. Operating
parameters namely initial pH (pHo: 2–10), trans-membrane pressure
(TMP: 4-20 bars) and temperature (T: 15-43°C) were used for
conducting experiments with UF system. Experiments were
optimized at different operating parameters in terms of COD, color,
TDS and TOC removal by using response surface methodology
(RSM) with central composite design. The results showed that
removal of COD, color and TDS was 62%, 93.5% and 75.5%
respectively, with UF, at optimized conditions with increased
permeate flux from 17.5 l/m2/h (RO) to 38 l/m2/h (UF-RO). The
performance of the RO system was greatly improved both in term of
pollutant removal as well as water recovery.
Abstract: The main parameters affecting the workability are the
water content, particle size, and the total surface of the grains, as long
as the mixing water begins by wetting the surface of the grains and
then fills the voids between the grains to form entrapped water, the
quantity of water remaining is called free water. The aim of this study is to undertake a fractal approach through
the relationship between the concrete formulation parameters and
workability. To develop this approach a series of concrete taken from
the literature was investigated by varying formulation parameters
such as G/S, the quantity of cement C and the quantity of water W. We also call another model as the model of water layer thickness
and model of paste layer thickness to judge their relevance, hence the
following results: the relevance of the water layer thickness model is
considered as a relevant when there is a variation in the water
quantity. The model of the paste layer thickness is only applicable if
we considered that the paste is made with the grain value Dmax =
2.85: value from which we see a stability of the model.