Abstract: In this paper the fatigue crack initiation location of double shear lap joints, treated by interference fit and bolt clamping, have been investigated both experimentally and numerically. To do so, using the fracture section of available fatigue tested specimens of interference fitted and torque tightened Aluminum 2024-T3 plates, the crack initiation location was determined. The stress distribution attained from the finite element analysis was used to help explain the results observed in the experimental tests. The results showed that the fatigue crack initiation location changes from top and mid plane at the hole edge to somewhere far from the hole edge (stress concentration region) in different combination of clamping force, interference fit size and applied cyclic load ranges. It is worth mentioning that the fatigue crack initiation location affects the fatigue life of the specimens too.
Abstract: In this manuscript, a wavelet-based blind
watermarking scheme has been proposed as a means to provide
security to authenticity of a fingerprint. The information used for
identification or verification of a fingerprint mainly lies in its
minutiae. By robust watermarking of the minutiae in the fingerprint
image itself, the useful information can be extracted accurately even
if the fingerprint is severely degraded. The minutiae are converted in
a binary watermark and embedding these watermarks in the detail
regions increases the robustness of watermarking, at little to no
additional impact on image quality. It has been experimentally shown
that when the minutiae is embedded into wavelet detail coefficients
of a fingerprint image in spread spectrum fashion using a
pseudorandom sequence, the robustness is observed to have a
proportional response while perceptual invisibility has an inversely
proportional response to amplification factor “K". The DWT-based
technique has been found to be very robust against noises,
geometrical distortions filtering and JPEG compression attacks and is
also found to give remarkably better performance than DCT-based
technique in terms of correlation coefficient and number of erroneous
minutiae.
Abstract: A method to determine experimentally the melting
rate, rm, and the heat transfer coefficients, αv (W/(m3K)), at
convective melting in a fixed bed of particles under adiabatic regime
is established in this paper. The method lies in the determining of the
melting rate by measuring the fixed bed height in time. Experimental
values of rm, α and α v were determined using cylindrical particles of
ice (d = 6.8 mm, h = 5.5 mm) and, as a melting agent, aqueous NaCl
solution with a temperature of 283 K at different values of the liquid
flow rate (11.63·10-6, 28.83·10-6, 38.83·10-6 m3/s).
Our experimental results were compared with those existing in
literature being noticed a good agreement for Re values higher than
50.
Abstract: A Positron Emission Tomography (PET) is a radioisotope imaging technique that illustrates the organs and the metabolisms of the human body. This technique is based on the simultaneous detection of 511 keV annihilation photons, annihilated as a result of electrons annihilating positrons that radiate from positron-emitting radioisotopes that enter biological active molecules in the body. This study was conducted on ten patients in an effort to conduct patient-related experimental studies. Dosage monitoring for the bladder, which was the organ that received the highest dose during PET applications, was conducted for 24 hours. Assessment based on measuring urination activities after injecting patients was also a part of this study. The MIRD method was used to conduct dosage calculations for results obtained from experimental studies. Results obtained experimentally and theoretically were assessed comparatively.
Abstract: MicroRNAs (miRNAs) are a class of non-coding
RNAs that hybridize to mRNAs and induce either translation
repression or mRNA cleavage. Recently, it has been reported that
miRNAs could possibly play an important role in human diseases. By
integrating miRNA target genes, cancer genes, miRNA and mRNA
expression profiles information, a database is developed to link
miRNAs to cancer target genes. The database provides experimentally
verified human miRNA target genes information, including oncogenes
and tumor suppressor genes. In addition, fragile sites information for
miRNAs, and the strength of the correlation of miRNA and its target
mRNA expression level for nine tissue types are computed, which
serve as an indicator for suggesting miRNAs could play a role in
human cancer. The database is freely accessible at
http://ppi.bioinfo.asia.edu.tw/mirna_target/index.html.
Abstract: This study experimentally and numerically investigates
motor cooling performance. The motor consists of a centrifugal fan,
two axial fans, a shaft, a stator, a rotor and a heat exchanger with 637
cooling tubes. The pressure rise-flow rate (P-Q) performance curves of
the cooling fans at 1800 rpm are tested using a test apparatus
complying with the Chinese National Standard (CNS) 2726.
Compared with the experimental measurements, the numerical
analysis results show that the P-Q performance curves of the axial fan
and centrifugal fan can be estimated within about 2% and 6%,
respectively. By using the simplified model, setting up the heat
exchanger and stator as porous media, the flow field in the motor is
calculated. By using the results of the flow field near the rotor and
stator, and subjecting the heat generation rate as a boundary condition,
the temperature distributions of the stator and rotor are also calculated.
The simulation results show that the calculated temperature of the
stator winding near the axial fans is lower by about 5% than the
measured value, and the calculated temperature of the stator core
located at the center of the stator is about 1% higher than the measured
value. Besides, discussion is made to improve the motor cooling
performance.
Abstract: Shear-layer instabilities of a pulsed stack-issued
transverse jet were studied experimentally in a wind tunnel. Jet
pulsations were induced by means of acoustic excitation. Streak
pictures of the smoke-flow patterns illuminated by the laser-light sheet
in the median plane were recorded with a high-speed digital camera.
Instantaneous velocities of the shear-layer instabilities in the flow were
digitized by a hot-wire anemometer. By analyzing the streak pictures
of the smoke-flow visualization, three characteristic flow modes,
synchronized flapping jet, transition, and synchronized shear-layer
vortices, are identified in the shear layer of the pulsed stack-issued
transverse jet at various excitation Strouhal numbers. The shear-layer
instabilities of the pulsed stack-issued transverse jet are synchronized
by acoustic excitation except for transition mode. In transition flow
mode, the shear-layer vortices would exhibit a frequency that would be
twice as great as the acoustic excitation frequency.
Abstract: Compacted clay liners (CCLs) are the main materials
used in waste disposal landfills due to their low permeability. In this
study, the effect on the shear resistant of clays with inorganic salt
solutions as permeate fluid was experimentally investigated. For this
purpose, NaCl inorganic salt solution at concentrations of 2, 5, 10%
and deionized water were used. Laboratory direct shear and Vane
shear tests were conducted on three compacted clays with low,
medium and high plasticity. Results indicated that the solutions type
and its concentration affect the shear properties of the mixture. In the
light of this study, the influence magnitude of these inorganic salts in
varies concentrations in different clays were determined and more
suitable compacted clay with the compare of plasticity were found.
Abstract: Solidification cracking and hydrogen cracking are some defects generated in the fusion welding of ultrahigh carbon steels. However, friction stir welding (FSW) of such steels, being a solid-state technique, has been demonstrated to alleviate such problems encountered in traditional welding. FSW include different process parameters that must be carefully defined prior processing. These parameters included but not restricted to: tool feed, tool RPM, tool geometry, tool tilt angle. These parameters form a key factor behind avoiding warm holes and voids behind the tool and in achieving a defect-free weld. More importantly, these parameters directly affect the microstructure of the weld and hence the final mechanical properties of weld. For that, 3D finite element (FE) thermo-mechanical model was developed using DEFORM 3D to simulate FSW of carbon steel. At points of interest in the joint, tracking is done for history of critical state variables such as temperature, stresses, and strain rates. Typical results found include the ability to simulate different weld zones. Simulations predictions were successfully compared to experimental FSW tests. It is believed that such a numerical model can be used to optimize FSW processing parameters to favor desirable defect free weld with better mechanical properties.
Abstract: This paper deals with a novel technique for the
fabrication of Spiral grooves in a dynamic thrust bearing. The main
scheme proposed in this paper is to fabricate the microgrooves using
desktop forming system. This process has advantages compared to the
conventional electro-chemical machining in the viewpoint of a higher
productivity. For this reason, a new testing apparatus is designed and
built for press forming microgrooves on a surface of the thrust bearing.
The material used in this study is sintered Cu-Fe alloy. The effects of
the forming load on the performance of micro press forming are
experimentally investigated. From the experimental results, formed
depths are closed to the target ones with increasing the forming load.
Abstract: Sedimentation in reservoirs and the corresponding
loss of storage capacity is one of the most serious problems in dam
engineering. Pressurized flushing, a way to remove sediments from the reservoir, is flushing under a pressurized flow condition and
nearly constant water level. Pressurized flushing has only local
effects around the outlet. Sediment in the vicinity of the outlet openings is scoured and a funnel shaped crater is created. In this study, the temporal development of flushing cone under various
hydraulic conditions was studied experimentally. Time variations of
parameters such as maximum length and width of flushing and also
depth of scouring cone was measured. Results indicated that an
increase in flow velocity (and consequently in Froude number)
established new hydraulically conditions for flushing mechanism and
so a sudden growth was observed in the amount of sediment released
and also scouring dimenssions. In addition, a set of nondimensional
relationships were identified for temporal variations of flushing scour
dimenssions, which can eventuallt be used to estimate the development of flushing cone.
Abstract: In this work, we experimentally study heat transfer
from exhaust particulate air of detergent spray drying tower to water
by using coiled tube heat exchanger. Water flows in the coiled
tubes, where air loaded with detergent particles of 43 micrometers
in diameter flows within the shell. Four coiled tubes with different
coil pitches are used in a counter-current flow configuration. We
investigate heat transfer coefficients of inside and outside the heat
transfer surfaces through 400 experiments. The correlations between
Nusselt number and Reynolds number, Prandtl number, mass flow
rate of particulates to mass flow rate of air ratio and coiled tube
pitch parameter are proposed. The correlations procured can be used
to predicted heat transfer between tube and shell of the heat
exchanger.
Abstract: In this paper, experimental testing and numerical analysis were used to investigate the effect of tube thickness on the face bending for concrete filled hollow sections connected to other structural members using Extended Hollobolts. Six samples were tested experimentally by applying pull-out load on the bolts. These samples were designed to fail by column face bending. The main variable in all tests is the column face thickness. Finite element analyses were also performed using ABAQUS 6.11 to extend the experimental results and to quantify the effect of column face thickness. Results show that, the column face thickness has a clear impact on the connection strength and stiffness. However, the amount of improvement in the connection stiffness by changing the column face thickness from 5mm to 6.3mm seems to be higher than that when increasing it from 6.3mm to 8mm. The displacement at which the bolts start pulling-out from their holes increased with the use of thinner column face due to the high flexibility of the section. At the ultimate strength, the yielding of the column face propagated to the column corner and there was no yielding in its walls. After the ultimate resistance is reached, the propagation of the yielding was mainly in the column face with a miner yielding in the walls.
Abstract: An application framework provides a reusable design
and implementation for a family of software systems. If the
framework contains defects, the defects will be passed on to the
applications developed from the framework. Framework defects are
hard to discover at the time the framework is instantiated. Therefore,
it is important to remove all defects before instantiating the
framework. In this paper, two measures for the adequacy of an
object-oriented system-based testing technique are introduced. The
measures assess the usefulness and uniqueness of the testing
technique. The two measures are applied to experimentally compare
the adequacy of two testing techniques introduced to test objectoriented
frameworks at the system level. The two considered testing
techniques are the New Framework Test Approach and Testing
Frameworks Through Hooks (TFTH). The techniques are also
compared analytically in terms of their coverage power of objectoriented
aspects. The comparison study results show that the TFTH
technique is better than the New Framework Test Approach in terms
of usefulness degree, uniqueness degree, and coverage power.
Abstract: Controlled release urea has become popular in agricultural industry as it helps to solve environmental issues and increase crop yield. Recently biomass was identified to replace the polymer used as a coating material in the conventional coated urea. In this paper spreading and contact angle of biomass droplet (lignin, cellulose and clay) on urea surface are investigated experimentally. There were two tests were conducted, sessile drop for contact angle measurement and pendant drop for contact angle measurement. A different concentration of biomass droplet was released from 30 mm above a substrate. Glass was used as a controlled substrate. Images were recorded as soon as the droplet impacted onto the urea before completely adsorb into the urea. Digitized droplets were then used to identify the droplet-s surface tension and contact angle. There is large difference observed between the low surface tension and high surface tension liquids, where the wetting and spreading diameter is higher for lower surface tension. From the contact angle results, the data showed that the biomass coating films were possible as wetting liquid (θ < 90º). Contact angle of biomass coating material gives good indication for the wettablity of a liquid on urea surface.
Abstract: A Comparison and evaluation of the different
condition monitoring (CM) techniques was applied experimentally
on RC e.g. Dynamic cylinder pressure and crankshaft Instantaneous
Angular Speed (IAS), for the detection and diagnosis of valve faults
in a two - stage reciprocating compressor for a programme of
condition monitoring which can successfully detect and diagnose a
fault in machine. Leakage in the valve plate was introduced
experimentally into a two-stage reciprocating compressor. The effect
of the faults on compressor performance was monitored and the
differences with the normal, healthy performance noted as a fault
signature been used for the detection and diagnosis of faults.
The paper concludes with what is considered to be a unique
approach to condition monitoring. First, each of the two most useful
techniques is used to produce a Truth Table which details the
circumstances in which each method can be used to detect and
diagnose a fault. The two Truth Tables are then combined into a
single Decision Table to provide a unique and reliable method of
detection and diagnosis of each of the individual faults introduced
into the compressor. This gives accurate diagnosis of compressor
faults.
Abstract: In this study, the effect of nanofluids on the pool film
boiling was experimentally investigated at saturated condition under
atmospheric pressure. For this purpose, four different water-based
nanofluids (Al2O3, SiO2, TiO2 and CuO) with 0.1% particle volume
fraction were prepared. To investigate the boiling heat transfer, a
cylindrical rod with high temperature was used. The rod heated up to
high temperatures was immersed into nanofluids. The center
temperature of rod during the cooling process was recorded by using
a K-type thermocouple. The quenching curves showed that the pool
boiling heat transfer was strongly dependent on the nanoparticle
materials. During the repetitive quenching tests, the cooling time
decreased and thus, the film boiling vanished. Consequently, the
primary reason of this was the change of the surface characteristics
due to the nanoparticles deposition on the rod-s surface.
Abstract: Feeder is one of the airships of the Multibody Advanced Airship for Transport (MAAT) system, under development within the EU FP7 project. MAAT is based on a modular concept composed of two different parts that have the possibility to join; respectively they are the so-called Cruiser and Feeder, designed on the lighter than air principle. Feeder, also named ATEN (Airship Transport Elevator Network), is the smaller one which joins the bigger one, Cruiser, also named PTAH (Photovoltaic modular Transport Airship for High altitude),envisaged to happen at 15km altitude. During the MAAT design phase, the aerodynamic studies of the both airships and their interactions are analyzed. The objective of these studies is to understand the aerodynamic behavior of all the preselected configurations, as an important element in the overall MAAT system design. The most of these configurations are only simulated by CFD, while the most feasible one is experimentally analyzed in order to validate and thrust the CFD predictions. This paper presents the numerical and experimental investigation of the Feeder “conical like" shape configuration. The experiments are focused on the aerodynamic force coefficients and the pressure distribution over the Feeder outer surface, while the numerical simulation cover also the analysis of the velocity and pressure distribution. Finally, the wind tunnel experiment is compared with its CFD model in order to validate such specific simulations with respective experiments and to better understand the difference between the wind tunnel and in-flight circumstances.
Abstract: Behavior of turbulent jet is relying on jet parameters,
environmental and geometric parameters. In this research, it has
attempt to Study effect of jet parameters of internal angle on
maximum effective length and velocity on centerline from nozzle
experimentally. Toward this end, four internal angles 30, 45, 60 and
90-degree are considered for this study in a flume with 600cm as
long, 100cm as high and 150cm in width. Various discharges were
used to evaluate effective length for a wide range of densimetric
Froude numbers F0, from 17.9 to 39.4 that is defined at the nozzle. As
a result, It is revealed that both velocity on centerline and effective
length decreases when nozzle angle decreased from 90° to 30°. The
results show that, for all range of Fr0 the Um/U0 ratio for nozzle with
α=90° on centerline increases 20% - 27% than nozzle with α=30° that
has lowest velocity on centerline than other nozzle.
Abstract: Regenerative Thermal Oxidizer (RTO) is one of the
best solutions for removal of Volatile Organic Compounds (VOC)
from industrial processes. In the RTO, VOC in a raw gas are usually
decomposed at 950-1300 K and the combustion heat of VOC is
recovered by regenerative heat exchangers charged with ceramic
honeycombs. The optimization of the treatment of VOC leads to the
reduction of fuel addition to VOC decomposition, the minimization of
CO2 emission and operating cost as well.
In the present work, the thermal efficiency of the RTO was
investigated experimentally in a pilot-scale RTO unit using toluene as
a typical representative of VOC. As a result, it was recognized that the
radiative heat transfer was dominant in the preheating process of a raw
gas when the gas flow rate was relatively low. Further, it was found
that a minimum heat exchanger volume to achieve self combustion of
toluene without additional heating of the RTO by fuel combustion was
dependent on both the flow rate of a raw gas and the concentration of
toluene. The thermal efficiency calculated from fuel consumption and
the decomposed toluene ratio, was found to have a maximum value of
0.95 at a raw gas mass flow rate of 1810 kg·h-1 and honeycombs height
of 1.5m.