Abstract: This paper proposes a new methodology for the
optimal allocation and sizing of Embedded Generation (EG)
employing Real Coded Genetic Algorithm (RCGA) to minimize the
total power losses and to improve voltage profiles in the radial
distribution networks. RCGA is a method that uses continuous
floating numbers as representation which is different from
conventional binary numbers. The RCGA is used as solution tool,
which can determine the optimal location and size of EG in radial
system simultaneously. This method is developed in MATLAB. The
effect of EG units- installation and their sizing to the distribution
networks are demonstrated using 24 bus system.
Abstract: In this paper a new embedded Singly Diagonally
Implicit Runge-Kutta Nystrom fourth order in fifth order method for
solving special second order initial value problems is derived. A
standard set of test problems are tested upon and comparisons on the
numerical results are made when the same set of test problems are
reduced to first order systems and solved using the existing
embedded diagonally implicit Runge-Kutta method. The results
suggests the superiority of the new method.
Abstract: Scale Time Offset Robust Modulation (STORM) [1]–
[3] is a high bandwidth waveform design that adds time-scale
to embedded reference modulations using only time-delay [4]. In
an environment where each user has a specific delay and scale,
identification of the user with the highest signal power and that
user-s phase is facilitated by the STORM processor. Both of these
parameters are required in an efficient multiuser detection algorithm.
In this paper, the STORM modulation approach is evaluated with
a direct sequence spread quadrature phase shift keying (DS-QPSK)
system. A misconception of the STORM time scale modulation is that
a fine temporal resolution is required at the receiver. STORM will
be applied to a QPSK code division multiaccess (CDMA) system
by modifying the spreading codes. Specifically, the in-phase code
will use a typical spreading code, and the quadrature code will
use a time-delayed and time-scaled version of the in-phase code.
Subsequently, the same temporal resolution in the receiver is required
before and after the application of STORM. In this paper, the bit error
performance of STORM in a synchronous CDMA system is evaluated
and compared to theory, and the bit error performance of STORM
incorporated in a single user WCDMA downlink is presented to
demonstrate the applicability of STORM in a modern communication
system.
Abstract: In this paper, a novel scheme is proposed for Ownership Identification and Color Image Authentication by deploying Cryptography & Digital Watermarking. The color image is first transformed from RGB to YST color space exclusively designed for watermarking. Followed by color space transformation, each channel is divided into 4×4 non-overlapping blocks with selection of central 2×2 sub-blocks. Depending upon the channel selected two to three LSBs of each central 2×2 sub-block are set to zero to hold the ownership, authentication and recovery information. The size & position of sub-block is important for correct localization, enhanced security & fast computation. As YS ÔèÑ T so it is suitable to embed the recovery information apart from the ownership and authentication information, therefore 4×4 block of T channel along with ownership information is then deployed by SHA160 to compute the content based hash that is unique and invulnerable to birthday attack or hash collision instead of using MD5 that may raise the condition i.e. H(m)=H(m'). For recovery, intensity mean of 4x4 block of each channel is computed and encoded upto eight bits. For watermark embedding, key based mapping of blocks is performed using 2DTorus Automorphism. Our scheme is oblivious, generates highly imperceptible images with correct localization of tampering within reasonable time and has the ability to recover the original work with probability of near one.
Abstract: Over last two decades, due to hostilities of environment
over the internet the concerns about confidentiality of information
have increased at phenomenal rate. Therefore to safeguard the information
from attacks, number of data/information hiding methods have
evolved mostly in spatial and transformation domain.In spatial domain
data hiding techniques,the information is embedded directly on
the image plane itself. In transform domain data hiding techniques the
image is first changed from spatial domain to some other domain and
then the secret information is embedded so that the secret information
remains more secure from any attack. Information hiding algorithms
in time domain or spatial domain have high capacity and relatively
lower robustness. In contrast, the algorithms in transform domain,
such as DCT, DWT have certain robustness against some multimedia
processing.In this work the authors propose a novel steganographic
method for hiding information in the transform domain of the gray
scale image.The proposed approach works by converting the gray
level image in transform domain using discrete integer wavelet
technique through lifting scheme.This approach performs a 2-D
lifting wavelet decomposition through Haar lifted wavelet of the cover
image and computes the approximation coefficients matrix CA and
detail coefficients matrices CH, CV, and CD.Next step is to apply the
PMM technique in those coefficients to form the stego image. The
aim of this paper is to propose a high-capacity image steganography
technique that uses pixel mapping method in integer wavelet domain
with acceptable levels of imperceptibility and distortion in the cover
image and high level of overall security. This solution is independent
of the nature of the data to be hidden and produces a stego image
with minimum degradation.
Abstract: The psychological and physical trauma associated with the loss of a human limb can severely impact on the quality of life of an amputee rendering even the most basic of tasks very difficult. A prosthetic device can be of great benefit to the amputee in the performance of everyday human tasks. This paper outlines a proposed mechanical design of a 12 degree-of-freedom SMA actuated artificial hand. It is proposed that the SMA wires be embedded intrinsically within the hand structure which will allow for significant flexibility for use either as a prosthetic hand solution, or as part of a complete lower arm prosthetic solution. A modular approach is taken in the design facilitating ease of manufacture and assembly, and more importantly, also allows the end user to easily replace SMA wires in the event of failure. A biomimetric approach has been taken during the design process meaning that the artificial hand should replicate that of a human hand as far as is possible with due regard to functional requirements. The proposed design has been exposed to appropriate loading through the use of finite element analysis (FEA) to ensure that it is structurally sound. Theoretical analysis of the mechanical framework was also carried out to establish the limits of the angular displacement and velocity of the finger tip as well finger tip force generation. A combination of various polymers and Titanium, which are suitably lightweight, are proposed for the manufacture of the design.
Abstract: In this paper, we present a novel, principled approach to resolve the remained problems of substitution technique of audio steganography. Using the proposed genetic algorithm, message bits are embedded into multiple, vague and higher LSB layers, resulting in increased robustness. The robustness specially would be increased against those intentional attacks which try to reveal the hidden message and also some unintentional attacks like noise addition as well.
Abstract: Security has been an important issue and concern in the
smart home systems. Smart home networks consist of a wide range of
wired or wireless devices, there is possibility that illegal access to
some restricted data or devices may happen. Password-based
authentication is widely used to identify authorize users, because this
method is cheap, easy and quite accurate. In this paper, a neural
network is trained to store the passwords instead of using verification
table. This method is useful in solving security problems that
happened in some authentication system. The conventional way to
train the network using Backpropagation (BPN) requires a long
training time. Hence, a faster training algorithm, Resilient
Backpropagation (RPROP) is embedded to the MLPs Neural
Network to accelerate the training process. For the Data Part, 200
sets of UserID and Passwords were created and encoded into binary
as the input. The simulation had been carried out to evaluate the
performance for different number of hidden neurons and combination
of transfer functions. Mean Square Error (MSE), training time and
number of epochs are used to determine the network performance.
From the results obtained, using Tansig and Purelin in hidden and
output layer and 250 hidden neurons gave the better performance. As
a result, a password-based user authentication system for smart home
by using neural network had been developed successfully.
Abstract: Knowledge of an organization does not merely reside
in structured form of information and data; it is also embedded in
unstructured form. The discovery of such knowledge is particularly
difficult as the characteristic is dynamic, scattered, massive and
multiplying at high speed. Conventional methods of managing
unstructured information are considered too resource demanding and
time consuming to cope with the rapid information growth.
In this paper, a Multi-faceted and Automatic Knowledge
Elicitation System (MAKES) is introduced for the purpose of
discovery and capture of organizational knowledge. A trial
implementation has been conducted in a public organization to
achieve the objective of decision capture and navigation from a
number of meeting minutes which are autonomously organized,
classified and presented in a multi-faceted taxonomy map in both
document and content level. Key concepts such as critical decision
made, key knowledge workers, knowledge flow and the relationship
among them are elicited and displayed in predefined knowledge
model and maps. Hence, the structured knowledge can be retained,
shared and reused.
Conducting Knowledge Management with MAKES reduces work
in searching and retrieving the target decision, saves a great deal of
time and manpower, and also enables an organization to keep pace
with the knowledge life cycle. This is particularly important when
the amount of unstructured information and data grows extremely
quickly. This system approach of knowledge management can
accelerate value extraction and creation cycles of organizations.
Abstract: In this present work, the development of an avionics
system for flight data collection of a Raptor 30 V2 is carried out. For the data acquisition both onground and onboard avionics systems are developed for testing of a small-scale Unmanned Aerial Vehicle
(UAV) helicopter. The onboard avionics record the helicopter state
outputs namely accelerations, angular rates and Euler angles, in real time, and the on ground avionics system record the inputs given to
the radio controlled helicopter through a transmitter, in real time. The avionic systems are designed and developed taking into consideration
low weight, small size, anti-vibration, low power consumption, and easy interfacing. To mitigate the medium frequency vibrations
embedded on the UAV helicopter during flight, a damper is designed
and its performance is evaluated. A number of flight tests are carried
out and the data obtained is then analyzed for accuracy and repeatability and conclusions are inferred.
Abstract: This paper features the proposed modeling and design
of a Robust Decentralized Periodic Output Feedback (RDPOF)
control technique for the active vibration control of smart flexible
multimodel Euler-Bernoulli cantilever beams for a multivariable
(MIMO) case by retaining the first 6 vibratory modes. The beam
structure is modeled in state space form using the concept of
piezoelectric theory, the Euler-Bernoulli beam theory and the Finite
Element Method (FEM) technique by dividing the beam into 4 finite
elements and placing the piezoelectric sensor / actuator at two finite
element locations (positions 2 and 4) as collocated pairs, i.e., as
surface mounted sensor / actuator, thus giving rise to a multivariable
model of the smart structure plant with two inputs and two outputs.
Five such multivariable models are obtained by varying the
dimensions (aspect ratios) of the aluminum beam, thus giving rise to
a multimodel of the smart structure system. Using model order
reduction technique, the reduced order model of the higher order
system is obtained based on dominant eigen value retention and the
method of Davison. RDPOF controllers are designed for the above 5
multivariable-multimodel plant. The closed loop responses with the
RDPOF feedback gain and the magnitudes of the control input are
observed and the performance of the proposed multimodel smart
structure system with the controller is evaluated for vibration control.
Abstract: Tasks of an application program of an embedded system are managed by the scheduler of a real-time operating system
(RTOS). Most RTOSs adopt just fixed priority scheduling, which is not optimal in all cases. Some applications require earliest deadline
first (EDF) scheduling, which is an optimal scheduling algorithm.
In order to develop an efficient real-time embedded system, the
scheduling algorithm of the RTOS should be selectable. The paper presents a method to customize the scheduler using aspectoriented
programming. We define aspects to replace the fixed priority scheduling mechanism of an OSEK OS with an EDF scheduling
mechanism. By using the aspects, we can customize the scheduler
without modifying the original source code. We have applied the
aspects to an OSEK OS and get a customized operating system with
EDF scheduling. The evaluation results show that the overhead of
aspect-oriented programming is small enough.
Abstract: A separation-kernel-based operating system (OS) has been designed for use in secure embedded systems by applying formal methods to the design of the separation-kernel part. The separation kernel is a small OS kernel that provides an abstract distributed environment on a single CPU. The design of the separation kernel was verified using two formal methods, the B method and the Spin model checker. A newly designed semi-formal method, the extended state transition method, was also applied. An OS comprising the separation-kernel part and additional OS services on top of the separation kernel was prototyped on the Intel IA-32 architecture. Developing and testing of a prototype embedded application, a point-of-sale application, on the prototype OS demonstrated that the proposed architecture and the use of formal methods to design its kernel part are effective for achieving a secure embedded system having a high-assurance separation kernel.
Abstract: The photocatalytic activity efficiency of TiO2 for the degradation of Toluene in photoreactor can be enhanced by nano- TiO2/LDPE composite film. Since the amount of TiO2 affected the efficiency of the photocatalytic activity, this work was mainly concentrated on the effort to embed the high amount of TiO2 in the Polyethylene matrix. The developed photocatalyst was characterized by XRD, UV-Vis spectrophotometer and SEM. The SEM images revealed the high homogeneity of the deposition of TiO2 on the polyethylene matrix. The XRD patterns interpreted that TiO2 embedded in the PE matrix exhibited mainly in anatase form. In addition, the photocatalytic results show that the toluene removal efficiencies of 30±5%, 49±4%, 68±5%, 42±6% and 33±5% were obtained when using the catalyst loading at 0%, 10%, 15%, 25% and 50% (wt. cat./wt. film), respectively.
Abstract: Rapid advancement in computing technology brings
computers and humans to be seamlessly integrated in future. The
emergence of smartphone has driven computing era towards
ubiquitous and pervasive computing. Recognizing human activity has
garnered a lot of interest and has raised significant researches-
concerns in identifying contextual information useful to human
activity recognition. Not only unobtrusive to users in daily life,
smartphone has embedded built-in sensors that capable to sense
contextual information of its users supported with wide range
capability of network connections. In this paper, we will discuss the
classification algorithms used in smartphone-based human activity.
Existing technologies pertaining to smartphone-based researches in
human activity recognition will be highlighted and discussed. Our
paper will also present our findings and opinions to formulate
improvement ideas in current researches- trends. Understanding
research trends will enable researchers to have clearer research
direction and common vision on latest smartphone-based human
activity recognition area.
Abstract: A novel circuit for generating a signal embedded with
features about data from three sensors is presented. This suggested
circuit is making use of a resistance-to-time converter employing a
bridge amplifier, an integrator and a comparator. The second resistive
sensor (Rz) is transformed into duty cycle. Another bridge with
varying resistor, (Ry) in the feedback of an OP AMP is added in
series to change the amplitude of the resulting signal in a proportional
relationship while keeping the same frequency and duty cycle
representing proportional changes in resistors Rx and Rz already
mentioned. The resultant output signal carries three types of
information embedded as variations of its frequency, duty cycle and
amplitude.
Abstract: During the last couple of years, the degree of dependence on IT systems has reached a dimension nobody imagined to be possible 10 years ago. The increased usage of mobile devices (e.g., smart phones), wireless sensor networks and embedded devices (Internet of Things) are only some examples of the dependency of modern societies on cyber space. At the same time, the complexity of IT applications, e.g., because of the increasing use of cloud computing, is rising continuously. Along with this, the threats to IT security have increased both quantitatively and qualitatively, as recent examples like STUXNET or the supposed cyber attack on Illinois water system are proofing impressively. Once isolated control systems are nowadays often publicly available - a fact that has never been intended by the developers. Threats to IT systems don’t care about areas of responsibility. Especially with regard to Cyber Warfare, IT threats are no longer limited to company or industry boundaries, administrative jurisdictions or state boundaries. One of the important countermeasures is increased cooperation among the participants especially in the field of Cyber Defence. Besides political and legal challenges, there are technical ones as well. A better, at least partially automated exchange of information is essential to (i) enable sophisticated situational awareness and to (ii) counter the attacker in a coordinated way. Therefore, this publication performs an evaluation of state of the art Intrusion Detection Message Exchange protocols in order to guarantee a secure information exchange between different entities.
Abstract: The main objective of this project is to build an
autonomous microcontroller-based mobile robot for a local robot
soccer competition. The black competition field is equipped with
white lines to serve as the guidance path for competing robots. Two
prototypes of soccer robot embedded with the Basic Stamp II
microcontroller have been developed. Two servo motors are used as
the drive train for the first prototype whereas the second prototype
uses two DC motors as its drive train. To sense the lines, lightdependent
resistors (LDRs) supply the analog inputs for the
microcontroller. The performances of both prototypes are evaluated.
The DC motor-driven robot has produced better trajectory control
over the one using servo motors and has brought the team into the
final round.
Abstract: This paper presents preliminary results regarding system-level power awareness for FPGA implementations in wireless sensor networks. Re-configurability of field programmable gate arrays (FPGA) allows for significant flexibility in its applications to embedded systems. However, high power consumption in FPGA becomes a significant factor in design considerations. We present several ideas and their experimental verifications on how to optimize power consumption at high level of designing process while maintaining the same energy per operation (low-level methods can be used additionally). This paper demonstrates that it is possible to estimate feasible power consumption savings even at the high level of designing process. It is envisaged that our results can be also applied to other embedded systems applications, not limited to FPGA-based.
Abstract: Long number multiplications (n ≥ 128-bit) are a
primitive in most cryptosystems. They can be performed better by
using Karatsuba-Ofman technique. This algorithm is easy to
parallelize on workstation network and on distributed memory, and
it-s known as the practical method of choice. Multiplying long
numbers using Karatsuba-Ofman algorithm is fast but is highly
recursive. In this paper, we propose different designs of
implementing Karatsuba-Ofman multiplier. A mixture of sequential
and combinational system design techniques involving pipelining is
applied to our proposed designs. Multiplying large numbers can be
adapted flexibly to time, area and power criteria. Computationally
and occupation constrained in embedded systems such as: smart
cards, mobile phones..., multiplication of finite field elements can be
achieved more efficiently. The proposed designs are compared to
other existing techniques. Mathematical models (Area (n), Delay (n))
of our proposed designs are also elaborated and evaluated on
different FPGAs devices.