Abstract: We developed a new method based on quasimolecular
modeling to simulate the cavity flow in three cavity
shapes: rectangular, half-circular and bucket beer in cgs units. Each
quasi-molecule was a group of particles that interacted in a fashion
entirely analogous to classical Newtonian molecular interactions.
When a cavity flow was simulated, the instantaneous velocity vector
fields were obtained by using an inverse distance weighted
interpolation method. In all three cavity shapes, fluid motion was
rotated counter-clockwise. The velocity vector fields of the three
cavity shapes showed a primary vortex located near the upstream
corners at time t ~ 0.500 s, t ~ 0.450 s and t ~ 0.350 s, respectively.
The configurational kinetic energy of the cavities increased as time
increased until the kinetic energy reached a maximum at time t ~
0.02 s and, then, the kinetic energy decreased as time increased. The
rectangular cavity system showed the lowest kinetic energy, while
the half-circular cavity system showed the highest kinetic energy.
The kinetic energy of rectangular, beer bucket and half-circular
cavities fluctuated about stable average values 35.62 x 103, 38.04 x
103 and 40.80 x 103 ergs/particle, respectively. This indicated that the
half-circular shapes were the most suitable shape for a shrimp pond
because the water in shrimp pond flows best when we compared with
rectangular and beer bucket shape.
Abstract: The article reviews the current state of large-scale
studies about the impact of electromagnetic field on natural
environment. The scenario of investigations – simulation of natural
conditions at the workplace, taking into consideration the influence
both low and high frequency electromagnetic fields is shown.The
biological effects of low and high frequency electromagnetic fields
are below presented. Results of investigation with animals are shown.
The norms and regulations concerning the levels of electromagnetic
field intensity are reviewed.
Abstract: The paper describes the carbonate microfacies identified in the Sinjar Formation (Late Paleocene–Early Eocene) cropping out in Qara Dagh Mountain, near Sulekan Village approximately 20km south–west of Sulaimani (Iraq). One section (62m thick) has been measured in the field and closely sampled to undertake detailed microfaciesal and micropalaeontological studies to determine the formation-s age and environment of deposition. A samples were collected illustrating all the lithological changes along the section. The limestone in the studied area is hard and extremely rich in large foraminifers (soritids, rotaliids, nummulites, miliolids) and green algae (dasycladales). The investigation of the thin sections allowed us to identify the carbonate microfacies (18 types and subtypes) and the micropaleontological association (foraminifers and green algae), to determine the age of formation and to reconstruct the paleoenvironment of deposition (fore-reef, reef, back-reef). Based on the field observations and the studied thin sections, we determined three Units of a carbonate platform (I, II and III) from the base to the top of the section: Unit I with coralgal associations, Unit II is dominated by larger foraminifers and haracterized by the absence of coralgal associations, while Unit III is dominated by small foraminifers (mostly miliolids), peloids and green algae. It is partially dolomitized.
Abstract: Simulation is a very helpful and valuable work tool in
manufacturing. It can be used in industrial field allowing the
system`s behavior to be learnt and tested. Simulation provides a low
cost, secure and fast analysis tool. It also provides benefits, which
can be reached with many different system configurations. Topics to
be discussed include: Applications, Modeling, Validating, Software
and benefits of simulation. This paper provides a comprehensive
literature review on research efforts in simulation.
Abstract: Delivering streaming video over wireless is an
important component of many interactive multimedia applications
running on personal wireless handset devices. Such personal devices
have to be inexpensive, compact, and lightweight. But wireless
channels have a high channel bit error rate and limited bandwidth.
Delay variation of packets due to network congestion and the high bit
error rate greatly degrades the quality of video at the handheld
device. Therefore, mobile access to multimedia contents requires
video transcoding functionality at the edge of the mobile network for
interworking with heterogeneous networks and services. Therefore,
to guarantee quality of service (QoS) delivered to the mobile user, a
robust and efficient transcoding scheme should be deployed in
mobile multimedia transporting network. Hence, this paper
examines the challenges and limitations that the video transcoding
schemes in mobile multimedia transporting network face. Then
handheld resources, network conditions and content based mobile
and wireless video transcoding is proposed to provide high QoS
applications. Exceptional performance is demonstrated in the
experiment results. These experiments were designed to verify and
prove the robustness of the proposed approach. Extensive
experiments have been conducted, and the results of various video
clips with different bit rate and frame rate have been provided.
Abstract: Cassava bagasse is one of major biomass wastes in Thailand from starch processing industry, which contains high starch content of about 60%. The object of this study was to investigate the optimal condition for hydrothermally pretreating cassava baggasses with or without acid addition. The pretreated samples were measured reducing sugar yield directly or after enzymatic hydrolysis (alpha-amylase). In enzymatic hydrolysis, the highest reducing sugar content was obtained under hydrothermal conditions for at 125oC for 30 min. The result shows that pretreating cassava baggasses increased the efficiency of enzymatic hydrolysis. For acid hydrolysis, pretreating cassava baggasses with sulfuric acid at 120oC for 60 min gave a maximum reducing sugar yield. In this study, sulfuric acid had a greater capacity for hydrolyzing cassava baggasses than phosphoric acid. In comparison, dilute acid hydrolysis to provide a higher yield of reducing sugar than the enzymatic hydrolysis combined hydrothermal pretreatment. However, enzymatic hydrolysis in a combination with hydrothermal pretreatment was an alternative to enhance efficiency reducing sugar production from cassava bagasse.
Abstract: Firstly, research and development on RFID focuses on
manufacturing and retail sectors, because it can improve supply chain
efficiency. But, now a variety of field is considered the next research
area for Radio Frequency Identification (RFID). Although RFID is
infancy, RFID technology has great potential in power industry to
significantly reduce cost, and improve quality of power supply. To
complement the limitation of RFID, we adopt the WSN (Wireless
Sensor Network) technology. However, relevant experience is limited,
the challenge will be to derive requirement from business practice and
to determine whether it is possible or not. To explore this issue, we
conduct a case study on implementing power facility management
system using RFID/WSN in Korea Electric Power Corporation
(KEPCO). In this paper we describe requirement from power industry.
And we introduce design and implementation of the test bed.
Abstract: After a strong earthquake occurs, a secondary disaster due to strong aftershocks, flood, landslide or heavy snow can possible to occur and the secondary disaster due to resident-s action also can possible to happen. However, until now seldom researchers have paid attention at it. This paper focused on the Inhabitant-s action after the strong earthquake occurs when a terrible even becomes calm. An inappropriate behavior of people with disadvantaged climate after the worse earthquake can bring a tragedy to their life.
Abstract: In this paper, design, fabrication and coupled
multifield analysis of hollow out-of-plane silicon microneedle array
with piezoelectrically actuated microfluidic device for transdermal
drug delivery (TDD) applications is presented. The fabrication
process of silicon microneedle array is first done by series of
combined isotropic and anisotropic etching processes using
inductively coupled plasma (ICP) etching technology. Then coupled
multifield analysis of MEMS based piezoelectrically actuated device
with integrated 2×2 silicon microneedle array is presented. To predict
the stress distribution and model fluid flow in coupled field analysis,
finite element (FE) and computational fluid dynamic (CFD) analysis
using ANSYS rather than analytical systems has been performed.
Static analysis and transient CFD analysis were performed to predict
the fluid flow through the microneedle array. The inlet pressure from
10 kPa to 150 kPa was considered for static CFD analysis. In the
lumen region fluid flow rate 3.2946 μL/min is obtained at 150 V for
2×2 microneedle array. In the present study the authors have
performed simulation of structural, piezoelectric and CFD analysis
on three dimensional model of the piezoelectrically actuated
mcirofluidic device integrated with 2×2 microneedle array.
Abstract: The dissolution of spherical particles in liquids is analyzed dynamically. Here, we consider the case the dissolution of solute yields a solute-free solid phase in the outer portion of a particle. As dissolution proceeds, the interface between the undissolved solid phase and the solute-free solid phase moves towards the center of the particle. We assume that there exist two resistances for the diffusion of solute molecules: the resistance due to the solute-free portion of the particle and that due to a surface layer near solid-liquid interface. In general, the equation governing the dynamic behavior of dissolution needs to be solved numerically. However, analytical expressions for the temporal variation of the size of the undissoved portion of a particle and the variation of dissolution time can be obtained in some special cases. The present analysis takes the effect of variable bulk solute concentration on dissolution into account.
Abstract: Wide applicability of concurrent programming
practices in developing various software applications leads to
different concurrency errors amongst which data race is the most
important. Java provides greatest support for concurrent
programming by introducing various concurrency packages. Aspect
oriented programming (AOP) is modern programming paradigm
facilitating the runtime interception of events of interest and can be
effectively used to handle the concurrency problems. AspectJ being
an aspect oriented extension to java facilitates the application of
concepts of AOP for data race detection. Volatile variables are
usually considered thread safe, but they can become the possible
candidates of data races if non-atomic operations are performed
concurrently upon them. Various data race detection algorithms have
been proposed in the past but this issue of volatility and atomicity is
still unaddressed. The aim of this research is to propose some
suggestions for incorporating certain conditions for data race
detection in java programs at the volatile fields by taking into account
support for atomicity in java concurrency packages and making use
of pointcuts. Two simple test programs will demonstrate the results
of research. The results are verified on two different Java
Development Kits (JDKs) for the purpose of comparison.
Abstract: In the present study, a numerical analysis is carried
out to investigate unsteady MHD (magneto-hydrodynamic) flow and
heat transfer of a non-Newtonian second grade viscoelastic fluid
over an oscillatory stretching sheet. The flow is induced due to an
infinite elastic sheet which is stretched oscillatory (back and forth) in
its own plane. Effect of viscous dissipation and joule heating are
taken into account. The non-linear differential equations governing
the problem are transformed into system of non-dimensional
differential equations using similarity transformations. A newly
developed meshfree numerical technique Element free Galerkin
method (EFGM) is employed to solve the coupled non linear
differential equations. The results illustrating the effect of various
parameters like viscoelastic parameter, Hartman number, relative
frequency amplitude of the oscillatory sheet to the stretching rate and
Eckert number on velocity and temperature field are reported in
terms of graphs and tables. The present model finds its application in
polymer extrusion, drawing of plastic films and wires, glass, fiber
and paper production etc.
Abstract: Introduction: Visual performance is an important factor in sport excellence. Visual involvement in a sport varies according to environmental demands associated with that sport. These environmental demands are matched by a task specific motor response. The purpose of this study was to determine if sport specific exercises will improve the visual performance of male rugby players, in order to achieve maximal results on the sports field. Materials & Methods: Twenty six adult male rugby players, aged 16-22, were chosen as subjects. In order to evaluate the effect of sport specific exercises on visual skills, a pre-test - post-test experimental group design was adopted for the study. Results: Significant differences (p≤0.05) were seen in the focussing, tracking, vergence, sequencing, eye-hand coordination and visualisation components Discussion & Conclusions: Sport specific exercises improved visual skills in rugby players which may provide them with an advantage over their opponents. This study suggests that these training programs and participation in regular on-line EyeDrills sports vision exercises (www.eyedrills.co.za) aimed at improving the athlete-s visual coordination, concentration, focus, hand-eye co-ordination, anticipation and motor response should be incorpotated in the rugby players exercise regime.
Abstract: The impact assessment in its various forms has
recently become a very important part of policy-making and
legislation in many different countries. Regulatory impact assessment
(RIA) is yet another set of analytical methods deployed in the
legislation of the European Union, of many developed countries as
well as in many developing ones such as Mexico, Malaysia and
Philippines. The aim of this paper is to provide a theoretical
background for economic models in regulatory impact assessment
and an overview of their application especially on the financial
market in the Czech Republic. We found out an inadequate
application of these models, what makes room for further research in
this field.
Abstract: A multiple-option analytical model for the evaluation of the energy performance and distribution of aerodynamic forces acting on a vertical-axis Darrieus wind turbine depending on both rotor architecture and operating conditions is presented. For this purpose, a numerical algorithm, capable of generating the desired rotor conformation depending on design geometric parameters, is coupled to a Single/Double-Disk Multiple-Streamtube Blade Element – Momentum code. Both single and double-disk configurations are analyzed and model predictions are compared to literature experimental data in order to test the capability of the code for predicting rotor performance. Effective airfoil characteristics based on local blade Reynolds number are obtained through interpolation of literature low-Reynolds airfoil databases. Some corrections are introduced inside the original model with the aim of simulating also the effects of blade dynamic stall, rotor streamtube expansion and blade finite aspect ratio, for which a new empirical relationship to better fit the experimental data is proposed. In order to predict also open field rotor operation, a freestream wind shear profile is implemented, reproducing the effect of atmospheric boundary layer.
Abstract: Virtual Reality Modelling Language (VRML) is description language, which belongs to a field Window on World virtual reality system. The file, which is in VRML format, can be interpreted by VRML explorer in three-dimensional scene. VRML was created with aim to represent virtual reality on Internet easier. Development of 3D graphic is connected with Silicon Graphic Corporation. VRML 2.0 is the file format for describing interactive 3D scenes and objects. It can be used in collaboration with www, can be used for 3D complex representations creating of scenes, products or VR applications VRML 2.0 enables represent static and animated objects too. Interesting application of VRML is in area of manufacturing systems presentation.
Abstract: The increasing number of senior population gradually
causes to demand the use of information and communication
technology for their satisfactory lives. This paper presents the
development of an integrated TV based system which offers an
opportunity to provide value added services to a large number of
elderly citizens, and thus helps improve their quality of life. The
design philosophy underlying this paper is to fulfill both technological
and human aspects. The balance between these two dimensions has
been currently stressed as a crucial element for the design of usable
systems in real use, particularly to the elderly who have physical and
mental decline. As the first step to achieve it, we have identified
human and social factors that affect the elder-s quality of life by a
literature review, and based on them, build four fundamental services:
information, healthcare, learning and social network services.
Secondly, the system architecture, employed technologies and the
elderly-friendly system design considerations are presented. This
reflects technological and human perspectives in terms of the system
design. Finally, we describe some scenarios that illustrate the
potentiality of the proposed system to improve elderly people-s quality
of life.
Abstract: The six sigma method is a project-driven management approach to improve the organization-s products, services, and processes by continually reducing defects in the organization. Understanding the key features, obstacles, and shortcomings of the six sigma method allows organizations to better support their strategic directions, and increasing needs for coaching, mentoring, and training. It also provides opportunities to better implement six sigma projects. The purpose of this paper is the survey of six sigma process and its impact on the organizational productivity. So I have studied key concepts , problem solving process of six sigmaas well as the survey of important fields such as: DMAIC, six sigma and productivity applied programme, and other advantages of six sigma. In the end of this paper, present research conclusions. (direct and positive relation between six sigma and productivity)
Abstract: Despite many success stories of manufacturing safety, many organizations are still reluctant, perceiving it as cost increasing and time consuming. The clear contributor may be due to the use of lagging indicators rather than leading indicator measures. The study therefore proposes a combinatorial model for determining the best safety strategy. A combination theory and cost benefit analysis was employed to develop a monetary saving / loss function in terms value of preventions and cost of prevention strategy. Documentations, interviews and structured questionnaire were employed to collect information on Before-And-After safety programme records from a Tobacco company between periods of 1993-2001(for pre-safety) and 2002-2008 (safety period) for the model application. Three combinatorial alternatives A, B, C were obtained resulting into 4, 6 and 4 strategies respectively with PPE and Training being predominant. A total of 728 accidents were recorded for a 9 year period of pre-safety programme and 163 accidents were recorded for 7 years period of safety programme. Six preventions activities (alternative B) yielded the best results. However, all the years of operation experienced except year 2004. The study provides a leading resources for planning successful safety programme
Abstract: In this research a comparison between k-epsilon and
LES model for a deoiling hydrocyclone is conducted. Flow field of
hydrocyclone is obtained by three-dimensional simulations with
OpenFOAM code. Potential of prediction for both methods of this
complex swirl flow is discussed. Large eddy simulation method
results have more similarity to experiment and its results are
presented in figures from different hydrocyclone cross sections.