Abstract: This paper presents the vibrations suppression of a thermoelastic beam subject to sudden heat input by a distributed piezoelectric actuators. An optimization problem is formulated as the minimization of a quadratic functional in terms of displacement and velocity at a given time and with the least control effort. The solution method is based on a combination of modal expansion and variational approaches. The modal expansion approach is used to convert the optimal control of distributed parameter system into the optimal control of lumped parameter system. By utilizing the variational approach, an explicit optimal control law is derived and the determination of the corresponding displacement and velocity is reduced to solving a set of ordinary differential equations.
Abstract: Flood management is one of the important fields in
urban storm water management. Floods are influenced by the
increase of huge storm event, or improper planning of the area. This study mainly provides the flood protection in four stages; planning,
flood event, responses and evaluation. However it is most effective then flood protection is considered in planning/design and
evaluation stages since both stages represent the land development of the area. Structural adjustments are often more reliable than nonstructural
adjustments in providing flood protection, however
structural adjustments are constrained by numerous factors such as
political constraints and cost. Therefore it is important to balance
both adjustments with the situation. The technical decisions provided
will have to be approved by the higher-ups who have the power to
decide on the final solution. Costs however, are the biggest factor in
determining the final decision. Therefore this study recommends
flood protection system should have been integrated and enforces
more in the early stages (planning and design) as part of the storm
water management plan. Factors influencing the technical decisions
provided should be reduced as low as possible to avoid a reduction in
the expected performance of the proposed adjustments.
Abstract: It is crucial to quantitatively evaluate the treatment of
epilepsy patients. This study was undertaken to test the hypothesis that
compared to the healthy control subjects, the epilepsy patients have
abnormal resting-state connectivity. In this study, we used the
imaginary part of coherency to measure the resting-state connectivity.
The analysis results shown that compared to the healthy control
subjects, epilepsy patients tend to have abnormal rhythm brain
connectivity over their epileptic focus.
Abstract: In this research, Response Surface Methodology (RSM) is used to investigate the effect of four controllable input variables namely: discharge current, pulse duration, pulse off time and applied voltage Surface Roughness (SR) of on Electrical Discharge Machined surface. To study the proposed second-order polynomial model for SR, a Central Composite Design (CCD) is used to estimation the model coefficients of the four input factors, which are alleged to influence the SR in Electrical Discharge Machining (EDM) process. Experiments were conducted on AISI D2 tool steel with copper electrode. The response is modeled using RSM on experimental data. The significant coefficients are obtained by performing Analysis of Variance (ANOVA) at 5% level of significance. It is found that discharge current, pulse duration, and pulse off time and few of their interactions have significant effect on the SR. The model sufficiency is very satisfactory as the Coefficient of Determination (R2) is found to be 91.7% and adjusted R2-statistic (R2 adj ) 89.6%.
Abstract: This project relates to a two-wheeled self balancing
robot for transferring loads on different locations along a path. This
robot specifically functions as a dual mode navigation to navigate
efficiently along a desired path. First, as a plurality of distance
sensors mounted at both sides of the body for collecting information
on tilt angle of the body and second, as a plurality of speed sensors
mounted at the bottom of the body for collecting information of the
velocity of the body in relative to the ground. A microcontroller for
processing information collected from the sensors and configured to
set the path and to balance the body automatically while a processor
operatively coupled to the microcontroller and configured to compute
change of the tilt and velocity of the body. A direct current motor
operatively coupled to the microcontroller for controlling the wheels
and characterized in that a remote control is operatively coupled to
the microcontroller to operate the robot in dual navigation modes.
Abstract: A variable structure model reference adaptive control
(VS-MRAC) strategy for active steering assistance of a two wheel
steering car is proposed. An ideal steering system with fixed
properties and moving on an ideal road is used as the reference
model, and the active steering assistance system is forced to attain
the same behavior as the reference model. The proposed system can
treat the nonlinear relationships between the side slip angles and
lateral forces on tire, and the uncertainties on friction of the road
surface, whose compensation are very important under critical
situations. Simulation results show improvements on yaw rate and
side slip.
Abstract: Corrosion of metallic water pipelines buried below
ground surface is a function of the nature of the surrounding soil and
groundwater. This gives the importance of knowing the physical and
chemical characteristics of the pipe-s surrounding environment. The
corrosion of externally – unprotected metallic water pipelines,
specially ductile iron pipes, in localities with aggressive soil
conditions is becoming a significant problem. Anticorrosive
protection for metallic water pipelines, their fittings and accessories
is very important, because they may be attached by corrosion with
time. The tendency of a metallic substrate to corrode is a function of
the surface characteristics of the metal and of the metal/protective
film interface, the physical, electrical and electrochemical properties
of the film, and the nature of the environment in which the pipelines
system is placed. In this work the authors have looked at corrosion
problems of water pipelines and their control. The corrosive
properties of groundwater and soil environments are reviewed, and
parameters affecting corrosion are discussed. The purpose of this
work is to provide guidelines for materials selection in water and soil
environments, and how the water pipelines can be protected against
metallic corrosion.
Abstract: One of the approaches enabling people with amputated
limbs to establish some sort of interface with the real world includes
the utilization of the myoelectric signal (MES) from the remaining
muscles of those limbs. The MES can be used as a control input to a
multifunction prosthetic device. In this control scheme, known as the
myoelectric control, a pattern recognition approach is usually utilized
to discriminate between the MES signals that belong to different
classes of the forearm movements. Since the MES is recorded using
multiple channels, the feature vector size can become very large. In
order to reduce the computational cost and enhance the generalization
capability of the classifier, a dimensionality reduction method is
needed to identify an informative yet moderate size feature set. This
paper proposes a new fuzzy version of the well known Fisher-s
Linear Discriminant Analysis (LDA) feature projection technique.
Furthermore, based on the fact that certain muscles might contribute
more to the discrimination process, a novel feature weighting scheme
is also presented by employing Particle Swarm Optimization (PSO)
for estimating the weight of each feature. The new method, called
PSOFLDA, is tested on real MES datasets and compared with other
techniques to prove its superiority.
Abstract: Wall-surface jet induced by the dielectric barrier
discharge (DBD) has been proposed as an actuator for active flow
control in aerodynamic applications. Discharge plasma evolution of
the DBD plasma actuator was simulated based on a simple fluid model,
in which the electron, one type of positive ion and negative ion were
taken into account. Two-dimensional simulation was conducted, and
the results are in agreement with the insights obtained from
experimental studies. The simulation results indicate that the discharge
mode changes depending on applied voltage slope; when the applied
voltage is positive-going with high applied voltage slope, the
corona-type discharge mode turns into the streamer-type discharge
mode and the threshold voltage slope is around 300 kV/ms in this
simulation. The characteristics of the electrohydrodynamic (EHD)
force, which is the source of the wall-surface jet, also change
depending on the discharge mode; the tentative peak value of the EHD
force during the positive-going voltage phase is saturated by the
periodical formation of the streamer-type discharge.
Abstract: In this paper, the position control of an electronic
throttle actuator is outlined. The dynamic behavior of the actuator is
described with the help of an uncertain plant model. This motivates
the controller design based on the ideas of higher-order slidingmodes.
As a consequence anti-chattering techniques can be omitted.
It is shown that the same concept is applicable to estimate unmeasureable
signals. The control law and the observer are implemented on
an electronic control unit. Results achieved by numerical simulations
and real world experiments are presented and discussed.
Abstract: Evaporator is an important and widely used heat
exchanger in air conditioning and refrigeration industries. Different
methods have been used by investigators to increase the heat transfer
rates in evaporators. One of the passive techniques to enhance heat
transfer coefficient is the application of microfin tubes. The
mechanism of heat transfer augmentation in microfin tubes is
dependent on the flow regime of two-phase flow. Therefore many
investigations of the flow patterns for in-tube evaporation have been
reported in literatures. The gravitational force, surface tension and
the vapor-liquid interfacial shear stress are known as three dominant
factors controlling the vapor and liquid distribution inside the tube. A
review of the existing literature reveals that the previous
investigations were concerned with the two-phase flow pattern for
flow boiling in horizontal tubes [12], [9]. Therefore, the objective of
the present investigation is to obtain information about the two-phase
flow patterns for evaporation of R-134a inside horizontal smooth and
microfin tubes. Also Investigation of heat transfer during flow
boiling of R-134a inside horizontal microfin and smooth tube have
been carried out experimentally The heat transfer coefficients for
annular flow in the smooth tube is shown to agree well with Gungor
and Winterton-s correlation [4]. All the flow patterns occurred in the
test can be divided into three dominant regimes, i.e., stratified-wavy
flow, wavy-annular flow and annular flow. Experimental data are
plotted in two kinds of flow maps, i.e., Weber number for the vapor
versus weber number for the liquid flow map and mass flux versus
vapor quality flow map. The transition from wavy-annular flow to
annular or stratified-wavy flow is identified in the flow maps.
Abstract: Equipment miniaturisation offers several opportunities such as an increased surface-to-volume ratio and higher heat transfer coefficients. However, moving towards small-diameter channels demands extra attention to fouling, reliability and stable operation of the system. The present investigation explores possibilities to enhance the stability of the once-through micro evaporator by reducing its flow boiling induced pressure fluctuations. Experimental comparison shows that the measured reduction factor approaches a theoretically derived value. Pressure fluctuations are reduced by a factor of ten in the solid conical channel and a factor of 15 in the porous conical channel. This presumably leads to less backflow and therefore to a better flow control.
Abstract: Huge losses in apple production are caused by pathogens that cannot be seen shortly after harvest. After-harvest thermotherapy treatments can considerably improve control of storage diseases on apples and become an alternative to chemical pesticides. In the years 2010-2012 carried out research in this area. Apples of 'Topaz' cultivar were harvested at optimal maturity time for long storage and subject to water bath treatment at 45, 50, 52, 55°C for 60, 120, 180 and 240 seconds. The control was untreated fruits. After 12 and 24 weeks and during so called simulated trade turnover the fruits were checked for their condition and the originators of diseases were determined by using the standard phytopathological methods. The most common originator of 'Topaz' apple infection during storage were the fungi of genus Gloeosporium. In this paper it was proven that for effective protection of 'Topaz' apples against diseases, thermotherapy by using water treatments at temperature range of 50-52°C is quite sufficient.
Abstract: The two significant overvoltages in power system,
switching overvoltage and lightning overvoltage, are investigated in
this paper. Firstly, the effect of various power system parameters on
Line Energization overvoltages is evaluated by simulation in ATP.
The dominant parameters include line parameters; short-circuit
impedance and circuit breaker parameters. Solutions to reduce
switching overvoltages are reviewed and controlled closing using
switchsync controllers is proposed as proper method.
This paper also investigates lightning overvoltages in the
overhead-cable transition. Simulations are performed in
PSCAD/EMTDC. Surge arresters are applied in both ends of cable to
fulfill the insulation coordination. The maximum amplitude of
overvoltages inside the cable is surveyed which should be of great
concerns in insulation coordination studies.
Abstract: In studying the possibility of using plants as
rhizoremediators, barley and grass mixture which showed resistance
to various concentrations of oil were selected. The minimum
inhibitory effect of oil on these plants by morphological parameters
such as survival of plants, length and biomass of shoot and root
compared with the control was showed. In determining physiological
parameters, a slight decrease in the number of chlorophyll a and b in
the leaves of plants was noted. The differences in the ratio of the total
surface of the roots to the work surface with the growth of plants in
soil with oil in the study of adsorption of the root surface were
showed.
Abstract: We propose a control design scheme that aims to
prevent undesirable liquid outpouring and suppress sloshing during
the forward and backward tilting phases of the pouring process, for
the case of liquid containers carried by manipulators. The proposed
scheme combines a partial inverse dynamics controller with a PID
controller, tuned with the use of a “metaheuristic" search algorithm.
The “metaheuristic" search algorithm tunes the PID controller based
on simulation results of the plant-s linearization around the operating
point corresponding to the critical tilting angle, where outpouring
initiates. Liquid motion is modeled using the well-known pendulumtype
model. However, the proposed controller does not require
measurements of the liquid-s motion within the tank.
Abstract: Sixteen female Holstein calves allocated in three
treatments including: 1: control, 2: fed raw fiber concentrate (RFC)
for 45 days and 3: fed RFC for 90 days. RFC supplement (Vitacel®
200) was added to milk immediately before feeding (10 g/L milk).
Withers height and body weights of calves were measured monthly.
Individual dry matter intake was recorded daily. Blood samples were
taken monthly. The result showed that calves consumed RFC had
significantly greater weaning and final body weight. Treatment effect
on dry matter intake was not significant (p>0.05). Calves fed RFC
had better feed efficiency. Withers height of calves fed RFC were
taller than the control group (p
Abstract: Growth and mineral nutrient elemental content were
studied in Mokara chark kuan pink terrestrial orchid and wild
Lantana camara weed agroecosystem. The treated subplots were
encircled with L. camara plants and sprayed weekly with L. camara
10% leaf aqueous extract. Allelopathic interactions were possible
through extensive invading root of L. camara plants into the treated
orchid subplots and weekly L. camara leaf aqueous extract
sprayings. Orchid growth was not significantly different in between
the control and treated plots, but chlorosis and yellowish patches of
leaves were observed in control orchid leaves. Nitrogen content in L.
camara leaf was significantly higher than in orchid leaf, the order of
importance of mineral nutrient contents in L. camara leaf was
K>Mg>Na>N. In treated orchid leaf, the order of importance was
N>K>Mg>Na. Orchid leaf N content from the treated plot was
higher than control, but Mg and Na contents were almost similar.
Abstract: The effect of seed inoculation by VA- mycorrhiza and
different levels of phosphorus fertilizer on growth and yield of
sunflower (Azargol cultivar) was studied in experiment farm of
Islamic Azad University, Karaj Branch during 2008 growing season.
The experiment treatments were arranged in factorial based on a
complete randomized block design with three replications. Four
phosphorus fertilizer levels of 25%, 50% 75% and 100% P
recommended with two levels of Mycorrhiza: with and without
Mycorrhiza (control) were assigned in a factorial combination.
Results showed that head diameter, number of seeds in head, seed
yield and oil yield were significantly higher in inoculated plants than
in non-inoculated plants. Head diameter, number of seeds in head,
1000 seeds weight, biological yield, seed yield and oil yield increased
with increasing P level above 75% P recommended in non-inoculated
plants, whereas no significant difference was observed between 75%
and 100% P recommended. The positive effect of mycorrhizal
inoculation decreased with increasing P levels due to decreased
percent root colonization at higher P levels. According to the results
of this experiment, application of mycorrhiza in present of 50% P
recommended had an appropriate performance and could increase
seed yield and oil production to an acceptable level, so it could be
considered as a suitable substitute for chemical phosphorus fertilizer
in organic agricultural systems.
Abstract: Fuzzy logic can be used when knowledge is
incomplete or when ambiguity of data exists. The purpose of
this paper is to propose a proactive fuzzy set- based model for
reacting to the risk inherent in investment activities relative to
a complete view of portfolio management. Fuzzy rules are
given where, depending on the antecedents, the portfolio size
may be slightly or significantly decreased or increased. The
decision maker considers acceptable bounds on the proportion
of acceptable risk and return. The Fuzzy Controller model
allows learning to be achieved as 1) the firing strength of each
rule is measured, 2) fuzzy output allows rules to be updated,
and 3) new actions are recommended as the system continues
to loop. An extension is given to the fuzzy controller that
evaluates potential financial loss before adjusting the
portfolio. An application is presented that illustrates the
algorithm and extension developed in the paper.