Abstract: Opportunistic network is a kind of Delay Tolerant Networks (DTN) where the nodes in this network come into contact with each other opportunistically and communicate wirelessly and, an end-to-end path between source and destination may have never existed, and disconnection and reconnection is common in the network. In such a network, because of the nature of opportunistic network, perhaps there is no a complete path from source to destination for most of the time and even if there is a path; the path can be very unstable and may change or break quickly. Therefore, routing is one of the main challenges in this environment and, in order to make communication possible in an opportunistic network, the intermediate nodes have to play important role in the opportunistic routing protocols. In this paper we proposed an Adaptive Fuzzy Routing in opportunistic network (AFRON). This protocol is using the simple parameters as input parameters to find the path to the destination node. Using Message Transmission Count, Message Size and Time To Live parameters as input fuzzy to increase delivery ratio and decrease the buffer consumption in the all nodes of network.
Abstract: Triglycerides and their derivatives are considered as viable alternatives for diesel fuels. Rice bran oil is used as diesel fuel. Highly viscous rice bran oil can be reduced by blending it with diesel fuel. The present research is aimed to investigate experimentally the performance, exhaust emission and combustion characteristics of a direct injection (DI) diesel engine, typically used in agricultural sector, over the entire load range when fuelled with rice bran oil and diesel fuel blends, RB10 (10% rice bran oil + 90% diesel fuel) to RB50. The performance, emission and combustion parameters of RB20 were found to be very close to neat diesel fuel (ND). The injector opening pressure (IOP) undoubtedly is of prime importance in diesel engine operation. Performance, emission and combustion characteristics with RB30 at enhanced IOPs are better than ND. Improved premixed heat release rate were noticed with RB30 when the IOP is enhanced.
Abstract: Microwave heating process has been developed about sixty years while measurement system has also progressed. Because of irradiation of high frequency of microwave, researchers have been utilized many costly technical instrument measuring parameters to evaluate the performance of microwave heating system. Therefore, this paper is intended to present an easier and feasible efficiency measurement method. It can help inspecting efficiency of microwave heating system with good accuracy, while the method can also give reference to optimizing procedure for microwave heating system for various load material
Abstract: According to investigating impact of complexity of
stereoscopic frame pairs on stereoscopic video coding and
transmission, a new rate control algorithm is presented. The proposed
rate control algorithm is performed on three levels: stereoscopic group
of pictures (SGOP) level, stereoscopic frame (SFrame) level and
frame level. A temporal-spatial frame complexity model is firstly
established, in the bits allocation stage, the frame complexity, position
significance and reference property between the left and right frames
are taken into account. Meanwhile, the target buffer is set according to
the frame complexity. Experimental results show that the proposed
method can efficiently control the bitrates, and it outperforms the fixed
quantization parameter method from the rate distortion perspective,
and average PSNR gain between rate-distortion curves (BDPSNR) is
0.21dB.
Abstract: In manufacturing industries, development of measurement leads to increase the number of monitoring variables and eventually the importance of multivariate control comes to the fore. Statistical process control (SPC) is one of the most widely used as multivariate control chart. Nevertheless, SPC is restricted to apply in processes because its assumption of data as following specific distribution. Unfortunately, process data are composed by the mixture of several processes and it is hard to estimate as one certain distribution. To alternative conventional SPC, therefore, nonparametric control chart come into the picture because of the strength of nonparametric control chart, the absence of parameter estimation. SVDD based control chart is one of the nonparametric control charts having the advantage of flexible control boundary. However,basic concept of SVDD has been an oversight to the important of data characteristic, density distribution. Therefore, we proposed DW-SVDD (Density Weighted SVDD) to cover up the weakness of conventional SVDD. DW-SVDD makes a new attempt to consider dense of data as introducing the notion of density Weight. We extend as control chart using new proposed SVDD and a simulation study of various distributional data is conducted to demonstrate the improvement of performance.
Abstract: Carbon dioxide capture process has been simulated
and studied under different process conditions. It has been shown
that several process parameters such as lean amine temperature,
number of adsorber stages, number of stripper stages and stripper
pressure affect different process conditions and outputs such as
carbon dioxide removal and reboiler duty. It may be concluded that
the simulation of carbon dioxide capture process can help to estimate
the best process conditions.
Abstract: A DC servomotor position control system using a Fuzzy Logic Sliding mode Model Following Control or FLSMFC approach is presented. The FLSMFC structure consists of an integrator and variable structure system. The integral control is introduced into it in order to eliminated steady state error due to step and ramp command inputs and improve control precision, while the fuzzy control would maintain the insensitivity to parameter variation and disturbances. The FLSMFC strategy is implemented and applied to a position control of a DC servomotor drives. Experimental results indicated that FLSMFC system performance with respect to the sensitivity to parameter variations is greatly reduced. Also, excellent control effects and avoids the chattering phenomenon.
Abstract: The performance of modified Fenton (MF) treatment
to promote PAH oxidation in artificially contaminated soil was
investigated in packed soil column with a hydrogen peroxide (H2O2)
delivery system simulating in situ injection. Soil samples were spiked
with phenanthrene (low molecular weight PAH) and fluoranthene
(high molecular weight PAH) to an initial concentration of 500
mg/kg dried soil each. The effectiveness of process parameters
H2O2/soil, iron/soil, chelating agent/soil weight ratios and reaction
time were studied using a 24 three level factorial design experiments.
Statistically significant quadratic models were developed using
Response Surface Methodology (RSM) for degrading PAHs from the
soil samples. Optimum operating condition was achieved at mild
range of H2O2/soil, iron/soil and chelating agent/soil weight ratios,
indicating cost efficient method for treating highly contaminated
lands.
Abstract: This paper presents the development of a hybrid
thermal model for the EVO Electric AFM 140 Axial Flux Permanent
Magnet (AFPM) machine as used in hybrid and electric vehicles. The
adopted approach is based on a hybrid lumped parameter and finite
difference method. The proposed method divides each motor
component into regular elements which are connected together in a
thermal resistance network representing all the physical connections
in all three dimensions. The element shape and size are chosen
according to the component geometry to ensure consistency. The
fluid domain is lumped into one region with averaged heat transfer
parameters connecting it to the solid domain. Some model parameters
are obtained from Computation Fluid Dynamic (CFD) simulation and
empirical data. The hybrid thermal model is described by a set of
coupled linear first order differential equations which is discretised
and solved iteratively to obtain the temperature profile. The
computation involved is low and thus the model is suitable for
transient temperature predictions. The maximum error in temperature
prediction is 3.4% and the mean error is consistently lower than the
mean error due to uncertainty in measurements. The details of the
model development, temperature predictions and suggestions for
design improvements are presented in this paper.
Abstract: Microwave energy can be used for drying purpose. It is unique process. It is distinctly different from conventional drying process. It is advantageous over conventional drying / heating processes. When microwave energy is used for drying purpose, the process can be accelerated with a better control to achieve uniform heating, more conversion efficiency, selective drying and ultimately improved product quality of the output. Also, less floor space and compact system are the added advantages. Existing low power microwave drying system is to be modified with suitable applicator. Appropriate sensors are to be used to measure parameters like moisture, temperature, weight of sample. Suitable high tech controller is to be used to control microwave power continuously from minimum to maximum. Phase - controller, cycle - controller and PWM - controller are some of the advanced power control techniques. It has been proposed to work on turmeric using high-tech phase controller to control the microwave power conveniently. The drying of turmeric with microwave energy employing phase controller gives better results as formulated in this paper and hence new approach of processing turmeric will open future doors of profit making to allied industries and the farmers.
Abstract: To improve the dynamics response of the vehicle
passive suspension, a two-terminal mass is suggested to connect in
parallel with the suspension strut. Three performance criteria, tire grip,
ride comfort and suspension deflection, are taken into consideration to
optimize the suspension parameters. However, the three criteria are
conflicting and non-commensurable. For this reason, the Chebyshev
goal programming method is applied to find the best tradeoff among
the three objectives. A simulation case is presented to describe the
multi-objective optimization procedure. For comparison, the
Chebyshev method is also employed to optimize the design of a
conventional passive suspension. The effectiveness of the proposed
design method has been clearly demonstrated by the result. It is also
shown that the suspension with a two-terminal mass in parallel has
better performance in terms of the three objectives.
Abstract: Motion control of flexible arms is more difficult than
that of rigid arms, however utilizing its dynamics enables improved
performance such as a fast motion in short operation time. This paper
investigates a ball throwing robot with one rigid link and one flexible
link. This robot throws a ball at a set speed with a proper control torque.
A mathematical model of this ball throwing robot is derived through
Hamilton’s principle. Several patterns of torque input are designed and
tested through the proposed simulation models. The parameters of
each torque input pattern is optimized and determined by chaos
embedded vector evaluated particle swarm optimization (CEVEPSO).
Then, the residual vibration of the manipulator after throwing is
suppressed with input shaping technique. Finally, a real experiment is
set up for the model checking.
Abstract: Accurate evaluation of damping ratios involving soilstructure interaction (SSI) effects is the prerequisite for seismic design of in-situ buildings. This study proposes a combined approach to identify damping ratios of SSI systems based on ambient excitation technique. The proposed approach is illustrated with main test process, sampling principle and algorithm steps through an engineering example, as along with its feasibility and validity. The proposed approach is employed for damping ratio identification of 82 buildings in Xi-an, China. Based on the experimental data, the variation range and tendency of damping ratios of these SSI systems, along with the preliminary influence factor, are shown and discussed. In addition, a fitting curve indicates the relation between the damping ratio and fundamental natural period of SSI system.
Abstract: In this study, cometabolic biodegradation of
chloroform was experimented with mixed cultures in the presence of
various organic solvents like methanol, ethanol, isopropanol, acetone,
acetonitrile and toluene as these are predominant discharges in
pharmaceutical industries. Toluene and acetone showed higher
specific chloroform degradation rate when compared to other
compounds. Cometabolic degradation of chloroform was further
confirmed by observation of free chloride ions in the medium. An
extended Haldane model, incorporating the inhibition due to
chloroform and the competitive inhibition between primary
substrates, was developed to predict the biodegradation of primary
substrates, cometabolic degradation of chloroform and the biomass
growth. The proposed model is based on the use of biokinetic
parameters obtained from single substrate degradation studies. The
model was able to satisfactorily predict the experimental results of
ternary and quaternary mixtures. The proposed model can be used for
predicting the performance of bioreactors treating discharges from
pharmaceutical industries.
Abstract: The work presented in this study is related to an
energy system analysis based on passive cooling system for
dwellings. It consists to solar chimney energy performances
determination versus geometrical and environmental considerations
as the size and inlet width conditions of the chimney. Adrar site
located in the southern region of Algeria is chosen for this study
according to ambient temperature and solar irradiance technical data
availability. Obtained results are related to the glazing temperature
distributions, the chimney air flow and internal wall temperatures.
The air room change per hour (ACH) parameter, the outlet air
velocity and mass air flow rate are also determined. It is shown that
the chimney width has a significant effect on energy performances
compared to its entry size. A good agreement is observed between
these results and those obtained by others from the literature.
Abstract: The enzyme alkaline protease production was determined under
solid state fermentation using the soil bacteria Serratia marcescens
sp7. The maximum production was obtained from wheat bran
medium than ground nut shell and chemically defined medium. The
physiological fermentation factors such as pH of the medium (pH 8),
Temperature (40oC) and incubation time (48 hrs) played a vital role
in alkaline protease production in all the above. 100Mm NaCl has
given better resolution during elution of the enzymes. The enzyme
production was found to be associated with growth of the bacterial
culture.
Abstract: Impaired fertility may be the result of indirect
consumption of anti-fertility agents through food. Monosodium
glutamate (MSG) has been widely used as food additive, flavour
enhancer and included in vaccines. This study focuses in determining
the gonadotoxic and cytotoxic effect of MSG on selected sperm
parameters such as sperm viability, sperm membrane integrity and
testes cytoarchitecture of male mice via histological examination to
determine its effect on spermatogenesis. Twenty-four Mus musculus
were randomly divided into 4 groups and given intraperitoneal
injections (IP) daily for 14 days of different MSG concentrations at
250, 500 and 1000mg/kg MSG to body weight to induce obesity.
Saline was given to control group. Mice were sacrificed and analysis
revealed abnormalities in values for sperm parameters and damages
to testes cytoarchitecture of male mice. The results recorded
decreased viability (p0.05) with degenerative structures in seminiferous tubule of
testes. The results indicated various implications of MSG on male
mice reproductive system which has consequences in fertility
potential.
Abstract: A known iterative computational procedure is used for
internal normal ball loads calculation in statically loaded single-row,
angular-contact ball bearings, subjected to a known thrust load,
which is applied in the inner ring at the geometric bearing center line.
Numerical aspects of the iterative procedure are discussed.
Numerical examples results for a 218 angular-contact ball bearing
have been compared with those from the literature. Twenty figures
are presented showing the geometrical features, the behavior of the
convergence variables and the following parameters as functions of
the thrust load: normal ball loads, contact angle, distance between
curvature centers, and normal ball and axial deflections between the
raceways.
Abstract: In this paper, we studied some properties of geodesic on some open surfaces: Hyperboloid, Paraboloid and Funnel Surface. Geodesic equation in the v-Clairaut parameterization was calculated and reduced to definite integral. Some geodesics on some open surfaces as mention above were classified by Clairaut's relation.
Abstract: Nowadays, the focus on renewable energy and alternative fuels has increased due to increasing oil prices, environment pollution, and also concern on preserving the nature. Biodiesel has been known as an attractive alternative fuel although biodiesel produced from edible oil is very expensive than conventional diesel. Therefore, the uses of biodiesel produced from non-edible oils are much better option. Currently Jatropha biodiesel (JBD) is receiving attention as an alternative fuel for diesel engine. Biodiesel is non-toxic, biodegradable, high lubricant ability, highly renewable, and its use therefore produces real reduction in petroleum consumption and carbon dioxide (CO2) emissions. Although biodiesel has many advantages, but it still has several properties need to improve, such as lower calorific value, lower effective engine power, higher emission of nitrogen oxides (NOX) and greater sensitivity to low temperature. Exhaust gas recirculation (EGR) is effective technique to reduce NOX emission from diesel engines because it enables lower flame temperature and oxygen concentration in the combustion chamber. Some studies succeeded to reduce the NOX emission from biodiesel by EGR but they observed increasing soot emission. The aim of this study was to investigate the engine performance and soot emission by using blended Jatropha biodiesel with different EGR rates. A CI engine that is water-cooled, turbocharged, using indirect injection system was used for the investigation. Soot emission, NOX, CO2, carbon monoxide (CO) were recorded and various engine performance parameters were also evaluated.