Abstract: A novel three-phase active power filter (APF) circuit with photovoltaic (PV) system to improve the quality of service and to reduce the capacity of energy storage capacitor is presented. The energy balance concept and sampling technique were used to simplify the calculation algorithm for the required utility source current and to control the voltage of the energy storage capacitor. The feasibility was verified by using the Pspice simulations and experiments. When the APF mode was used during non-operational period, not only the utilization rate, power factor and power quality could be improved, but also the capacity of energy storage capacitor could sparing. As the results, the advantages of the APF circuit are simplicity of control circuits, low cost, and good transient response.
Abstract: In general fuzzy sets are used to analyze the fuzzy
system reliability. Here intuitionistic fuzzy set theory for analyzing
the fuzzy system reliability has been used. To analyze the fuzzy
system reliability, the reliability of each component of the system as
a triangular intuitionistic fuzzy number is considered. Triangular
intuitionistic fuzzy number and their arithmetic operations are
introduced. Expressions for computing the fuzzy reliability of a
series system and a parallel system following triangular intuitionistic
fuzzy numbers have been described. Here an imprecise reliability
model of an electric network model of dark room is taken. To
compute the imprecise reliability of the above said system, reliability
of each component of the systems is represented by triangular
intuitionistic fuzzy numbers. Respective numerical example is
presented.
Abstract: In this paper, a Web-based e-Training platform that is dedicated to multimodal breast imaging is presented. The assets of this platform are summarised in (i) the efficient representation of the curriculum flow that will permit efficient training; (ii) efficient tagging of multimodal content appropriate for the completion of realistic cases and (iii) ubiquitous accessibility and platform independence via a web-based approach.
Abstract: The influence of physical (external added weight) and
neurophysiological (fatigue) factors on static and dynamic balance in
sport related activities was typified statically by the Romberg test
(one foot flat, eyes open) and dynamically by jumping and hopping
in both horizontal and vertical directions. Twenty healthy males were
participated in this study. In Static condition, added weight increased
body-s inertia and therefore decreased body sway in AP direction
though not significantly. Dynamically, added weight significantly
increased body sway in both ML and AP directions, indicating
instability, and the use of the counter rotating segments mechanism to
maintain balance was demonstrated. Fatigue on the other hand
significantly increased body sway during static balance as a
neurophysiological adaptation primarily to the inverted pendulum
mechanism. Dynamically, fatigue significantly increased body sway
in both ML and AP directions again indicating instability but with a
greater use of counter rotating segments mechanism. Differential
adaptations for each of the two balance mechanisms (inverted
pendulum and counter rotating segments) were found between one
foot flat and two feet flat dynamic conditions, as participants relied
more heavily on the first in the one foot flat conditions and relied
more on the second in the two feet flat conditions.
Abstract: In this paper an extensive verification of the extraction
method (published earlier) that consistently accounts for self-heating
and Early effect to accurately extract both base and thermal resistance
of bipolar junction transistors is presented. The method verification is
demonstrated on advanced RF SiGe HBTs were the extracted results
for the thermal resistance are compared with those from another
published method that ignores the effect of Early effect on internal
base-emitter voltage and the extracted results of the base resistance
are compared with those determined from noise measurements. A
self-consistency of our method in the extracted base resistance and
thermal resistance using compact model simulation results is also
carried out in order to study the level of accuracy of the method.
Abstract: Water pipe network is installed underground and once equipped, it is difficult to recognize the state of pipes when the leak or burst happens. Accordingly, post management is often delayed
after the fault occurs. Therefore, the systematic fault management system of water pipe network is required to prevent the accident and
minimize the loss. In this work, we develop online fault detection system of water pipe network using data of pipes such as flow rate
or pressure. The transient model describing water flow in pipelines
is presented and simulated using MATLAB. The fault situations such
as the leak or burst can be also simulated and flow rate or pressure data when the fault happens are collected. Faults are detected using
statistical methods of fast Fourier transform and discrete wavelet transform, and they are compared to find which method shows the
better fault detection performance.
Abstract: This paper discusses on the use of Spline Interpolation
and Mean Square Error (MSE) as tools to process data acquired from
the developed simulator that shall replicate sea bed logging environment.
Sea bed logging (SBL) is a new technique that uses marine
controlled source electromagnetic (CSEM) sounding technique and is
proven to be very successful in detecting and characterizing hydrocarbon
reservoirs in deep water area by using resistivity contrasts. It uses
very low frequency of 0.1Hz to 10 Hz to obtain greater wavelength.
In this work the in house built simulator was used and was provided
with predefined parameters and the transmitted frequency was varied
for sediment thickness of 1000m to 4000m for environment with and
without hydrocarbon. From series of simulations, synthetics data were
generated. These data were interpolated using Spline interpolation
technique (degree of three) and mean square error (MSE) were
calculated between original data and interpolated data. Comparisons
were made by studying the trends and relationship between frequency
and sediment thickness based on the MSE calculated. It was found
that the MSE was on increasing trends in the set up that has the
presence of hydrocarbon in the setting than the one without. The MSE
was also on decreasing trends as sediment thickness was increased
and with higher transmitted frequency.
Abstract: Optical 1x12 fused-taper-twisted polymer optical fiber (POF) couplers has been fabricated by a perform technique. Characterization of the coupler which proposed to be used in passive night vision application to tracking a blind sport area was reported. During the development process of fused-taper-twisted POF couplers was carried out, red LED fully utilized to be injected into the couplers to test the quality of fabricated couplers. Some characterization parameters, such as optical output power, POFs attenuation characteristics and power losses on the network were observed. The maximum output power efficiency of the coupler is about 40%, but it can be improved gradually through experience and practice.
Abstract: With the turn of this century, many researchers
started showing interest in Embedded Firewall (EF) implementations.
These are not the usual firewalls that are used as checkpoints at network gateways. They are, rather, applied near those hosts that need protection. Hence by using them, individual or grouped network
components can be protected from the inside as well as from external attacks.
This paper presents a study of EF-s, looking at their architecture and problems. A comparative study assesses how practical each kind is. It particularly focuses on the architecture, weak points, and
portability of each kind. A look at their use by different categories of users is also presented.
Abstract: In this paper, a field oriented control (FOC) induction motor drive is presented. In order to eliminate the speed sensor, an adaptation algorithm for tuning the rotor speed is proposed. Based on the Model Reference Adaptive System (MRAS) scheme, the rotor speed is tuned to obtain an exact FOC induction motor drive. The reference and adjustable models, developed in stationary stator reference frame, are used in the MRAS scheme to estimate induction rotor speed from measured terminal voltages and currents. The Integral Proportional (IP) gains speed controller are tuned by a modern approach that is the Particle Swarm Optimization (PSO) algorithm in order to optimize the parameters of the IP controller. The use of PSO as an optimization algorithm makes the drive robust, with faster dynamic response, higher accuracy and insensitive to load variation. The proposed algorithm has been tested by numerical simulation, showing the capability of driving load.
Abstract: Equal Channel Angular Pressing (ECAP) is currently
being widely investigated because of its potential to produce ultrafine
grained microstructures in metals and alloys. A sound
knowledge of the plastic deformation and strain distribution is
necessary for understanding the relationships between strain
inhomogeneity and die geometry. Considerable research has been
reported on finite element analysis of this process, assuming threedimensional
plane strain condition. However, the two-dimensional
models are not suitable due to the geometry of the dies, especially in
cylindrical ones. In the present work, three-dimensional simulation of
ECAP process was carried out for six outer corner radii (sharp to 10
mm in steps of 2 mm), with channel angle 105¶Çü▒, for strain hardening
aluminium alloy (AA 6101) using ABAQUS/Standard software.
Strain inhomogeneity is presented and discussed for all cases. Pattern
of strain variation along selected radial lines in the body of the workpiece
is presented. It is found from the results that the outer corner
has a significant influence on the strain distribution in the body of
work-piece. Based on inhomogeneity and average strain criteria,
there is an optimum outer corner radius.
Abstract: This paper shows the potential system benefits of
simple tracking solar system using a stepper motor and light sensor.
This method is increasing power collection efficiency by developing
a device that tracks the sun to keep the panel at a right angle to its
rays. A solar tracking system is designed, implemented and
experimentally tested. The design details and the experimental results
are shown.
Abstract: This paper proposes an application of the differential
evolution (DE) algorithm for solving the economic dispatch problem
(ED). Furthermore, the regenerating population procedure added to
the conventional DE in order to improve escaping the local minimum
solution. To test performance of DE algorithm, three thermal
generating units with valve-point loading effects is used for testing.
Moreover, investigating the DE parameters is presented. The
simulation results show that the DE algorithm, which had been
adjusted parameters, is better convergent time than other optimization
methods.
Abstract: This research presents the development of simulation
modeling for WIP management in semiconductor fabrication.
Manufacturing simulation modeling is needed for productivity
optimization analysis due to the complex process flows involved
more than 35 percent re-entrance processing steps more than 15 times
at same equipment. Furthermore, semiconductor fabrication required
to produce high product mixed with total processing steps varies from
300 to 800 steps and cycle time between 30 to 70 days. Besides the
complexity, expansive wafer cost that potentially impact the
company profits margin once miss due date is another motivation to
explore options to experiment any analysis using simulation
modeling. In this paper, the simulation model is developed using
existing commercial software platform AutoSched AP, with
customized integration with Manufacturing Execution Systems
(MES) and Advanced Productivity Family (APF) for data collections
used to configure the model parameters and data source. Model
parameters such as processing steps cycle time, equipment
performance, handling time, efficiency of operator are collected
through this customization. Once the parameters are validated, few
customizations are made to ensure the prior model is executed. The
accuracy for the simulation model is validated with the actual output
per day for all equipments. The comparison analysis from result of
the simulation model compared to actual for achieved 95 percent
accuracy for 30 days. This model later was used to perform various
what if analysis to understand impacts on cycle time and overall
output. By using this simulation model, complex manufacturing
environment like semiconductor fabrication (fab) now have
alternative source of validation for any new requirements impact
analysis.
Abstract: This study reports the preparation of soft magnetic
ribbons of Fe-based amorphous alloys using the single-roller melt-spinning technique. Ribbon width varied from 142 mm to 213
mm and, with a thickness of approximately 22 μm ± 2 μm. The microstructure and magnetic properties of the ribbons were
characterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and electrical resistivity measurements (ERM). The amorphous material
properties dependence of the cooling rate and nozzle pressure have uneven surface in ribbon thicknesses are investigated. Magnetic
measurement results indicate that some region of the ribbon exhibits good magnetic properties, higher saturation induction and lower coercivity. However, due to the uneven surface of 213 mm wide
ribbon, the magnetic responses are not uniformly distributed. To
understand the transformer magnetic performances, this study analyzes the measurements of a three-phase 2 MVA amorphous-cored transformer. Experimental results confirm that the transformer with a
ribbon width of 142 mm has better magnetic properties in terms of lower core loss, exciting power, and audible noise.
Abstract: This paper reviews the major contributions to the Motion Planning (MP) field throughout a 35-year period, from classic approaches to heuristic algorithms. Due to the NP-Hardness of the MP problem, heuristic methods have outperformed the classic approaches and have gained wide popularity. After surveying around 1400 papers in the field, the amount of existing works for each method is identified and classified. Especially, the history and applications of numerous heuristic methods in MP is investigated. The paper concludes with comparative tables and graphs demonstrating the frequency of each MP method's application, and so can be used as a guideline for MP researchers.
Abstract: In two studies we challenged the well consolidated
position in regret literature according to which the necessary
condition for the emergence of regret is a bad outcome ensuing from
free decisions. Without free choice, and, consequently, personal
responsibility, other emotions, such as disappointment, but not regret,
are supposed to be elicited. In our opinion, a main source of regret is
being obliged by circumstance out of our control to chose an
undesired option. We tested the hypothesis that regret resulting from
a forced choice is more intense than regret derived from a free choice
and that the outcome affects the latter, not the former. Besides, we
investigated whether two other variables – the perception of the level
of freedom of the choice and the choice justifiability – mediated the
relationships between choice and regret, as well as the other four
emotions we examined: satisfaction, anger toward oneself,
disappointment, anger towards circumstances. The two studies were
based on the scenario methodology and implied a 2 x 2 (choice x
outcome) between design. In the first study the foreseen short-term
effects of the choice were assessed; in the second study the
experienced long-term effects of the choice were assessed. In each
study 160 students of the Second University of Naples participated.
Results largely corroborated our hypotheses. They were discussed in
the light of the main theories on regret and decision making.
Abstract: “Dengue" is an African word meaning “bone
breaking" because it causes severe joint and muscle pain that feels
like bones are breaking. It is an infectious disease mainly transmitted
by female mosquito, Aedes aegypti, and causes four serotypes of
dengue viruses. In recent years, a dramatic increase in the dengue
fever confirmed cases around the equator-s belt has been reported.
Several conventional indices have been designed so far to monitor the
transmitting vector populations known as House Index (HI),
Container Index (CI), Breteau Index (BI). However, none of them
describes the adult mosquito population size which is important to
direct and guide comprehensive control strategy operations since
number of infected people has a direct relationship with the vector
density. Therefore, it is crucial to know the population size of the
transmitting vector in order to design a suitable and effective control
program. In this context, a study is carried out to report a new
statistical index, ABURAS Index, using Poisson distribution based
on the collection of vector population in Jeddah Governorate, Saudi Arabia.
Abstract: Due to heightened concerns over environmental and economic issues the growing important of air pollution, and the importance of conserving fossil fuel resources in the world, the automotive industry is now forced to produce more fuel efficient, low emission vehicles and new drive system technologies. One of the most promising technologies to receive attention is the hybrid electric vehicle (HEV), which consists of two or more energy sources that supply energy to electric traction motors that in turn drive the wheels. This paper presents the various structures of HEV systems, the basic theoretical knowledge for describing their operation and the general behaviour of the HEV in acceleration, cruise and deceleration phases. The conventional design and sizing of a series HEV is studied. A conventional bus and its series configuration are defined and evaluated using the ADVISOR. In this section the simulation of a standard driving cycle and prediction of its fuel consumption and emissions of the HEV are discussed. Finally the bus performance is investigated to establish whether it can satisfy the performance, fuel consumption and emissions requested. The validity of the simulation has been established by the close conformity between the fuel consumption of the conventional bus reported by the manufacturer to what has achieved from the simulation.
Abstract: In this paper, the detection of a fault in the Global Positioning System (GPS) measurement is addressed. The class of faults considered is a bias in the GPS pseudorange measurements. This bias is modeled as an unknown constant. The fault could be the result of a receiver fault or signal fault such as multipath error. A bias bank is constructed based on set of possible fault hypotheses. Initially, there is equal probability of occurrence for any of the biases in the bank. Subsequently, as the measurements are processed, the probability of occurrence for each of the biases is sequentially updated. The fault with a probability approaching unity will be declared as the current fault in the GPS measurement. The residual formed from the GPS and Inertial Measurement Unit (IMU) measurements is used to update the probability of each fault. Results will be presented to show the performance of the presented algorithm.