Abstract: Plate is one of the popular structural elements used in a wide range of industries and structures. They may be subjected to blast loads during explosion events, missile attacks or aircraft attacks. This study is to investigate dynamic responses of the rectangular plate subjected to explosive loads. The effects of material properties and plate thickness on responses of the plate are to be investigated. The compressive pressure is applied to the surface of the plate. Different amounts of thickness in the range from 1mm to 30mm are considered for the plate to evaluate the changes in responses of the plate with respect to plate thickness. Two different properties are considered for the steel. First, the analysis is performed by considering only the elastic-plastic properties for the steel plate. Later on damping is considered to investigate its effects on the responses of the plate. To do analysis, numerical method using a finite element based package ABAQUS is applied. Finally, dynamic responses and graphs showing the relation between maximum displacement of the plate and aim parameters are provided.
Abstract: Effect of alloying on the microstructure and mechanical properties of heat-resisting duplex stainless steel (DSS) for Mg production was investigated in this study. 25Cr-8Ni based DSS’s were cast into rectangular ingots of which the dimension was 350×350×100 mm3 . Nitrogen and Yttrium were added in the range within 0.3 in weight percent. Phase equilibrium was calculated using the FactSage®, thermodynamic software. Hot exposure, high temperature tensile and compression tests were conducted on the ingots at 1230oC, which is operation temperature employed for Mg production by Silico-thermic reduction. The steel with N and Y showed much higher strength than 310S alloy in both tensile and compression tests. By thermal exposition at 1230oC for 200 hrs, hardness of DSS containing N and Y was found to increase. Hot workability of the heat-resisting DSS was evaluated by employing hot rolling at 1230 oC. Hot shortness was observed in the ingot with N and found to disappear after addition of Y.
Abstract: This paper presents a grid synchronization technique based on adaptive notch filter for SPV (Solar Photovoltaic) system along with MPPT (Maximum Power Point Tracking) techniques. An efficient grid synchronization technique offers proficient detection of various components of grid signal like phase and frequency. It also acts as a barrier for harmonics and other disturbances in grid signal. A reference phase signal synchronized with the grid voltage is provided by the grid synchronization technique to standardize the system with grid codes and power quality standards. Hence, grid synchronization unit plays important role for grid connected SPV systems. As the output of the PV array is fluctuating in nature with the meteorological parameters like irradiance, temperature, wind etc. In order to maintain a constant DC voltage at VSC (Voltage Source Converter) input, MPPT control is required to track the maximum power point from PV array. In this work, a variable step size P & O (Perturb and Observe) MPPT technique with DC/DC boost converter has been used at first stage of the system. This algorithm divides the dPpv/dVpv curve of PV panel into three separate zones i.e. zone 0, zone 1 and zone 2. A fine value of tracking step size is used in zone 0 while zone 1 and zone 2 requires a large value of step size in order to obtain a high tracking speed. Further, adaptive notch filter based control technique is proposed for VSC in PV generation system. Adaptive notch filter (ANF) approach is used to synchronize the interfaced PV system with grid to maintain the amplitude, phase and frequency parameters as well as power quality improvement. This technique offers the compensation of harmonics current and reactive power with both linear and nonlinear loads. To maintain constant DC link voltage a PI controller is also implemented and presented in this paper. The complete system has been designed, developed and simulated using SimPower System and Simulink toolbox of MATLAB. The performance analysis of three phase grid connected solar photovoltaic system has been carried out on the basis of various parameters like PV output power, PV voltage, PV current, DC link voltage, PCC (Point of Common Coupling) voltage, grid voltage, grid current, voltage source converter current, power supplied by the voltage source converter etc. The results obtained from the proposed system are found satisfactory.
Abstract: The world crude oil demand is projected to rise to 108.5 million bbl/d by the year 2035. With reserves estimated at 869 billion tonnes worldwide, coal remains an abundant resource. The aim of this work was to produce a high value hydrocarbon liquid product using a Direct Coal Liquefaction (DCL) process at, relatively mild operating conditions. Via hydrogenation, the temperature-staged approach was investigated in a dual reactor lab-scale pilot plant facility. The objectives included maximising thermal dissolution of the coal in the presence of tetralin as the hydrogen donor solvent in the first stage with 2:1 and 3:1 solvent: coal ratios. Subsequently, in the second stage, hydrogen saturation, in particular, hydrodesulphurization (HDS) performance was assessed. Two commercial hydrotreating catalysts were investigated viz. NickelMolybdenum (Ni-Mo) and Cobalt-Molybdenum (Co-Mo). GC-MS results identified 77 compounds and various functional groups present in the first and second stage liquid product. In the first stage 3:1 ratios and liquid product yields catalysed by magnetite were favoured. The second stage product distribution showed an increase in the BTX (Benzene, Toluene, Xylene) quality of the liquid product, branched chain alkanes and a reduction in the sulphur concentration. As an HDS performer and selectivity to the production of long and branched chain alkanes, Ni-Mo had an improved performance over Co-Mo. Co-Mo is selective to a higher concentration of cyclohexane. For 16 days on stream each, Ni-Mo had a higher activity than Co-Mo. The potential to cover the demand for low–sulphur, crude diesel and solvents from the production of high value hydrocarbon liquid in the said process, is thus demonstrated.
Abstract: In the past few years, high consumption of soft drinks
has attracted negative attention world-wide due to its possible
adverse effects, leading the health conscious people to find
alternative nutraceutical or herbal health drinks. In the present study,
a nutraceutical soft drink was developed utilizing some easily
available and well known traditional herbs having nutritional
potential. The key ingredients were selected as bael, amla, lemon
juice, ashwagandha and poppy seeds based on their household routine
use in the summer with proven refreshing, cooling and energetic
feeling since ages. After several trials made, the final composition of
nutraceutical summer soft drink was selected as most suitable
combination based on the taste, physicochemical, microbial and
organoleptic point of view. The physicochemical analysis of the
prepared drink found to contain optimum level of titratable acidity,
total soluble solids and pH which were in accordance of the
commercial recommendations. There were no bacterial colonies
found in the product therefore found within limits. During the nine
point’s hedonic scale sensory evaluation, the drink was strongly liked
for colour, taste, flavour and texture. The formulation was found to
contain flavonoids (80mg/100ml), phenolics (103mg/100ml), vitamin
C (250mg/100ml) and has antioxidant potential (75.52%) apart from
providing several other essential vitamins, minerals and healthy
components. The developed nutraceutical drink provides an
economical and feasible option for the consumers with very good
taste combined with potential health benefits. The present drink is
potentially capable to replace the synthetic soft drinks available in the
market.
Abstract: In this paper, a spatial multiple-kernel fuzzy C-means (SMKFCM) algorithm is introduced for segmentation problem. A linear combination of multiples kernels with spatial information is used in the kernel FCM (KFCM) and the updating rules for the linear coefficients of the composite kernels are derived as well. Fuzzy cmeans (FCM) based techniques have been widely used in medical image segmentation problem due to their simplicity and fast convergence. The proposed SMKFCM algorithm provides us a new flexible vehicle to fuse different pixel information in medical image segmentation and detection of MR images. To evaluate the robustness of the proposed segmentation algorithm in noisy environment, we add noise in medical brain tumor MR images and calculated the success rate and segmentation accuracy. From the experimental results it is clear that the proposed algorithm has better performance than those of other FCM based techniques for noisy medical MR images.
Abstract: In this paper, temperature extremes are forecast by
employing the block maxima method of the Generalized extreme
value(GEV) distribution to analyse temperature data from the
Cameroon Development Corporation (C.D.C). By considering two sets
of data (Raw data and simulated data) and two (stationary and
non-stationary) models of the GEV distribution, return levels analysis
is carried out and it was found that in the stationary model, the
return values are constant over time with the raw data while in the
simulated data, the return values show an increasing trend but with
an upper bound. In the non-stationary model, the return levels of
both the raw data and simulated data show an increasing trend but
with an upper bound. This clearly shows that temperatures in the
tropics even-though show a sign of increasing in the future, there
is a maximum temperature at which there is no exceedence. The
results of this paper are very vital in Agricultural and Environmental
research.
Abstract: Currently, planners try to have more green travel
options to decrease economic, social and environmental problems.
Therefore, this study tries to find significant urban travel factors to be
used to increase the usage of alternative urban travel modes. This
paper attempts to identify the relationship between prominent urban
mobility indicators and daily trips by public transport in 30 cities
from various parts of the world. Different travel modes,
infrastructures and cost indicators were evaluated in this research as
mobility indicators. The results of multi-linear regression analysis
indicate that there is a significant relationship between mobility
indicators and the daily usage of public transport.
Abstract: Due to the interference effects, the intrinsic
aerodynamic parameters obtained from the individual component
testing are always fundamentally different than those obtained for
complete model testing. Consideration and limitation for such testing
need to be taken into account in any design work related to the
component buildup method. In this paper, the scaled model of a
straight rectangular canard of a hybrid buoyant aircraft is tested at 50
m/s in IIUM-LSWT (Low Speed Wind Tunnel). Model and its
attachment with the balance are kept rigid to have results free from
the aeroelastic distortion. Based on the velocity profile of the test
section’s floor; the height of the model is kept equal to the
corresponding boundary layer displacement. Balance measurements
provide valuable but limited information of overall aerodynamic
behavior of the model. Zero lift coefficient is obtained at -2.2o and
the corresponding drag coefficient was found to be less than that at
zero angle of attack. As a part of the validation of low fidelity tool,
plot of lift coefficient plot was verified by the experimental data and
except the value of zero lift coefficients, the overall trend has under
predicted the lift coefficient. Based on this comparative study, a
correction factor of 1.36 is proposed for lift curve slope obtained
from the panel method.
Abstract: Wire Electric Discharge Machining (WEDM) is
thermal machining process capable of machining very hard
electrically conductive material irrespective of their hardness.
WEDM is being widely used to machine micro scale parts with the
high dimensional accuracy and surface finish. The objective of this
paper is to optimize the process parameters of wire EDM to fabricate
the micro channels and to calculate the surface finish and material
removal rate of micro channels fabricated using wire EDM. The
material used is aluminum 6061 alloy. The experiments were
performed using CNC wire cut electric discharge machine. The effect
of various parameters of WEDM like pulse on time (TON) with the
levels (100, 150, 200), pulse off time (TOFF) with the levels (25, 35,
45) and current (IP) with the levels (105, 110, 115) were investigated
to study the effect on output parameter i.e. Surface Roughness and
Material Removal Rate (MRR). Each experiment was conducted
under different conditions of pulse on time, pulse off time and peak
current. For material removal rate, TON and Ip
were the most significant process parameter. MRR increases with the increase in
TON and Ip and decreases with the increase in TOFF. For surface
roughness, TON and Ip have the maximum effect and TOFF was found
out to be less effective.
Abstract: This paper presents an analytical approach for
evaluating distribution system reliability indices in the presence of
distributed generation. Modeling distributed generation and
evaluation of distribution system reliability indices using the
frequency duration technique. Using model implements and case
studies are discussed. Results showed that location of DG and its
effect in distribution reliability indices. In this respect, impact of DG
on distribution system is investigated using the IEEE Roy Billinton
test system (RBTS2) included feeder 1. Therefore, it will help to the
distribution system planners in the DG resource placement.
Abstract: This paper suggests a new internal architecture of
holon based on feature selection model using the combination of
Bees Algorithm (BA) and Artificial Neural Network (ANN). BA is
used to generate features while ANN is used as a classifier to
evaluate the produced features. Proposed system is applied on the
Wine dataset, the statistical result proves that the proposed system is
effective and has the ability to choose informative features with high
accuracy.
Abstract: Malaysia’s green building development is gaining
momentum and green buildings have become a key focus area,
especially within the commercial sector with the encouragement of
government legislation and policy. Due to the emerging awareness
among the market players’ views of the benefits associated with the
ownership of green buildings in Malaysia, there is a need for valuers
to incorporate consideration of sustainability into their assessments of
property market value to ensure the green buildings continue to
increase in the market. This paper analyses the valuers’ current
perception on the valuation practices with regard to the green issues
in Malaysia. The study was based on a survey of registered real estate
valuers and the experts whose work related to valuation in the Klang
Valley area to rate their view regarding the perception on valuation of
green building. The findings present evidence that even though
Malaysian valuers have limited knowledge of green buildings, they
recognise the importance of incorporating the green features in the
valuation process. The inclusion of incorporating the green features
in valuations in practice was hindered by the inadequacy of sufficient
transaction data in the market. Furthermore, valuers experienced
difficulty in identifying what are the various input parameters of
green building and how to adjust it in order to reflect the benefit of
sustainability features correctly in the valuation process. This paper
focuses on the present challenges confronted by Malaysian valuers
with regards to incorporating the green features in their valuation.
Abstract: The Japanese version of the SF-36 has been employed
to assess individuals’ health-related QOL (HRQOL). This study aimed
to clarify the HRQOL of motorists with a spinal cord injury, in order to
compare these individuals' SF-36 scores and national standard values.
A total of 100 motorists with a spinal cord injury participated in this
study. Participants’ HRQOL was evaluated using the Japanese version
of the SF-36 (second edition). The score for each subscale was
standardized based on data on the Japanese population. The average
scores for NPF, NRP, NBP, NGH, NVT, NSF, NRE, and NMH were
10.9, 41.8, 45.9, 47.1, 46.1, 46.7, 46.0, and 47.4 points, respectively.
Subjects showed significantly lower scores for NPF and NRP
compared with national standard values, which were both ≤ 45.0
points, but relatively normal scores for the other items: NBP, NGH,
NVT, NSF, NRE and NMH (> 45.0 points). The average scores for
PCS, MCS and RCS were 21.9, 56.0, and 50.0 points, respectively.
Subjects showed a significantly lower PCS score (≤ 20.0 points);
however, the MCS score was higher (> 55.0 points) along with a
relatively normal RCS score in these individuals (= 50.0 points).
Abstract: The moisture content of densified biomass is a
limiting parameter influencing the quality of this solid biofuel. It
influences its calorific value, density, mechanical strength and
dimensional stability as well as affecting its production process. This
paper deals with experimental research into the effect of moisture
content of the densified material on the final quality of biofuel in the
form of logs (briquettes or pellets). Experiments based on the singleaxis
densification of the spruce sawdust were carried out with a
hydraulic piston press (piston and die), where the densified logs were
produced at room temperature. The effect of moisture content on the
qualitative properties of the logs, including density, change of
moisture, expansion and physical changes, and compressive and
impact resistance were studied. The results show the moisture ranges
required for producing good-quality logs. The experiments were
evaluated and the moisture content of the tested material was
optimized to achieve the optimum value for the best quality of the
solid biofuel. The dense logs also have high-energy content per unit
volume. The research results could be used to develop and optimize
industrial technologies and machinery for biomass densification to
achieve high quality solid biofuel.
Abstract: Healthcare safety has been perceived important. It is
essential to prevent troubles in healthcare processes for healthcare
safety. Trouble prevention is based on trouble prediction using
accumulated knowledge on processes, troubles, and countermeasures.
However, information on troubles has not been accumulated in
hospitals in the appropriate structure, and it has not been utilized
effectively to prevent troubles. In the previous study, however a
detailed knowledge acquisition process for trouble prediction was
proposed, the knowledgebase for countermeasures was not involved.
In this paper, we aim to propose the structure of the knowledgebase for
countermeasures, in the knowledge acquisition process for trouble
prediction in healthcare process. We first design the structure of
countermeasures and propose the knowledge representation form on
countermeasures. Then, we evaluate the validity of the proposal, by
applying it into an actual hospital.
Abstract: The current study aims to highlight the loading
characteristics impact on the time evolution (focusing particularly on
long term effects) of the deformation of realized reinforced concrete
beams. Namely the tension stiffening code provisions (i.e. within
Eurocode 2) are reviewed with a clear intention to reassess their
operational value and predicting capacity. In what follows the
experimental programme adopted along with some preliminary
findings and numerical modeling attempts are presented. For a range of long slender reinforced concrete simply supported
beams (4200 mm) constant static sustained and repeated cyclic
loadings were applied mapping the time evolution of deformation.
All experiments were carried out at the Heavy Structures Lab of the
University of Leeds. During tests the mid-span deflection, creep
coefficient and shrinkage strains were monitored for duration of 90
days. The obtained results are set against the values predicted by
Eurocode 2 and the tools within an FE commercial package (i.e.
Midas FEA) to yield that existing knowledge and practise is at times
over-conservative.
Abstract: Group decision making with multiple attribute has
attracted intensive concern in the decision analysis area. This paper
assumes that the contributions of all the decision makers (DMs) are not
equal to the decision process based on different knowledge and
experience in group setting. The aim of this paper is to develop a novel
approach to determine weights of DMs in the group decision making
problems. In this paper, the weights of DMs are determined in the
group decision environment via angle cosine and projection method.
First of all, the average decision of all individual decisions is defined
as the ideal decision. After that, we define the weight of each decision
maker (DM) by aggregating the angle cosine and projection between
individual decision and ideal decision with associated direction
indicator μ. By using the weights of DMs, all individual decisions are
aggregated into a collective decision. Further, the preference order of
alternatives is ranked in accordance with the overall row value of
collective decision. Finally, an example in a chemical company is
provided to illustrate the developed approach.
Abstract: For the shrimp companies to remain relevant to its local
and international consumers, they must offer new shrimp product and
services. It must work actively not just to create value for the consumer,
but to involve the consumer in co-creating value for shrimp product
innovation in the market. In this theoretical work, we conceptualize the
business concept of value co-creation in the context of shrimp products,
and propose a framework of value co-creation for shrimp product
innovation in shrimp industries. With guidance on value co-creation in
in shrimp industry, and shrimp value chain actors mapped to the
co-creation cycle, companies can use the framework to offer new
shrimp product to consumer communities. Although customer
co-creation is known approach in the world, it is not commonly used
by the companies in Bangladesh. This paper makes an original
contribution by conceptualizing co-creation and set the examples of
best co-creation practices in food sector. The results of the study
provide management with guidelines for successful co-creation
projects with an innovation- and market-oriented approach. The
framework also provides a basis for further research in this area.
Abstract: Drought is one of the most serious problems posing a
grave threat to cereals production including maize. Maize
improvement in drought-stress tolerance poses a great challenge as
the global need for food and bio-energy increases. Thus, the current
study was planned to explore the variations and determine the
performance of target traits of maize hybrids at grain growth stage
under drought conditions during 2014 under Adana, Mediterranean
climate conditions, Turkey. Maize hybrids (Sancia, Indaco,
71May69, Aaccel, Calgary, 70May82, 72May80) were evaluated
under (irrigated and water stress). Results revealed that, grain yield
and yield traits had a negative effects because of water stress
conditions compared with the normal irrigation. As well as, based on
the result under normal irrigation, the maximum biological yield and
harvest index were recorded. According to the differences among
hybrids were found that, significant differences were observed among
hybrids with respect to yield and yield traits under current research. Based on the results, grain weight had more effect on grain yield
than grain number during grain filling growth stage under water
stress conditions. In this concern, according to low drought
susceptibility index (less grain yield losses), the hybrid (Indaco) was
more stable in grain number and grain weight. Consequently, it may
be concluded that this hybrid would be recommended for use in the
future breeding programs for production of drought tolerant hybrids.